What property of a metal describes the onset of plastic deformation in a tensile test? w) tensile strength x) elongation y) yield strength z) reduction in area

What property of a metal describes the onset of plastic deformation in a tensile test? w) tensile strength x) elongation y) yield strength z) reduction in area
by

1 Answer

Answer :

ANSWER: Y -- YIELD STRENGTH
by

Related questions

The ability of a material to resist plastic deformation known as _____________ a) Tensile strength b) Yield strength c) Modulus of elasticity d) Impact strength

Description : The ability of a material to resist plastic deformation known as _____________ a) Tensile strength b) Yield strength c) Modulus of elasticity d) Impact strength

Last Answer : b) Yield strength

The percentage elongation and the percentage reduction in area depends upon (a) Tensile strength of the material (b) Ductility of the material (c) Toughness of the material (d) None of these

Description : The percentage elongation and the percentage reduction in area depends upon (a) Tensile strength of the material (b) Ductility of the material (c) Toughness of the material (d) None of these

Last Answer : B

Which of the following physical properties is TRUE of most dense ceramic materials? w) high tensile strength x) good ductility y) high compressive strength z) high electrical conductivity

Description : Which of the following physical properties is TRUE of most dense ceramic materials? w) high tensile strength x) good ductility y) high compressive strength z) high electrical conductivity

Last Answer : ANSWER: Y -- HIGH COMPRESSIVE STRENGTH

The ductility of metal is usually expressed in terms of the: A. Yield strength (point where the material is not longer elastic) B. Percent elongation C. Modulus of elasticity (stiffness of the material)

Description : The ductility of metal is usually expressed in terms of the: A. Yield strength (point where the material is not longer elastic) B. Percent elongation C. Modulus of elasticity (stiffness of the material)

Last Answer : B. Percent elongation

At yield point of a test piece, the material (A) Obeys Hooke's law (B) Behaves in an elastic manner (C) Regains its original shape on removal of the load(D) Undergoes plastic deformation

Description : At yield point of a test piece, the material  (A) Obeys Hooke's law  (B) Behaves in an elastic manner  (C) Regains its original shape on removal of the load  (D) Undergoes plastic deformation 

Last Answer : (D) Undergoes plastic deformation 

The property of material, by which a given amount of energy is absorbed by it without plastic deformation, is called the (A) Resilience (B) Toughness (C) Ductility (D) Impact strength

Description : The property of material, by which a given amount of energy is absorbed by it without plastic deformation, is called the (A) Resilience (B) Toughness (C) Ductility (D) Impact strength

Last Answer : (A) Resilience

The property of material, by which a given amount of energy is absorbed by it, without plastic deformation, is called (A) Resilience (B) Toughness (C) Ductility (D) Impact strength

Description : The property of material, by which a given amount of energy is absorbed by it, without plastic deformation, is called (A) Resilience (B) Toughness (C) Ductility (D) Impact strength

Last Answer : (A) Resilience

(A) Percentage elongation (B) Yield strength (C) Ultimate strength (D) Area under stress-strain diagram

Description : (A) Percentage elongation (B) Yield strength (C) Ultimate strength (D) Area under stress-strain diagram

Last Answer : (B) Yield strength

The most critical consideration in the design of a rolled steel column carrying axial loads is the (a) Percentage elongation at yield and the net cross-sectional area (b) Critical bending strength and axial yield strength of material (c) Buckling strength based on the net area of the section and percentage elongation at ultimate load (d) Compressive strength based on slenderness ratio and gross cross-sectional area.

Description : The most critical consideration in the design of a rolled steel column carrying axial loads is the (a) Percentage elongation at yield and the net cross-sectional area (b) Critical bending ... at ultimate load (d) Compressive strength based on slenderness ratio and gross cross-sectional area.

Last Answer : (d) Compressive strength based on slenderness ratio and gross cross-sectional area.

