Give three operating forces acting on indicating instruments.

Give three operating forces acting on indicating instruments.
by

1 Answer

Answer :

a. Deflecting force.

b. Controlling force.

c. Damping force.
by

Related questions

Electrostatic forces in high voltage circuits cause indicating instruments to give ____________. A. parallax readings B. highly intuitive readings C. highly accurate readings D. inaccurate readings

Description : Electrostatic forces in high voltage circuits cause indicating instruments to give ____________. A. parallax readings B. highly intuitive readings C. highly accurate readings D. inaccurate readings

Last Answer : Answer: D

A three-phase alternator is operating at 450 volts with the switchboard ammeter indicating 300 amps. The kw meter currently indicates 163.6 KW, with a power factor of 0.7. If the power factor increases to 0.8, the KW meter would then read ____________. A. 181.4 KW B. 186.8 KW C. 194.2 KW D. 201.4 KW

Description : A three-phase alternator is operating at 450 volts with the switchboard ammeter indicating 300 amps. The kw meter currently indicates 163.6 KW, with a power factor of 0.7. If the power factor increases to 0.8, the KW meter would then read ____________. A. 181.4 KW B. 186.8 KW C. 194.2 KW D. 201.4 KW

Last Answer : Answer: B

A three-phase alternator is operating at 450 volts with the switchboard ammeter indicating 300 amps. The kw meter currently indicates 163.6 KW, with a power factor of 0.7. If the power factor increases to 0.8, the KW meter reading would increase by ___ A. 17.8 KW B. 23.2 KW C. 30.6 KW D. 37.8 KW

Description : A three-phase alternator is operating at 450 volts with the switchboard ammeter indicating 300 amps. The kw meter currently indicates 163.6 KW, with a power factor of 0.7. If the power factor increases to 0.8, the KW meter reading would increase by ___ A. 17.8 KW B. 23.2 KW C. 30.6 KW D. 37.8 KW

Last Answer : Answer: B

The electrical device shown in the illustration is a/an _____________. EL-0077 A. operating coil B. indicating lamp C. motor armature D. potentiometer

Description : The electrical device shown in the illustration is a/an _____________. EL-0077 A. operating coil B. indicating lamp C. motor armature D. potentiometer

Last Answer : Answer: D

The force required to move the pointer in an indicating instruments is

Description : The force required to move the pointer in an indicating instruments is

Last Answer : The force required to move the pointer in an indicating instruments is deflecting force

What is the force acting on the pointer of an indicating instrument when it is in motion?

Description : What is the force acting on the pointer of an indicating instrument when it is in motion?

Last Answer : controlling, damping and deflecting torques

What are the operating principles of electrical measuring instruments?

Description : What are the operating principles of electrical measuring instruments?

Last Answer : a. Magnetic effect. b. Electro dynamic effect. c. Electro magnetic effect. d. Thermal effect. e. Chemical effect. f. Electro static effect.

In the illustrated ground detection system with a ground on phase A, if the switch is opened __________. EL-0009 A. lamp A will dim or go out depending on the severity of the ground B. all three lamps will return to their normal brightness indicating that the bulbs are not burnt out C. lamps B and C will dim lamp A will be brighter D. lamp A will start flickering if the ground is in an AC induction motor

Description : In the illustrated ground detection system with a ground on phase A, if the switch is opened __________. EL-0009 A. lamp A will dim or go out depending on the severity of the ground B. all three ... lamp A will be brighter D. lamp A will start flickering if the ground is in an AC induction motor

Last Answer : Answer: B

The statement ---- if three forces acting at a point are in equilibrium, each force is proportional to the sine of the angle between the other two ---- is known as a.Law of polygon of forces b.D'Alembert's principle c.Newtons law of forces d.Lami's theorem e.Law of triangle of forces

Description : The statement ---- if three forces acting at a point are in equilibrium, each force is proportional to the sine of the angle between the other two ---- is known as a.Law of polygon of forces b.D'Alembert's principle c.Newtons law of forces d.Lami's theorem e.Law of triangle of forces

