Extreme Pressure (EP) additives cause ______ wear in the bearing parts. (a) abrasive (b) corrosive (c) pitting (d) fatigue

Extreme Pressure (EP) additives cause ______ wear in the bearing parts.

(a) abrasive

(b) corrosive

(c) pitting

(d) fatigue
by

1 Answer

Answer :

(b) corrosive
by

Related questions

Extreme pressure causes ______ wear in the bearing parts. a) Abrasive b) Corrosive c) Pitting d) All of the mentioned

Description : Extreme pressure causes ______ wear in the bearing parts. a) Abrasive b) Corrosive c) Pitting d) All of the mentioned

Last Answer : b) Corrosive

_____ is a surface fatigue failure which occurs when the load on the bearing part exceeds the surface endurance strength of the material. (a) Scoring (b) Pitting (c) Corrosion

Description : _____ is a surface fatigue failure which occurs when the load on the bearing part exceeds the surface endurance strength of the material. (a) Scoring (b) Pitting (c) Corrosion

Last Answer : (b) Pitting

The property of the bearing material to allow the dust and abrasive particles to get absorbed on the surface of the lining is called (A) Embeddability (B) Conformability (C) Viscosity (D) Endurance limit stress

Description : The property of the bearing material to allow the dust and abrasive particles to get absorbed on the surface of the lining is called (A) Embeddability (B) Conformability (C) Viscosity (D) Endurance limit stress

Last Answer : (A) Embeddability

What type of wear occurs due to an interaction of surfaces due to adhesion of the metals? a) Adhesive wear b) Abrasive wear c) Fretting wear d) Erosive wear

Description : What type of wear occurs due to an interaction of surfaces due to adhesion of the metals? a) Adhesive wear b) Abrasive wear c) Fretting wear d) Erosive wear

Last Answer : a) Adhesive wear

Stress concentration is caused due to A. Variation in properties of material from point to point in a member B. Pitting at points or areas at which loads on a member are applied C. Abrupt change of section D. All of the above

Description : Stress concentration is caused due to A. Variation in properties of material from point to point in a member B. Pitting at points or areas at which loads on a member are applied C. Abrupt change of section D. All of the above

Last Answer : D. All of the above

Deformation that occurs due to stress over a period of time is known as ____________ a) Wear resistance b) Fatigue c) Creep d) Fracture

Description : Deformation that occurs due to stress over a period of time is known as ____________ a) Wear resistance b) Fatigue c) Creep d) Fracture

Last Answer : c) Creep

For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For elasto-hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (C) There should be elastic deformation of the parts in contact

For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrostatic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (B) There should be external source like pump to supply lubricant under pressure

For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to supply lubricant under pressure (C) There should be elastic deformation of the parts in contact (D) There should be metal to metal contact

Description : For hydrodynamic lubrication (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space (B) There should be external source like pump to ... be elastic deformation of the parts in contact (D) There should be metal to metal contact

Last Answer : (A) There should be relative motion between the surfaces of the journal and the bearing and wedge shaped clearance space

The damage/deterioration of metals by the __________ action of fluids is called 'erosion'. (A) Abrasive (B) Corrosive (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : The damage/deterioration of metals by the __________ action of fluids is called 'erosion'. (A) Abrasive (B) Corrosive (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (A) Abrasive

A journal bearing is a ______ contact bearing working on the hydrodynamic lubrication and which supports load in____ direction. a) Sliding, Axial b) Rolling, Radial c) Sliding, Radial d) Rolling, Axial

Description : A journal bearing is a ______ contact bearing working on the hydrodynamic lubrication and which supports load in____ direction. a) Sliding, Axial b) Rolling, Radial c) Sliding, Radial d) Rolling, Axial

Last Answer : c) Sliding, Radial

Which one of the following parts of a ball bearing acts as a barrier between the balls preventing them from bumping into each other? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Description : Which one of the following parts of a ball bearing acts as a barrier between the balls preventing them from bumping into each other? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Last Answer : (d) Cage

Which one of the following parts of a ball bearing is mounted to the housing and is stationary? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Description : Which one of the following parts of a ball bearing is mounted to the housing and is stationary? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Last Answer : (b) Outer race

