What is Diversity factor in electrical installations?

What is Diversity factor in electrical installations?
by

1 Answer

Answer :

 Diversity factor is the ratio of the sum of the individual maximum demands of the various subdivisions of a system, or part of a system,
to the maximum demand of the whole system, or part of the system, under consideration. Diversity factor is usually more than one.
by

Related questions

State the need for strictly following safety rules while working in electrical installations.

Description : State the need for strictly following safety rules while working in electrical installations. 

Last Answer : Need for strictly following safety rules while working in electrical installations: 1. To avoid the electrical shock to the human being and to provide safe guard. 2. To minimize the chances ... of the electrical devices. 5. To minimize the chances of mechanical and electrical accidents. 

Which of the following has highest diversity factor? a) Domestic lightning b) Commercial lightning c) Industrial power d) Domestic power

Description : Which of the following has highest diversity factor? a) Domestic lightning b) Commercial lightning c) Industrial power d) Domestic power

Last Answer : Ans: A

When load factor and diversity factor increases ___________ a) cost of electricity decreases b) cost of electricity also increases c) cost of electricity remains same d) cost of electricity increases exponential

Description : When load factor and diversity factor increases ___________ a) cost of electricity decreases b) cost of electricity also increases c) cost of electricity remains same d) cost of electricity increases exponential

Last Answer : Ans: A

Define diversity factor.

Description : Define diversity factor.

Last Answer : Diversity factor is defined as the state of being dissimilar to one another. It is defined as the ratio of sum of the maximum demands of individual consuming units in a group during a specified period ... than one. If the diversity factor is higher, the cost per unit of generation will be lesser.

Can I use Arduino for art installations?

Description : Can I use Arduino for art installations?

Last Answer : Yes, Arduino is often used for art installations by interfacing with various sensors, actuators, and other components to create interactive and dynamic art installations.

Why aren't hog factory farming installations required to have on-sight waste water treatment facilities?

Description : Why aren't hog factory farming installations required to have on-sight waste water treatment facilities?

Last Answer : Whenever you come across anything as grossly disgusting as those monster hog factories or mountain top removal coal mining, you can be certain that something very sleazy has occurred politically. When I heard that ... you will about liberals, but you'll never find that sort of crap in a blue state.

What is the name of the cool park with art installations near Berkeley, CA?

Description : What is the name of the cool park with art installations near Berkeley, CA?

Last Answer : It sounds like the Live Oak Park Fair

Are there any video file types compatible with both Windows XP and OS 10.3 and higher that do not require any extra codec installations or video player installations?

Description : Are there any video file types compatible with both Windows XP and OS 10.3 and higher that do not require any extra codec installations or video player installations?

Last Answer : One I can think of is AVI. I believe Windows media player and Apple’s Quicktime player both handle that without requiring additional codec downloads. In other words, pristine just-purchased-and-unboxed machines (PC or Mac) without internet connections should be able to play AVI files.

Kitchen Services is a licensed air conditioning, heating and ventilation contractor in Los Angeles, California. We specialize in Kitchen Exhaust Systems Installations, Preventive Maintenance and Repairs?

Description : Kitchen Services is a licensed air conditioning, heating and ventilation contractor in Los Angeles, California. We specialize in Kitchen Exhaust Systems Installations, Preventive Maintenance and Repairs?

Last Answer : We provide professional air conditioning, refrigeration and kitchen hood cleaning services in Beverly Hills, Santa Monica and Los Angeles. We install new air conditioning, heating and ventilation ... We install refrigeration equipment including walk-in coolers, walk-in freezers and ice machines.

What are the common mistakes people make with AC installations?

Description : What are the common mistakes people make with AC installations?

