As load is added to a shunt motor, the motor will _________. A. speed up B. continue to operate at the same speed C. slow down slightly D. stop

As load is added to a shunt motor, the motor will _________. A. speed up B. continue to operate at the same speed  C. slow down slightly D. stop
by

1 Answer

Answer :

Answer: C
by

Related questions

If a unloaded shunt motor's field were weakened by rheostat resistance or by an open circuit, the motor would _________. A. overspeed due to reduced CEMF B. stop because of low flux C. continue to run at base speed D. slow down and overheat

Description : If a unloaded shunt motor's field were weakened by rheostat resistance or by an open circuit, the motor would _________. A. overspeed due to reduced CEMF B. stop because of low flux C. continue to run at base speed D. slow down and overheat

Last Answer : Answer: A

A salient pole synchronous motor is running at no load. Its field current is switched off. The motor will (A) come to stop. (B) continue to run at synchronous speed. (C) continue to run at a speed slightly more than the synchronous speed. (D) continue to run at a speed slightly less than the synchronous speed.

Description : A salient pole synchronous motor is running at no load. Its field current is switched off. The motor will (A) come to stop. (B) continue to run at synchronous speed. (C) continue to run at ... more than the synchronous speed. (D) continue to run at a speed slightly less than the synchronous speed.

Last Answer : (B) continue to run at synchronous speed.

If the energy input is significantly reduced to the prime mover of one shipboard alternator operating in parallel with others, that alternator will _____________. A. continue to operate at no load B. lose its load and overspeed C. begin to motorize and then trip out D. slow down and operate at reduced load

Description : If the energy input is significantly reduced to the prime mover of one shipboard alternator operating in parallel with others, that alternator will _____________. A. continue to operate at no load B. lose ... overspeed C. begin to motorize and then trip out D. slow down and operate at reduced load

Last Answer : Answer: C

Which of the following conditions will occur if the solenoid coil burns out on a cargo winch with an electrical brake? A. The brake will be set by spring force. B. The motor will overspeed and burn up. C. The load suspended from the cargo boom will fall. D. Nothing will happen; the winch will continue to operate as usual.

Description : Which of the following conditions will occur if the solenoid coil burns out on a cargo winch with an electrical brake? A. The brake will be set by spring force. B. The motor will overspeed and burn ... the cargo boom will fall. D. Nothing will happen; the winch will continue to operate as usual.

Last Answer : Answer: A

If a three-phase induction motor is operated under a light load and it develops an open in one of its supply lines, the motor will _____________. A. continue to run, but will vibrate and have reduced torque B. speed up due to the reduced number of poles C. run cooler due to reduced current flow D. stop

Description : If a three-phase induction motor is operated under a light load and it develops an open in one of its supply lines, the motor will _____________. A. continue to run, but will vibrate and have reduced ... speed up due to the reduced number of poles C. run cooler due to reduced current flow D. stop

Last Answer : Answer: A

If field excitation is suddenly lost to an alternator operating in parallel, that alternator will _____________. A. supply excessive current to the bus B. operate at the same load, but with reduced voltage C. lose its load and tend to overspeed D. become overloaded and slow down

Description : If field excitation is suddenly lost to an alternator operating in parallel, that alternator will _____________. A. supply excessive current to the bus B. operate at the same load, but with reduced voltage C. lose its load and tend to overspeed D. become overloaded and slow down

Last Answer : Answer: C

A dc shunt generator has a speed of 800 rpm when delivering 20 A to the load at the terminal voltage of 220V. If the same machine is run as a motor it takes a line current of 20A from 220V supply. The speed of the machine as a motor will be (A) 800 rpm. (B) more than 800 rpm. (C) less than 800 rpm. (D) both higher or lower than 800 rpm.

Description : A dc shunt generator has a speed of 800 rpm when delivering 20 A to the load at the terminal voltage of 220V. If the same machine is run as a motor it takes a line current of 20A from 220V supply. The speed of ... . (B) more than 800 rpm. (C) less than 800 rpm. (D) both higher or lower than 800 rpm.

Last Answer : (C) less than 800 rpm.

