Stack heat losses can be minimised by (A) Controlling the excess air (B) Oxygen enrichment of combustion air (C) Using low c.v. fuels (D) Maintaining proper draft in the furnace

Stack heat losses can be minimised by
(A) Controlling the excess air
(B) Oxygen enrichment of combustion air
(C) Using low c.v. fuels
(D) Maintaining proper draft in the furnace
by

1 Answer

Answer :

(A) Controlling the excess air
by

Related questions

Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Description : Oxygen enrichment of combustion air does not result in increase of the (A) Flame temperature (B) Oxygen in the flue gas (C) Stack loss (D) Heat transfer rate in the furnace

Last Answer : (B) Oxygen in the flue gas

Higher furnace temperature cannot be achieved by use of a lean fuel gas in the furnace by (A) Increasing the draft in the furnace (B) Preheating the fuel gas (C) Oxygen enrichment of combustion air (D) Preheating the combustion air

Description : Higher furnace temperature cannot be achieved by use of a lean fuel gas in the furnace by (A) Increasing the draft in the furnace (B) Preheating the fuel gas (C) Oxygen enrichment of combustion air (D) Preheating the combustion air

Last Answer : (A) Increasing the draft in the furnace

Out of the following fuels used in a furnace exhausting flue gas at a temperature of 600°C, the percentage stack loss will be maximum in case ofcomplete combustion of(A) Furnace oil with air(B) Furnace oil with oxygen(C) Blast furnace gas with air(D) Blast furnace gas with oxygen

Description : Out of the following fuels used in a furnace exhausting flue gas at a temperature of 600°C, the percentage stack loss will be maximum in case ofcomplete combustion of (A) Furnace oil with air (B) Furnace oil with oxygen (C) Blast furnace gas with air (D) Blast furnace gas with oxygen

Last Answer : (C) Blast furnace gas with air

In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid fuels (C) Imperfect mixing of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Description : In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid ... of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Last Answer : (C) Imperfect mixing of fuel & air and infiltration of air

Pick out the wrong statement. (A) High concentration of oxygen in flue gas means high stack loss (B) Gaseous fuels require the least % excess air for complete combustion (C) The ratio of fixed carbon to volatile matter percentage in coal is called its 'fuel ratio' (D) Calorific value of natural gas is more than that of LPG

Description : Pick out the wrong statement. (A) High concentration of oxygen in flue gas means high stack loss (B) Gaseous fuels require the least % excess air for complete combustion (C) The ratio of fixed carbon to ... coal is called its 'fuel ratio' (D) Calorific value of natural gas is more than that of LPG

Last Answer : (D) Calorific value of natural gas is more than that of LPG

Use of excess of combustion air in the combustion of fuels results in (A) Heat losses (B) Long flame (C) Condensation of water vapour from the fuel gas (D) None of these

Description : Use of excess of combustion air in the combustion of fuels results in (A) Heat losses (B) Long flame (C) Condensation of water vapour from the fuel gas (D) None of these

Last Answer : (A) Heat losses

Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)

Description : Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Too much of excess air in combustion results in high (A) Fuel consumption for the same heat load (B) Stack gas temperature (C) Percentage of oxygen in flue gases (D) All (A), (B) and (C)

Description : Too much of excess air in combustion results in high (A) Fuel consumption for the same heat load (B) Stack gas temperature (C) Percentage of oxygen in flue gases (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Thermal efficiency of furnaces can be improved by (A) Waste heat recovery from flue gas (B) Minimising heat losses from furnace walls(C) Maintaining proper draught(D) All (A), (B) and (C

Description : Thermal efficiency of furnaces can be improved by (A) Waste heat recovery from flue gas (B) Minimising heat losses from furnace walls (C) Maintaining proper draught (D) All (A), (B) and (C

Last Answer : (D) All (A), (B) and (C

Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Description : Combustion of fuel in a furnace with oxygen enriched air results in higher (A) Flue gas volume (B) Flame temperature (C) Fuel consumption (D) Stack loss

