Which of the following accentuates clinkering troubles on furnace grate burning coal? (A) Low reactivity of carbonised residue containing high proportion of iron & sulphur (B) Low forced draft & fuel bed temperature (C) Thick firebed and preheated primary air (D) All (A), (B) and (C)

Which of the following accentuates clinkering troubles on furnace grate
burning coal?
(A) Low reactivity of carbonised residue containing high proportion of iron
& sulphur
(B) Low forced draft & fuel bed temperature
(C) Thick firebed and preheated primary air
(D) All (A), (B) and (C)
by

1 Answer

Answer :

(D) All (A), (B) and (C)
by

Related questions

Which of the following accentuates clinkering trouble on furnace grate burning coal? (A) Low reactivity of carbonised residue containing high proportions of iron & sulphur (B) Low forced draught and fuel bed temperature (C) Thick fire bed and preheated primary air (D) All (A), (B) and (C)

Description : Which of the following accentuates clinkering trouble on furnace grate burning coal? (A) Low reactivity of carbonised residue containing high proportions of iron & sulphur (B) Low forced draught and fuel bed temperature (C) Thick fire bed and preheated primary air (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

During combustion of coal on grate, clinker formation is increased by the (A) Use of thick fire bed (B) Low fusion point of ash (< 1100° C) (C) Use of preheated primary air (D) All (A), (B) & (C)

Description : During combustion of coal on grate, clinker formation is increased by the (A) Use of thick fire bed (B) Low fusion point of ash (< 1100° C) (C) Use of preheated primary air (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid fuels (C) Imperfect mixing of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Description : In practical operation of any furnace, zero oxygen percentage or theoretical CO2 percentage in flue gas is rarely achieved, because of (A) Use of non-preheated combustion air (B) Use of pulverised solid ... of fuel & air and infiltration of air (D) Use of excessive positive draft in the furnace

Last Answer : (C) Imperfect mixing of fuel & air and infiltration of air

In a furnace operation, which is not preheated? (A) Solid fuels (B) Hydrocarbon containing fuel gases (e.g. coke oven gas, refinery gas etc.) (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : In a furnace operation, which is not preheated? (A) Solid fuels (B) Hydrocarbon containing fuel gases (e.g. coke oven gas, refinery gas etc.) (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

The main advantage of forced draft over natural draft is that (A) Combustion of fuel is complete (B) Smaller height chimney can be used (C) Furnace control is easier (D) All (A), (B) & (C)

Description : The main advantage of forced draft over natural draft is that (A) Combustion of fuel is complete (B) Smaller height chimney can be used (C) Furnace control is easier (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Temperature of preheated air used for the transportation of pulverised coal through pipes to the burner of a boiler furnace is restricted to a maximum limit of about 300° C to avoid the (A) Requirement of large volume combustion chamber (B) Risk of explosion (C) Chances of clinker formation (D) Incomplete combustion of coal

Description : Temperature of preheated air used for the transportation of pulverised coal through pipes to the burner of a boiler furnace is restricted to a maximum limit of about 300° C to avoid the (A) ... chamber (B) Risk of explosion (C) Chances of clinker formation (D) Incomplete combustion of coal

Last Answer : (B) Risk of explosion

Which of the following advantages is not associated with the use of preheated air for combustion of a fuel in the furnace? (A) Increase in calorific value of the fuel (B) Increase in flame temperature (C) Reduction in scale losses (D) Saving in fuel consumption

Description : Which of the following advantages is not associated with the use of preheated air for combustion of a fuel in the furnace? (A) Increase in calorific value of the fuel (B) Increase in flame temperature (C) Reduction in scale losses (D) Saving in fuel consumption

Last Answer : (A) Increase in calorific value of the fuel

Use of preheated air for combustion of fuel in the furnace, increases the (A) Scale losses of the furnace stock (B) Calorific value of the fuel (C) Flame temperature (D) None of these

Description : Use of preheated air for combustion of fuel in the furnace, increases the (A) Scale losses of the furnace stock (B) Calorific value of the fuel (C) Flame temperature (D) None of these

Last Answer : (C) Flame temperature

Which of the following is not increased by using preheated combustion air in place of ordinary air at room temperature? (A) Calorific value of the fuel (B) Flame temperature achieved (C) Speed of combustion of fuel (D) Heat transfer rate to the stock in the furnace

Description : Which of the following is not increased by using preheated combustion air in place of ordinary air at room temperature? (A) Calorific value of the fuel (B) Flame temperature achieved (C) Speed of combustion of fuel (D) Heat transfer rate to the stock in the furnace

