Electrostatic forces in high voltage circuits cause indicating instruments to give ____________. A. parallax readings B. highly intuitive readings C. highly accurate readings D. inaccurate readings

Electrostatic forces in high voltage circuits cause indicating instruments to give ____________. A. parallax readings B. highly intuitive readings C. highly accurate readings D. inaccurate readings
by

1 Answer

Answer :

Answer: D
by

Related questions

When you check the specific gravity of the battery electrolyte with a hydrometer, it should be kept in mind that ____________. A. the battery is fully charged when the indicator floats low in the electrolyte B. any water that has been previously added to the cells will dilute the solution and give a false reading C. a hydrometer reading is inaccurate if taken immediately after water is added to the cell D. temperature has no effect on hydrometer readings

Description : When you check the specific gravity of the battery electrolyte with a hydrometer, it should be kept in mind that ____________. A. the battery is fully charged when the indicator floats low in ... taken immediately after water is added to the cell D. temperature has no effect on hydrometer readings

Last Answer : Answer: C

Give three operating forces acting on indicating instruments.

Description : Give three operating forces acting on indicating instruments.

Last Answer : a. Deflecting force. b. Controlling force. c. Damping force.

Which one of the following statements is not correc t? (a) Parallax error is eliminated when there is no change in the staff reading when eye is moved up and down (b) The objective lens is to be focused towards a white or bright background for clear visibility of cross-hairs (c) Temporary adjustments of the dumpy level are to be performed at every set up (d) The eyepiece need not be adjusted after the first set up when the same surveyor is taking readings

Description : Which one of the following statements is not correc t? (a) Parallax error is eliminated when there is no change in the staff reading when eye is moved up and down (b) The objective lens is ... (d) The eyepiece need not be adjusted after the first set up when the same surveyor is taking readings

Last Answer : (b) The objective lens is to be focused towards a white or bright background for clear visibility of cross-hairs

In which of the situations listed will a megohmmeter give the most accurate readings? A. While the machine is in operation. B. While the machine is discharging static electricity. C. Immediately prior to restarting the machine. D. When the machine has been shut down and grounded for a period of 15 minutes.

Description : In which of the situations listed will a megohmmeter give the most accurate readings? A. While the machine is in operation. B. While the machine is discharging static electricity. C. Immediately prior to ... machine. D. When the machine has been shut down and grounded for a period of 15 minutes.

Last Answer : Answer: D

Electrostatic type instruments are mainly used for measurement of: a) Heavy currents b) Low currents c) Low voltages d) High voltages

Description : Electrostatic type instruments are mainly used for measurement of: a) Heavy currents b) Low currents c) Low voltages d) High voltages

Last Answer : Ans: D

In preparing to take insulation resistance readings on a main generator, the windings should be grounded for about 15 minutes prior to the test to _____________. A. allow accurate zeroing of the meter B. help the windings to cool to ambient temperature C. release any residual capacitive charge from the windings D. help the windings to cool to the same temperature as the ground test connection

Description : In preparing to take insulation resistance readings on a main generator, the windings should be grounded for about 15 minutes prior to the test to _____________. A. allow accurate zeroing of the meter ... the windings D. help the windings to cool to the same temperature as the ground test connection

Last Answer : Answer: C

A three-phase alternator is operating at 450 volts with the switchboard ammeter indicating 300 amps. The kw meter currently indicates 163.6 KW, with a power factor of 0.7. If the power factor increases to 0.8, the KW meter would then read ____________. A. 181.4 KW B. 186.8 KW C. 194.2 KW D. 201.4 KW

Description : A three-phase alternator is operating at 450 volts with the switchboard ammeter indicating 300 amps. The kw meter currently indicates 163.6 KW, with a power factor of 0.7. If the power factor increases to 0.8, the KW meter would then read ____________. A. 181.4 KW B. 186.8 KW C. 194.2 KW D. 201.4 KW

Last Answer : Answer: B

The leads from a megohmmeter are attached to the leads of an AC motor field coil. A reading of infinity is obtained indicating a/an ____________. A. open field coil B. shorted field coil C. grounded field coil D. shunted field coil

Description : The leads from a megohmmeter are attached to the leads of an AC motor field coil. A reading of infinity is obtained indicating a/an ____________. A. open field coil B. shorted field coil C. grounded field coil D. shunted field coil