Last Answer : (B) Flame temperature

The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Description : The main drawback of supplying more excess air in the combustion of fuel is the (A) Excessive power requirement of air blower (B) Enhanced sensible heat loss in the flue gas (C) Intermittent and uncontrolled combustion of the fuel (D) High exit flue gas temperature from the furnace

Last Answer : (B) Enhanced sensible heat loss in the flue gas

Fuel economy in furnaces can be achieved by (A) Using oxygen enriched combustion air (B) Preheating the combustion air (C) Reducing the heat loss through furnace openings & doors (D) All (A), (B) and (C

Description : Fuel economy in furnaces can be achieved by (A) Using oxygen enriched combustion air (B) Preheating the combustion air (C) Reducing the heat loss through furnace openings & doors (D) All (A), (B) and (C

Last Answer : (D) All (A), (B) and (C

Black smoke coming out of the chimney of a furnace is an indication of the use of __________ in the furnace. (A) Low amount of excess combustion air (B) Large quantity of excess combustion air(C) Hydrocarbon fuel(D) Pulverised coal as fuel

Description : Black smoke coming out of the chimney of a furnace is an indication of the use of __________ in the furnace. (A) Low amount of excess combustion air (B) Large quantity of excess combustion air (C) Hydrocarbon fuel (D) Pulverised coal as fuel

Last Answer : (A) Low amount of excess combustion air

High excess air in combustion of fuels results in (A) Increased fuel consumption (B) Incomplete combustion (C) Smoky flame (D) None of these

Description : High excess air in combustion of fuels results in (A) Increased fuel consumption (B) Incomplete combustion (C) Smoky flame (D) None of these

Last Answer : (A) Increased fuel consumption

Pick out the wrong statement. (A) Strongly caking coal should not be used in the Lurgi gasifier (B) Acetylene gas cannot be used for illumination purpose (C) Water gas is called blue gas because of the color of the flame, when it is burnt (D) Gaseous fuels require less percentage of excess air for combustion as compared to liquid fuels

Description : Pick out the wrong statement. (A) Strongly caking coal should not be used in the Lurgi gasifier (B) Acetylene gas cannot be used for illumination purpose (C) Water gas is called blue gas ... is burnt (D) Gaseous fuels require less percentage of excess air for combustion as compared to liquid fuels

Last Answer : (B) Acetylene gas cannot be used for illumination purpose

Which of the following advantages is not associated with the use of preheated air for combustion of a fuel in the furnace? (A) Increase in calorific value of the fuel (B) Increase in flame temperature (C) Reduction in scale losses (D) Saving in fuel consumption

Description : Which of the following advantages is not associated with the use of preheated air for combustion of a fuel in the furnace? (A) Increase in calorific value of the fuel (B) Increase in flame temperature (C) Reduction in scale losses (D) Saving in fuel consumption

Last Answer : (A) Increase in calorific value of the fuel

Use of preheated air for combustion of fuel in the furnace, increases the (A) Scale losses of the furnace stock (B) Calorific value of the fuel (C) Flame temperature (D) None of these

Description : Use of preheated air for combustion of fuel in the furnace, increases the (A) Scale losses of the furnace stock (B) Calorific value of the fuel (C) Flame temperature (D) None of these

Last Answer : (C) Flame temperature

Which of the following would require maximum amount of % excess air for complete combustion? (A) Coke oven gas (B) Furnace oil (C) Pulverised coal (D) Lump coal (fixed on chain grate)

Description : Which of the following would require maximum amount of % excess air for complete combustion? (A) Coke oven gas (B) Furnace oil (C) Pulverised coal (D) Lump coal (fixed on chain grate)

Last Answer : (D) Lump coal (fixed on chain grate)

Combustion of pulverised coal compared to the lumpy coal (A) Provides better control of furnace temperature (B) Facilitates combustion with lower excess air (C) Provides higher thermal efficiency & flame temperature (D) All (A), (B) & (C)