Last Answer : (A) Calorific value of the fuel

Which of the following would require maximum amount of % excess air for complete combustion? (A) Coke oven gas (B) Furnace oil (C) Pulverised coal (D) Lump coal (fixed on chain grate)

Description : Which of the following would require maximum amount of % excess air for complete combustion? (A) Coke oven gas (B) Furnace oil (C) Pulverised coal (D) Lump coal (fixed on chain grate)

Last Answer : (D) Lump coal (fixed on chain grate)

The reason for excessive clinker formation in gas producers is the (A) Use of coal/coke containing a high % of fines and ash (B) Use of fuel having too low an ash fusion temperature (C) Development of hot spots in the fuel bed and an abnormally high rate of gasification (D) All (A), (B) and (C)

Description : The reason for excessive clinker formation in gas producers is the (A) Use of coal/coke containing a high % of fines and ash (B) Use of fuel having too low an ash fusion temperature (C) Development of hot spots in the fuel bed and an abnormally high rate of gasification (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The advantages of firing pulverised coal in the furnace lies in the fact that, it (A) Permits the use of high ash content coal (B) Permits the use of low fusion point ash coal (C) Accelerates the burning rate and economises on fuel consumption (D) All (A), (B) and (C)

Description : The advantages of firing pulverised coal in the furnace lies in the fact that, it (A) Permits the use of high ash content coal (B) Permits the use of low fusion point ash coal (C) Accelerates the burning rate and economises on fuel consumption (D) All (A), (B) and (C)

Last Answer : (C) Accelerates the burning rate and economises on fuel consumption

The advantage of firing pulverised coal in the furnace lies in the fact, that it (A) Permits the use of high ash content coal (B) Permits the use of low fusion point ash coal(C) Accelerates the burning rate and economises on fuel combustion(D) All (A), (B) and (C)

Description : The advantage of firing pulverised coal in the furnace lies in the fact, that it (A) Permits the use of high ash content coal (B) Permits the use of low fusion point ash coal (C) Accelerates the burning rate and economises on fuel combustion (D) All (A), (B) and (C)

Last Answer : (C) Accelerates the burning rate and economises on fuel combustion

Fuel economy in an industrial furnace operation cannot be achieved by the use of (A) Stoichiometric combustion air (B) Non-preheated combustion air (C) Combustion air not enriched with oxygen (D) Recuperators

Description : Fuel economy in an industrial furnace operation cannot be achieved by the use of (A) Stoichiometric combustion air (B) Non-preheated combustion air (C) Combustion air not enriched with oxygen (D) Recuperators

Last Answer : (A) Stoichiometric combustion air

A travelling grate stoker is meant for the efficient burning of __________ coal. (A) Caking (B) Pulverised (C) Non-caking (D) High ash

Description : A travelling grate stoker is meant for the efficient burning of __________ coal. (A) Caking (B) Pulverised (C) Non-caking (D) High ash

Last Answer : (C) Non-caking

Caking coal is desirable for (A) Burning on travelling grate (B) Coke making (C) Burning on firebars (D) All (A), (B) and (C)

Description : Caking coal is desirable for (A) Burning on travelling grate (B) Coke making (C) Burning on firebars (D) All (A), (B) and (C)

Last Answer : (B) Coke making

Which of the following fuels is the best for burning on chain grate stoker? (A) Non-caking coal (B) Caking coal (C) Coking coal (D) Pulverised coal

Description : Which of the following fuels is the best for burning on chain grate stoker? (A) Non-caking coal (B) Caking coal (C) Coking coal (D) Pulverised coal

Last Answer : (A) Non-caking coal

Pick out the wrong statement. (A) Pulverised fuel can be completely burnt with less percentage of excess air compared to lump coal (B) Low grade coal can be used, but generally high volatile matter coals are more suitable for making pulverised fuel (C) Regulation of furnace temperature and atmosphere (oxidising or reducing) is easily possible with pulverised fuel firing (D) None of these

Description : Pick out the wrong statement. (A) Pulverised fuel can be completely burnt with less percentage of excess air compared to lump coal (B) Low grade coal can be used, but generally high volatile ... and atmosphere (oxidising or reducing) is easily possible with pulverised fuel firing (D) None of these

Last Answer : (D) None of these

Combustion of furnace oil in a furnace (soaking pit) with preheated combustion air at 400°C results in saving of about __________ percentfurnace oil as compared to its combustion with atmospheric air, if the fluegas outlet temperature from the soaking pit is 1200°C.(A) 5(B) 60(C) 20(D) 40

