In recovery from a spin: a. Ailerons should be kept neutral b. Airspeed increases c. Ailerons used to stop the spin d. Rudder and ailerons used against the direction of spin direction

In recovery from a spin:  
a. Ailerons should be kept neutral  
b. Airspeed increases  
c. Ailerons used to stop the spin  
d. Rudder and ailerons used against the direction of spin direction
by

1 Answer

Answer :

a. Ailerons should be kept neutral
by

Related questions

The control surface which gives longitudinal control is: a. The rudder b. The ailerons c. The elevators d. The flaps

Description : The control surface which gives longitudinal control is: a. The rudder b. The ailerons c. The elevators d. The flaps

Last Answer : c. The elevators

Which of the following increases the stall angle? a. Slats b. Flaps c. Spoilers d. Ailerons

Description : Which of the following increases the stall angle? a. Slats b. Flaps c. Spoilers d. Ailerons

Last Answer : a. Slats

A yaw damper: a. Increases rudder effectiveness b. Must be disengaged before making a turn c. Augments stability d. Increases the rate of yaw

Description : A yaw damper: a. Increases rudder effectiveness b. Must be disengaged before making a turn c. Augments stability d. Increases the rate of yaw

Last Answer : c. Augments stability

Lowering the flaps during a landing approach: a. Increases the angle of descent without increasing the airspeed b. Decreases the angle of descent without increasing power c. Eliminates floating d. Permits approaches at a higher indicated airspeed

Description : Lowering the flaps during a landing approach: a. Increases the angle of descent without increasing the airspeed b. Decreases the angle of descent without increasing power c. Eliminates floating d. Permits approaches at a higher indicated airspeed

Last Answer : a. Increases the angle of descent without increasing the airspeed

To recover from a spin, the elevators should be: a. Moved up to increase the angle of attack b. Moved down to reduce the angle of attack c. Set to neutral d. Allowed to float

Description : To recover from a spin, the elevators should be: a. Moved up to increase the angle of attack b. Moved down to reduce the angle of attack c. Set to neutral d. Allowed to float

Last Answer : b. Moved down to reduce the angle of attack

If the ailerons are deflected to 10°, compared to 5°, this will cause: a. An increased angle of bank b. An increased rate of roll c. No change to either bank angle or roll rate d. A reduction in the adverse yawing moment

Description : If the ailerons are deflected to 10°, compared to 5°, this will cause: a. An increased angle of bank b. An increased rate of roll c. No change to either bank angle or roll rate d. A reduction in the adverse yawing moment

Last Answer : b. An increased rate of roll

What is the purpose of inboard ailerons? a. To reduce wing bending at high speed b. To reduce wing twisting at low speed c. To reduce wing bending at low speed d. To reduce wing twist at high speed

Description : What is the purpose of inboard ailerons? a. To reduce wing bending at high speed b. To reduce wing twisting at low speed c. To reduce wing bending at low speed d. To reduce wing twist at high speed

Last Answer : d. To reduce wing twist at high speed

If the steering stand selector switch is allowed to remain in the 'Non-Followup' mode after testing of the steering gear, the rudder will _____________. EL-0097 A. not respond to commands from the helm B. move in one direction only regardless of the movement of the helm C. not respond to output from the rotary actuator D. stop moving only when the helm is counter-rotated to put the pump at neutral stroke

Description : If the steering stand selector switch is allowed to remain in the 'Non-Followup' mode after testing of the steering gear, the rudder will _____________. EL-0097 A. not respond to commands from the ... actuator D. stop moving only when the helm is counter-rotated to put the pump at neutral stroke

Last Answer : Answer: A

What true airspeed and angle of attack should be used to generate the same amount of lift as altitude is increased? a. A higher true airspeed for any given angle of attack b. The same true airspeed and angle of attack c. A lower true airspeed and higher angle of attack d. A constant angle of attack and true airspeed

Description : What true airspeed and angle of attack should be used to generate the same amount of lift as altitude is increased? a. A higher true airspeed for any given angle of attack b. The same true ... c. A lower true airspeed and higher angle of attack d. A constant angle of attack and true airspeed