Description : Combustion of pulverised coal compared to the lumpy coal (A) Provides better control of furnace temperature (B) Facilitates combustion with lower excess air (C) Provides higher thermal efficiency & flame temperature (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

The main advantage of forced draft over natural draft is that (A) Combustion of fuel is complete (B) Smaller height chimney can be used (C) Furnace control is easier (D) All (A), (B) & (C)

Description : The main advantage of forced draft over natural draft is that (A) Combustion of fuel is complete (B) Smaller height chimney can be used (C) Furnace control is easier (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

The Classical example of redox reaction is Combustion of fossil fuel. During combustion of fossil fuels, the carbon compound in the fossil fuel reacts with oxygen in the presence of a heat source to form carbon dioxide (CO 2 ) and water. Energy is also needed for the fossil fuel to react with oxygen, so the energy used in portion of combustion is an endothermic reaction.

Description : The Classical example of redox reaction is Combustion of fossil fuel. During combustion of fossil fuels, the carbon compound in the fossil fuel reacts with oxygen in the presence of a heat source to ... to react with oxygen, so the energy used in portion of combustion is an endothermic reaction.

Last Answer : Combustion of fossil fuel

Combustion of pulverised coal as compared to that of lump coal (A) Develops a non-luminous flame (B) Develops a low temperature flame (C) Can be done with less excess air (D) Provides a lower rate of heat release

Description : Combustion of pulverised coal as compared to that of lump coal (A) Develops a non-luminous flame (B) Develops a low temperature flame (C) Can be done with less excess air (D) Provides a lower rate of heat release

Last Answer : (C) Can be done with less excess ai

. A special type of liquid transporting device is the diffuser pump, in which __________ are minimised. (A) Bearing losses (B) Disk friction (C) Shock losses (D) Cavitation

Description : . A special type of liquid transporting device is the diffuser pump, in which __________ are minimised. (A) Bearing losses (B) Disk friction (C) Shock losses (D) Cavitation

Last Answer : (C) Shock losses

Which of the following is not increased by using preheated combustion air in place of ordinary air at room temperature? (A) Calorific value of the fuel (B) Flame temperature achieved (C) Speed of combustion of fuel (D) Heat transfer rate to the stock in the furnace

Description : Which of the following is not increased by using preheated combustion air in place of ordinary air at room temperature? (A) Calorific value of the fuel (B) Flame temperature achieved (C) Speed of combustion of fuel (D) Heat transfer rate to the stock in the furnace

Last Answer : (A) Calorific value of the fuel

Acid rains are produced by (a) excess NO2 and SO2 from burning fossil fuels (b) excess production of NH3 by industry and coal gas (c) excess release of carbon monoxide by incomplete combustion (d) excess formation of CO2 by combustion and animal respiration.

Description : Acid rains are produced by (a) excess NO2 and SO2 from burning fossil fuels (b) excess production of NH3 by industry and coal  gas (c) excess release of carbon monoxide by incomplete  combustion (d) excess formation of CO2 by combustion and  animal respiration.

Last Answer : (a) excess NO2 and SO2 from burning fossil fuels

Acid rains are produced by (a) excess NO2 and SO2 from burning fossil fuels (b) excess production of NH3 by industry and coal gas (c) excess release of carbon monoxide by incomplete combustion (d) excess formation of CO2 by combustion and animal respiration.

Description : Acid rains are produced by (a) excess NO2 and SO2 from burning fossil fuels (b) excess production of NH3 by industry and coal gas (c) excess release of carbon monoxide by incomplete combustion (d) excess formation of CO2 by combustion and animal respiration.

