Following factors are to be considered while designing a distributor

1 Answer

Answer :

1. While designing the distributor voltage drop calculation is important.

2. Voltage drop in distribution system should be maintained within permissible limit ( ±6%).

3. Layout should be simple in design.

4. It should have less initial cost

5. Make the distribution system with minimum distribution losses.

6. From safety point of view distribution system should maintain proper clearances.

7. Select the cross section of conductor from the result of load densities present & future.

8. While selecting cross section of conductor P.F. of the load should be consider.

9. Power should be available to consumers whenever needed.

10. A steady, non-fluctuating, quality supply (Pure sine wave) should be available to consumers.

11. Distribution system should not be over loaded.

12. Distribution system lay out should not affect the appearance of locality.

13. Before installation of distribution system proposed widening of the road in the near future are to be kept in mind

14. Fault on nearest distribution system should not affect stability of existing distribution system. 

Related questions

Description : List classification of distributor system with their advantages each.

Last Answer : According to scheme of connection there are three types of distribution systems: - 1.Radial (Tree) distribution system 2.Ring mains (Loop) distribution system 3. Grid (interconnected) ... It has highest reliability to maintain supply even when there was maintenance on any one feeder.

Description : State advantages and disadvantages of radial distributor system. 

Last Answer : Advantages of radial distributor system: 1. Design of layout is simple. 2. Capital cost & Erecting cost is less as there is only one feeder. 3. Time required for completion of ... maintain supply to consumers when there is maintenance on feeder. 3. Voltage fluctuations are more.

Description : What factors to be considered while designing compressor housing?

Last Answer : Answer: Operation, Maintenance, Climate conditions, Safety, Economics.

Description : factors to be considered while designing feeders ? 

Last Answer : Following factors are to be considered while designing the Feeder:  1) Current carrying capacity of conductor:- Conductor should have high current carrying capacity. While voltage drop consideration is ... time consuming.  5) Power Factor of load should be consider while designing

Description : Explain the factors to be considered while designing a lighting scheme.

Last Answer : .embed-container { position: relative; padding-bottom: 56.25%; height: 0; overflow: hidden; max-width: 100%; } .embed-container iframe, .embed-container object, .embed-container embed { position: absolute; top: 0; left: 0; width: 100%; height: 100%; }

Description : What parameters or technical particulars are important to be considered while designing protection scheme of the transformer?

Last Answer : 1.Network Diagram showing the position of the transformer in the system 2.kVA or MVA rating of the transformer 3.Fault Level at the transformer 4.Voltage Ratio 5.Winding Connections 6.Per Unit ... Oil Filled 11.Length and area of cross section of the connecting leads between CTs and Relay Panel

Description : Explain the term aseptic techniques. What are the various points to be considered while designing an aseptic room?

Last Answer : Definition: The method which is used to prevent the access of microorganism during the preparation of parenteral product and their testing are called aseptic Technique . Design of aseptic room: 1. Site: ... connection. Vacuum. Disposable waste. 6. Furniture: Shack type. Fume -cupboard.

Description : What factors go into designing the vapor space of kettle type reboiler?

Last Answer : The size of the kettle is determined by several factors. One factor is to provide enough space to slow the vapor velocity down enough for nearly all the liquid droplets to fall back down by ... is typically 8 inches. It is higher for high heat flux kettles. Source: Gulley Computer Associates

Description : Explain the features of flexible AC transmission line (any four). State types of FACTS controller.

Last Answer : Features of flexible AC transmission line:-  1. FACTS increase the reliability of AC grids. 2. It controls the voltage under various load condition 3. It balance reactive power (both ... shunt compensation:- 1. Static synchronous compensator (STATCOM) 2. Static VAR compensator (SVC)

Description : Discuss the effect of transmission line parameters on the performance of transmission line .

Last Answer : Following are the effect on performance of transmission line:  1. Due to resistance (R), voltage drop in transmission line produces 2. Due to resistance (R), copper losses in ... voltage regulation of transmission line gets affected 7. Also power factor of transmission line gets affected

Description : Explain the shackle type insulator with neat sketch. 

Last Answer : Shackle type insulator with neat sketch:  Explanation: * These insulators are clamped to the cross arms by one metal U' clamp with the help of bolts, nuts & ... ) Shackle insulators are also used when line is going straight but in case of vertical conductor configuration only 

Description : State the limitations of EHVAC transmission line. 

Last Answer : Following are the Limitations of EHVAC Transmission:   1. Insulation cost increases as voltage increases 2. Skin effect is more 3. Proximity effect is more. 4. Corona loss increases. 5. Radio ... 18. EHVAC is economical only for bulk amount of power is to be transmitted over long distance. 

Description : Draw and explain the construction of underground cables. 

Last Answer : Underground cables:   OR Explanation:- i) Core or conductor: * It function is carry current. * Cable may have single or more than single core conductor. * Conductor ... handling of cables. * It is similar to bedding & consists of fiborous material such as jute. 