Which one of the following parts of a ball bearing is mounted on the rotating shafts and tends to rotate the shaft? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Description : Which one of the following parts of a ball bearing is mounted on the rotating shafts and tends to rotate the shaft? (a) Inner race (b) Outer race (c) Rolling element (d) Cage

Last Answer : (a) Inner race

A thick film bearing is a bearing (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant (B) Where the surfaces of journal and the bearing are partially separated by a film of lubricant and there is partial metal to metal contact (C) Where the surfaces of journal and the bearing are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Description : A thick film bearing is a bearing (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant (B) Where the surfaces of journal and the bearing are partially ... are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Last Answer : (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant

A thin film bearing is a bearing (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant (B) Where the surfaces of journal and the bearing are partially separated by a film of lubricant and there is partial metal to metal contact (C) Where the surfaces of journal and the bearing are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Description : A thin film bearing is a bearing (A) Where the surfaces of journal and the bearing are completely separated by a film of lubricant (B) Where the surfaces of journal and the bearing are partially ... are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Last Answer : (B) Where the surfaces of journal and the bearing are partially separated by a film of lubricant and there is partial metal to metal contact

A zero film bearing is a bearing (A) Where the surfaces of journal and the bearing are separated by a thick film of lubricant (B) Where the surfaces of journal and the bearing are partially separated by a film of lubricant and there is partial metal to metal contact (C) Where the surfaces of journal and the bearing are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Description : A zero film bearing is a bearing (A) Where the surfaces of journal and the bearing are separated by a thick film of lubricant (B) Where the surfaces of journal and the bearing are partially ... bearing are separated by a film created by elastic deflection of parts (D) Where there is no lubricant

Last Answer : (D) Where there is no lubricant

Which of the following is not a function of washer? a) Distributes load over a large area of clamped parts b) Provides bearing surface over large clearance bolts c) Prevents marring of the bolt head and nut surface d) Helps in locking of the fastener

Description : Which of the following is not a function of washer? a) Distributes load over a large area of clamped parts b) Provides bearing surface over large clearance bolts c) Prevents marring of the bolt head and nut surface d) Helps in locking of the fastener

Last Answer : d) Helps in locking of the fastener

Scoring is a ________ phenomenon. (a) stick-slip (b) fracture (c) fatigue (d) in-out

Description : Scoring is a ________ phenomenon. (a) stick-slip (b) fracture (c) fatigue (d) in-out

Last Answer : (a) stick-slip

Scoring is a ________ phenomenon. a) Stick-slip b) Fracture c) Fatigue d) In-out

Description : Scoring is a ________ phenomenon. a) Stick-slip b) Fracture c) Fatigue d) In-out

Last Answer : a) Stick-slip

Propagation of fatigue failure is always due to compressive stresses. a) Due to bending b) Due to tensile c) Due to fatigue d) None of the listed

Description : Propagation of fatigue failure is always due to compressive stresses. a) Due to bending b) Due to tensile c) Due to fatigue d) None of the listed

Last Answer : b) Due to tensile

What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping

Description : What will happen if stresses induced due to surge in the spring exceeds the endurance limit stress of the spring. a) Fatigue Failure b) Fracture c) None of the listed d) Nipping

Last Answer : a) Fatigue Failure

The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by external cyclic load (C) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three

Description : The connecting rod bolts are tightened up with the initial tension greater than external load so that (A) Failure of bolt will be static (B) The resultant load on bolt will not be affected by ... ) The bolt will not fail by fatigue although the external load is fluctuating (D) All the three

Last Answer : (D) All the three

When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65

Description : When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65

Last Answer : (c) 0.50

Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Description : Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Last Answer : (c) endurance limit to the working stress

The yield point in static loading is ............... as compared to fatigue loading. (a) higher (b) lower (c) same

Description : The yield point in static loading is ............... as compared to fatigue loading. (a) higher (b) lower (c) same

Last Answer : (a) higher

The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Description : The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Last Answer : (d) endurance limit

Failure of a material is called fatigue when it fails (a) at the elastic limit (b) below the elastic limit (c) at the yield point (d) below the yield point