Last Answer : d. Lami's theorem

Three forces A, B and C of magnitudes 8 N, 12 N and 20 N acting on a particle are in equilibrim. It can be concluded that a.107 dynes b.B and C act in opposite directions c.one of the forces in non-coplaner d.A and B act at 90? e.one of the forces is non-concurrent

Description : Three forces A, B and C of magnitudes 8 N, 12 N and 20 N acting on a particle are in equilibrim. It can be concluded that a.107 dynes b.B and C act in opposite directions c.one of the forces in non-coplaner d.A and B act at 90? e.one of the forces is non-concurrent

Last Answer : b. B and C act in opposite directions

According to law of triangle of forces (A) Three forces acting at a point will be in equilibrium (B) Three forces acting at a point can be represented by a triangle, each side being proportional to force (C) If three forces acting upon a particle are represented in magnitude and direction by the sides of a triangle, taken in order, they will be in equilibrium (D) If three forces acting at a point are in equilibrium, each force is proportional to the sine of the angle between the other two

Description : According to law of triangle of forces  (A) Three forces acting at a point will be in equilibrium  (B) Three forces acting at a point can be represented by a triangle, each side ... point are in equilibrium, each force is proportional to the sine of  the angle between the other two 

Last Answer : (C) If three forces acting upon a particle are represented in magnitude and direction by the  sides of a triangle, taken in order, they will be in equilibrium

If three forces acting in different planes can be represented by a triangle, these will be in (A) Non-equilibrium (B) Partial equilibrium (C) Full equilibrium (D) None of the above

Description : If three forces acting in different planes can be represented by a triangle, these will be in  (A) Non-equilibrium  (B) Partial equilibrium  (C) Full equilibrium  (D) None of the above 

Last Answer : (A) Non-equilibrium 

If three forces acting in one plane upon a rigid body, keep it in equilibrium, then they must either (A) Meet in a point (B) Be all parallel (C) At least two of them must meet (D) All the above are correct

Description : If three forces acting in one plane upon a rigid body, keep it in equilibrium, then they must either (A) Meet in a point (B) Be all parallel (C) At least two of them must meet (D) All the above are correct

Last Answer : (D) All the above are correct

According to Lami's theorem (A) Three forces acting at a point will be in equilibrium (B) Three forces acting at a point can be represented by a triangle, each side being proportional to force (C) If three forces acting upon a particle are represented in magnitude and direction by the sides of a triangle, taken in order, they will be in equilibrium (D) If three forces acting at a point are in equilibrium, each force is proportional to the sine of the angle between the other two

Description : According to Lami's theorem (A) Three forces acting at a point will be in equilibrium (B) Three forces acting at a point can be represented by a triangle, each side being proportional to ... point are in equilibrium, each force is proportional to the sine of the angle between the other two

Last Answer : Answer: Option D

Coast Guard Regulations (46 CFR), require that an indicating light at the propulsion control station will operate if overloading or overheating occurs in a _______________. A. forced draft blower motor B. steering gear motor C. fuel pump motor D. condensate pump motor

Description : Coast Guard Regulations (46 CFR), require that an indicating light at the propulsion control station will operate if overloading or overheating occurs in a _______________. A. forced draft blower motor B. steering gear motor C. fuel pump motor D. condensate pump motor

Last Answer : Answer: B

Which of the following statements is true concerning the motor controller diagram shown in the illustration? EL-0023 A. Terminal 'T2' is hot only on high speed. B. Both indicating lights will be lit on both high and low speeds as they are connected to the common lead when the motor is running. C. Overload protection is provided for high speed operation only. D. 'L2' is always connected to 'T2' whenever the motor is running.

Description : Which of the following statements is true concerning the motor controller diagram shown in the illustration? EL-0023 A. Terminal 'T2' is hot only on high speed. B. Both indicating lights will be lit on ... high speed operation only. D. 'L2' is always connected to 'T2' whenever the motor is running.

