Modulus of rupture of concrete is a measure of (A) Flexural tensile strength (B) Direct tensile strength (C) Compressive strength (D) Split tensile strength

Modulus of rupture of concrete is a measure of
(A) Flexural tensile strength
(B) Direct tensile strength
(C) Compressive strength
(D) Split tensile strength
by

1 Answer

Answer :

Answer: Option A
by

Related questions

The relation between modulus of rupture fcr, splitting strength fcs and direct tensile strength fcl is given by (A) fcr - fcs = fcl (B) fcr > fcs > fcl (C) fcr < fcs < fcl (D) fcs > fcr > fcl

Description : The relation between modulus of rupture fcr, splitting strength fcs and direct tensile strength fcl is given by (A) fcr - fcs = fcl (B) fcr > fcs > fcl (C) fcr < fcs < fcl (D) fcs > fcr > fcl

Last Answer : Option B

Steel rods are normally used for concrete reinforcement because concrete and steel have almost equal (A) Tensile strength (B) Compressive strength (C) Young's modulus (D) Thermal co-efficient of expansion

Description : Steel rods are normally used for concrete reinforcement because concrete and steel have almost equal (A) Tensile strength (B) Compressive strength (C) Young's modulus (D) Thermal co-efficient of expansion

Last Answer : (D) Thermal co-efficient of expansion

According to IS: 4561978, the flexural strength of concrete is (A) Directly proportional to compressive strength (B) Inversely proportional to compressive strength (C) Directly proportional to square root of compressive strength (D) Inversely proportional to square root of compressive strength

Description : According to IS: 4561978, the flexural strength of concrete is (A) Directly proportional to compressive strength (B) Inversely proportional to compressive strength (C) Directly proportional to square root of compressive strength (D) Inversely proportional to square root of compressive strength

Last Answer : Answer: Option C

For lime concrete, (A) Slump is 50 to 75 mm (B) Flexural strength at 90 days is 0.2 N/mm2 (C) Compressive strength at 90 days is 1.5 N/mm2 (D) All the above

Description : For lime concrete, (A) Slump is 50 to 75 mm (B) Flexural strength at 90 days is 0.2 N/mm2 (C) Compressive strength at 90 days is 1.5 N/mm2 (D) All the above

Last Answer : Answer: Option D

Workability of concrete mix with low water cement ratio is determined by (A) Tensile strength test (B) Slump test (C) Compaction factor test (D) Flexural strength test

Description : Workability of concrete mix with low water cement ratio is determined by (A) Tensile strength test (B) Slump test (C) Compaction factor test (D) Flexural strength test

Last Answer : Answer: Option C

Workability of concrete mix with low water cement ratio is determined by [ A ] Tensile strength test [ B ] Slump cone test [ C ] Compaction factor test [ D ] Flexural strength test

Description : Workability of concrete mix with low water cement ratio is determined by [ A ] Tensile strength test [ B ] Slump cone test [ C ] Compaction factor test [ D ] Flexural strength test

Last Answer : [ C ] Compaction factor test

Slump test of concrete is a measure of its (A) Consistency (B) Compressive strength (C) Tensile strength (D) Impact value

Description : Slump test of concrete is a measure of its (A) Consistency (B) Compressive strength (C) Tensile strength (D) Impact value

Last Answer : (A) Consistency

Slump test of concrete is a measure of its (A) Consistency (B) Compressive strength (C) Tensile strength (D) Impact value

Description : Slump test of concrete is a measure of its (A) Consistency (B) Compressive strength (C) Tensile strength (D) Impact value

Last Answer : (A) Consistency

Slump test of concrete is a measure of its [ A ] Consistency [ B ] Compressive strength [ C ] Tensile strength [ D ] Impact value

Description : Slump test of concrete is a measure of its [ A ] Consistency [ B ] Compressive strength [ C ] Tensile strength [ D ] Impact value