An ideal plastic substance indicates no deformation, when stressed upto yield stress, but behaves like a Newtonian fluid beyond yield stress. Which of the following is an ideal plastic? (A) Sewage sludge (B) Rubber latex (C) Blood (D) Sugar solution

Description : An ideal plastic substance indicates no deformation, when stressed upto yield stress, but behaves like a Newtonian fluid beyond yield stress. Which of the following is an ideal plastic? (A) Sewage sludge (B) Rubber latex (C) Blood (D) Sugar solution

Last Answer : (A) Sewage sludge

With increasing carbon percent in steel beyond 0.8%, its ultimate tensile strength (UTS) and __________ is not affected. (A) Impact strength (B) Percent elongation (C) Hardness (D) Both 'b' & 'c'

Description : With increasing carbon percent in steel beyond 0.8%, its ultimate tensile strength (UTS) and __________ is not affected. (A) Impact strength (B) Percent elongation (C) Hardness (D) Both 'b' & 'c'

Last Answer : (A) Impact strength

In case of brasses, with decreasing zinc percentage and increasing copper percentage, its __________ increases. (A) Percentage elongation (B) Brinell hardness (C) Tensile strength (D) All 'a', 'b' & 'c'

Description : In case of brasses, with decreasing zinc percentage and increasing copper percentage, its __________ increases. (A) Percentage elongation (B) Brinell hardness (C) Tensile strength (D) All 'a', 'b' & 'c'

Last Answer : (A) Percentage elongation

A simply supported uniform rectangular bar breadth b, depth d and length L carries an isolated load W at its mid-span. The same bar experiences an extension e under same tensile load. The ratio of the maximum deflection to the elongation, is (A) L/d (B) L/2d (C) (L/2d)² (D) (L/3d)²

Description : A simply supported uniform rectangular bar breadth b, depth d and length L carries an isolated  load W at its mid-span. The same bar experiences an extension e under same tensile load. The  ratio of the maximum deflection to the ... (A) L/d (B) L/2d (C) (L/2d)² (D) (L/3d)²

Last Answer : (C) (L/2d)

The property due to which a metal can be hammered into thin sheets without breaking is _______. a) malleability b)ductility c)tensile strength d)conductivity

Description : The property due to which a metal can be hammered into thin sheets without breaking is _______. a) malleability b)ductility c)tensile strength d)conductivity

Last Answer : a) malleability

While the thermosetting polymers are amorphous in nature, the thermoplastic polymers are either amorphous or crystalline. The crystalline polymers are characterised by the (A) Low impact strength (B) High flexibility (C) Better finish and surface appearance (D) High plastic deformation

Description : While the thermosetting polymers are amorphous in nature, the thermoplastic polymers are either amorphous or crystalline. The crystalline polymers are characterised by the (A) Low impact strength (B) High flexibility (C) Better finish and surface appearance (D) High plastic deformation

Last Answer : A) Low impact strength

What Properties Are Needed To Be Considered For Application Calling For Following Requirements? I) Rigidity. Ii) Strength Of No Plastic Deformation Under Static Load. Iii) Strength To Withstand Overload Without Fracture.

Description : What Properties Are Needed To Be Considered For Application Calling For Following Requirements? I) Rigidity. Ii) Strength Of No Plastic Deformation Under Static Load. Iii) Strength To Withstand Overload Without Fracture.

Last Answer : i) Reliability – elastic modulus and yield strength. ii) Strength (for no plastic deformation under static loading) – yield point. iii) Strength (overload) – Toughness and impact resistance. iv) Wear resistance – Hardness. v) Reliability and safety – Endurance limit and yield.

In an all weld tensile test, the original specimen gauge length was 50mm, and after the test the increased gauge length was 65mm, what is the elongation percentage? a) % A is 40 b) % A is 60 c) % A is 30 d) % A is 36

Description : In an all weld tensile test, the original specimen gauge length was 50mm, and after the test the increased gauge length was 65mm, what is the elongation percentage? a) % A is 40 b) % A is 60 c) % A is 30 d) % A is 36

Last Answer : c) % A is 30

Percentage elongation during tensile test is indication of (a) Ductility (b) Malleability (c) Creep (d) Rigidity

Description : Percentage elongation during tensile test is indication of (a) Ductility (b) Malleability (c) Creep (d) Rigidity

Last Answer : (a) Ductility

Shear stress causes (a) Deformation (b)Elongation (c) Contraction (d) None

Description : Shear stress causes (a) Deformation (b)Elongation (c) Contraction (d) None

Last Answer : (d) None

…. is the property of a material which enables it to resist plastic deformation.