Last Answer : Answer: D

An overload in which of the listed motors will result in the illumination of an indicating light at the propulsion control station alarm panel? A. Fuel pump motor B. Steering motor C. Condensate pump motor D. Forced draft blower motor

Description : An overload in which of the listed motors will result in the illumination of an indicating light at the propulsion control station alarm panel? A. Fuel pump motor B. Steering motor C. Condensate pump motor D. Forced draft blower motor

Last Answer : Answer: B

In the illustrated 450 VAC system, what should be provided between the bus and the device labeled 'F'? EL-0003 A. a potential transformer B. a current transformer C. an emergency disconnect device D. an audible alarm and indicating light

Description : In the illustrated 450 VAC system, what should be provided between the bus and the device labeled 'F'? EL-0003 A. a potential transformer B. a current transformer C. an emergency disconnect device D. an audible alarm and indicating light

Last Answer : Answer: A

Which of the following statements regarding the use of a current measuring instrument is correct? A. It must be connected in series with the circuit. B. You should always start with the lowest range until a suitable reading is obtained. C. The indicating needle is deflected from left to right regardless of polarity. D. An external shunt is generally utilized where current is less than 10 amperes.

Description : Which of the following statements regarding the use of a current measuring instrument is correct? A. It must be connected in series with the circuit. B. You should always start with the lowest range ... of polarity. D. An external shunt is generally utilized where current is less than 10 amperes.

Last Answer : Answer: A

The 'dielectric constant' is a numerical value indicating the effectiveness of a dielectric material in comparison to that of a standard, which is _______________. A. paper or cloth B. glass or mica C. plastic or Teflon D. dry air or a vacuum

Description : The 'dielectric constant' is a numerical value indicating the effectiveness of a dielectric material in comparison to that of a standard, which is _______________. A. paper or cloth B. glass or mica C. plastic or Teflon D. dry air or a vacuum

Last Answer : Answer: D

In the illustration, 'D' is the symbol for a/an __________. EL-0005 A. thermal overload heater B. portable cable C. fuse D. indicating lamp

Description : In the illustration, 'D' is the symbol for a/an __________. EL-0005 A. thermal overload heater B. portable cable C. fuse D. indicating lamp

Last Answer : Answer: C

The leads from a megohmmeter are attached to the leads of an AC motor field coil. A reading of infinity is obtained indicating a/an ____________. A. open field coil B. shorted field coil C. grounded field coil D. shunted field coil

Description : The leads from a megohmmeter are attached to the leads of an AC motor field coil. A reading of infinity is obtained indicating a/an ____________. A. open field coil B. shorted field coil C. grounded field coil D. shunted field coil

Last Answer : Answer: A

A faulty 'function generator' shown in the illustration may prevent _____________. EL-0095 A. proper pitch control from both the 'bridge' and 'engine room thrust levers' B. the 'split potentiometer's' ability to control pitch C. the pitch meter from indicating accurately D. relays #2 and/or #3 from energizing

Description : A faulty 'function generator' shown in the illustration may prevent _____________. EL-0095 A. proper pitch control from both the 'bridge' and 'engine room thrust levers' B. the 'split potentiometer ... control pitch C. the pitch meter from indicating accurately D. relays #2 and/or #3 from energizing

Last Answer : Answer: A

When a console indicating lamp burns out, attempts to renew it should not be made while maneuvering because _______________. A. the new lamp may be of a higher wattage and cause heat damage to the lens B. removing a faulty lamp usually causes an alarm to sound on the bridge C. attention should be paid only to engine orders D. a socket/wiring fault may cause a ground or short circuit to shut down a vital function

Description : When a console indicating lamp burns out, attempts to renew it should not be made while maneuvering because _______________. A. the new lamp may be of a higher wattage and cause heat damage to the lens ... D. a socket/wiring fault may cause a ground or short circuit to shut down a vital function

Last Answer : Answer: D

The meter indicating the position of the 'bridge Thrust lever' shown in the illustration is located ___________________. EL-0095 A. in the Engine Control Room B. on the Bridge C. in the Captain's office D. in the Chief Engineer's office

Description : The meter indicating the position of the 'bridge Thrust lever' shown in the illustration is located ___________________. EL-0095 A. in the Engine Control Room B. on the Bridge C. in the Captain's office D. in the Chief Engineer's office

Last Answer : Answer: A

Prior to using an analog type ohmmeter, the leads are purposely shorted together. Which of the following actions should be taken if, when adjusting to 'zero' ohms, the indicating needle can not be returned to 'zero' on the scale? A. The lead clips should be replaced. B. The batteries should be replaced. C. The test reading should be added to each final reading. D. The test reading should be subtracted from each final reading.