Description : Grid distribution system

Last Answer : Grid distribution system:-  In this system, when the feeder or loop or ring is charged (energized) by two or more than two substations from two or more than two different generating stations then it is known as “Grid distribution system. In this system only one feeder is utilized at a time. 

Description : Define: primary and secondary distribution system 

Last Answer : i) Primary Distribution:  It is a 3-phase, 3-wire transmission line connected in between receiving substation to Distribution substation. OR It is link between receiving substation & ... substation to consumer line. OR It is link between distribution transformer substation & consumer. 

Description :  State the disadvantages of skin effect.

Last Answer : Disadvantages of skin effect:- 1. Full cross section of conductor is not utilized, Therefore effective area of conductor reduces so its resistance increases. 2. Due to increase in resistance, copper ... increases (Since Voltage drop = IR ) 5. So voltage regulation becomes poor (increases) 

Description : List standard voltage level used in India. 

Last Answer : Standard voltage level used in India: * Generation Voltage : 3.3KV, 6.6KV,11KV and 17.5 KV,21KV (Now a days generation voltage is in the range of 11KV- 33KV) * Primary Transmission voltage :- 220 ... voltages in India are 765 KV (750KV), 400KV, 220KV, 132KV, 110KV, 66KV, 33KV, 22KV, 11KV.

Description : List the properties of line insulators in brief

Last Answer : Following are the properties of line insulators:  A) Electrical Properties of insulating material:- 1. It should have high resistance. 2. It should have high breakdown voltage. 3. It should have high ... of insulating material:- 1. It should have longer life. 2. It should have low cost

Description : State the meaning of FACTS and explain in brief d-types facts controller. 

Last Answer : Flexible AC Transmission System (FACTS):- A flexible alternating current transmission system (FACTS) is defined as it is a system composed of static equipment used for the AC transmission of ... so as to increase the transmittable active power. However, more reactive power must be provided.

Description : State the meaning of ferranti effect and proximity effect.  

Last Answer : i) Ferranti effect : When long distance transmission is lightly loaded or there is no load condition than it is observe that receiving end voltage (VR) is found to be greater than sending end ... on conductor causes current in each conductor is re-distributed. This is known as proximity effect.

Description : Define Corona, List its causes and state how it can be avoided. 

Last Answer : Define Corona:  When AC Voltage given across two conductors separated by distance d' as shown figure is increased greater than breakdown voltage of air i.e. 30KV/cm, then air around the conductor gets ... e.g./ using ACSR, bundled conductor 3. By using smooth body conductor and hardware. 

Description : State the condition for selecting site for distribution substation. 

Last Answer : Following condition should be considered while selecting site for distribution sub-station:-  1. Near load center :  Sub-station should be located near load center to reduce cost of Transmission and ... free from earthquake :  To avoid damage to sub-station area should be free earth quake. 

Description : State the effects of low power factor on efficiency and voltage regulation of short transmission lines. 

Last Answer : i) Effect of Low power factor on efficiency:- When power factor of load reduces current drawn by transmission line increases so copper losses in transmission line increases, hence transmission ... increases, so voltage drop in transmission line increases so regulation increases. (Become Poor) 

Description : State the meaning of skin effect and how can it be minimised. 

Last Answer : Meaning of skin effect :  When alternating current flows through conductor it has tendency to flow away from center of conductor. i.e. maximum current density is near skin of conductor and goes on ... whenever possible as Skin effect is absent (Since frequency 0) instead of A.C. supply.  

Description : State the advantages of use of high voltage in transmission of Electric power. 

Last Answer : Advantages: 1. As Transmission voltage increases, current decreases. 2. As current decreases, cross section of conductor decreases. 3. As cross section of conductor decreases, its ... high voltage transmission line, successful interconnection of transmission line is possible than low voltage. 

Description : Differentiate between overhead transmission and underground transmission.

Last Answer : Points Overhead line  Underground cable Capital cost  Less More Erecting cost  Less More Time require for completion of work Less More Flexibility More ... Space consumed Space consumed  No space consumed Appearance Not good  Very good 

Description : State line parameters of transmission line. 

Last Answer : Following are the of Line parameters of transmission line:  1. Resistance  2. Inductance  3. Capacitance

Description : State features of wireless power transmission. 

Last Answer : Features of wireless power transmission:  1. Energy delivered anywhere in the world 2. Zero fuel cost 3. Less losses 4. Less use of copper wires 5. More efficiency 6. Minimum long- ... on cables would never exist in the transmission.  7. Power theft would be not possible at all. 

Description : List different transmission line components used for power transmission.