Last Answer : (a) excess NO2 and SO2 from burning fossil fuels

To reduce the stack loss, heat recovery from flue gas can be done by (A) Preheating of cold stock (B) Preheating of combustion air (C) Steam generation in waste heat boilers (D) All (A), (B) and (C)

Description : To reduce the stack loss, heat recovery from flue gas can be done by (A) Preheating of cold stock (B) Preheating of combustion air (C) Steam generation in waste heat boilers (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Pick out the wrong statement. (A) Theoretical flame temperature is the temperature attained by the products of combustion, when the fuel is burned without loss or gain of heat (B) Burning the fuel with theoretically required amount of pure oxygen results in attainment of maximum adiabatic flame temperature (C) Burning the fuel with excess pure oxygen results in maximum theoretical flame temperature (D) Adiabatic flame temperatures of actual combustions are always less than the maximum values

Description : Pick out the wrong statement. (A) Theoretical flame temperature is the temperature attained by the products of combustion, when the fuel is burned without loss or gain of heat (B) ... flame temperature (D) Adiabatic flame temperatures of actual combustions are always less than the maximum values

Last Answer : (C) Burning the fuel with excess pure oxygen results in maximum theoretical flame temperature

Short/intense flame is produced during combustion of gaseous fuel by using (A) High amount/current of combustion air(B) Low amount/current of combustion air(C) Preheated secondary air(D) Very little excess air

Description : Short/intense flame is produced during combustion of gaseous fuel by using (A) High amount/current of combustion air (B) Low amount/current of combustion air (C) Preheated secondary air (D) Very little excess air

Last Answer : (A) High amount/current of combustion air

Which of the following accentuates clinkering troubles on furnace grate burning coal? (A) Low reactivity of carbonised residue containing high proportion of iron & sulphur (B) Low forced draft & fuel bed temperature (C) Thick firebed and preheated primary air (D) All (A), (B) and (C)

Description : Which of the following accentuates clinkering troubles on furnace grate burning coal? (A) Low reactivity of carbonised residue containing high proportion of iron & sulphur (B) Low forced draft & fuel bed temperature (C) Thick firebed and preheated primary air (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

What are the losses in a power transformer and mention how these losses can be minimised?

Description : What are the losses in a power transformer and mention how these losses can be minimised?

Last Answer : There are two losses in a transformer. a. Iron losses. b. Copper losses. Iron losses - Iron losses constitutes of two losses. a. Eddy current losses, these are due to the induced emf in the core ... the load current I - current through winding. r - resistance of winding. t - time duration. 

Fuel economy in an industrial furnace operation cannot be achieved by the use of (A) Stoichiometric combustion air (B) Non-preheated combustion air (C) Combustion air not enriched with oxygen (D) Recuperators

Description : Fuel economy in an industrial furnace operation cannot be achieved by the use of (A) Stoichiometric combustion air (B) Non-preheated combustion air (C) Combustion air not enriched with oxygen (D) Recuperators

Last Answer : (A) Stoichiometric combustion air

A carbonaceous fuel (containing no H2 or hydrocarbons) is burnt and the resulting flue gas contains 21% CO2 . It means that (A) 21% excess air has been used for combustion (B) 21% excess oxygen has been used for combustion (C) Complete combustion of fuel has taken place (D) No excess air has been used for combustion

Description : A carbonaceous fuel (containing no H2 or hydrocarbons) is burnt and the resulting flue gas contains 21% CO2 . It means that (A) 21% excess air has been used for combustion (B) 21% excess oxygen has ... (C) Complete combustion of fuel has taken place (D) No excess air has been used for combustion

Last Answer : (C) Complete combustion of fuel has taken place

Oxygen content in a flue gas was found to be 4%. It implies that excess air used for combustion was around __________ percent. (A) 4 (B) 96 (C) 20 (D) 40

Description : Oxygen content in a flue gas was found to be 4%. It implies that excess air used for combustion was around __________ percent. (A) 4 (B) 96 (C) 20 (D) 40

Last Answer : (C) 20

Volumetric composition of flue gas analysed with the Orsat apparatus is : CO2 = 12%, O2 = 8%, CO = nil, N2 = 80%. This flue gas composition indicates that (A) Pure oxygen has been used for combustion (B) Nitrogen percentage in the fuel is very high (C) Excess air has been used for combustion (D) Hydrogen is not present in the fuel