If a three-phase induction motor malfunctions and drops to a single-phase (one supply line open) ____________. A. the motor will continue to run if it is not heavily loaded B. more torque will be developed C. the motor will immediately stop and not be able to be restarted D. the motor will immediately stop and can only be restarted at no load

Description : If a three-phase induction motor malfunctions and drops to a single-phase (one supply line open) ____________. A. the motor will continue to run if it is not heavily loaded B. more torque will be ... be able to be restarted D. the motor will immediately stop and can only be restarted at no load

Last Answer : Answer: A

A d.c. shunt motor runs at no load speed of 1140 r.p.m. At full load, armature reaction weakens the main flux by 5% whereas the armature circuit voltage drops by 10%. The motor full load speed in r.p.m. is (A) 1080 (B) 1203 (C) 1000 (D) 1200

Description : A d.c. shunt motor runs at no load speed of 1140 r.p.m. At full load, armature reaction weakens the main flux by 5% whereas the armature circuit voltage drops by 10%. The motor full load speed in r.p.m. is (A) 1080 (B) 1203 (C) 1000 (D) 1200

Last Answer : (A) 1080

The speed of a d.c. shunt motor at no-load is (A) 5 to 10% (B) 15 to 20% (C) 25 to 30% (D) 35 to 40% higher than its speed at rated load.

Description : The speed of a d.c. shunt motor at no-load is (A) 5 to 10% (B) 15 to 20% (C) 25 to 30% (D) 35 to 40% higher than its speed at rated load.

Last Answer : (A) 5 to 10%

If you were driving down the freeway at nighttime during construction work and spotted several Highway Patrol officers near the construction area with their lights on would you a: speed up b: slow down c: continue at the same speed (assuming that this is a multi-lane freeway and you are able to go at or above typical freeway speeds)

Description : If you were driving down the freeway at nighttime during construction work and spotted several Highway Patrol officers near the construction area with their lights on would you a: speed up b: slow down c: ... this is a multi-lane freeway and you are able to go at or above typical freeway speeds)

Last Answer : I always slow down for construction sites. Those “My Daddy Works Here!” signs got me.

In the illustrated device, the part labeled '1A' _________. EL-0001 A. are start and run windings for a single phase shaded pole induction motor B. is the stator for a polyphase induction motor C. is the armature for a squirrel cage rotor motor D. are direct current shunt field windings for a universal motor

Description : In the illustrated device, the part labeled '1A' _________. EL-0001 A. are start and run windings for a single phase shaded pole induction motor B. is the stator for a polyphase induction ... armature for a squirrel cage rotor motor D. are direct current shunt field windings for a universal motor

Last Answer : Answer: B

Which of the listed motors will operate at the highest RPM, assuming that each operates at the same frequency? A. A four-pole synchronous motor under normal load. B. A four-pole induction motor under no load. C. A six-pole synchronous motor under normal load. D. A six-pole induction motor under full load.

Description : Which of the listed motors will operate at the highest RPM, assuming that each operates at the same frequency? A. A four-pole synchronous motor under normal load. B. A four-pole induction motor under ... A six-pole synchronous motor under normal load. D. A six-pole induction motor under full load.

Last Answer : Answer: A

Which of the listed precautions should be observed before spraying liquid solvent on the insulation of an electric motor? A. Slow the motor down to low speed. B. Disconnect the motor from the power source. C. Secure all ventilation in the area. D. Preheat the insulation to assist in cleaning.

Description : Which of the listed precautions should be observed before spraying liquid solvent on the insulation of an electric motor? A. Slow the motor down to low speed. B. Disconnect the motor from the power source. C. Secure all ventilation in the area. D. Preheat the insulation to assist in cleaning.

Last Answer : Answer: B

An increase in the amount of current flow through the armature of a shunt motor is the final result of a/an _____________. A. increase in the load on the motor B. decrease in the load on the motor C. increase in counter EMF D. decrease in armature torque

Description : An increase in the amount of current flow through the armature of a shunt motor is the final result of a/an _____________. A. increase in the load on the motor B. decrease in the load on the motor C. increase in counter EMF D. decrease in armature torque

Last Answer : Answer: A

An open armature connection in a DC propulsion motor could be caused by ____________. A. low-load operation B. clogged ventilation ducts C. sparking at the brushes D. a grounded shunt field coil

Description : An open armature connection in a DC propulsion motor could be caused by ____________. A. low-load operation B. clogged ventilation ducts C. sparking at the brushes D. a grounded shunt field coil

Last Answer : Answer: B

Regenerative braking (A) Can be used for stopping a motor. (B) Cannot be easily applied to DC series motors. (C) Can be easily applied to DC shunt motors (D) Cannot be used when motor load has overhauling characteristics.