Last Answer : a. A higher true airspeed for any given angle of attack

How can the pilot increase the rate of turn and decrease the radius at the same time? a. Shallow the bank and increase airspeed b. Steeper bank and increase airspeed c. Steeper bank and decrease airspeed

Description : How can the pilot increase the rate of turn and decrease the radius at the same time? a. Shallow the bank and increase airspeed b. Steeper bank and increase airspeed c. Steeper bank and decrease airspeed

Last Answer : c. Steeper bank and decrease airspeed

Which wind-shear condition results in a loss of airspeed? a. Decreasing headwind or tailwind b. Increasing headwind and decreasing tailwind c. Decreasing headwind and increasing tailwind d. Increasing headwind or tailwind

Description : Which wind-shear condition results in a loss of airspeed? a. Decreasing headwind or tailwind b. Increasing headwind and decreasing tailwind c. Decreasing headwind and increasing tailwind d. Increasing headwind or tailwind

Last Answer : c. Decreasing headwind and increasing tailwind

What is the recommended technique to counter the loss of airspeed and resultant lift from wind shear? a. Maintain, or increase, pitch attitude and accept the lower-than-normal airspeed indications b. Lower the pitch attitude and regain lost airspeed c. Avoid overstressing aircraft, pitch to stick shaker, and apply maximum power d. Accelerate the aircraft to prevent a stall by sacrificing altitude

Description : What is the recommended technique to counter the loss of airspeed and resultant lift from wind shear? a. Maintain, or increase, pitch attitude and accept the lower-than-normal airspeed ... shaker, and apply maximum power d. Accelerate the aircraft to prevent a stall by sacrificing altitude

Last Answer : c. Avoid overstressing aircraft, pitch to stick shaker, and apply maximum power

t higher elevation airports the pilot should know that indicated airspeed: a. will be unchanged but ground speed will be faster b. will be higher but ground speed will be unchanged c. should be increased to compensate for the thinner air d. should be higher to obtain a higher landing speed

Description : t higher elevation airports the pilot should know that indicated airspeed: a. will be unchanged but ground speed will be faster b. will be higher but ground speed will be unchanged c. should be increased to compensate for the thinner air d. should be higher to obtain a higher landing speed

Last Answer : a. will be unchanged but ground speed will be faster

By changing the angle of attack of a wing, the pilot can control the aeroplane’s: a. Lift and airspeed, but not drag b. Lift, gross weight and drag c. Lift, airspeed and drag d. Lift and drag, but not airspeed

Description : By changing the angle of attack of a wing, the pilot can control the aeroplane’s: a. Lift and airspeed, but not drag b. Lift, gross weight and drag c. Lift, airspeed and drag d. Lift and drag, but not airspeed

Last Answer : c. Lift, airspeed and drag

A constant rate of climb in an aeroplane is determined by: a. Wind speed b. The aircraft weight c. Excess engine power d. Excess airspeed

Description : A constant rate of climb in an aeroplane is determined by: a. Wind speed b. The aircraft weight c. Excess engine power d. Excess airspeed

Last Answer : c. Excess engine power

If the angle of attack is increased beyond the critical angle of attack, the wing will no longer produce sufficient lift to support the weight of the aircraft: a. Unless the airspeed is greater than the normal stall speed b. Regardless of airspeed or pitch attitude c. Unless the pitch attitude is on or below the natural horizon d. In which case, the control column should be pulled-back immediately

Description : If the angle of attack is increased beyond the critical angle of attack, the wing will no longer produce sufficient lift to support the weight of the aircraft: a. Unless the airspeed is greater ... below the natural horizon d. In which case, the control column should be pulled-back immediately

Last Answer : b. Regardless of airspeed or pitch attitude

Shortly after take-off, the altitude of the aeroplane suffers an abrupt pitch-up and IAS rapidly decreases followed quickly by a decrease in altitude. Engine indications are normal. You should suspect what and what should you do? a. Marked temperature drop; apply full power b. Loss of head wind or an increase in tail wind; apply full power c. Incipient engine failure (ignore instruments); lower the nose to gain airspeed d. Local clear air turbulence; reduce speed to VRA and ride it out