Description : Prior to using an analog type ohmmeter, the leads are purposely shorted together. Which of the following actions should be taken if, when adjusting to 'zero' ohms, the indicating needle can not be ... be added to each final reading. D. The test reading should be subtracted from each final reading.

Last Answer : Answer: B

What are the essentials of indicating instrument?

Description : What are the essentials of indicating instrument?

Last Answer : a. Deflecting torque or force (effect of electricity). b. Controlling torque or force (spring control and gravity control). c. Damping torque or force (air friction, eddy current and fluid friction).

Which instruments are used for perceiving and acting upon the environment? a) Sensors and Actuators b) Sensors c) Perceiver d) None of the mentioned

Description : Which instruments are used for perceiving and acting upon the environment? a) Sensors and Actuators b) Sensors c) Perceiver d) None of the mentioned

Last Answer : a) Sensors and Actuators

Which of the following forces does not act on the moving systems of analog instruments?

Description : Which of the following forces does not act on the moving systems of analog instruments?

Last Answer : an electrostatic force

Why we are using only 50 Hz for single and three phase electrical instruments?

Description : Why we are using only 50 Hz for single and three phase electrical instruments?

Last Answer : Synchronization condition: There are five conditions that must be met before the synchronization process takes place. The alternator must have equal line voltage, frequency, phase sequence, phase angle and waveform to that ... in the US and North America and 50 Hz in most of the rest of the world.

What are three types of secondary instruments?

Description : What are three types of secondary instruments?  

Last Answer : The three types of secondary instruments are, a. Indicating type: It only indicates the electrical quantity measured. Example: Ammeter, Voltmeter, Frequency meter etc. b. Integrating type: It ... as well as indicates the electrical quantity being measured. Example: 3 pen graphical recorder. 

Can the sentence “The analysis of the soils forces acting on...” be revised as “The analysis of the soils forces acting on..”?

Description : Can the sentence “The analysis of the soils forces acting on...” be revised as “The analysis of the soils forces acting on..”?

Last Answer : answer:The analysis must be simplified to obtain Both of the other ones sound a bit awkward to me, the second one moreso than the first. Making simplifications is something that you, the scientist, are ... me. Mostly because made is not really a verb that makes sense for an analysis, I think.

The necessary condition for the forces acting on a body to be in equilibrium is that these should be a.In the same direction b.Coplaner c.Similar in nature d.Should not meet at a point e.(B) and (D) above

Description : The necessary condition for the forces acting on a body to be in equilibrium is that these should be a.In the same direction b.Coplaner c.Similar in nature d.Should not meet at a point e.(B) and (D) above

Last Answer : e. (B) and (D) above

The statement --- if forces acting on a point can be represented in magnitude and direction by the sides of a polygon taken in order then their resultant will be represented in magnitude and direction by the closing side of the polygon taken in opposite order ---- is known as a.Law of triangle of forces b.Newton's law of forces c.Law of polygon of forces d.D'Alembert's rule e.Lami's theorem

Description : The statement --- if forces acting on a point can be represented in magnitude and direction by the sides of a polygon taken in order then their resultant will be represented in magnitude and direction by the closing ... 's law of forces c.Law of polygon of forces d.D'Alembert's rule e.Lami's theorem

Last Answer : c. Law of polygon of forces

When two forces acting at a point are such that if the direction of one is reversed, the direction of the resultant is turned through a right angle, the forces must be a.inclined at more than 90? b.inclined at less than 90? c.equal in magnitude d.acting at 180? e.107 dynes

Description : When two forces acting at a point are such that if the direction of one is reversed, the direction of the resultant is turned through a right angle, the forces must be a.inclined at more than 90? b.inclined at less than 90? c.equal in magnitude d.acting at 180? e.107 dynes