Last Answer : Answer: A

Operational amplifiers, used primarily in analog circuits, are characterized by ____________. A. high input impedance, high gain and low output impedance B. high input impedance, high gain and high output impedance C. low input impedance, low gain and high output impedance D. low input impedance, high gain and low output impedance

Description : Operational amplifiers, used primarily in analog circuits, are characterized by ____________. A. high input impedance, high gain and low output impedance B. high input impedance, high gain and high output ... gain and high output impedance D. low input impedance, high gain and low output impedance

Last Answer : Answer: A

The purpose of a short circuit forcing module (short time trip) installed in a branch line is to provide ____________. A. high speed clearance of low impedance short circuits in the branch B. continuity of service on main bus under short circuit conditions in a branch C. isolation of short circuits by selective tripping of branch circuit breakers D. all of the above

Description : The purpose of a short circuit forcing module (short time trip) installed in a branch line is to provide ____________. A. high speed clearance of low impedance short circuits in the branch B. ... C. isolation of short circuits by selective tripping of branch circuit breakers D. all of the above

Last Answer : Answer: D

A low voltage source is being used for testing armature coils. A coil short circuit will be indicated by a _______. A. high voltage reading, while the other coil readings will have an equal or lower value B. low or zero voltage reading, while the other coils will have higher readings C. fluctuating voltmeter reading, while the other coil readings are steady D. steady voltmeter reading, while the other coil readings are fluctuating

Description : A low voltage source is being used for testing armature coils. A coil short circuit will be indicated by a _______. A. high voltage reading, while the other coil readings will have an ... the other coil readings are steady D. steady voltmeter reading, while the other coil readings are fluctuating

Last Answer : Answer: B

When troubleshooting electronic equipment, you should use a high impedance multimeter ________________. A. to prevent excess current flow through the meter that would damage it B. for AC measurements only and a low resistance meter for DC measurements C. whenever a low impedance meter is not available, regardless of the components being tested D. so as not to load down the circuit and obtain erroneous voltage readings

Description : When troubleshooting electronic equipment, you should use a high impedance multimeter ________________. A. to prevent excess current flow through the meter that would damage it B. for AC measurements only ... being tested D. so as not to load down the circuit and obtain erroneous voltage readings

Last Answer : Answer: D

When shipboard electrical distribution circuits are connected in parallel, additional parallel circuits will cause the total circuit resistance to _____________. A. increase, causing a drop in the line current B. increase, causing a decrease in the line voltage C. decrease, causing an increase in the line voltage D. decrease, causing an increase in the line current

Description : When shipboard electrical distribution circuits are connected in parallel, additional parallel circuits will cause the total circuit resistance to _____________. A. increase, causing a drop in the line current B ... an increase in the line voltage D. decrease, causing an increase in the line current

Last Answer : Answer: D

The force required to move the pointer in an indicating instruments is

Description : The force required to move the pointer in an indicating instruments is

Last Answer : The force required to move the pointer in an indicating instruments is deflecting force

The power requirements for operating the circuits shown in the illustration are ____________. EL-0099 A. (+) and (-) 50 volts D.C. B. (+) 28 and (+) 50 volts D.C. C. (+) 28 volts D.C. and 115 volts A.C. D. (+) 28 volts and (-) 50 volts D.C.

Description : The power requirements for operating the circuits shown in the illustration are ____________. EL-0099 A. (+) and (-) 50 volts D.C. B. (+) 28 and (+) 50 volts D.C. C. (+) 28 volts D.C. and 115 volts A.C. D. (+) 28 volts and (-) 50 volts D.C.

Last Answer : Answer: A

A molded-case breaker provides protection against short circuits by using a/an ____________. A. shading coil B. arc quencher C. electromagnet D. holding coil

Description : A molded-case breaker provides protection against short circuits by using a/an ____________. A. shading coil B. arc quencher C. electromagnet D. holding coil

Last Answer : Answer: C

Indicating instrument is assumed to be most accurate at what part of the scale?

Description : Indicating instrument is assumed to be most accurate at what part of the scale?