Description : Shortly after take-off, the altitude of the aeroplane suffers an abrupt pitch-up and IAS rapidly decreases followed quickly by a decrease in altitude. Engine indications are normal. You should suspect what ... to gain airspeed d. Local clear air turbulence; reduce speed to VRA and ride it out

Last Answer : b. Loss of head wind or an increase in tail wind; apply full power

Two aircrafts, one with a sharp wing profile (S) and the other with a thick profile (T), are flying through the same cloud with the same true airspeed. The cloud consists of small supercooled droplets. Which of the following statements is most correct concerning ice accretion? a. Aircraft T experiences more icing than S b. Aircraft S and T experience the same amount of icing c. Neither of the aircrafts accumulate ice due to the small size of droplets d. Aircraft S experiences more icing than T

Description : Two aircrafts, one with a sharp wing profile (S) and the other with a thick profile (T), are flying through the same cloud with the same true airspeed. The cloud consists of small ... aircrafts accumulate ice due to the small size of droplets d. Aircraft S experiences more icing than T

Last Answer : d. Aircraft S experiences more icing than T

At a constant mass and altitude, a lower airspeed requires: a. More thrust and a lower coefficient of lift b. Less thrust and a lower coefficient of lift c. More thrust and a lower coefficient of drag d. A higher coefficient of lift

Description : At a constant mass and altitude, a lower airspeed requires: a. More thrust and a lower coefficient of lift b. Less thrust and a lower coefficient of lift c. More thrust and a lower coefficient of drag d. A higher coefficient of lift

Last Answer : d. A higher coefficient of lift

The longitudinal separation minimum based on time between aircrafts at the same FL, where there is enough coverage for navigation aids and the preceeding aircraft has a higher true airspeed of 20kts minimum is: a. 3 minutes b. 15 minutes c. 5 minutes d. 10 minutes

Description : The longitudinal separation minimum based on time between aircrafts at the same FL, where there is enough coverage for navigation aids and the preceeding aircraft has a higher true airspeed of 20kts minimum is: a. 3 minutes b. 15 minutes c. 5 minutes d. 10 minutes

Last Answer : c. 5 minutes

When entering a steep turn, an IVSI is likely to show: a. No change in altitude b. A slight climb c. A slight descent d. A slight descent at high airspeed only

Description : When entering a steep turn, an IVSI is likely to show: a. No change in altitude b. A slight climb c. A slight descent d. A slight descent at high airspeed only

Last Answer : b. A slight climb

Which of the following instruments require inputs of both pitot and static pressure? a. Airspeed indicator, machmeter and vertical speed indicator b. Airspeed indicator, vertical speed indicator, altimeter c. Airspeed indicator only d. Airspeed indicator and machmeter

Description : Which of the following instruments require inputs of both pitot and static pressure? a. Airspeed indicator, machmeter and vertical speed indicator b. Airspeed indicator, vertical speed indicator, altimeter c. Airspeed indicator only d. Airspeed indicator and machmeter

Last Answer : d. Airspeed indicator and machmeter

Total Air Temperature is: a. The maximum temperature attainable by the air when brought to rest, adiabatically b. The temperature indicated on the air temperature thermometer plus the ram rise c. The static air temperature minus the recovery factor d. The recovery factor plus the ram rise

Description : Total Air Temperature is: a. The maximum temperature attainable by the air when brought to rest, adiabatically b. The temperature indicated on the air temperature thermometer plus the ram rise c. The static air temperature minus the recovery factor d. The recovery factor plus the ram rise

Last Answer : a. The maximum temperature attainable by the air when brought to rest, adiabatically

To ensure some degree of longitudinal stability in flight, the position of the CG: a. Must always coincide with the AC b. Must be forward of the Neutral Point c. Must be aft of the Neutral Point d. Must not be forward of the aft CG limi