Description : Volumetric composition of flue gas analysed with the Orsat apparatus is : CO2 = 12%, O2 = 8%, CO = nil, N2 = 80%. This flue gas composition indicates that (A) Pure oxygen has been used for combustion ... very high (C) Excess air has been used for combustion (D) Hydrogen is not present in the fuel

Last Answer : (C) Excess air has been used for combustion

If oxygen content in the flue gas rises too high, fuel is being wasted by (A) Incomplete combustion (B) Dry gas/stack gas loss (C) Moisture loss (D) None of these

Description : If oxygen content in the flue gas rises too high, fuel is being wasted by (A) Incomplete combustion (B) Dry gas/stack gas loss (C) Moisture loss (D) None of these

Last Answer : (B) Dry gas/stack gas loss

Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature (C) Heat release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Description : Coke oven gas is a better fuel than blast furnace gas, because of its higher (A) Calorific value, cleanliness and relatively low distribution cost (due to its low specific gravity) (B) Adiabatic flame temperature ... release rate (thus requiring smaller combustion chamber) (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Size of the combustion chamber of a furnace depends upon the (A) Heat release rate of the fuel (B) Preheat temperature of fuel & air (C) Method of mixing the fuel & air (D) All (A), (B) and (C)

Description : Size of the combustion chamber of a furnace depends upon the (A) Heat release rate of the fuel (B) Preheat temperature of fuel & air (C) Method of mixing the fuel & air (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Major sources of noise in furnace operation arises from air inspirators, combustion, side wall vibrations and fluctuation in the process heat load. A 50% increase in fuel firing rate may increase the furnace noise level by about __________ decibels. (A) 3 (B) 30(C) 7 (D) 70

Description : Major sources of noise in furnace operation arises from air inspirators, combustion, side wall vibrations and fluctuation in the process heat load. A 50% increase in fuel firing rate may increase the furnace noise level by about __________ decibels. (A) 3 (B) 30 (C) 7 (D) 70

Last Answer : (A) 3

Heat transfer rate to the charge/stock in a furnace does not depend upon the (A) Type of fuels viz. solid, liquid or gaseous (B) Flue gas temperature (C) Emissivity of refractory walls (D) Initial temperature of the charged stock

Description : Heat transfer rate to the charge/stock in a furnace does not depend upon the (A) Type of fuels viz. solid, liquid or gaseous (B) Flue gas temperature (C) Emissivity of refractory walls (D) Initial temperature of the charged stock

Last Answer : (A) Type of fuels viz. solid, liquid or gaseous

It is easy to detect and monitor excess air a. As oxygen not used for combustion is heated and discharged with the exhaust gases. b. Oxygen is discharged without heating c. Both a. & b. d. None of above

Description : It is easy to detect and monitor excess air a. As oxygen not used for combustion is heated and discharged with the exhaust gases. b. Oxygen is discharged without heating c. Both a. & b. d. None of above

Last Answer : a. As oxygen not used for combustion is heated and discharged with the exhaust gases.

Pick out the wrong statement. (A) Pulverised fuel can be completely burnt with less percentage of excess air compared to lump coal (B) Low grade coal can be used, but generally high volatile matter coals are more suitable for making pulverised fuel (C) Regulation of furnace temperature and atmosphere (oxidising or reducing) is easily possible with pulverised fuel firing (D) None of these

Description : Pick out the wrong statement. (A) Pulverised fuel can be completely burnt with less percentage of excess air compared to lump coal (B) Low grade coal can be used, but generally high volatile ... and atmosphere (oxidising or reducing) is easily possible with pulverised fuel firing (D) None of these

Last Answer : (D) None of these

White smoke coming out of the chimney of a furnace indicates the useof(A) Low excess air(B) Very high excess air(C) Gaseous fuel in the furnace(D) Liquid fuel in the furnace