Last Answer : 1. Supporting structure (pole) 2. Line insulator 3. Overhead conductor 4. V' Cross arm 5. Top pin support 6. Two Pin Cross arm 7. Four pin cross arm 8. Stay set (Stay wire of ... types of fabrication Clamp (A-type, B-Type) 15. Bird guards 16. Vibration damper 17. Jumpers 

Description : State the classification of transmission lines depending on length of transmission lines. 

Last Answer : A) According to Voltage level: ( 2 Marks)  a) High voltage Transmission Line (HV) up to 33 KV  b) Extra High Voltage Transmission Line (EHV) above 33 KV up to 400 KV  c) Ultra ... Transmission Line: - The length of Long transmission Line is above 200KM and its line voltage is above 100KV

Description : State the meaning of Single line diagram.

Last Answer : Meaning of Single line diagram: The single line diagram of a power system is the network which shows the main connections and arrangement of the system components along with their data ( ... breakers, transformers, capacitors, bus bars, and conductors are shown by standardized schematic symbols. 

Description : What organizational requirement need to be considered when designing and formatting the layout of a document?

Last Answer : Need answer

Description : What features should be considered in designing a user interface for a knowledge anagement system?

Last Answer : Design the better business layer and next think about designing the user interface for a knowledge management system

Description : Are there any general rules that should be considered when designing a slurry piping system? The following are items to consider when designing a piping system that will transport slurries:

Last Answer : 1) Whenever possible, piping should be designed to be self-draining 2) Manual draining should be installed to drain sections of the piping when self-draining is not possible 3) Blow-out or ... flanges should be provided every 20 feet of horizontal pipe or after every two changes in direction

Description : Where to get a distributor for cheap?

Last Answer : Hope you are in Australia, go to a good breaker yard. If you are not I don’t know.

Description : How do you change the distributor on a VK commodore?

Last Answer : answer:Is there a Chilton's manual for it? I think it safe to say that most of the people here have never seen a Holden since we have few Aussies. That means that you may have to rely on a ... this yourself!) and it's important not to mess up the firing order or (if applicable) the vacuum hoses.

Description : Toto Distributor

Last Answer : There are a number of web sites on the net that are offering information regarding Toto Distributor. These internet sites are specifically designed for those folks who are on the lookout for Toto Distributor. To Find out More please visit this website: https://partnerworlds.com/

Description : Can an LPG distributor open a sub-distributor?

Last Answer : Need Answer

Description : Which online B2B mobile recharge company is best for retailer agency and distributor?

Last Answer : Aepspe is a B2B Portal offers his Distributor /Retailer the facility of Online Recharge , SMS Recharge , and Mobile App (Android), AEPS, BBPS, Domestic Money Transfer, Trave Booking,Pan Card .

Description : When engine is at 1000 RPM at what rpm is the mechanical distributor?

Last Answer : Need answer

Description : How can I find an authorized sharp tv parts distributor?

Last Answer : You can find an authorized Sharp television parts distributor by searching through Sharp's website for authorized dealers and distributors. You can also get authorized parts from major retailers.

Description : Where can I find a soy candle distributor in Wisconsin?

Last Answer : The Garden Party Wisconsin LLC sells and distributes soy candles. You can find them at http://thegardenparty.com/. If you want to buy retail they have a list of retail locations as well. Here ... /candles/index.htm, depending on your need they have retail, drop shipping, and wholesale needs met.

Description : i'm lookin g for a wellesley manor teak folding chair, they were sold by tjmax. i cannot find this furniture company/distributor on line can you assist thank you?

Last Answer : The company name is Wellesley manor that are located in Wellesley Massasschuttes.

Description : Who is the largest independent distributor for Waterford toasting flutes?

Last Answer : I think this is all based on opinion, but I have found many sites that say that Waterford Crystal Lismore is the largest distributor for Waterford toasting flutes.

Description : What prong on distributor cap does number one wire go on a 1995 chevy 350?

Last Answer : You can find out in the repair manual for you vehicle.

Description : Distributor of height of humans is normal distribution these are some very tall people and some very short people but most people in the middle what is true about this trait?

Last Answer : it is controlled by several differen genes. apex

Description : Ignition timing of a multi-cylinder SI engine can be adjusted by A. rotating the cam shaft B. adjusting the generator pulley C. rotating the distributor D. adjusting the pump pulley

Last Answer : ANSWER : C

Description : Which of the following is not related to spark ignition engine? a. fuel injector b. spark plug c. flywheel d. distributor

Last Answer : ANSWER a. fuel injector

Description : The State bank of India and America‟s which financial company have jointly launched a distribution alliance with travel prepaid cards distributor Centrum? A) Visa B) American Express C) Capital One D) MasterCard E) Amex

Last Answer : D) MasterCard Explanation: India s largest bank, State Bank of India (SBI) and MasterCard announced pilot launch of a distribution alliance with travel prepaid cards distributor Centrum. This ... for it s multicurrency prepaid card and will largely target the corporate customers of the bank.