Description : Extreme Pressure (EP) additives cause ______ wear in the bearing parts. (a) abrasive (b) corrosive (c) pitting (d) fatigue
Last Answer : (b) corrosive
Description : Extreme pressure causes ______ wear in the bearing parts. a) Abrasive b) Corrosive c) Pitting d) All of the mentioned
Last Answer : b) Corrosive
Description : Silicon carbide is a/an (A) Adhesive (B) Abrasive (C) Type of glass (D) Brittle material
Last Answer : (B) Abrasive
Description : The property of the bearing material to allow the dust and abrasive particles to get absorbed on the surface of the lining is called (A) Embeddability (B) Conformability (C) Viscosity (D) Endurance limit stress
Last Answer : (A) Embeddability
Description : Deformation that occurs due to stress over a period of time is known as ____________ a) Wear resistance b) Fatigue c) Creep d) Fracture
Last Answer : c) Creep
Description : Which of the following statement(s) is/are true concerning ischemia reperfusion injury? a. During ischemia, ATP degradation results in increased plasma and intracellular levels of ... immunization with antibodies to neutrophil adhesive complex lessen the ischemic/reperfusion microvascular injury
Last Answer : Answer: a, b, c, d During the ischemia and hypoperfusion phase, degradation of ATP stores essential to maintain cell integrity and significant loss of diffusible ... either the neutrophil adhesive complex or the endothelial selectins dramatically lessens ischemia/reperfusion microvascular injury
Description : In patients with exposed root surfaces: A. Ask to use low abrasive dentifrices B. It is because of dental hypersensitivity
Last Answer : A. Ask to use low abrasive dentifrices
Description : The shear resistance of a soil is constituted basically of the following component. (A) The frictional resistance to translocation between the individual soil particles at their contact point (B) To the ... (C) Cohesion and adhesion between the surfaces of the soil particles (D) All the above
Last Answer : Answer: Option D
Description : A thick film bearing is a bearing (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant (B) Where the surfaces of journal and the bearing are partially ... are separated by a film created by elastic deflection of parts (D) Where there is no lubricant
Last Answer : (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant
Description : For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like ... be elastic deformation of the parts in contact (D) There should be metal to metal contact
Last Answer : (C) There should be elastic deformation of the parts in contact
Description : For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact
Last Answer : (B) There should be external source like pump to supply lubricant under pressure
Description : For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact
Last Answer : (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space
Description : A thin film bearing is a bearing (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant (B) Where the surfaces of journal and the bearing are partially ... are separated by a film created by elastic deflection of parts (D) Where there is no lubricant
Last Answer : (B) Where the surfaces of journal and the bearing are partially separated by a film of lubricant and there is partial metal to metal contact
Description : A zero film bearing is a bearing (A) Where the surfaces of journal and the bearing are separated by a thick film of lubricant (B) Where the surfaces of journal and the bearing are partially ... bearing are separated by a film created by elastic deflection of parts (D) Where there is no lubricant
Last Answer : (D) Where there is no lubricant
Description : Thick film lubrication describes a phenomenon where two surfaces are _______ separated. a) Completely b) Partially c) Not d) None of the mentioned
Last Answer : a) Completely
Description : A fillet weld is an approximately triangular cross section joining two surfaces lying parallels to each other. a) True b) False
Last Answer : b) False
Description : Cast surfaces have good finishing. a) True b) False
Description : Surface tension of liquids is the result of which the following: w) interaction of a liquid with its container x) unbalanced forces on the liquid's surface molecules y) adhesive forces of the liquid z) interaction of the liquid's surface molecules and the applied pressure
Last Answer : ANSWER: X -- UNBALANCED FORCES ON THE LIQUID'S SURFACE MOLECULES
Description : Trinitrotoluene is – (1) used to melt metals (2) used to fuse two metals (3) used as an abrasive (4) used as an explosive
Last Answer : (4) used as an explosive Explanation: Trinitrotoluene (C6H2 (NO2)3.CH3), abbreviated as TNT, is sometimes used as a reagent in chemical synthesis, but it is best known as an explosive material ... The explosive yield of TNT is considered to be the standard mea-sure of bombs and other explosives.
Description : The damage/deterioration of metals by the __________ action of fluids is called 'erosion'. (A) Abrasive (B) Corrosive (C) Both (A) & (B) (D) Neither (A) nor (B)
Last Answer : (A) Abrasive
Description : Trinitrotoluene is (1) used to melt metals (2) used to fuse two metals (3) used as an abrasive (4) used as an explosive
Last Answer : used as an explosive
Description : Under complex loading, if elastic limit reaches in tension, then failure occurs due to (a) Firstly Maximum principal strain theory (b) Secondly Maximum principal theory of strain energy (c) Thirdly Maximum Principal stress theory (d) None
Last Answer : (c) Thirdly Maximum Principal stress theory
Description : Under complex loading, if elastic limit reaches in tension, then failure occurs due to (a) Firstly Maximum principal strain theory (b) Secondly Maximum principal theory of strain energy (c) Thirdly Maximum shear stress theory (d) None
Last Answer : (d) None
Description : How do gradient affects a streams erosive energy?