Description : Failure of a material is called fatigue when it fails (a) at the elastic limit (b) below the elastic limit (c) at the yield point (d) below the yield point

Last Answer : (d) below the yield point

The endurance or fatigue limit is defined as the maximum value of the stress which a polished standard specimen can withstand without failure, for infinite number of cycles, when subjected to (a) static load (b) dynamic load (c) static as well as dynamic load (d) completely reversed load

Description : The endurance or fatigue limit is defined as the maximum value of the stress which a polished standard specimen can withstand without failure, for infinite number of cycles, when subjected to (a) static load (b) dynamic load (c) static as well as dynamic load (d) completely reversed load

Last Answer : (d) completely reversed load

Does ASME Standard take into consideration shock and fatigue factors? a) Yes b) No

Description : Does ASME Standard take into consideration shock and fatigue factors? a) Yes b) No

Last Answer : a) Yes

Does ASME Standard take into consideration shock and fatigue factors? a) Yes b) No

Description : Does ASME Standard take into consideration shock and fatigue factors? a) Yes b) No

Last Answer : a) Yes

The relationship between the alternating stress and mean stress is given by the following equation: σ a =σ e [1-(σ m /σ u )x], where σ e is the fatigue limit for completely reversed loading. The value of x for Gerber line is equal to _________ a) 1 b) 2 c) 0.5 d) -1

Description : The relationship between the alternating stress and mean stress is given by the following equation: σ a =σ e [1-(σ m /σ u )x], where σ e is the fatigue limit for completely reversed loading. The value of x for Gerber line is equal to _________ a) 1 b) 2 c) 0.5 d) -1

Last Answer : b) 2

Calculate fatigue stress concentration factor, when theoretical stress concentration factor is 1.62 and notch sensitivity is equal to 0.9 a. 1.558 b. 3.358 c. 1.162 d. None of the above

Description : Calculate fatigue stress concentration factor, when theoretical stress concentration factor is 1.62 and notch sensitivity is equal to 0.9 a. 1.558 b. 3.358 c. 1.162 d. None of the above

Last Answer : a. 1.558

In S-N diagram, the graph plotted between fatigue strength and number of stress cycles becomes horizontal for which type of materials? a. Ferrous materials b. Non-ferrous materials c. Both a. and b. d. None of the above

Description : In S-N diagram, the graph plotted between fatigue strength and number of stress cycles becomes horizontal for which type of materials? a. Ferrous materials b. Non-ferrous materials c. Both a. and b. d. None of the above

Last Answer : a. Ferrous materials

Notch sensitivity (q) is given by the equation _______ where K f = fatigue stress concentration factor and K t = theoretical stress concentration factor a. ( K f + 1 ) / ( K t – 1 ) b. ( K f – 1 ) / ( K t – 1 ) c. ( K f + 1 ) / ( K t + 1 ) d. ( K f - 1 ) / ( K t + 1 )

Description : Notch sensitivity (q) is given by the equation _______ where K f = fatigue stress concentration factor and K t = theoretical stress concentration factor a. ( K f + 1 ) / ( K t – 1 ) b. ( K f – 1 ) / ( K t – 1 ) c. ( K f + 1 ) / ( K t + 1 ) d. ( K f - 1 ) / ( K t + 1 )

Last Answer : b. ( K f – 1 ) / ( K t – 1 )

There is sufficient plastic deformation prior to fatigue failure, which gives a warning well in advance. a) True b) False

Description : There is sufficient plastic deformation prior to fatigue failure, which gives a warning well in advance. a) True b) False

Last Answer : b) False

Fatigue failure is time dependent failure. a) True b) False

Description : Fatigue failure is time dependent failure. a) True b) False

Last Answer : a) True

The phenomenon of decreased resistance of the materials to fluctuating stresses is the main characteristic of _____ failure. a) Fracture b) Fatigue c) Yielding d) None of the mentioned

Description : The phenomenon of decreased resistance of the materials to fluctuating stresses is the main characteristic of _____ failure. a) Fracture b) Fatigue c) Yielding d) None of the mentioned