Description : …. is the property of a material which enables it to resist plastic deformation.

Last Answer : …. is the property of a material which enables it to resist plastic deformation. (A) elasticity (B) plasticity (C) hardness (D) ductility

Which of the following mechanical properties of a material is most structure insensitive? (A) Modulus of elasticity (young's modulus) (B) Toughness (C) Percentage reduction of area (D) Tensile strength

Description : Which of the following mechanical properties of a material is most structure insensitive? (A) Modulus of elasticity (young's modulus) (B) Toughness (C) Percentage reduction of area (D) Tensile strength

Last Answer : (A) Modulus of elasticity (young's modulus)

A reduction reaction always involves the: w) loss of electrons x) gain of electrons y) addition of oxygen z) removal of oxygen

Description : A reduction reaction always involves the: w) loss of electrons x) gain of electrons y) addition of oxygen z) removal of oxygen

Last Answer : ANSWER: X -- GAIN OF ELECTRONS

Pick out the correct statement. (A) Stainless steel is nothing but chromium coated steel (B) Hardening of a soft metal can be done by alloying it with another metal or non-metal (C) Plastic deformation of a material is its temporary distortion under the action of applied stress (D) Rusting of iron is not electrochemical in nature

Description : Pick out the correct statement. (A) Stainless steel is nothing but chromium coated steel (B) Hardening of a soft metal can be done by alloying it with another metal or non-metal (C) ... its temporary distortion under the action of applied stress (D) Rusting of iron is not electrochemical in nature

Last Answer : (B) Hardening of a soft metal can be done by alloying it with another metal or non-metal

The index of refraction of a plastic material is 1.5. The speed of light in this material relative to that in a vacuum is: w) 2 x) 1.5 y) 2/3 z) 1/2

Description : The index of refraction of a plastic material is 1.5. The speed of light in this material relative to that in a vacuum is: w) 2 x) 1.5 y) 2/3 z) 1/2

Last Answer : ANSWER: Y -- 2/3

The coating on the plastic tape you use in your cassette players is w) diamagnetic x) paramagnetic y) ferromagnetic z) a permanent magnet

Description : The coating on the plastic tape you use in your cassette players is w) diamagnetic x) paramagnetic y) ferromagnetic z) a permanent magnet

Last Answer : ANSWER: Y -- FERROMAGNETIC

When the steel is subjected to normalising, its __________ decreases. (A) Yield point (B) Ductility (C) Ultimate tensile strength (UTS)

Description : When the steel is subjected to normalising, its __________ decreases. (A) Yield point (B) Ductility (C) Ultimate tensile strength (UTS)

Last Answer : (B) Ductility

Failure of a material is termed as fatigue failure, if it fails below the yield point. The resistance to fatigue failure of a material is measured by the (A) Ultimate tensile strength (U.T.S.) (B) Endurance limit (C) Elastic limit (D) None of these

Description : Failure of a material is termed as fatigue failure, if it fails below the yield point. The resistance to fatigue failure of a material is measured by the (A) Ultimate tensile strength (U.T.S.) (B) Endurance limit (C) Elastic limit (D) None of these

Last Answer : (B) Endurance limit

Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Description : Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Last Answer : (c) endurance limit to the working stress

The yield strength and tensile strength of low carbon steel may be improved by the addition of (A) Manganese (B) Chromium (C) Nickel (D) Vanadium

Description : The yield strength and tensile strength of low carbon steel may be improved by the addition of (A) Manganese (B) Chromium (C) Nickel (D) Vanadium

Last Answer : Answer: Option D

Wohler test is a destructive test to find out the __________ strength of a prepared metal specimen. (A) Creep (B) Fatigue (C) Endurance (D) Tensile

Description : Wohler test is a destructive test to find out the __________ strength of a prepared metal specimen. (A) Creep (B) Fatigue (C) Endurance (D) Tensile