Description : Combustion of furnace oil in a furnace (soaking pit) with preheated combustion air at 400°C results in saving of about __________ percentfurnace oil as compared to its combustion with atmospheric air, if the flue gas outlet temperature from the soaking pit is 1200°C. (A) 5 (B) 60 (C) 20 (D) 40

Last Answer : (C) 20

Short/intense flame is produced during combustion of gaseous fuel by using (A) High amount/current of combustion air(B) Low amount/current of combustion air(C) Preheated secondary air(D) Very little excess air

Description : Short/intense flame is produced during combustion of gaseous fuel by using (A) High amount/current of combustion air (B) Low amount/current of combustion air (C) Preheated secondary air (D) Very little excess air

Last Answer : (A) High amount/current of combustion air

Higher furnace temperature cannot be achieved by use of a lean fuel gas in the furnace by (A) Increasing the draft in the furnace (B) Preheating the fuel gas (C) Oxygen enrichment of combustion air (D) Preheating the combustion air

Description : Higher furnace temperature cannot be achieved by use of a lean fuel gas in the furnace by (A) Increasing the draft in the furnace (B) Preheating the fuel gas (C) Oxygen enrichment of combustion air (D) Preheating the combustion air

Last Answer : (A) Increasing the draft in the furnace

Improper storage condition results in the weathering of coal and spontaneous combustion, which increases its (A) Caking index (B) Yield of carbonised products (C) Friability & oxygen content (D) Calorific value

Description : Improper storage condition results in the weathering of coal and spontaneous combustion, which increases its (A) Caking index (B) Yield of carbonised products (C) Friability & oxygen content (D) Calorific value

Last Answer : (C) Friability & oxygen content

Find false statement about effect of sulphur in fuel? (A) It has heating value (B) It helps in electrostatic precipitation of ash in flue gases (C) It leads to corrosion of air heaters, ducting, etc. if flue gas exit temperature is low (D) It erodes furnace walls

Description : Find false statement about effect of sulphur in fuel? (A) It has heating value (B) It helps in electrostatic precipitation of ash in flue gases (C) It leads to corrosion of air heaters, ducting, etc. if flue gas exit temperature is low (D) It erodes furnace walls

Last Answer : (D) It erodes furnace walls

A liquid/gaseous fuel containing hydrocarbons and high amount of sulphur is burnt with 40% excess air. The flue gas still contains large amount of carbon monoxide. This may be due to the (A) Presence of large quantity of hydrogen in the fuel (B) Low calorific value of the fuel (C) High sulphur content in the fuel (D) Lack of thorough mixing of fuel with air

Description : A liquid/gaseous fuel containing hydrocarbons and high amount of sulphur is burnt with 40% excess air. The flue gas still contains large amount of carbon monoxide. This may be due to the (A) Presence of large ... fuel (C) High sulphur content in the fuel (D) Lack of thorough mixing of fuel with air

Last Answer : (D) Lack of thorough mixing of fuel with air

When the temperature and humidity of air is low, we usually use __________ draft cooling tower. (A) Natural (B) Forced (C) Induced (D) None of these

Description : When the temperature and humidity of air is low, we usually use __________ draft cooling tower. (A) Natural (B) Forced (C) Induced (D) None of these

Last Answer : (A) Natural

Pick out the wrong statement pertaining to the cooling towers. (A) In case of induced draft cooling tower, the fan is placed at the top of the tower (B) Effectiveness of forced draft cooling tower is reduced by the recirculation of the humid and hot discharged air (C) A natural draft cooling tower is recommended to be used, when the air humidity is low and air temperature is also low (D) Effectiveness of a mechanical draft cooling tower is reduced with increase in air wet-bulb temperature

Description : Pick out the wrong statement pertaining to the cooling towers. (A) In case of induced draft cooling tower, the fan is placed at the top of the tower (B) Effectiveness of ... Effectiveness of a mechanical draft cooling tower is reduced with increase in air wet-bulb temperature

Last Answer : (D) Effectiveness of a mechanical draft cooling tower is reduced with increase in air wet-bulb temperature

Softening temperature of coal ash is a measure of the __________ of coal. (A) Caking tendency (B) Coking tendency (C) Clinkering tendency (D) Size stability

Description : Softening temperature of coal ash is a measure of the __________ of coal. (A) Caking tendency (B) Coking tendency (C) Clinkering tendency (D) Size stability

Last Answer : (C) Clinkering tendency

In a forced draft cooling tower, water is cooled from 95 to 80°F by exposure to air with a wet bulb temperature of 70°F. In this case, the (A) Range is 15°F (B) Approach is 10°F (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : In a forced draft cooling tower, water is cooled from 95 to 80°F by exposure to air with a wet bulb temperature of 70°F. In this case, the (A) Range is 15°F (B) Approach is 10°F (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