Last Answer : [ A ] Consistency

The approximate value of the ratio between direct tensile strength and flexural strength is (A) 0.33 (B) 0.5 (C) 0.75 (D) 1.0

Description : The approximate value of the ratio between direct tensile strength and flexural strength is (A) 0.33 (B) 0.5 (C) 0.75 (D) 1.0

Last Answer : Answer: Option B

A higher modular ratio shows (A) Higher compressive strength of concrete (B) Lower compressive strength of concrete (C) Higher tensile strength of steel (D) Lower tensile strength of steel

Description : A higher modular ratio shows (A) Higher compressive strength of concrete (B) Lower compressive strength of concrete (C) Higher tensile strength of steel (D) Lower tensile strength of steel

Last Answer : Answer: Option B

Allowable shear strength of concrete, depends upon (A) Shear strength (B) Tensile strength (C) Compressive strength (D) None of these

Description : Allowable shear strength of concrete, depends upon (A) Shear strength (B) Tensile strength (C) Compressive strength (D) None of these

Last Answer : Answer: Option A

Normally, the tensile strength of concrete is about____________of its compressive strength (a) 10 to 15% (b) 15 to 20% (c) 20 to 25% (d) 25 to 30%

Description : Normally, the tensile strength of concrete is about____________of its compressive strength (a) 10 to 15% (b) 15 to 20% (c) 20 to 25% (d) 25 to 30%

Last Answer : (a) 10 to 15%

The tensile strength of concrete is about ________ of its compressive strength [ A ] 10% to 15% [ B ] 30% to 40% [ C ] 50% [ D ] 60% to 75%

Description : The tensile strength of concrete is about ________ of its compressive strength [ A ] 10% to 15% [ B ] 30% to 40% [ C ] 50% [ D ] 60% to 75%

Last Answer : [ A ] 10% to 15%

At any point of a beam, the section modulus may be obtained by dividing the moment of inertia of the section by (A) Depth of the section (B) Depth of the neutral axis (C) Maximum tensile stress at the section (D) Maximum compressive stress at the section

Description : At any point of a beam, the section modulus may be obtained by dividing the moment of inertia of  the section by  (A) Depth of the section  (B) Depth of the neutral axis  (C) Maximum tensile stress at the section  (D) Maximum compressive stress at the section

Last Answer : (B) Depth of the neutral axis 

The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of 4 tonnes at the centre. The maximum stress in the bottom most fibre at the mid span section, is (A) 13.33 kg/cm2 tensile (B) 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Description : The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of ... 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Last Answer : (C) 26.67 kg/cm2 tensile

I need ways to test/get data about homemade plastics. What can I do with Flexural Strength and Flexural Modulus...

Description : I need ways to test/get data about homemade plastics. What can I do with Flexural Strength and Flexural Modulus...

Last Answer : answer:Strength is how strong a material is – basically breaking load. Modulus is how flexible or stretchy a material is. Does not matter if the test coupon breaks or not. Think of uncooked spaghetti vs rubber band.

Steel rods are used in reinforced concrete to increase its __________ strength. (A) Shear (B) Tensile (C) Compressive (D) None of these

Description : Steel rods are used in reinforced concrete to increase its __________ strength. (A) Shear (B) Tensile (C) Compressive (D) None of these

Last Answer : (B) Tensile

Young's modulus of a material is the measure of its (A) Stiffness (B) Malleability (C) Creep resistance (D) Tensile strength

Description : Young's modulus of a material is the measure of its (A) Stiffness (B) Malleability (C) Creep resistance (D) Tensile strength

Last Answer : Option A

Elastomers are (A) Thermosetting material (B) Exemplified by protein derivatives (C) Having high flexural strength (D) Having very high tensile strength and heat resistance

Description : Elastomers are (A) Thermosetting material (B) Exemplified by protein derivatives (C) Having high flexural strength (D) Having very high tensile strength and heat resistance