Description : To ensure some degree of longitudinal stability in flight, the position of the CG: a. Must always coincide with the AC b. Must be forward of the Neutral Point c. Must be aft of the Neutral Point d. Must not be forward of the aft CG limi

Last Answer : b. Must be forward of the Neutral Point

A nose wheel control system a. Prevents the nosewheel from castering at all times b. Allows the nosewheel to caster within preset limits about the neutral position c. Allows the nosewheel to caster freely at all times d. Prevents the nose gear from lowering if the nosewheels are not centralised

Description : A nose wheel control system a. Prevents the nosewheel from castering at all times b. Allows the nosewheel to caster within preset limits about the neutral position c. Allows the nosewheel to ... freely at all times d. Prevents the nose gear from lowering if the nosewheels are not centralised

Last Answer : b. Allows the nosewheel to caster within preset limits about the neutral position

In a Doppler VOR (DVOR) the reference signal is _____, the bearing signal is ______ and the direction of rotation of the bearing signal is ______. a. AM, FM, anti-clockwise b. AM, FM, clockwise c. FM, AM, anti-clockwise d. FM, AM, clockwise

Description : In a Doppler VOR (DVOR) the reference signal is _____, the bearing signal is ______ and the direction of rotation of the bearing signal is ______. a. AM, FM, anti-clockwise b. AM, FM, clockwise c. FM, AM, anti-clockwise d. FM, AM, clockwise

Last Answer : a. AM, FM, anti-clockwise

The instruction “ORBIT” from ATC means that the aircraft should: a. Carry out a go around b. Continue with 360 degree turns c. Carry out one 360 degree turn only d. Reverse the direction of the turn

Description : The instruction “ORBIT” from ATC means that the aircraft should: a. Carry out a go around b. Continue with 360 degree turns c. Carry out one 360 degree turn only d. Reverse the direction of the turn

Last Answer : c. Carry out one 360 degree turn only

What is the minimum vertical separation between IFR flights flying in the same direction below FL 290? a. 500ft b. 1000ft c. 2000ft d. 4000ft

Description : What is the minimum vertical separation between IFR flights flying in the same direction below FL 290? a. 500ft b. 1000ft c. 2000ft d. 4000ft

Last Answer : c. 2000ft

Aircraft A flies in VMC with an ATC clearance within a control area. Aircraft B without ATC clearance approaches at roughly the same height on a converging heading. Who has the right of way? a. Aircraft A, regardless of the direction from which B approaches b. Aircraft B, regardless of the direction from which A approaches c. Aircraft A, if B is to the right of him d. Aircraft B, if A is to the left of him

Description : Aircraft A flies in VMC with an ATC clearance within a control area. Aircraft B without ATC clearance approaches at roughly the same height on a converging heading. Who has the right of way? a. Aircraft A, regardless ... , if B is to the right of him d. Aircraft B, if A is to the left of him

Last Answer : d. Aircraft B, if A is to the left of him

If the weight of an aircraft is increased the maximum gliding range: a. Decreases b. Increases c. Remains the same, and rate of descent is unchanged d. Remains the same, but rate of descent increases

Description : If the weight of an aircraft is increased the maximum gliding range: a. Decreases b. Increases c. Remains the same, and rate of descent is unchanged d. Remains the same, but rate of descent increases

Last Answer : d. Remains the same, but rate of descent increases

What effect does aspect ratio have on induced drag? a. Increased aspect ratio increases induced drag b. Increased aspect ratio reduces induced drag c. Changing aspect ratio has no effect on induced drag d. Induced drag will equal 1:3 x aspect ratio/chord ratio

Description : What effect does aspect ratio have on induced drag? a. Increased aspect ratio increases induced drag b. Increased aspect ratio reduces induced drag c. Changing aspect ratio has no effect on induced drag d. Induced drag will equal 1:3 x aspect ratio/chord ratio

