The plinth area of a building not includes (A) Area of the walls at the floor level (B) Internal shaft for sanitary installations up to 2 sq m. in area (C) Lift and wall including landing (D) Area of cantilevered porch

The plinth area of a building not includes
(A) Area of the walls at the floor level
(B) Internal shaft for sanitary installations up to 2 sq m. in area
(C) Lift and wall including landing
(D) Area of cantilevered porch
by

1 Answer

Answer :

(D) Area of cantilevered porch
by

Related questions

Pick up the incorrect statement from the following: (A) The built up covered area at the floor level of any storey of a building is called plinth area (B) The usable covered area of the rooms of any storey of a building is called carpet area (C) The carpet area of a building along with area of its kitchen, pantry, store, lavatory, bath room and glazed veranda, is called floor area (D) None of thes

Description : Pick up the incorrect statement from the following: (A) The built up covered area at the floor level of any storey of a building is called plinth area (B) The usable covered area of the rooms of ... , pantry, store, lavatory, bath room and glazed veranda, is called floor area (D) None of thes

Last Answer : (D) None of thes

Pick up the incorrect statement from the following: (A) Horizontal D.P.C. is provided at plinth level in internal walls (B) D.P.C. is provided under door and verandah openings (C) Vertical D.P.C. is not provided in internal walls (D) Cement concrete is a rigid damp-proofing material

Description : Pick up the incorrect statement from the following: (A) Horizontal D.P.C. is provided at plinth level in internal walls (B) D.P.C. is provided under door and verandah openings (C) Vertical D.P.C. is not provided in internal walls (D) Cement concrete is a rigid damp-proofing material

Last Answer : Answer: Option B

Brick walls are measured in sq. m if the thickness of the wall is (A) 10 cm (B) 15 cm (C) 20 cm (D) None of these

Description : Brick walls are measured in sq. m if the thickness of the wall is (A) 10 cm (B) 15 cm (C) 20 cm (D) None of these

Last Answer : (A) 10 cm

Pick up the item of work not included in the plinth area estimate (A) Wall thickness (B) Room area (C) W.C. area (D) Courtyard are

Description : Pick up the item of work not included in the plinth area estimate (A) Wall thickness (B) Room area (C) W.C. area (D) Courtyard are

Last Answer : (D) Courtyard area

A steel rod of sectional area 250 sq. mm connects two parallel walls 5 m apart. The nuts at the ends were tightened when the rod was heated to 100°C. If steel = 0.000012/C°, Esteel = 0.2 MN/mm2 , the tensile force developed at a temperature of 50°C, is (A) 80 N/mm2 (B) 100 N/mm2 (C) 120 N/mm2 (D) 150 N/mm2 Answer: Option

Description : A steel rod of sectional area 250 sq. mm connects two parallel walls 5 m apart. The nuts at the  ends were tightened when the rod was heated to 100°C. If steel = 0.000012/C°, Esteel = 0.2  MN/mm2 , the ... N/mm2 (B) 100 N/mm2 (C) 120 N/mm2 (D) 150 N/mm2 Answer: Option 

Last Answer : (C) 120 N/mm

Pick up the correct statement regarding the centre line method of estimating a building (A) Product of the centre line of the walls and area of cross-section of any item, gives total quantity of the item (B) The centre line is worked out separately for different sections of walls of a building (C) The centre line length is reduced by half the layer of main wall joining the partition wall (D) All the above

Description : Pick up the correct statement regarding the centre line method of estimating a building (A) Product of the centre line of the walls and area of cross-section of any item, gives total quantity of the ... length is reduced by half the layer of main wall joining the partition wall (D) All the above

Last Answer : (D) All the above

For 100 sq. m cement concrete (1 : 2: 4) 4 cm thick floor, the quantity of cement required, is (A) 0.90 m3 (B) 0.94 m3 (C) 0.98 m3 (D) 1.00 m3

Description : For 100 sq. m cement concrete (1 : 2: 4) 4 cm thick floor, the quantity of cement required, is (A) 0.90 m3 (B) 0.94 m3 (C) 0.98 m3 (D) 1.00 m3

Last Answer : (B) 0.94 m3

_____ are industrial pro ial products t ducts that aid in t hat aid in the buyer he buyer’s produc ’s production or o tion or operations, in ions, including installations and accessory equipment. a. Materials b. Parts c. Capital items d. Specialty products

Description : _____ are industrial pro ial products t ducts that aid in t hat aid in the buyer he buyer’s produc ’s production or o tion or operations, in ions, including installations and accessory equipment. a. Materials b. Parts c. Capital items d. Specialty products