Description : White smoke coming out of the chimney of a furnace indicates the useof (A) Low excess air (B) Very high excess air (C) Gaseous fuel in the furnace (D) Liquid fuel in the furnace

Last Answer : (B) Very high excess air

During combustion of gaseous fuels, deficiency of air (A) Lengthens the flame (B) Tends to shorten the flame (C) Does not affect the flame length (D) Increases the flame temperature

Description : During combustion of gaseous fuels, deficiency of air (A) Lengthens the flame (B) Tends to shorten the flame (C) Does not affect the flame length (D) Increases the flame temperature

Last Answer : (A) Lengthens the flame

Why is water not suitable for putting out a petrol fire? (1) The oxygen content of water is isolated by petrol and thus it helps in burning (2) Petrol is too inflammable to be extinguished by water (3) The heat required for combustion of petrol is very low (4) Water, being heavy, slips below petrol which thus remains in contact with air and burns

Description : Why is water not suitable for putting out a petrol fire? (1) The oxygen content of water is isolated by petrol and thus it helps in burning (2) Petrol is too inflammable to be extinguished by ... very low (4) Water, being heavy, slips below petrol which thus remains in contact with air and burns

Last Answer : (4) Water, being heavy, slips below petrol which thus remains in contact with air and burns Explanation: Water is not effective on petrol fire because it has higher density than ... while petrol stays afloat and keeps burning. Petrochemical fires are nearly always extinguished with chemical foam.

Why is water not suitable for putting out a petrol fire? (1) The oxygen content of water is isolated by petrol and thus it helps in burning (2) Petrol is too inflammable to be extinguished by water (3) The heat required for combustion of petrol is very low (4) Water, being heavy, slips below petrol which thus remains in contact with air and burns

Description : Why is water not suitable for putting out a petrol fire? (1) The oxygen content of water is isolated by petrol and thus it helps in burning (2) Petrol is too inflammable to be extinguished by ... very low (4) Water, being heavy, slips below petrol which thus remains in contact with air and burns

Last Answer : (4) Water, being heavy, slips below petrol which thus remains in contact with air and burns Explanation: Water is not effective on petrol fire because it has higher density than petrol as a ... extinguished with chemical foam which forms a blanket over the flames and cuts off the oxygen supply.

Why is water not suitable for putting out a petrol fire ? (1) The oxygen content of water is isolated by petrol and thus it helps in burning (2) Petrol is too inflammable to be extinguished by water (3) The heat required for combustion of petrol is very low (4) Water, being heavy, slips below petrol which thus remains in contact with air and burns

Description : Why is water not suitable for putting out a petrol fire ? (1) The oxygen content of water is isolated by petrol and thus it helps in burning (2) Petrol is too inflammable to be extinguished by ... very low (4) Water, being heavy, slips below petrol which thus remains in contact with air and burns 

Last Answer : Water, being heavy, slips below petrol which thus remains in contact with air and burns

Combustion of which fuels from following is source of heat for boiler 1. Wood 2. Coal 3. Oil 4. All of above

Description : Combustion of which fuels from following is source of heat for boiler 1. Wood 2. Coal 3. Oil 4. All of above

Last Answer : 4. All of above

Ingress of cold air in the furnaces through cracks, charging doors, openings etc(A) Reduces the flue gas temperature and makes the furnace atmosphereoxidising(B) Increases the load on the induced draft fan(C) Reduces the furnace draught(D) All (A), (B) and (C)

Description : Ingress of cold air in the furnaces through cracks, charging doors, openings etc (A) Reduces the flue gas temperature and makes the furnace atmosphere oxidising (B) Increases the load on the induced draft fan (C) Reduces the furnace draught (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Heat balance of furnace provides means of determining the (A) Thermal efficiency of the process (B) Sources of heat losses (C) Scope of reduction of heat losses(D) All (A), (B) and (C)

Description : Heat balance of furnace provides means of determining the (A) Thermal efficiency of the process (B) Sources of heat losses (C) Scope of reduction of heat losses (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)