Last Answer : b. Increased aspect ratio reduces induced drag

Generally, as altitude increases: a. Temperature decreases and density increases b. Temperature, pressure and density decreases c. Temperature and pressure increase and density decreases d. Temperature decreases and pressure and density increase

Description : Generally, as altitude increases: a. Temperature decreases and density increases b. Temperature, pressure and density decreases c. Temperature and pressure increase and density decreases d. Temperature decreases and pressure and density increase

Last Answer : b. Temperature, pressure and density decreases

If you switch on the anti-collision light in IMC, what are the likely effects? a. Depth perception increases b. You can suffer from dizziness and disorientation c. You can suffer from Color Illusion d. Binocular vision is affected

Description : If you switch on the anti-collision light in IMC, what are the likely effects? a. Depth perception increases b. You can suffer from dizziness and disorientation c. You can suffer from Color Illusion d. Binocular vision is affected

Last Answer : b. You can suffer from dizziness and disorientation

The effects of carbon monoxide: a. Increases with altitude b. Decreases with altitude c. Increases with increase of density d. Decreases with pressure loss

Description : The effects of carbon monoxide: a. Increases with altitude b. Decreases with altitude c. Increases with increase of density d. Decreases with pressure loss

Last Answer : a. Increases with altitude

How is fuel consumption affect by the C of G position, in terms of ANM/kg? a. Increases with a forward C of G b. Decreases with an aft C of G c. Decreases with a forward C of G d. Fuel consumption is not affected by the C of G position

Description : How is fuel consumption affect by the C of G position, in terms of ANM/kg? a. Increases with a forward C of G b. Decreases with an aft C of G c. Decreases with a forward C of G d. Fuel consumption is not affected by the C of G position

Last Answer : c. Decreases with a forward C of G

You are flying at a constant FL 290 and a constant mach number. The total temperature increases by 5°. The CAS will: a. Remain approximately constant b. Increase by 10 kts c. Decrease by 10 kts d. Will increase or decrease depending on whether you are above or below ISA

Description : You are flying at a constant FL 290 and a constant mach number. The total temperature increases by 5°. The CAS will: a. Remain approximately constant b. Increase by 10 kts c. Decrease by 10 kts d. Will increase or decrease depending on whether you are above or below ISA

Last Answer : a. Remain approximately constant

When does a pilot apply the limitations of the MEL? a. At parking before commencement of taxi b. Prior to take-off c. At any time in flight d. Any time up to coming to a complete stop and applying the parking brake

Description : When does a pilot apply the limitations of the MEL? a. At parking before commencement of taxi b. Prior to take-off c. At any time in flight d. Any time up to coming to a complete stop and applying the parking brake

Last Answer : d. Any time up to coming to a complete stop and applying the parking brake

What is the absolute time a pilot should stop drinking before flying? a. 6 hours but it depends upon the amount of alcohol that has been consumed b. 24 hours but it depends upon the amount of alcohol that has been consumed c. 12 hours but it depends upon the amount of alcohol that has been consumed d. 8 hours but it depends upon the amount of alcohol that has been consumed

Description : What is the absolute time a pilot should stop drinking before flying? a. 6 hours but it depends upon the amount of alcohol that has been consumed b. 24 hours but it depends upon the amount of ... that has been consumed d. 8 hours but it depends upon the amount of alcohol that has been consumed

Last Answer : d. 8 hours but it depends upon the amount of alcohol that has been consumed

An example of a general call is: a. STOP IMMEDIATELY I SAY AGAIN STOP IMMEDAITELY b. BRAKING ACTION UNRELIABLE c. ALL STATIONS d. GOOD DAY

Description : An example of a general call is: a. STOP IMMEDIATELY I SAY AGAIN STOP IMMEDAITELY b. BRAKING ACTION UNRELIABLE c. ALL STATIONS d. GOOD DAY

Last Answer : c. ALL STATIONS

What is the purpose of inboard ailerons

Description : What is the purpose of inboard ailerons

Last Answer : D. to reduce wing twist at high speed

What is the purpose of inboard ailerons? a. To reduce wing bending at high speed b. To reduce wing twisting at low speed c. To reduce wing bending at low speed d. To reduce wing twist at high speed