Description : Regenerative braking (A) Can be used for stopping a motor. (B) Cannot be easily applied to DC series motors. (C) Can be easily applied to DC shunt motors (D) Cannot be used when motor load has overhauling characteristics.

Last Answer : Ans: B Because reversal of Ia would also mean reversal of field and hence of Eb

If an induction motor were to be operated at 90% rated voltage, _____________. A. there would be an increase in starting torque B. starting current would increase slightly C. synchronous speed would decrease slightly D. the slip would increase

Description : If an induction motor were to be operated at 90% rated voltage, _____________. A. there would be an increase in starting torque B. starting current would increase slightly C. synchronous speed would decrease slightly D. the slip would increase

Last Answer : Answer: D

Shunt, series, and compound wound motors, are all DC motors designed to operate from _____________. A. constant potential, variable current DC sources B. variable potential, constant current DC sources C. variable potential, variable current DC sources D. constant potential, constant current DC sources

Description : Shunt, series, and compound wound motors, are all DC motors designed to operate from _____________. A. constant potential, variable current DC sources B. variable potential, constant current DC ... C. variable potential, variable current DC sources D. constant potential, constant current DC sources

Last Answer : Answer: A

Why does the speed of a DC shunt motor decrease as the load increases?

Description : Why does the speed of a DC shunt motor decrease as the load increases?

Last Answer : Because if the load is increasing then the torque must also be increase. If not then the speed of motor will decrease.

With the increase in load on a d.c. shunt motor, speed of the motor

Description : With the increase in load on a d.c. shunt motor, speed of the motor (a) increases proportionately (b) remains constant (c) increase slightly (d) reduces slightly 

Last Answer : With the increase in load on a d.c. shunt motor, speed of the motor reduces slightly.

A 240 V, dc shunt motor draws 15 A while supplying the rated load at a speed of 80 rad/s.

Description : A 240 V, dc shunt motor draws 15 A while supplying the rated load at a speed of 80 rad/s. The armature resistance is 0.5 W and the field winding resistance is 80 W. The net Voltage across armature resistance at the time of plugging will be

Last Answer : A 240 V, dc shunt motor draws 15 A while supplying the rated load at a speed of 80 rad/s. The armature resistance is 0.5 W and the field winding resistance is 80 W. The net Voltage across armature resistance at the time of plugging will be 474 V

The no load speed of a d.c. shunt motor is 1140 rpm. At full load, the armature reaction weakens the main...

Description : The no load speed of a d.c. shunt motor is 1140 rpm. At full load, the armature reaction weakens the main flux by 5% whereas the armature circuit voltage drops by 10%. The motor full load speed in rpm will be: (A) 1080 (B) 1203 (C) 1000 (D) 1200

Last Answer : The no load speed of a d.c. shunt motor is 1140 rpm. At full load, the armature reaction weakens the main flux by 5% whereas the armature circuit voltage drops by 10%. The motor full load speed in rpm will be: 1080

If load on a d.c. shunt motor is increased, its speed is decreased due primarily to?

Description : If load on a d.c. shunt motor is increased, its speed is decreased due primarily to?

Last Answer : If load on a d.c. shunt motor is increased, its speed is decreased due primarily to decrease in back e.m.f.

As the load is increased the speed of D.C. shunt motor will?

Last Answer : As the load is increased the speed of D.C. shunt motor will reduce slightly.

The speed of a D.C. shunt motor more than its full-load speed can be obtained by?

Last Answer : The speed of a D.C. shunt motor more than its full-load speed can be obtained by decreasing the field current.

Why Speed Control of Induction Motor is difficult compared to DC shunt motor?

Description : Why Speed Control of Induction Motor is difficult compared to DC shunt motor?

Last Answer : Answer: Speed Control of DC shunt motor can be possible by providing resistance in the armature and field circuits and varying the resistors speed changes can be carried out over a wide range. ... employed. Care should be taken that in the process efficiency and power factor should be maintained.