In a forced draft cooling tower, water is cooled from 95 to 80°F by exposure to air with a wet bulb temperature of 70°F. In this case, the (A) Range is 15°F (B) Approach is 10°F (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : In a forced draft cooling tower, water is cooled from 95 to 80°F by exposure to air with a wet bulb temperature of 70°F. In this case, the (A) Range is 15°F (B) Approach is 10°F (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Advantages of use of preheated combustion air are (A) Saving in fuel consumption (B) Reduction in scale losses (C) Increase in flame temperature (D) All (A), (B) and (C)

Description : Advantages of use of preheated combustion air are (A) Saving in fuel consumption (B) Reduction in scale losses (C) Increase in flame temperature (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Furnace oil consumption in a furnace for a given duty employing preheated combination air (at 300°) may be reduced by about __________ percent as compared to the use of atmospheric combustion air. (A) 5 (B) 10 (C) 20 (D) 35

Description : Furnace oil consumption in a furnace for a given duty employing preheated combination air (at 300°) may be reduced by about __________ percent as compared to the use of atmospheric combustion air. (A) 5 (B) 10 (C) 20 (D) 35

Last Answer : (C) 20

Black smoke coming out of the chimney of a furnace is an indication of the use of __________ in the furnace. (A) Low amount of excess combustion air (B) Large quantity of excess combustion air(C) Hydrocarbon fuel(D) Pulverised coal as fuel

Description : Black smoke coming out of the chimney of a furnace is an indication of the use of __________ in the furnace. (A) Low amount of excess combustion air (B) Large quantity of excess combustion air (C) Hydrocarbon fuel (D) Pulverised coal as fuel

Last Answer : (A) Low amount of excess combustion air

LSHS is a type of furnace oil, which (A) Is more viscous than high viscosity furnace oil (HVFO) (B) Stands for low sulphur heavy stock (C) Is an ideal fuel for metallurgical furnaces due to its lower sulphur content (< 1%(D) All (A), (B) and (C))

Description : LSHS is a type of furnace oil, which (A) Is more viscous than high viscosity furnace oil (HVFO) (B) Stands for low sulphur heavy stock (C) Is an ideal fuel for metallurgical furnaces due to its lower sulphur content (< 1%) (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Correct viscosity of furnace oil at the burner tip for proper atomisation is about 25 centistokes. To reduce the viscosity of high viscosity furnace oil (250 centistokes) to the correct atomisation viscosity (i.e. 25 cst), it should be preheated to about ___________°C. (A) 70 (B) 85 (C) 105 (D) 145

Description : Correct viscosity of furnace oil at the burner tip for proper atomisation is about 25 centistokes. To reduce the viscosity of high viscosity furnace oil (250 centistokes) to the correct atomisation viscosity (i.e. 25 cst), it should be preheated to about ___________°C. (A) 70 (B) 85 (C) 105 (D) 145

Last Answer : (C) 105

A coal that softens and fuses on heating is (A) Classified (B) Carbonised (C) Caking (D) Non-caking

Description : A coal that softens and fuses on heating is (A) Classified (B) Carbonised (C) Caking (D) Non-caking

Last Answer : (C) Caking

Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)

Description : Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

With increase in moisture content of coal, its (A) Calorific value increases sometimes (B) Bulk density always decreases (C) Clinkering tendency during combustion increases (D) None of these

Description : With increase in moisture content of coal, its (A) Calorific value increases sometimes (B) Bulk density always decreases (C) Clinkering tendency during combustion increases (D) None of these

Last Answer : (D) None of these

Overfire burning in a furnace is a phenomenon characterised by (A) Supply of excess fuel (B) Supply of excess air (C) Burning carbon monoxide and other incombustible in upper zone of furnace by supplying more air (D) None of these

Description : Overfire burning in a furnace is a phenomenon characterised by (A) Supply of excess fuel (B) Supply of excess air (C) Burning carbon monoxide and other incombustible in upper zone of furnace by supplying more air (D) None of these

Last Answer : (C) Burning carbon monoxide and other incombustible in upper zone of furnace by supplying more air

Overfire burning" in a furnace is a phenomenon characterised by the (A) Supply of excess fuel (B) Supply of excess air (C) Burning of carbon monoxide and other incombustibles in upper zone of furnace by supplying more air (D) None of these

Description : Overfire burning" in a furnace is a phenomenon characterised by the (A) Supply of excess fuel (B) Supply of excess air (C) Burning of carbon monoxide and other incombustibles in upper zone of furnace by supplying more air (D) None of these