Last Answer : (C) Having high flexural strength

To determine the modulus of rupture, the size of test specimen used is (A) 150 × 150 × 500 mm (B) 100 × 100 × 700 mm (C) 150 × 150 × 700 mm (D) 100 × 100 × 500 mm

Description : To determine the modulus of rupture, the size of test specimen used is (A) 150 × 150 × 500 mm (B) 100 × 100 × 700 mm (C) 150 × 150 × 700 mm (D) 100 × 100 × 500 mm

Last Answer : Answer: Option C

In symmetrically reinforced sections, shrinkage stresses in concrete and steel are respectively (A) Compressive and tensile (B) Tensile and compressive (C) Both compressive (D) Both tensile

Description : In symmetrically reinforced sections, shrinkage stresses in concrete and steel are respectively (A) Compressive and tensile (B) Tensile and compressive (C) Both compressive (D) Both tensile

Last Answer : Answer: Option D

The purpose of reinforcement in pre-stressed concrete is (A) To provide adequate bond stress (B) To resist tensile stresses (C) To impart initial compressive stress in concrete (D) All of the above

Description : The purpose of reinforcement in pre-stressed concrete is (A) To provide adequate bond stress (B) To resist tensile stresses (C) To impart initial compressive stress in concrete (D) All of the above

Last Answer : Answer: Option C

The longitudinal shearing stresses acting on the surface between the steel and concrete are called. (a) Bond stress (b) Tensile stresses (c) Compressive stresses (d) None of these

Description : The longitudinal shearing stresses acting on the surface between the steel and concrete are called. (a) Bond stress (b) Tensile stresses (c) Compressive stresses (d) None of these

Last Answer : (a) Bond stress

The moment of resistance of an over-reinforcement section is determined on the basis of (a) Compressive force developed in concrete (b) Tensile force developed in steel (c) Both (a) & (b) (d) None of these

Description : The moment of resistance of an over-reinforcement section is determined on the basis of (a) Compressive force developed in concrete (b) Tensile force developed in steel (c) Both (a) & (b) (d) None of these

Last Answer : (a) Compressive force developed in concrete

The moment of resistance of an under- reinforced section is computer on the basis of (a) Compressive force developed in concrete (b) Tensile force developed in steel (c) Both (a) & (b) (d) All the above

Description : The moment of resistance of an under- reinforced section is computer on the basis of (a) Compressive force developed in concrete (b) Tensile force developed in steel (c) Both (a) & (b) (d) All the above

Last Answer : (b) Tensile force developed in steel

Plain cement concrete is strong in taking (a) Compressive stress. (b) Tensile stress (c) Shear stress (d) All of these

Description : Plain cement concrete is strong in taking (a) Compressive stress. (b) Tensile stress (c) Shear stress (d) All of these

Last Answer : (a) Compressive stress.

Reinforced cement concrete is equally strong in taking (a) Tensile and compressive stress (b) Compressive and shear stresses. (c) Tensile, compressive and shear stresses. (d) Tensile and shear stresses.

Description : Reinforced cement concrete is equally strong in taking (a) Tensile and compressive stress (b) Compressive and shear stresses. (c) Tensile, compressive and shear stresses. (d) Tensile and shear stresses.

Last Answer : (c) Tensile, compressive and shear stresses.

Le-Chatelier's device is used for determining the (A) Setting time of cement (B) Soundness of cement (C) Tensile strength of cement (D) Compressive strength of cement

Description : Le-Chatelier's device is used for determining the (A) Setting time of cement (B) Soundness of cement (C) Tensile strength of cement (D) Compressive strength of cement

Last Answer : Answer: Option B

Compared to mild steel, cast iron has (i) High compressive strength (ii) High tensile strength (iii) Low compressive strength (iv) Low tensile strength The correct answer is (A) (i) and (ii) (B) (ii) and (iii) (C) (iii) and (iv) (D) (i) and (iv)