Give two basic speed control scheme of DC shunt motor?

Description : Give two basic speed control scheme of DC shunt motor?

Last Answer : Answer: 1. By using flux control method: in this method a rheostat is connected across the field wdg to control the field current. So by changing the current the flux produced by the field wdg can ... ) can be varied, and since speed is directly proportional to Eb-IaRa the speed can be controlled.

The speed-torque characteristics of a DC series motor are approximately similar to those of the _________motor. (A) universal (B) synchronous (C) DC shunt (D) two-phase

Description : The speed-torque characteristics of a DC series motor are approximately similar to those of the _________motor. (A) universal (B) synchronous (C) DC shunt (D) two-phase

Last Answer : Ans: A Universal motor has same characteristics as DC series motor and also known as an a.c series motor.

A 4 pole lap wound dc shunt motor rotates at the speed of 1500 rpm, has a flux of 0.4 mWb and the total number of conductors are 1000. What is the value of emf? (A) 100 Volts. (B) 0.1 Volts. (C) 1 Volts. (D) 10 Volts.

Description : A 4 pole lap wound dc shunt motor rotates at the speed of 1500 rpm, has a flux of 0.4 mWb and the total number of conductors are 1000. What is the value of emf? (A) 100 Volts. (B) 0.1 Volts. (C) 1 Volts. (D) 10 Volts.

Last Answer : Ans: D Given N = 1500 rpm, Φ = 0.4 mWb, Z = 1000, P = 4, & A= 4 Therefore, Eb = NΦPZ / 60 A = 1500 x 0.4 x 4 x 1000 x 10^-3 / 60 x 4 = 60/6 = 10 volts

The full load torque of an electric motor is the __________. A. minimum torque developed by the motor accelerating from stop to full speed B. turning moment exerted by the motor at rated load and speed C. maximum torque developed by the motor with rated voltage and frequency D. turning moment exerted by the motor from any rotor angular position at any load

Description : The full load torque of an electric motor is the __________. A. minimum torque developed by the motor accelerating from stop to full speed B. turning moment exerted by the motor at rated load ... and frequency D. turning moment exerted by the motor from any rotor angular position at any load

Last Answer : Answer: B

If many turns of an alternating current coil for a contactor become short circuited, the coil _____________. A. will continue to operate B. will probably burn out immediately C. will operate on reduced current D. temperature will drop

Description : If many turns of an alternating current coil for a contactor become short circuited, the coil _____________. A. will continue to operate B. will probably burn out immediately C. will operate on reduced current D. temperature will drop

Last Answer : Answer: B

If many turns of an alternating current coil for a contactor become short circuited, the coil _____________. A. temperature will drop B. will probably burn out immediately C. will continue to operate D. will operate on reduced current

Description : If many turns of an alternating current coil for a contactor become short circuited, the coil _____________. A. temperature will drop B. will probably burn out immediately C. will continue to operate D. will operate on reduced current

Last Answer : Answer: B

If there is a reduction in the normally supplied frequency to a 120/240 volt, threephase AC current motor from 60 hertz to 55 hertz, the motor would _____________. A. run at a slower speed B. operate at a lower current C. overheat D. trip off the line

Description : If there is a reduction in the normally supplied frequency to a 120/240 volt, threephase AC current motor from 60 hertz to 55 hertz, the motor would _____________. A. run at a slower speed B. operate at a lower current C. overheat D. trip off the line

Last Answer : Answer: A

If a firm is operating at loss in the shortperiod in perfect combination, it should : (1) decrease the production and the price. (2) increase the production and the price (3) continue to operate as long as it covers even the variable costs. (4) shut-down and leave the industry

Description : If a firm is operating at loss in the shortperiod in perfect combination, it should : (1) decrease the production and the price. (2) increase the production and the price (3) continue to operate as long as it covers even the variable costs. (4) shut-down and leave the industry

Last Answer : (3) continue to operate as long as it covers even the variable costs. Explanation: The demand for labour is "derived- from the production and demand for the product being demanded. If the demand ... price and production numbers are met. Labour is "derived" from the market demand for the product.