Last Answer : The common mistakes people does while AC maintenance and installing are as follows.Incorrect size of the AC unit is a common AC installation mistakeThe first and possibly the most common AC installation mistake ... then he could easily do sloppy wiring work which may not only prove risky but may eve

Human habitations and installations occupy land area

Description : Human habitations and installations occupy land area

Last Answer : Human habitations and installations occupy land area A. 0.366 B. 0.166 C. 0.026 D. 0.006

Which commercial lodging type is located on or near U.S. installations is operated by a commercial lodging company and is corporately branded?

Description : Which commercial lodging type is located on or near U.S. installations is operated by a commercial lodging company and is corporately branded?

Last Answer : reason code

Air force installations perform threat assessments to ensure they are prepared to employ threat-specific countermeasures tailored to support the missions of their instalations?

Description : Air force installations perform threat assessments to ensure they are prepared to employ threat-specific countermeasures tailored to support the missions of their instalations?

Last Answer : 1

This function of your installation drf updates the crisis action team with continuing incident status and request support through the CAT when on-scene requirements surpass the installations inherant cumplative capacities.?

Description : This function of your installation drf updates the crisis action team with continuing incident status and request support through the CAT when on-scene requirements surpass the installations inherant cumplative capacities.?

Last Answer : emergency operations center

estimating on one off new installations will be carried out in how many stages?

Description : estimating on one off new installations will be carried out in how many stages?

Last Answer : two

Pakistan, India exchange list of nuclear installations. This is according to ____ agreement.

Description : Pakistan, India exchange list of nuclear installations. This is according to ____ agreement.

Last Answer : 1988

The plinth area of a building not includes (A) Area of the walls at the floor level (B) Internal shaft for sanitary installations up to 2 sq m. in area (C) Lift and wall including landing (D) Area of cantilevered porch

Description : The plinth area of a building not includes (A) Area of the walls at the floor level (B) Internal shaft for sanitary installations up to 2 sq m. in area (C) Lift and wall including landing (D) Area of cantilevered porch

Last Answer : (D) Area of cantilevered porch

The term power budgeting refers to ∙ A. the cost of cable, connectors, equipment and installation ∙ B. the loss of power due to defective components ∙ C. the total power available minus the attenuation losses ∙ D. the comparative costs of fiber and copper installations

Description : The term power budgeting refers to ∙ A. the cost of cable, connectors, equipment and installation ∙ B. the loss of power due to defective components ∙ C. the total power available minus the attenuation losses ∙ D. the comparative costs of fiber and copper installations

Last Answer : C. the total power available minus the attenuation losses

Which post-installations activities are recommended by SAP after the installation of an SAP ECC 6.06 system? Note: there are 2 correct answered to this question A. Restart your SAP system and check logs for errors B. Install a valid license key C. Copy the user SAP* in client 000 for the number of users involved in the implementation project D. Confirm the installation in an SAP Support ticket

Description : Which post-installations activities are recommended by SAP after the installation of an SAP ECC 6.06 system? Note: there are 2 correct answered to this question A. Restart your SAP system ... of users involved in the implementation project D. Confirm the installation in an SAP Support ticket

Last Answer : A. Restart your SAP system and check logs for errors B. Install a valid license key

_____ are industrial pro ial products t ducts that aid in t hat aid in the buyer he buyer’s produc ’s production or o tion or operations, in ions, including installations and accessory equipment. a. Materials b. Parts c. Capital items d. Specialty products

Description : _____ are industrial pro ial products t ducts that aid in t hat aid in the buyer he buyer’s produc ’s production or o tion or operations, in ions, including installations and accessory equipment. a. Materials b. Parts c. Capital items d. Specialty products

Last Answer : c. Capital items

List the types of Internal wiring in residential installations –

Description : List the types of Internal wiring in residential installations –

Last Answer : 1) Cleat wiring 2) Batten wiring 3) Wooden casing capping wiring 4) PVC conduit wiring 5) PVC casing capping wiring 6) Concealed wiring

Most common form of A.C. meters met with in every day domestic and industrial installations are?