Last Answer : (B) Fatigue

Which one of the following laws best describes the operation of an electric generator? w) Ampere's Law x) Gauss' Law y) Ohm's Law for Conductors z) Faraday's Law of Induction

Description : Which one of the following laws best describes the operation of an electric generator? w) Ampere's Law x) Gauss' Law y) Ohm's Law for Conductors z) Faraday's Law of Induction

Last Answer : ANSWER: Z -- FARADAY'S LAW OF INDUCTION 

For the hydrogen atom, which series describes electron transitions to the N = 2 orbit? Is it the: w) Lyman series x) Paschen series y) Balmer series z) Pfund series

Description : For the hydrogen atom, which series describes electron transitions to the N = 2 orbit? Is it the: w) Lyman series x) Paschen series y) Balmer series z) Pfund series

Last Answer : ANSWER: Y -- BALMER SERIES

What law describes the force between two stationary electrically charged objects? w) Ampere's law x) Coulomb's law y) Kirchoff's Rules (pron: kir-koff rules) z) Ohm's law

Description : What law describes the force between two stationary electrically charged objects? w) Ampere's law x) Coulomb's law y) Kirchoff's Rules (pron: kir-koff rules) z) Ohm's law

Last Answer : ANSWER: X -- COULOMB'S LAW

For the hydrogen atom, which series describes electron transitions to the N=1 orbit, the lowest energy electron orbit? Is it the: w) Lyman series x) Balmer series y) Paschen series z) Pfund series

Description : For the hydrogen atom, which series describes electron transitions to the N=1 orbit, the lowest energy electron orbit? Is it the: w) Lyman series x) Balmer series y) Paschen series z) Pfund series

Last Answer : ANSWER: W -- LYMAN SERIES

Substances that elongate considerably and undergo plastic deformation before they break are known as A. brittle substances B. breakable substances C. ductile substances D. elastic substances

Description : Substances that elongate considerably and undergo plastic deformation before they break are known as A. brittle substances B. breakable substances C. ductile substances D. elastic substances

Last Answer : ductile substances

Which of the following phrases completes the following statement: The strength of the electric field between two oppositely charged parallel plates is: w) a maximum midway between the plates x) a maximum near the positively charged plate y) constant between the plates except near the edges z) zero midway between the plates

Description : Which of the following phrases completes the following statement: The strength of the electric field between two oppositely charged parallel plates is: w) a maximum midway between the plates x) a maximum ... plate y) constant between the plates except near the edges z) zero midway between the plates

Last Answer : ANSWER: Y -- CONSTANT BETWEEN THE PLATES EXCEPT NEAR THE EDGES

The Tesla and the Gauss are units of measure of: w) conductance x) magnetic field strength y) magnetic flux z) electrical current

Description : The Tesla and the Gauss are units of measure of: w) conductance x) magnetic field strength y) magnetic flux z) electrical current

Last Answer : ANSWER: X -- MAGNETIC FIELD STRENGTH

Ice skating is possible and practical because of a unique property of water. Is it because: w) The coefficient of kinetic friction of steel on frozen water decreases with decreasing temperature x) Ice readily sublimes y) The melting point decreases with increasing pressure z) Ice is a good thermal insulator

Description : Ice skating is possible and practical because of a unique property of water. Is it because: w) The coefficient of kinetic friction of steel on frozen water decreases with decreasing temperature x ... sublimes y) The melting point decreases with increasing pressure z) Ice is a good thermal insulator 

Last Answer : ANSWER: Y -- THE MELTING POINT DECREASES WITH INCREASING PRESSURE 

A bimetallic strip commonly found in home furnace thermostats works because of the difference in this property of the two metals. Is it: w) thermal shock x) thermal conductivity y) thermal expansion z) thermal diffusivity

Description : A bimetallic strip commonly found in home furnace thermostats works because of the difference in this property of the two metals. Is it: w) thermal shock x) thermal conductivity y) thermal expansion z) thermal diffusivity

Last Answer : ANSWER: Y -- THERMAL EXPANSION

When a physical property such as charge exists in discrete "packets" rather than in continuous amounts, the property is said to be: w) discontinuous x) abrupt y) quantized z) noncontinuous