Last Answer : c. equal in magnitude

The statement the resultant of the external forces applied to a body (rigid or non-rigid) composed of a system of particles is equivalent to the vector summation of the effective forces acting on all particles-is known as a.Corollary to Newton's laws of motion b.Principle of dynamics c.D' Alembert's principle d.Nowton's law e.Mohr's principle

Description : The statement the resultant of the external forces applied to a body (rigid or non-rigid) composed of a system of particles is equivalent to the vector summation of the effective forces acting on all ... motion b.Principle of dynamics c.D' Alembert's principle d.Nowton's law e.Mohr's principle

Last Answer : c. D' Alembert's principle

A number of forces acting at a point will be in equilibrium if a.Sum of the forces is zero b.Algebraic sum of the forces is zero c.Sum of the resolved parts in any two perpendicular directions are both zero d.None of the above e.The metacentre of the body

Description : A number of forces acting at a point will be in equilibrium if a.Sum of the forces is zero b.Algebraic sum of the forces is zero c.Sum of the resolved parts in any two perpendicular directions are both zero d.None of the above e.The metacentre of the body

Last Answer : d. None of the above

When all the forces acting on a body lie in one plane and their lines of action meet at one point, the forces a.constitute a moment b.constitute a couple c.are known as coplaner-concurrent forces. d.are known as non-coplaner forces e.107 dynes

Description : When all the forces acting on a body lie in one plane and their lines of action meet at one point, the forces a.constitute a moment b.constitute a couple c.are known as coplaner-concurrent forces. d.are known as non-coplaner forces e.107 dynes

Last Answer : c. are known as coplaner-concurrent forces.

A locomotive of weight 100 tonnes is attached to train of wagons weighing 1000 tonnes. The locomotive pulls the wagons with a constant velocity of 36 km/hour. When the coupling between the train and wagons breaks, the wagons roll on 95 m in 10 sec. The distance between the locomotive and the wagons at this instant assuming that the forces acting on the train are unaltered would be a.0.36 m b.0.44 m c.0.77 m. d.0.5 m e.0.66 m

Description : A locomotive of weight 100 tonnes is attached to train of wagons weighing 1000 tonnes. The locomotive pulls the wagons with a constant velocity of 36 km/hour. When the coupling between the train and wagons breaks, the wagons roll on 95 m in ... would be a.0.36 m b.0.44 m c.0.77 m. d.0.5 m e.0.66 m

Last Answer : d. 0.5 m

Assertion Path of a charged particle in uniform magnetic field cannot be a parabola, if no other forces (other than magnetic force) are acting on the

Description : Assertion Path of a charged particle in uniform magnetic field cannot be a parabola, if no other forces (other than magnetic force) are acting on the

Last Answer : Assertion Path of a charged particle in uniform magnetic field cannot be a parabola, if no other ... . If Assertion is false but Reason is true.

The resultant of two forces 10 N and 15 N acting along + x and – x-axes respectively, is

Description : The resultant of two forces 10 N and 15 N acting along + x and – x-axes respectively, is

Last Answer : The resultant of two forces 10 N and 15 N acting along + x and - x-axes respectively, is (A) 25 N along ... along + x-axis (D) 5 N along - x-axis

What combination of all the forces acting on an object is?

Description : What combination of all the forces acting on an object is?

Last Answer : that is called the net force; it is a vector sum of all theforces acting on it

When equal forces are acting on one object in opposite directions are called?

Description : When equal forces are acting on one object in opposite directions are called?

Last Answer : Neutral or in equilibrium

What force or forces are acting on the falling climber in picture?

Description : What force or forces are acting on the falling climber in picture?

Last Answer : What is the answer ?

Why do the magnetic forces acting on the coil change as the current running through the coil changes?

Description : Why do the magnetic forces acting on the coil change as the current running through the coil changes?

Last Answer : What is the answer ?

What are the two forces acting on a hot air ballon that is floating?

Description : What are the two forces acting on a hot air ballon that is floating?

Last Answer : What is the answer ?