Last Answer : Most common form of A.C. meters met with in every day domestic and industrial installations are induction type single phase energy meters.

To remove an alternator operating in parallel with another unit from the main electrical bus, you must FIRST _________. A. adjust the power factor on both units B. set the desired voltage on the outgoing alternator C. open the circuit breaker on the outgoing alternator D. remove the load from the outgoing alternator

Description : To remove an alternator operating in parallel with another unit from the main electrical bus, you must FIRST _________. A. adjust the power factor on both units B. set the desired voltage on ... C. open the circuit breaker on the outgoing alternator D. remove the load from the outgoing alternator

Last Answer : Answer: D

In an alternating current electrical system, a low system power factor is a direct sign of _____________. A. wasted energy B. efficient operation C. a short in the exciter field windings D. an excessive number of minor system grounds

Description : In an alternating current electrical system, a low system power factor is a direct sign of _____________. A. wasted energy B. efficient operation C. a short in the exciter field windings D. an excessive number of minor system grounds

Last Answer : Answer: A

A current carrying conductor making an electrical contact with a wiring metal conduit is indicated by a _____________. A. low switchboard wattmeter reading B. reading of 1.0 on the power factor meter C. high switchboard voltmeter reading D. totally darkened switchboard ground-detecting light

Description : A current carrying conductor making an electrical contact with a wiring metal conduit is indicated by a _____________. A. low switchboard wattmeter reading B. reading of 1.0 on the power factor meter C. high switchboard voltmeter reading D. totally darkened switchboard ground-detecting light

Last Answer : Answer: D

The operator of electrical motors should keep a constant check on the loads they carry because _____________. A. low loads necessitate frequent insulation cleaning B. exceeding nameplate values shortens useful life C. energy is wasted if full loading is not utilized D. power factor correction methods are load dependent

Description : The operator of electrical motors should keep a constant check on the loads they carry because _____________. A. low loads necessitate frequent insulation cleaning B. exceeding nameplate values shortens ... wasted if full loading is not utilized D. power factor correction methods are load dependent

Last Answer : Answer: B

When you are making a high potential test on a piece of repaired electrical machinery, a rise in leakage current indicates ____________. A. good insulation B. bad insulation C. high insulation power factor D. a high slot discharge factor

Description : When you are making a high potential test on a piece of repaired electrical machinery, a rise in leakage current indicates ____________. A. good insulation B. bad insulation C. high insulation power factor D. a high slot discharge factor

Last Answer : Answer: B

Regarding an AC generator connected to the main electrical bus; as the electric load and power factor vary, a corresponding change is reflected in the generator armature reaction. These changes in armature reaction are compensated for by the __________ A. governor speed droop setting B. voltage regulator C. balance coil D. phase-balance relay

Description : Regarding an AC generator connected to the main electrical bus; as the electric load and power factor vary, a corresponding change is reflected in the generator armature reaction. These changes in ... . governor speed droop setting B. voltage regulator C. balance coil D. phase-balance relay

Last Answer : Answer: B

What is Diversity Factor ?

Description : What is Diversity Factor ?

Last Answer : Diversity factor is the sum of the individual maximum demand and the ratio of the maximum demand of the plant.

The following formula is correct: (A) Diversity factor =1 / Coincidence Factor (B) Diversity factor =1 x

Description : The following formula is correct:  (A) Diversity factor =1 / Coincidence Factor  (B) Diversity factor =1 x Coincidence Factor  (C) Diversity factor =1 - Coincidence Factor  (D) All of the above

Last Answer : The following formula is correct:  (A) Diversity factor =1 / Coincidence Factor  (B) Diversity factor =1 x Coincidence Factor  (C) Diversity factor =1 - Coincidence Factor  (D) All of the above

The knowledge of diversity factor helps in computing

Description : The knowledge of diversity factor helps in computing  (1) Plant capacity (2) Average load (3) Units (kWh) generated (4) Peak demand

Last Answer : The knowledge of diversity factor helps in computing Plant capacity

In an interconnected system, the diversity factor of the whole system?