Last Answer : (C) Burning of carbon monoxide and other incombustibles in upper zone of furnace by supplying more air

Blast furnace coke is made from coal by (A) Low temperature carbonisation (B) High temperature carbonisation (C) Medium temperature carbonisation (D) Heating the coal in an oven in presence of air

Description : Blast furnace coke is made from coal by (A) Low temperature carbonisation (B) High temperature carbonisation (C) Medium temperature carbonisation (D) Heating the coal in an oven in presence of air

Last Answer : (B) High temperature carbonisation

Stack heat losses can be minimised by (A) Controlling the excess air (B) Oxygen enrichment of combustion air (C) Using low c.v. fuels (D) Maintaining proper draft in the furnace

Description : Stack heat losses can be minimised by (A) Controlling the excess air (B) Oxygen enrichment of combustion air (C) Using low c.v. fuels (D) Maintaining proper draft in the furnace

Last Answer : (A) Controlling the excess air

Use of pulverised coal in boiler furnace provides (A) High calorific value (B) Better combustion (C) Smokeless burning (D) Less erosion on furnace walls

Description : Use of pulverised coal in boiler furnace provides (A) High calorific value (B) Better combustion (C) Smokeless burning (D) Less erosion on furnace walls

Last Answer : (B) Better combustion

Coast Guard Regulations (46 CFR), require that an indicating light at the propulsion control station will operate if overloading or overheating occurs in a _______________. A. forced draft blower motor B. steering gear motor C. fuel pump motor D. condensate pump motor

Description : Coast Guard Regulations (46 CFR), require that an indicating light at the propulsion control station will operate if overloading or overheating occurs in a _______________. A. forced draft blower motor B. steering gear motor C. fuel pump motor D. condensate pump motor

Last Answer : Answer: B

An overload in which of the listed motors will result in the illumination of an indicating light at the propulsion control station alarm panel? A. Fuel pump motor B. Steering motor C. Condensate pump motor D. Forced draft blower motor

Description : An overload in which of the listed motors will result in the illumination of an indicating light at the propulsion control station alarm panel? A. Fuel pump motor B. Steering motor C. Condensate pump motor D. Forced draft blower motor

Last Answer : Answer: B

Ingress of cold air in the furnaces through cracks, charging doors, openings etc(A) Reduces the flue gas temperature and makes the furnace atmosphereoxidising(B) Increases the load on the induced draft fan(C) Reduces the furnace draught(D) All (A), (B) and (C)

Description : Ingress of cold air in the furnaces through cracks, charging doors, openings etc (A) Reduces the flue gas temperature and makes the furnace atmosphere oxidising (B) Increases the load on the induced draft fan (C) Reduces the furnace draught (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Pick up the correct statement from the following: (A) Steel produced by open hearth process is milder than that obtained by the Bessemer process (B) Engineers prefer open hearth steel for structural purpose as it is more homogenous (C) Basic Bessemer process is suitable for converting poor ore containing a large proportion of sulphur and phosphorus into steel

Description : Pick up the correct statement from the following: (A) Steel produced by open hearth process is milder than that obtained by the Bessemer process (B) Engineers prefer open hearth steel ... is suitable for converting poor ore containing a large proportion of sulphur and phosphorus into steel

Last Answer : Answer: Option D

Acid dew point temperature (ADT) of a flue gas produced by the combustion of a fuel containing 1% sulphur may be about __________ °C. (A) 80 (B) 130 (C) 180 (D) 250

Description : Acid dew point temperature (ADT) of a flue gas produced by the combustion of a fuel containing 1% sulphur may be about __________ °C. (A) 80 (B) 130 (C) 180 (D) 250

Last Answer : (B) 130

In producer gas making furnace, steam is added along with air to mainly control the (A) Fusion of coal ash & clinker formation (B) C. V. of producer gas (C) Temperature of producer gas (D) Tar content in producer gas

Description : In producer gas making furnace, steam is added along with air to mainly control the (A) Fusion of coal ash & clinker formation (B) C. V. of producer gas (C) Temperature of producer gas (D) Tar content in producer gas

Last Answer : (A) Fusion of coal ash & clinker formation

Combustion of pulverised coal compared to the lumpy coal (A) Provides better control of furnace temperature (B) Facilitates combustion with lower excess air (C) Provides higher thermal efficiency & flame temperature (D) All (A), (B) & (C)

Description : Combustion of pulverised coal compared to the lumpy coal (A) Provides better control of furnace temperature (B) Facilitates combustion with lower excess air (C) Provides higher thermal efficiency & flame temperature (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)