When the price is less than the average variable cost, the firm should …………. (a) Continue to operate till the market recover ; (b) Shut down its operation for the time being (c) Retrench workers and pay them compensation; (d) Clear the existing stock at a price less than the prevailing price to beat the competitors

Description : When the price is less than the average variable cost, the firm should . (a) Continue to operate till the market recover ; (b) Shut down its operation for the time being (c) Retrench ... compensation; (d) Clear the existing stock at a price less than the prevailing price to beat the competitors

Last Answer :  (b) Shut down its operation for the time being

If a firm is operating at loss in the short-period in perfect combination, it should : (1) decrease the production and the price. (2) increase the production and the price (3) continue to operate as long as it covers even the variable costs. (4) shut-down and leave the industry

Description : If a firm is operating at loss in the short-period in perfect combination, it should : (1) decrease the production and the price. (2) increase the production and the price (3) continue to operate as long as it covers even the variable costs. (4) shut-down and leave the industry

Last Answer : continue to operate as long as it covers even the variable costs.

In case of a universal motor, torque pulsation is minimized by _________. (A) load inertia (B) rotor inertia (C) both rotor and load inertia (D) none of the above

Description : In case of a universal motor, torque pulsation is minimized by _________. (A) load inertia (B) rotor inertia (C) both rotor and load inertia (D) none of the above

Last Answer : Ans: C In a universal motor, torque pulsation is minimized by rotor and load inertia.

A single-phase induction motor will only start if you spin the rotor rapidly with the line switch closed. After starting, its speed fluctuates between very slow and half-speed. The problem probably lies in the ________. A. starting winding B. centrifugal mechanism C. centrifugal switch D. running winding

Description : A single-phase induction motor will only start if you spin the rotor rapidly with the line switch closed. After starting, its speed fluctuates between very slow and half-speed. The problem ... in the ________. A. starting winding B. centrifugal mechanism C. centrifugal switch D. running winding

Last Answer : Answer: D

A single-phase induction motor fails to start. The rotor is spun rapidly with the line switch closed. Having started by this method it is noted that the motor fluctuates between a very slow speed and half speed. The problem probably lies in the ______ A. starting winding B. centrifugal mechanism C. centrifugal switch D. running winding

Description : A single-phase induction motor fails to start. The rotor is spun rapidly with the line switch closed. Having started by this method it is noted that the motor fluctuates between a very slow ... lies in the ______ A. starting winding B. centrifugal mechanism C. centrifugal switch D. running winding

Last Answer : Answer: D

When starting a DC propulsion motor the variable rheostat must FIRST be turned ____________. A. all the way to the run position then quickly back to slow B. to the slow position then gradually moved to full speed C. to the mid position D. quickly to the run position

Description : When starting a DC propulsion motor the variable rheostat must FIRST be turned ____________. A. all the way to the run position then quickly back to slow B. to the slow position then gradually moved to full speed C. to the mid position D. quickly to the run position

Last Answer : Answer: B

The counter EMF of a DC motor is maximum when the _________. A. motor is at rated speed B. armature is not turning C. motor is almost up to rated speed D. armature has just begun to turn

Description : The counter EMF of a DC motor is maximum when the _________. A. motor is at rated speed B. armature is not turning C. motor is almost up to rated speed D. armature has just begun to turn

Last Answer : Answer: A

Why is it a good practice to have the frequency of the incoming alternator adjusted slightly higher than that of the loaded alternator when paralleling two alternators? A. This allows the oncoming machine to accept load immediately. B. This prevents the machine from floating on the line. C. The reverse power relay is prevented from activating. D. All of the above.

Description : Why is it a good practice to have the frequency of the incoming alternator adjusted slightly higher than that of the loaded alternator when paralleling two alternators? A. This allows the oncoming machine to ... line. C. The reverse power relay is prevented from activating. D. All of the above.

Last Answer : Answer: D

As load is added to an AC generator provided with constant field excitation, the prime mover slows down with the effect of ____________. A. lowering frequency and lowering generated voltage B. increasing frequency and increasing generated voltage C. increasing frequency and lowering generated voltage D. lowering frequency and increasing generated voltage

Description : As load is added to an AC generator provided with constant field excitation, the prime mover slows down with the effect of ____________. A. lowering frequency and lowering generated ... C. increasing frequency and lowering generated voltage D. lowering frequency and increasing generated voltage

Last Answer : Answer: A