Last Answer : c. Capital items

In ordinary residential and public buildings, the damp proof course is generally provided at (A) Ground level (B) Plinth level (C) Water table level (D) Midway ground level and water-table level

Description : In ordinary residential and public buildings, the damp proof course is generally provided at (A) Ground level (B) Plinth level (C) Water table level (D) Midway ground level and water-table level

Last Answer : Answer: Option B

The most reliable estimate is (A) Detailed estimate (B) Preliminary estimate (C) Plinth area estimate (D) Cube rate estimate

Description : The most reliable estimate is (A) Detailed estimate (B) Preliminary estimate (C) Plinth area estimate (D) Cube rate estimate

Last Answer : (A) Detailed estimate

An R.C.C. lintel is spanning an opening of 2 m span in a brick wall. The height of the roof is 2.9 m above the floor level and that of the opening is 2.1 m above the floor level. The lintel is to be designed for self weight plus (A) Triangular load of the wall (B) UDL of wall (C) UDL of wall + load from the roof (D) Triangular load + load from the roof

Description : An R.C.C. lintel is spanning an opening of 2 m span in a brick wall. The height of the roof is 2.9 m above the floor level and that of the opening is 2.1 m above the floor level. The lintel is to be ... (B) UDL of wall (C) UDL of wall + load from the roof (D) Triangular load + load from the roof

Last Answer : Answer: Option C

The brick work is measured in sq metre, in case of (A) Honey comb brick work (B) Brick flat soling (C) Half brick walls or the partition (D) All the above

Description : The brick work is measured in sq metre, in case of (A) Honey comb brick work (B) Brick flat soling (C) Half brick walls or the partition (D) All the above

Last Answer : (D) All the above

Horizontal construction joints in concrete walls are generally provided at (A) Soffit level (B) Window sill level (C) Floor level (D) All the above

Description : Horizontal construction joints in concrete walls are generally provided at (A) Soffit level (B) Window sill level (C) Floor level (D) All the above

Last Answer : Answer: Option D

The external length, breadth and height of a closed box are 10cm, 9cm and 7cm respectively. The total inner surface area of the box is 262 sq.cm. If the walls of the box are of uniform thickness “t” cm, then “t” equals a) 1cm b) 23/3 cm c) 28/9 cm d) 42.5 cm

Description : The external length, breadth and height of a closed box are 10cm, 9cm and 7cm respectively. The total inner surface area of the box is 262 sq.cm. If the walls of the box are of uniform thickness “t” cm, then “t” equals a) 1cm b) 23/3 cm c) 28/9 cm d) 42.5 cm

Last Answer : a) 1cm

List the types of Internal wiring in residential installations –

Description : List the types of Internal wiring in residential installations –

Last Answer : 1) Cleat wiring 2) Batten wiring 3) Wooden casing capping wiring 4) PVC conduit wiring 5) PVC casing capping wiring 6) Concealed wiring

Referring of given figure, pick up the correct statement from the following: (A) The total length of centre line of four walls is 20 m (B) Length of long wall out-to-out is 6.80 m (C) Length of short walls in-to-in is 3.20 m (D) All the above

Description : Referring of given figure, pick up the correct statement from the following: (A) The total length of centre line of four walls is 20 m (B) Length of long wall out-to-out is 6.80 m (C) Length of short walls in-to-in is 3.20 m (D) All the above

Last Answer : (D) All the above

The expected out turn of brick work in cement mortar in foundation and plinth per mason per day, is (A) 1.00 m3 (B) 1.25 m3 (C) 1.50 m3 (D) 1.75 m3

Description : The expected out turn of brick work in cement mortar in foundation and plinth per mason per day, is (A) 1.00 m3 (B) 1.25 m3 (C) 1.50 m3 (D) 1.75 m3

Last Answer : (B) 1.25 m3

Which of the following R.C. retaining walls is suitable for heights beyond 6 m? (A) L-shaped wall (B) T-shaped wall (C) Counterfort type (D) All of the above

Description : Which of the following R.C. retaining walls is suitable for heights beyond 6 m? (A) L-shaped wall (B) T-shaped wall (C) Counterfort type (D) All of the above

Last Answer : Answer: Option C

Expansion Joints in masonry walls are provided in wall lengths usater than (A) 10 m (B) 20 m (C) 30 m (D) 40 m

Description : Expansion Joints in masonry walls are provided in wall lengths usater than (A) 10 m (B) 20 m (C) 30 m (D) 40 m