Last Answer : Need answer
Description : The greatest erosive power of a river is associated with – (1) gorges (2) meanders (3) inter-locking spurs (4) V-shaped valley
Last Answer : (2) meanders Explanation: Erosive power of a stream is proportional to the square of the velocity. Thus, when discharge increases, the depth increases and the velocity increases, resulting in dramatic ... on the outer bank erodes a deeper channel. The result of all these actions is a meander
Description : What is the significance of erosive lichen planus:** A. High malignant potential B. Some malignant potential
Last Answer : B. Some malignant potential
Description : The greatest erosive power of a river is associated with (1) gorges (2) meanders (3) inter-locking spurs (4) V-shaped valley
Last Answer : meanders
Description : Which of the following statements is/are true for coulomb damping? 1. Coulomb damping occurs due to friction between two lubricated surfaces2. Damping force is opposite to the direction of motion of vibrating body ... 2, 3 and statement 4 c. Only statement 2 d. All the above statements are true
Last Answer : c. Only statement 2
Last Answer : When a bogie negotiates a curve, reduction in adhesion occurs resulting in sliding. Thus sliding is acute when wheel base of axles is more, degree of curvature is more.
Description : Sliding contact bearings, also called plain bearings have no problem of wear. a) True b) False
Description : _____ is a surface fatigue failure which occurs when the load on the bearing part exceeds the surface endurance strength of the material. (a) Scoring (b) Pitting (c) Corrosion
Last Answer : (b) Pitting
Description : Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension. a) True b) False
Description : For a parallel load on a fillet weld of equal legs, the plane of maximum shear occurs at (a) 22.5° (b) 30° (c) 45° (d) 60°
Last Answer : (c) 45°
Description : In sunk key no slips occurs A. True B. False
Last Answer : A. True
Description : The removal of paint from electrical equipment, such as generators, should be cautiously undertaken because ____________. A. the mechanical shock of paint removal lessens the dielectric strength ... phase windings frequently become isolated from each other due to dust interference at the terminals
Last Answer : Answer: B
Description : A coal with high ash content is undesirable, as (A) It is abrasive to the coal pulveriser (i.e. ball mill) and the combustion chamber (B) The ash in molten condition gets absorbed in the pores of the ... and stick to the boiler tubes thereby reducing the heat transfer (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : A solid needle placed horizontally on the surface of the water floats due to (a) Surface tension (b) Capillary action (c) Cohesion (d) Adhesion
Last Answer : Ans:(a)
Description : Cell recognition and adhesion occur due to biochemicals of cell membrane named (a) Proteins (b) Lipids (c) Proteins and lipids (d) Glycoproteins and glycolipids
Last Answer : Ans:(d)
Description : Cell recognition and adhesion occur due to biochemicals of cell membranes named (a) proteins (b) lipids (c) proteins and lipids (d) glycoproteins and glycolipids.
Last Answer : (d) glycoproteins and glycolipids.
Description : The fluid property, due to which, mercury does not wet the glass is (A) Surface tension (B) Viscosity (C) Cohesion (D) Adhesion
Last Answer : (A) Surface tension
Description : Rise of liquid in a capillary tube is due to (A) Cohesion (B) Adhesion (C) Both (A) & (B) (D) Neither (A) nor (B)
Last Answer : (C) Both (A) & (B
Description : The mercury does not wet the glass. This is due to the property of the liquid known as (A) Cohesion (B) Adhesion (C) Viscosity (D) Surface tension
Description : Mercury does not wet glass. This is due to property of liquid known as (A) Adhesion (B) Cohesion (C) Surface tension (D) Viscosity
Last Answer : Answer: Option C
Description : Falling drops of water become spheres due to the property of (A) Adhesion (B) Cohesion (C) Surface tension (D) Viscosity
Description : Free surface of a liquid behaves like a sheet and tends to contract to smallest possible area due to the (A) Force of adhesion (B) Force of cohesion (C) Force of friction (D) Force of diffusion
Last Answer : Answer: Option B
Description : Capillary action is due to the (A) Surface tension (B) Cohesion of the liquid (C) Adhesion of the liquid molecules and the molecules on the surface of a solid (D) All of the above
Description : The tendency of a liquid surface to contract is due to the following property (A) Cohesion (B) Adhesion (C) Viscosity (D) Surface tension
Description : During maintenance of circuit breakers, _______________. A. always smooth roughened contact surfaces with a file B. never pass more than rated breaker current through the overload heater element C. ... wear and misalignment of main contacts D. assume heater elements installed are of correct size
Last Answer : Answer: C