Description : Compared to mild steel, cast iron has (i) High compressive strength (ii) High tensile strength (iii) Low compressive strength (iv) Low tensile strength The correct answer is (A) (i) and (ii) (B) (ii) and (iii) (C) (iii) and (iv) (D) (i) and (iv)

Last Answer : Answer: Option D

For testing compressive and tensile strength of cement, the cement mortar is made by mixing cement and standard sand in the proportions of (A) 1 : 2 (B) 1 : 3 (C) 1 : 4 (D) 1 : 6

Description : For testing compressive and tensile strength of cement, the cement mortar is made by mixing cement and standard sand in the proportions of (A) 1 : 2 (B) 1 : 3 (C) 1 : 4 (D) 1 : 6

Last Answer : Answer: Option B

Pick up the correct statement from the following: (A) The plywoods do not split or crack due to changes in atmosphere (B) The commercial plywoods are available upto 150 cm wide and upto 300 cm long (C) The plywoods possess uniform tensile strength in all directions (D) All the above

Description : Pick up the correct statement from the following: (A) The plywoods do not split or crack due to changes in atmosphere (B) The commercial plywoods are available upto 150 cm wide and upto 300 cm long (C) The plywoods possess uniform tensile strength in all directions (D) All the above

Last Answer : Answer: Option D

The load required to produce a unit deflection in the spring is called (a) Modulus of Rigidity (b) Spring stiffness (c) Flexural rigidity (d) Tensional rigidity

Description : The load required to produce a unit deflection in the spring is called (a) Modulus of Rigidity (b) Spring stiffness (c) Flexural rigidity (d) Tensional rigidity

Last Answer : b) Spring stiffness

The load required to produce a unit deflection in the spring is called (a) Modulus of Rigidity (b) Spring stiffness (c) Flexural rigidity (d) Tensional rigidity

Description : The load required to produce a unit deflection in the spring is called (a) Modulus of Rigidity (b) Spring stiffness (c) Flexural rigidity (d) Tensional rigidity

Last Answer : (b) Spring stiffness

C.R.R.I. charts are used to obtain a relationship between strength of concrete and (A) Water cement ratio (B) Workability (C) Grading of aggregate (D) Fineness modulus

Description : C.R.R.I. charts are used to obtain a relationship between strength of concrete and (A) Water cement ratio (B) Workability (C) Grading of aggregate (D) Fineness modulus

Last Answer : Answer: Option A

Pick up the correct statement from the following: (A) Plain cement concrete is equally strong in compression as well as in tension (B) Slump test is performed to check concrete strength (C) Curing of concrete is done for proper compaction of cement (D) Fineness modulus is the index number expressing the relative sizes of both coarse and fine aggregates

Description : Pick up the correct statement from the following: (A) Plain cement concrete is equally strong in compression as well as in tension (B) Slump test is performed to check concrete strength (C ... D) Fineness modulus is the index number expressing the relative sizes of both coarse and fine aggregates

Last Answer : Option D

Consider the following statements: Percentage of steel for balanced designed of a singly reinforced rectangular section by limit state method depends on (1) Characteristic strength of concrete (2) Yield strength of concrete (3) Modulus of elasticity of steel (4) Geometry of the section. Which of these statements are correct? (a) 2, 3 and 4 (b) 1, 3 and 4 (c) 1, 2 and 4 (d) 1, 2 and 3

Description : Consider the following statements: Percentage of steel for balanced designed of a singly reinforced rectangular section by limit state method depends on (1) Characteristic strength of concrete (2) Yield strength of concrete (3) Modulus of elasticity ... (b) 1, 3 and 4 (c) 1, 2 and 4 (d) 1, 2 and 3

Last Answer : 1,2,4

As per IS: 456, permissible direct compressive stress M20 grade concrete in working stress method of designer [ A ] 5.0 N/mm2 [ B ] 7.0 N/mm2 [ C ] 10.0 N/mm2 [ D ] 20.0 N/mm2