Description : What is the purpose of inboard ailerons? a. To reduce wing bending at high speed b. To reduce wing twisting at low speed c. To reduce wing bending at low speed d. To reduce wing twist at high speed

Last Answer : d. To reduce wing twist at high speed

The advantage of a constant speed propeller over a fixed pitch propeller is: a. Higher maximum thrust available b. Higher maximum efficiency c. More blade surface area available d. Nearly maximum efficiency over wide speed range

Description : The advantage of a constant speed propeller over a fixed pitch propeller is: a. Higher maximum thrust available b. Higher maximum efficiency c. More blade surface area available d. Nearly maximum efficiency over wide speed range

Last Answer : d. Nearly maximum efficiency over wide speed range

If airbrakes are extended during a glide, and speed maintained, the rate of descent will: a. Increase and glide angle will be steeper b. Increase but glide angle will remain the same c. Decrease d. Remain the same

Description : If airbrakes are extended during a glide, and speed maintained, the rate of descent will: a. Increase and glide angle will be steeper b. Increase but glide angle will remain the same c. Decrease d. Remain the same

Last Answer : a. Increase and glide angle will be steeper

An aircraft has a L/D ratio of 15:1 at 50kts in calm air. What would the L/D ratio be with a direct headwind of 25kts? a. 30:1 b. 15:1 c. 25:1 d. 7.5:1

Description : An aircraft has a L/D ratio of 15:1 at 50kts in calm air. What would the L/D ratio be with a direct headwind of 25kts? a. 30:1 b. 15:1 c. 25:1 d. 7.5:1

Last Answer : b. 15:1

To maintain altitude, what must be done as Indicated Airspeeed (IAS) is reduced? a. Decrease angle of attack to reduce the drag b. Increase angle of attack to maintain the correct lift force c. Deploy the speed brakes to increase drag d. Reduce thrust

Description : To maintain altitude, what must be done as Indicated Airspeeed (IAS) is reduced? a. Decrease angle of attack to reduce the drag b. Increase angle of attack to maintain the correct lift force c. Deploy the speed brakes to increase drag d. Reduce thrust

Last Answer : b. Increase angle of attack to maintain the correct lift force

What flight condition should be expected when an aircraft leaves ground effect? a. A decrease in parasite drag permitting a lower angle of attack b. An increase induced drag and a requirement for a higher angle of attack c. An increase in dynamic stability d. A decrease in induced drag requiring a smaller angle of attack

Description : What flight condition should be expected when an aircraft leaves ground effect? a. A decrease in parasite drag permitting a lower angle of attack b. An increase induced drag and a requirement ... increase in dynamic stability d. A decrease in induced drag requiring a smaller angle of attack

Last Answer : b. An increase induced drag and a requirement for a higher angle of attack

An aircraft has a stalling speed in level flight of 70kt IAS. In a 60° balanced turn, the stalling speed would be: a. 76kt b. 84kt c. 99kt d. 140kt

Description : An aircraft has a stalling speed in level flight of 70kt IAS. In a 60° balanced turn, the stalling speed would be: a. 76kt b. 84kt c. 99kt d. 140kt

Last Answer : c. 99kt

If flaps are lowered during the take-off run: a. The lift would not change until the aircraft is airborne b. The lift would increase when the flaps are lowered c. The lift would decrease d. The acceleration would increase

Description : If flaps are lowered during the take-off run: a. The lift would not change until the aircraft is airborne b. The lift would increase when the flaps are lowered c. The lift would decrease d. The acceleration would increase

Last Answer : b. The lift would increase when the flaps are lowered

If a landing is to be made without flaps, the landing speed must be: a. reduced b. increased c. the same as for landing with flaps d. the same as for landing with flaps but with a steeper approach

Description : If a landing is to be made without flaps, the landing speed must be: a. reduced b. increased c. the same as for landing with flaps d. the same as for landing with flaps but with a steeper approach

Last Answer : b. increased