Last Answer : Answer: Option D

Area of steel required per metre width of pavement for a length of 20 m for design wheel load 6300 kg and permissible stress in steel 1400 kg/cm2 , is (A) 70 kg/sq cm (B) 80 kg/sq cm (C) 90 kg/sq cm (D) 100 kg/sq cm

Description : Area of steel required per metre width of pavement for a length of 20 m for design wheel load 6300 kg and permissible stress in steel 1400 kg/cm2 , is (A) 70 kg/sq cm (B) 80 kg/sq cm (C) 90 kg/sq cm (D) 100 kg/sq cm

Last Answer : Answer: Option C

The excavation exceeding 1.5 m in width and 10 sq.m in plan area with a depth not exceeding 30 cm, is termed as (A) Excavation (B) Surface dressing (C) Cutting (D) Surface excavation

Description : The excavation exceeding 1.5 m in width and 10 sq.m in plan area with a depth not exceeding 30 cm, is termed as (A) Excavation (B) Surface dressing (C) Cutting (D) Surface excavation

Last Answer : (D) Surface excavation

If the effective plan area of a warehouse is 54 sq. m, and maximum height of piles permitted is 270 cm, the number of cement bags to be stored, is (A) 2000 bags (B) 2200 bags (C) 2400 bags (D) 2700 bags

Description : If the effective plan area of a warehouse is 54 sq. m, and maximum height of piles permitted is 270 cm, the number of cement bags to be stored, is (A) 2000 bags (B) 2200 bags (C) 2400 bags (D) 2700 bags

Last Answer : Answer: Option D

R.L. of floor at a building is 74.4 m, staff reading on the floor is 1.625 and staff reading when it is held inverted with bottom touching the ceiling of a hall is 2.870; then the height of the ceiling above the floor is (a) 3.593 m (b) 3.953 m (c) 4.495 m (d) 4. 594 m

Description : R.L. of floor at a building is 74.4 m, staff reading on the floor is 1.625 and staff reading when it is held inverted with bottom touching the ceiling of a hall is 2.870; then the height of the ceiling above the floor is (a) 3.593 m (b) 3.953 m (c) 4.495 m (d) 4. 594 m

Last Answer : (c) 4.495 m

To pump water from a water reservoir 3 m deep and maximum water level at 135 m, a pump is installed to lift water up to R.L. 175 m at a constant rate of 36,00,000 litres per hour. If the length of the pipe is 1506 m and f = 0.01, ignoring other minor losses and assuming the economical diameter from Lea's formula D = 1.2 Q, the water horse power of the pump is (A) 400 (B) 450 (C) 500(D) 600

Description : To pump water from a water reservoir 3 m deep and maximum water level at 135 m, a pump is  installed to lift water up to R.L. 175 m at a constant rate of 36,00,000 litres per hour. If the length  of the ... the water horse power of the pump is  (A) 400  (B) 450  (C) 500 (D) 600

Last Answer : (D) 600

The ceiling height of a building is (A) Between ceiling and ground level (B) Between ceiling and floor level (C) Upto roof above ground level (D) Upto ceiling from the ground level

Description : The ceiling height of a building is (A) Between ceiling and ground level (B) Between ceiling and floor level (C) Upto roof above ground level (D) Upto ceiling from the ground level

Last Answer : Answer: Option B

How would I go about building a porch?

Description : How would I go about building a porch?

Last Answer : Yes there is. You can also hire a contractor for it if you wanted. Sites where you can find some of them are as follows: Building A Porch | Lowes.com, and www.front-porch-ideas-and-more.com/how-to-build-a-porch.html.

The depth of the water table at a place is 45 m below the general ground level. To lift water from a deep tube well in such a locality, the type of pump to be installed is (A) Centrifugal pump (B) Reciprocating pump (C) Deep well turbine pump (D) None of these

Description : The depth of the water table at a place is 45 m below the general ground level. To lift water from a  deep tube well in such a locality, the type of pump to be installed is  (A) Centrifugal pump  (B) Reciprocating pump  (C) Deep well turbine pump  (D) None of these 

Last Answer : (C) Deep well turbine pump

The floor of a rectangular hall has a perimeter 250 m. If the cost of painting the four walls at the rate of Rs.10 per m2 is Rs.15000, find the height of the hall. -Maths 9th

Description : The floor of a rectangular hall has a perimeter 250 m. If the cost of painting the four walls at the rate of Rs.10 per m2 is Rs.15000, find the height of the hall. -Maths 9th

Last Answer : Let length, breadth, and height of the rectangular hall be l, b, and h respectively. Area of four walls = 2lh+2bh = 2(l+b)h Perimeter of the floor of hall = 2(l+b) = 250 m Area of four walls = 2( ... of paining the walls is Rs. 15000. 15000 = 2500h Or h = 6 Therefore, the height of the hall is 6 m.