Last Answer : at half or full

If a voltage tester is being used to check for defective fuses in the circuit, shown in the illustration, which of the readings will indicate that fuse #2 is open? EL-0062 A. C-B full voltage B. A-D full voltage C. A-D no voltage D. C-B no voltage

Description : If a voltage tester is being used to check for defective fuses in the circuit, shown in the illustration, which of the readings will indicate that fuse #2 is open? EL-0062 A. C-B full voltage B. A-D full voltage C. A-D no voltage D. C-B no voltage

Last Answer : Answer: C

As a general rule, the first troubleshooting action to be taken in checking faulty electric control devices is to _____________. A. draw a one line diagram of the circuitry B. test all fuses and measure the line voltage C. take megger readings D. insulate the apparatus from ground

Description : As a general rule, the first troubleshooting action to be taken in checking faulty electric control devices is to _____________. A. draw a one line diagram of the circuitry B. test all fuses and measure the line voltage C. take megger readings D. insulate the apparatus from ground

Last Answer : Answer: B

When a console indicating lamp burns out, attempts to renew it should not be made while maneuvering because _______________. A. the new lamp may be of a higher wattage and cause heat damage to the lens B. removing a faulty lamp usually causes an alarm to sound on the bridge C. attention should be paid only to engine orders D. a socket/wiring fault may cause a ground or short circuit to shut down a vital function

Description : When a console indicating lamp burns out, attempts to renew it should not be made while maneuvering because _______________. A. the new lamp may be of a higher wattage and cause heat damage to the lens ... D. a socket/wiring fault may cause a ground or short circuit to shut down a vital function

Last Answer : Answer: D

On all instruments like measuring cylinder, pipette and burette, readings are always taken at the bottom of the meniscus of liquid. This is not true for liquids like A. Oil B. Ink C. Mercury D. Seawater

Description : On all instruments like measuring cylinder, pipette and burette, readings are always taken at the bottom of the meniscus of liquid. This is not true for liquids like A. Oil B. Ink C. Mercury D. Seawater

Last Answer : Mercury

In optical reading instruments (A) The vertical circle is usually continuous from 0° to 359° (B) The readings increase when the telescope is elevated in the face left position (C) The readings decrease when the telescope is elevated in the face right position (D) All the above

Description : In optical reading instruments (A) The vertical circle is usually continuous from 0° to 359° (B) The readings increase when the telescope is elevated in the face left position (C) The readings decrease when the telescope is elevated in the face right position (D) All the above

Last Answer : (D) All the above

When troubleshooting an alkaline storage battery a weak or dead cell is best located by ____________. A. checking the specific gravity of each cell B. visually inspecting each cell's electrolyte level C. testing each cell with a voltmeter D. measuring the electrolyte temperature with an accurate mercury thermometer

Description : When troubleshooting an alkaline storage battery a weak or dead cell is best located by ____________. A. checking the specific gravity of each cell B. visually inspecting each cell's ... testing each cell with a voltmeter D. measuring the electrolyte temperature with an accurate mercury thermometer

Last Answer : Answer: C

Routine maintenance of dry-type transformers should include ____________. A. cleaning the windings, if accessible, with a vacuum cleaner or very low pressure air B. measuring and recording the winding temperature with an accurate mercury thermometer C. periodic cleaning of the winding insulation with an approved solvent D. making sure that the units are close to bulkheads or corners to protect them from damage

Description : Routine maintenance of dry-type transformers should include ____________. A. cleaning the windings, if accessible, with a vacuum cleaner or very low pressure air B. measuring and recording the winding ... . making sure that the units are close to bulkheads or corners to protect them from damage

Last Answer : Answer: A

Are psychic readings accurate?

Description : Are psychic readings accurate?

Last Answer : No, most psychics are in the business just for money. They could say anything and make you believe it. No one knows the future, and it'd be better to just live life on your own than letting a psychic make you worry.

Which of the following statements concerning monitoring techniques in the intensive care unit are true? A. Pulmonary artery and pulmonary capillary wedge pressure readings should be made at end inspiration, to minimize ventilatory artifacts. B. Continuous SvO 2 monitoring based on the technique of reflectance spectrophotometry has been shown to be accurate and reliable. C. Direct measurement of gastric intramucosal pH can be provided by gastrointestinal tonometry. D. Hyperlactatemia may be seen in a number of clinical conditions not associated with tissue hypoxia, including liver disease and hypermetabolic states.

Description : Which of the following statements concerning monitoring techniques in the intensive care unit are true? A. Pulmonary artery and pulmonary capillary wedge pressure readings should be made ... clinical conditions not associated with tissue hypoxia, including liver disease and hypermetabolic states.