Last Answer : In an interconnected system, the diversity factor of the whole system increases.

For high value of diversity factor, a power station of given installed capacity will be in a position to supply?

Last Answer : For high value of diversity factor, a power station of given installed capacity will be in a position to supply more number of consumers.

Diversity factor has direct effect on the?

Description : Diversity factor has direct effect on the?

Last Answer : Diversity factor has direct effect on the fixed cost of unit generated.

What is phase angle in electrical engineering ?

Description : What is phase angle in electrical engineering ?

Last Answer : In electrical engineering, phase angle is the angular difference in phase between two sinusoidal waves or signals. It is typically measured in degrees or radians, and it represents the amount of shift or ... and current in an AC circuit can affect the power factor and the efficiency of the circuit.

Which of the following statements is/are true regarding requirements for receptacle outlets aboard vessels? A. Each receptacle outlet operating at 100 volts or more must have a grounding pole. B. Outlets connecting a lifeboat and the vessel's electrical system must have threaded plugs. C. Machinery spaces must contain sufficient outlets for lighting all machinery with a portable light having a 50 foot flexible cord. D. All of the above.

Description : Which of the following statements is/are true regarding requirements for receptacle outlets aboard vessels? A. Each receptacle outlet operating at 100 volts or more must have a grounding pole. B. Outlets ... machinery with a portable light having a 50 foot flexible cord. D. All of the above.

Last Answer : Answer: A

Coast Guard Regulations (46 CFR) state that the minimum conductor size allowed for use in flexible electrical cords is ____________. A. 10 AWG B. 14 AWG C. 18 AWG D. 20 AWG

Description : Coast Guard Regulations (46 CFR) state that the minimum conductor size allowed for use in flexible electrical cords is ____________. A. 10 AWG B. 14 AWG C. 18 AWG D. 20 AWG

Last Answer : Answer: C

When maintenance personnel are working on electrical equipment, all supply switches should be secured in the open position and tagged specifically by the _____________. A. watch engineer B. chief engineer or first assistant C. chief electrician D. person performing the repair

Description : When maintenance personnel are working on electrical equipment, all supply switches should be secured in the open position and tagged specifically by the _____________. A. watch engineer B. chief engineer or first assistant C. chief electrician D. person performing the repair

Last Answer : Answer: D

Before any work on electrical or electronic equipment is performed, which of the following precautions should be carried out? A. De-energize the applicable switchboard bus. B. Bypass the interlocks. C. Secure and tag the supply circuit breaker in the open position. D. Station a man at the circuit supply switch.

Description : Before any work on electrical or electronic equipment is performed, which of the following precautions should be carried out? A. De-energize the applicable switchboard bus. B. Bypass the interlocks. C. ... supply circuit breaker in the open position. D. Station a man at the circuit supply switch.

Last Answer : Answer: C

Which of the following statements concerning electrical cables is correct? A. Where they pass through watertight bulkheads, they should be fitted with watertight stuffing boxes. B. Electric cable coverings should never be grounded. C. Electrical cables must be rigidly held in place by welding of armored cable, or glued in place where nonmetallic insulation is used. D. All of the above.

Description : Which of the following statements concerning electrical cables is correct? A. Where they pass through watertight bulkheads, they should be fitted with watertight stuffing boxes. B. Electric cable coverings should ... , or glued in place where nonmetallic insulation is used. D. All of the above.

Last Answer : Answer: A

Which of the following statements represents the FIRST precaution to be taken prior to working on any installed electrical component? A. Wear rubber gloves and boots. B. Use only approved nonconducting tools. C. Ground the case of the machine before beginning any repairs. D. Open the supply circuits and tag the switches.

Description : Which of the following statements represents the FIRST precaution to be taken prior to working on any installed electrical component? A. Wear rubber gloves and boots. B. Use only approved nonconducting ... the machine before beginning any repairs. D. Open the supply circuits and tag the switches.