Cost of fittings and their fixing is specified for the following sanitary fittings (A) Water closets (B) Flushing pipes (C) Lavatory basins (D) All the above

Description : Cost of fittings and their fixing is specified for the following sanitary fittings (A) Water closets (B) Flushing pipes (C) Lavatory basins (D) All the above

Last Answer : (D) All the above

Porcelain is used as: (A) Sanitary wares (B) Electric insulators (C) Storage vessels (D) Reactor chambers

Description : Porcelain is used as: (A) Sanitary wares (B) Electric insulators (C) Storage vessels (D) Reactor chambers

Last Answer : Answer: Option D

For sanitary pipes and chemical stonewares, (A) Salt glazing is used (B) Lead glazing is used (C) Opaque glazing is used (D) None of thes

Description : For sanitary pipes and chemical stonewares, (A) Salt glazing is used (B) Lead glazing is used (C) Opaque glazing is used (D) None of these

Last Answer : Answer: Option A

The loading limitations shall include: a. All limiting mass and centre of gravity b. All limiting mass, centre of gravity position, mass distribution and floor landing c. All limiting mass, centre of gravity position and floor loading d. All limiting mass, mass distributions and centre of gravity

Description : The loading limitations shall include: a. All limiting mass and centre of gravity b. All limiting mass, centre of gravity position, mass distribution and floor landing c. All limiting mass, ... of gravity position and floor loading d. All limiting mass, mass distributions and centre of gravity

Last Answer : b. All limiting mass, centre of gravity position, mass distribution and floor landing

The loading limitations shall include: a. All limiting mass and centre of gravity b. All limiting mass, centre of gravity position, mass distribution and floor landing c. All limiting mass, centre of gravity position and floor loading d. All limiting mass, mass distributions and centre of gravity

Description : The loading limitations shall include: a. All limiting mass and centre of gravity b. All limiting mass, centre of gravity position, mass distribution and floor landing c. All limiting mass ... of gravity position and floor loading d. All limiting mass, mass distributions and centre of gravity

Last Answer : b. All limiting mass, centre of gravity position, mass distribution and floor landing

Human habitations and installations occupy land area

Description : Human habitations and installations occupy land area

Last Answer : Human habitations and installations occupy land area A. 0.366 B. 0.166 C. 0.026 D. 0.006

Pick up the incorrect statement from the following: (A) Dimensions are measured to the nearest 0.01 m (B) Areas are measured to the nearest 0.01 sq.m (C) Cubic contents are measured to the nearest 0.1 cum (D) Weights are measured to the nearest 0.001 tonnes

Description : Pick up the incorrect statement from the following: (A) Dimensions are measured to the nearest 0.01 m (B) Areas are measured to the nearest 0.01 sq.m (C) Cubic contents are measured to the nearest 0.1 cum (D) Weights are measured to the nearest 0.001 tonnes

Last Answer : (D) Weights are measured to the nearest 0.001 tonnes

Pick up the incorrect statement from the following: (A) No deduction is made for the volume occupied by reinforcement (B) No deduction is made for the openings upto 0.1 sq.m (C) No deduction is made for volumes occupied by pipes, not exceeding 100 sq.cm in crosssection (D) None of these

Description : Pick up the incorrect statement from the following: (A) No deduction is made for the volume occupied by reinforcement (B) No deduction is made for the openings upto 0.1 sq.m (C) No deduction is made for volumes occupied by pipes, not exceeding 100 sq.cm in crosssection (D) None of these

Last Answer : (D) None of these

Pick up the correct statement from the following: (A) Pointing is measured in sq.m (B) Plastering is measured in sq.m (C) Glazing is measured in sq.m (D) All the above

Description : Pick up the correct statement from the following: (A) Pointing is measured in sq.m (B) Plastering is measured in sq.m (C) Glazing is measured in sq.m (D) All the above

Last Answer : (D) All the above

A simply supported beam 6 m long and of effective depth 50 cm, carries a uniformly distributed load 2400 kg/m including its self weight. If the lever arm factor is 0.85 and permissible tensile stress of steel is 1400 kg/cm2 , the area of steel required, is (A) 14 cm(B) 15 cm2(C) 16 cm2(D) 17 cm