Last Answer : Answer: BD DISCUSSION: Many different monitoring techniques may be used to assess the adequacy of therapy for shock. The pulmonary artery catheter can provide important hemodynamic and oxygen ... also be seen with liver disease, toxin ingestion, and hypermetabolic states not associated with shock

When taking resistance readings with a VOM, you will obtain the most accurate readings at or near what part of the scale?

Description : When taking resistance readings with a VOM, you will obtain the most accurate readings at or near what part of the scale?

Last Answer : Midscale.

At what point on a meter movement are the most accurate readings taken?

Description : At what point on a meter movement are the most accurate readings taken?

Last Answer : Midscale.

If a synchronous motor begins to vibrate severely and pull out of synchronism, the cause may be ____________. A. an overload B. an open in the field coils C. no exciter voltage D. all of the above

Description : If a synchronous motor begins to vibrate severely and pull out of synchronism, the cause may be ____________. A. an overload B. an open in the field coils C. no exciter voltage D. all of the above

Last Answer : Answer: D

Increasing the load to the secondary windings of a transformer will cause a/an ____________. A. decrease in the primary voltage B. increase in the primary voltage C. decrease in the primary current D. increase in the primary current

Description : Increasing the load to the secondary windings of a transformer will cause a/an ____________. A. decrease in the primary voltage B. increase in the primary voltage C. decrease in the primary current D. increase in the primary current

Last Answer : Answer: D

Electrostatic instruments are exclusively used as

Description : Electrostatic instruments are exclusively used as

Last Answer : voltmeters

Electrostatic instruments are exclusively used as

Description : Electrostatic instruments are exclusively used as

Last Answer : voltmeters

Electrostatic type instruments are primarily used as

Description : Electrostatic type instruments are primarily used as 

Last Answer : Voltmeter

Electrostatic instruments are normally used for

Last Answer :  Electrostatic instruments are normally used for High voltage measurements.

The electrostatic instruments can be used without serious loss of accuracy upto ......... frequency

Last Answer : The electrostatic instruments can be used without serious loss of accuracy upto 100kHz frequency.

Which of the listed types of lighting circuits does the diagram shown in the illustration represent? EL-0081 A. High pressure sodium B. Low voltage quartz C. Mercury vapor D. Standard fluorescent

Description : Which of the listed types of lighting circuits does the diagram shown in the illustration represent? EL-0081 A. High pressure sodium B. Low voltage quartz C. Mercury vapor D. Standard fluorescent

Last Answer : Answer: D

High sensitive DC voltmeter provides accurate reading when measuring ___ circuits.

Description : High sensitive DC voltmeter provides accurate reading when measuring ___ circuits.

Last Answer : high resistance

High sensitive DC voltmeter provides accurate reading when measuring ___ circuits.

Description : High sensitive DC voltmeter provides accurate reading when measuring ___ circuits.

Last Answer : high resistance

Is citing "human nature" as a cause of a particular human behavior, inaccurate?

Description : Is citing "human nature" as a cause of a particular human behavior, inaccurate?

Last Answer : It's mostly an excuse, but certain things are typically associated with human nature. It would be up to knowledgable parties to decide whether it applies to the specific situation or ... humans are selfish, highly sexual, opportunistic, and needy beings who crave constant attention and agreement.

When you are measuring a component using a bridge, what is the most common cause of inaccurate measurements?

Description : When you are measuring a component using a bridge, what is the most common cause of inaccurate measurements?

Last Answer : The capacitive and inductive characteristics of the test leads.

The weakest of all fundamental forces is – (1) Gravitational force (2) Electrostatic force (3) Magnetic force (4) Nuclear force

Description : The weakest of all fundamental forces is – (1) Gravitational force (2) Electrostatic force (3) Magnetic force (4) Nuclear force

Last Answer : (1) Gravitational force Explanation: In particle physics, fundamental interactions (sometimes called interactive forces or fundamental forces) are the ways that elementary particles interact with one another. ... weak interaction ("weak nuclear force"), and gravitation. All are non-contact forces.

Which of the following forces is nonconservative? w) gravitational force x) electrostatic force y) sliding frictional force z) restorative force of a spring

Description : Which of the following forces is nonconservative? w) gravitational force x) electrostatic force y) sliding frictional force z) restorative force of a spring

Last Answer : ANSWER: Y -- SLIDING FRICTIONAL FORCE