Description : As per IS: 456, permissible direct compressive stress M20 grade concrete in working stress method of designer [ A ] 5.0 N/mm2 [ B ] 7.0 N/mm2 [ C ] 10.0 N/mm2 [ D ] 20.0 N/mm2

Last Answer : [ A ] 5.0 N/mm2

Permissible compressive strength of M 200 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 250 kg/cm2

Description : Permissible compressive strength of M 200 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 250 kg/cm2

Last Answer : (C) 200 kg/cm2

Permissible compressive strength of M 300 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 300 kg/cm2

Description : Permissible compressive strength of M 300 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 300 kg/cm2

Last Answer : (D) 300 kg/cm2

Permissible compressive strength of M 200 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 250 kg/cm2

Description : Permissible compressive strength of M 200 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 250 kg/cm2

Last Answer : Answer: Option C

Specified compressive strength of concrete is obtained from cube tests at the end of (A) 3 days (B) 7 days (C) 21 days (D) 28 day

Description : Specified compressive strength of concrete is obtained from cube tests at the end of (A) 3 days (B) 7 days (C) 21 days (D) 28 day

Last Answer : Answer: Option D

Permissible compressive strength of M 150 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 250 kg/cm2

Description : Permissible compressive strength of M 150 concrete grade is (A) 100 kg/cm2 (B) 150 kg/cm2 (C) 200 kg/cm2 (D) 250 kg/cm2

Last Answer : Answer: Option C

In limit state design of concrete for flexure, the area of stress block is taken as (a) 0.530 fck. Xu (b) 0.446 fck . Xu ( c) 0.420 fck .Xu (d) 0.360 fck . Xu Where fck is characteristic compressive strength of concrete and Xu is the depth of neutral axis from top.

Description : In limit state design of concrete for flexure, the area of stress block is taken as (a) 0.530 fck. Xu (b) 0.446 fck . Xu ( c) 0.420 fck .Xu (d) 0.360 fck . Xu Where fck is characteristic compressive strength of concrete and Xu is the depth of neutral axis from top.

Last Answer : (d) 0.360 fck . Xu

Interior thickness of concrete road slab for design wheel load 6300 kg and permissible flexural stress 21 kg/cm2 , is (A) 17.0 cm (B) 25.5 cm (C) 34.0 cm (D) 42.5 cm

Description : Interior thickness of concrete road slab for design wheel load 6300 kg and permissible flexural stress 21 kg/cm2 , is (A) 17.0 cm (B) 25.5 cm (C) 34.0 cm (D) 42.5 cm

Last Answer : Answer: Option B

Which of the following mechanical properties of a material is most structure insensitive? (A) Modulus of elasticity (young's modulus) (B) Toughness (C) Percentage reduction of area (D) Tensile strength

Description : Which of the following mechanical properties of a material is most structure insensitive? (A) Modulus of elasticity (young's modulus) (B) Toughness (C) Percentage reduction of area (D) Tensile strength

Last Answer : (A) Modulus of elasticity (young's modulus)

Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Description : Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Last Answer : (c) endurance limit to the working stress

The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Description : The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Last Answer : (d) endurance limit

The ability of a material to resist plastic deformation known as _____________ a) Tensile strength b) Yield strength c) Modulus of elasticity d) Impact strength

Description : The ability of a material to resist plastic deformation known as _____________ a) Tensile strength b) Yield strength c) Modulus of elasticity d) Impact strength

Last Answer : b) Yield strength

Fatigue resistance of a material is measured by the (A) Elastic limit (B) Ultimate tensile strength (C) Young's modulus (D) Endurance limit

Description : Fatigue resistance of a material is measured by the (A) Elastic limit (B) Ultimate tensile strength (C) Young's modulus (D) Endurance limit

Last Answer : (D) Endurance limit