Last Answer : Answer: D

The emergency electrical power source on tank vessels over 500 GT on an international voyage, should be capable of continuous operation under emergency load for _____________. A. 6 hours B. 12 hours C. 18 hours D. 24 hours

Description : The emergency electrical power source on tank vessels over 500 GT on an international voyage, should be capable of continuous operation under emergency load for _____________. A. 6 hours B. 12 hours C. 18 hours D. 24 hours

Last Answer : Answer: C

Which of the spaces listed is defined as a 'location requiring an exceptional degree of protection' when considering the installation of shipboard electrical equipment? A. Machinery space B. Chart room C. Console room D. Accommodation space

Description : Which of the spaces listed is defined as a 'location requiring an exceptional degree of protection' when considering the installation of shipboard electrical equipment? A. Machinery space B. Chart room C. Console room D. Accommodation space

Last Answer : Answer: A

In the schematic of the electrical circuit shown in the illustration, what is the value of the total capacitance, when compared to the value of equal individual capacitors? EL-0038 A. Equal B. Half C. Double D. Squared

Description : In the schematic of the electrical circuit shown in the illustration, what is the value of the total capacitance, when compared to the value of equal individual capacitors? EL-0038 A. Equal B. Half C. Double D. Squared

Last Answer : Answer: C

As shown in the illustration, the symbol is used in electrical drawings to designate a ____________. EL-0026 A. limit switch with one set of normally open contacts B. maintaining type push button with an electrical interlock C. sustaining type push button with a mechanical interlock D. normally closed contact held open mechanically by an interlock

Description : As shown in the illustration, the symbol is used in electrical drawings to designate a ____________. EL-0026 A. limit switch with one set of normally open contacts B. maintaining type ... type push button with a mechanical interlock D. normally closed contact held open mechanically by an interlock

Last Answer : Answer: C

The electrical schematic illustrated in figure A, depicts a/an _____________. EL-0059 A. autotransformer B. Delta Wye transformer C. primary EMF generator D. potential transformer

Description : The electrical schematic illustrated in figure A, depicts a/an _____________. EL-0059 A. autotransformer B. Delta Wye transformer C. primary EMF generator D. potential transformer

Last Answer : Answer: D

The electrical diagram shown in the illustration shows _____________. EL-0021 A. 'R1', 'R2', and 'R3' are connected is series B. 'R1', 'R2', and 'R3' are connected in parallel C. the voltages measured across 'R1', 'R2' and 'R3' will be different if 'R1', 'R2' and 'R3' have different values D. the total resistance equals R1 + R2 + R3

Description : The electrical diagram shown in the illustration shows _____________. EL-0021 A. 'R1', 'R2', and 'R3' are connected is series B. 'R1', 'R2', and 'R3' are connected in parallel C. the voltages measured across ... if 'R1', 'R2' and 'R3' have different values D. the total resistance equals R1 + R2 + R3

Last Answer : Answer: B

The electrical diagram shown in the illustration represents a ___________. EL-0054 A. series-wound motor B. shunt-wound motor C. compound-wound motor D. flat-compounded motor

Description : The electrical diagram shown in the illustration represents a ___________. EL-0054 A. series-wound motor B. shunt-wound motor C. compound-wound motor D. flat-compounded motor

Last Answer : Answer: C

Regarding the illustrated electrical schematic, 'S1-P', 'S1-Q', and 'S1-R' represent ____________. EL-0016 A. capacitors B. normally-closed contacts C. normally-open contacts D. normally-closed pushbutton switches

Description : Regarding the illustrated electrical schematic, 'S1-P', 'S1-Q', and 'S1-R' represent ____________. EL-0016 A. capacitors B. normally-closed contacts C. normally-open contacts D. normally-closed pushbutton switches

Last Answer : Answer: C