Description : When a physical property such as charge exists in discrete "packets" rather than in continuous amounts, the property is said to be: w) discontinuous x) abrupt y) quantized z) noncontinuous

Last Answer : ANSWER: Y -- QUANTIZED

Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Description : Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Last Answer : (C) Creep resistance

Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Description : Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

The form of the fuel in U.S. commercial nuclear power plants is which of the following: w) uranium oxide ceramic pellets x) atomic vapor y) uranium metal tubes z) uranium solution in water

Description : The form of the fuel in U.S. commercial nuclear power plants is which of the following: w) uranium oxide ceramic pellets x) atomic vapor y) uranium metal tubes z) uranium solution in water

Last Answer : ANSWER: W -- URANIUM OXIDE CERAMIC PELLETS

Four identical samples of a metal are heated to different temperatures. Based on the colors of their incandescences, which sample is the hottest? The sample that is: w) blue-white x) bright red y) yellow z) orange

Description : Four identical samples of a metal are heated to different temperatures. Based on the colors of their incandescences, which sample is the hottest? The sample that is: w) blue-white x) bright red y) yellow z) orange

Last Answer : ANSWER: W -- BLUE-WHITE

Close inspection of a failed metal part reveals artifacts on the fracture surface commonly referred to as "striations" or "beach marks". This indicates the component failed as a result of: w) Sudden overloading x) Cyclical loading y) Stress corrosion cracking z) None of the above

Description : Close inspection of a failed metal part reveals artifacts on the fracture surface commonly referred to as "striations" or "beach marks". This indicates the component failed as a result of: w) Sudden overloading x) Cyclical loading y) Stress corrosion cracking z) None of the above

Last Answer : ANSWER: X -- CYCLICAL LOADING

According to Gauss' Law, the magnitude of the electric field is zero everywhere inside a conductor if: w) electrostatic equilibrium is achieved x) the surface is a metal y) the conductor is moving z) the conductor is a non-Gaussian surface

Description : According to Gauss' Law, the magnitude of the electric field is zero everywhere inside a conductor if: w) electrostatic equilibrium is achieved x) the surface is a metal y) the conductor is moving z) the conductor is a non-Gaussian surface

Last Answer : ANSWER: W -- ELECTROSTATIC EQUILIBRIUM IS ACHIEVED

When a certain beam of light falls upon a metal surface, it ejects photoelectrons from it. The number of photoelectrons ejected per second by the beam of light depends upon one of the following. Is it proportional to: w) the threshold frequency of the metal x) the work function of the metal y) the frequency of the beam z) the intensity of the beam

Description : When a certain beam of light falls upon a metal surface, it ejects photoelectrons from it. The number of photoelectrons ejected per second by the beam of light depends upon one of the following. Is it ... the work function of the metal y) the frequency of the beam z) the intensity of the beam

Last Answer : ANSWER: Z -- THE INTENSITY OF THE BEAM

A metal ball on an insulated stand is touched by a positively charged glass rod. What happens to the metal ball? Does it w) gain protons and lose electrons x) gain protons y) gain more protons than electrons z) lose electrons

Description : A metal ball on an insulated stand is touched by a positively charged glass rod. What happens to the metal ball? Does it w) gain protons and lose electrons x) gain protons y) gain more protons than electrons z) lose electrons

Last Answer : ANSWER: Z -- LOSE ELECTRONS

In a charged hollow metal conductor, the charge is w) on the inside surface only x) on both the inside and outside surfaces y) on the outside surface only z) only between the inside and outside surfaces

Description : In a charged hollow metal conductor, the charge is w) on the inside surface only x) on both the inside and outside surfaces y) on the outside surface only z) only between the inside and outside surfaces

Last Answer : ANSWER: Y -- ON THE OUTSIDE SURFACE ONLY

What is the only non-metal element that is a liquid at room temperature and one atmosphere? w) bromine x) argon y) silicon z) selenium

Description : What is the only non-metal element that is a liquid at room temperature and one atmosphere? w) bromine x) argon y) silicon z) selenium

Last Answer : ANSWER: W -- BROMINE