Description : A simply supported beam 6 m long and of effective depth 50 cm, carries a uniformly distributed load 2400 kg/m including its self weight. If the lever arm factor is 0.85 and permissible tensile stress of steel is 1400 kg/cm2 ... area of steel required, is (A) 14 cm (B) 15 cm2 (C) 16 cm2 (D) 17 cm

Last Answer : Answer: Option C

The item of steel work which is measured in sq.m, is (A) Collapsible gates (B) Rolling shutters (C) Ventilators and glazing (D) All the above

Description : The item of steel work which is measured in sq.m, is (A) Collapsible gates (B) Rolling shutters (C) Ventilators and glazing (D) All the above

Last Answer : (D) All the above

For 12 mm thick cement plastering 1 : 6 on 100 sq.m new brick work, the quantity of cement required, is (A) 0.200 m3 (B) 0.247 m3 (C) 0.274 m3 (D) 0.295 m

Description : For 12 mm thick cement plastering 1 : 6 on 100 sq.m new brick work, the quantity of cement required, is (A) 0.200 m3 (B) 0.247 m3 (C) 0.274 m3 (D) 0.295 m

Last Answer : (C) 0.274 m3

The expected out turn of 12 mm plastering with cement mortar is (A) 2.5 sq m (B) 4.0 sq m (C) 6.0 sq m (D) 8.0 sq m

Description : The expected out turn of 12 mm plastering with cement mortar is (A) 2.5 sq m (B) 4.0 sq m (C) 6.0 sq m (D) 8.0 sq m

Last Answer : (D) 8.0 sq m

The item of the brick structure measured in sq.m, is (A) Reinforced brick work (B) Broken glass coping (C) Brick edging (D) Brick work in arches

Description : The item of the brick structure measured in sq.m, is (A) Reinforced brick work (B) Broken glass coping (C) Brick edging (D) Brick work in arches

Last Answer : (B) Broken glass coping

The minimum thickness of walls built in cement mortar (1 : 6) for a single storey building, is (A) 10 cm (B) 15 cm (C) 20 cm (D) 25 cm

Description : The minimum thickness of walls built in cement mortar (1 : 6) for a single storey building, is (A) 10 cm (B) 15 cm (C) 20 cm (D) 25 cm

Last Answer : Answer: Option C

What is the meaning of the word Plinth ?

Description : What is the meaning of the word Plinth ?

Last Answer : stambapith , stambhumul , vithimul etc.

State any two purposes of Plinth

Description : State any two purposes of Plinth

Last Answer : Purposes of Plinth: 1. To prevent entry of flood water into building. 2. To avoid dust, Insects, Reptiles, etc entries inside the building 3. To facilitate easy drainage of sewage water. 4. To ... wall & transfer load to footing. 6. To prevent from dampness. 7. To support flooring tiles.

How to glue a ceiling plinth?

Description : How to glue a ceiling plinth?

Last Answer : Ceiling plinth is used to decorate the angle between the wall and the ceiling. This decorative element is also called fillet. Installation is carried out after leveling the walls and ceiling. We ... After completing the process, the ceiling plinth is painted, usually in the color of the ceiling.

The exercise of due professional care requires that an auditor a. Use error-free judgment. b. Consider internal control, including tests of controls. c. Critically review the work done at every level of supervision. d. Examine all corroborating evidence available.

Description : The exercise of due professional care requires that an auditor a. Use error-free judgment. b. Consider internal control, including tests of controls. c. Critically review the work done at every level of supervision. d. Examine all corroborating evidence available.

Last Answer : Critically review the work done at every level of supervision

The reduced level of a floor is 99.995 m, the staff reading on the floor is 1.505 m. If the inverted staff reading against the roof is 1.795 m, the floor level below the slab, is (A) 3.290 m (B) 3.300 m (C) 3.275 m (D) 2.790 m

Description : The reduced level of a floor is 99.995 m, the staff reading on the floor is 1.505 m. If the inverted staff reading against the roof is 1.795 m, the floor level below the slab, is (A) 3.290 m (B) 3.300 m (C) 3.275 m (D) 2.790 m

Last Answer : (B) 3.300 m

Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm

Description : Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm

Last Answer : c. 587.1 mm

The effective span of a simply supported slab, is (A) Distance between the centres of the bearings (B) Clear distance between the inner faces of the walls plus twice the thickness of the wall (C) Clear span plus effective depth of the slab (D) None of these

Description : The effective span of a simply supported slab, is (A) Distance between the centres of the bearings (B) Clear distance between the inner faces of the walls plus twice the thickness of the wall (C) Clear span plus effective depth of the slab (D) None of these

Last Answer : Answer: Option B