Last Answer : b) Fatigue

The ability of materials to develop a characteristic behavior under repeated loading known as ___________ a) Toughness b) Resilience c) Hardness d) Fatigue

Description : The ability of materials to develop a characteristic behavior under repeated loading known as ___________ a) Toughness b) Resilience c) Hardness d) Fatigue

Last Answer : d) Fatigue

The notch sensitivity q is expressed in terms of fatigue stress concentration factor Kf and theoretical stress concentration factor Kt as (A) (Kf + 1)/ (Kt + 1) (B) (Kf - 1)/ (Kt - 1) (C) (Kt + 1)/ (Kf + 1) (D) (Kt - 1)/ (Kf - 1)

Description : The notch sensitivity q is expressed in terms of fatigue stress concentration factor Kf and theoretical stress concentration factor Kt as (A) (Kf + 1)/ (Kt + 1) (B) (Kf - 1)/ (Kt - 1) (C) (Kt + 1)/ (Kf + 1) (D) (Kt - 1)/ (Kf - 1)

Last Answer : (B) (Kf - 1)/ (Kt - 1)

Assertion (A): Hydrostatic lubrication is more advantageous when compared to hydrodynamic lubrication during starting and stopping the journal in its bearing. Reason (R): In hydrodynamic lubrication, the fluid film pressure is generated by the rotation of the journal. [IES-1998] (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

Description : Assertion (A): Hydrostatic lubrication is more advantageous when compared to hydrodynamic lubrication during starting and stopping the journal in its bearing. Reason (R): In hydrodynamic lubrication, the fluid film pressure is ... (c) A is true but R is false (d) A is false but R is true

Last Answer : (b) Both A and R are individually true but R is not the correct explanation of A

Satisfactory hydrodynamic film in a journal bearing is formed when (a) Journal speed is low; unit pressure on the bearing is high and viscosity of lubricant used is low [IES-2006] (b) Journal speed is low; unit pressure on the bearing is low and viscosity of lubricant used is low (c) Journal speed is high; unit pressure on the bearing is high and viscosity of lubricant used is high (d) Appropriate combination of journal speed, unit pressure on bearing and lubricant viscosity exists resulting in low coefficient of friction

Description : Satisfactory hydrodynamic film in a journal bearing is formed when (a) Journal speed is low; unit pressure on the bearing is high and viscosity of lubricant used is low [IES-2006] ... journal speed, unit pressure on bearing and lubricant viscosity exists resulting in low coefficient of friction

Last Answer : (c) Journal speed is high; unit pressure on the bearing is high and viscosity of lubricant used is high

Which one of the following sets of parameters should be monitored for determining safe operation of journal bearing? [IES-2000] Oil pressure, bearing metal temperature and bearing vibration (b) Bearing vibration, oil pressure and speed of shaft (c) Bearing metal temperature and oil pressure (d) Oil pressure and bearing vibration

Description : Which one of the following sets of parameters should be monitored for determining safe operation of journal bearing? [IES-2000] Oil pressure, bearing metal temperature and bearing vibration (b) ... shaft (c) Bearing metal temperature and oil pressure (d) Oil pressure and bearing vibration

Last Answer : Oil pressure, bearing metal temperature and bearing vibration

A full journal bearing having clearance to radius ratio of 1/100, using a lubricant with μ=28×10-3 Pa s supports the shaft journal running at N = 2400 rpm If bearing pressure is 1.4 MPa, the Somerfield number is [IES-2001] (a) 8×10-3 (b) 8×10-5 (c) 0.48 (d) 0.48×10

Description : A full journal bearing having clearance to radius ratio of 1/100, using a lubricant with μ=28×10-3 Pa s supports the shaft journal running at N = 2400 rpm If bearing pressure is 1.4 MPa, the Somerfield number is [IES-2001] (a) 8×10-3 (b) 8×10-5 (c) 0.48 (d) 0.48×10

Last Answer : (a) S = (μN s /p) (r/c) 2

The bearing characteristic number in a hydrodynamic bearing depends on- (a) Length, width and load (b) length, width and speed. [IES-1996] (c) Viscosity, speed and load (d) viscosity, speed and bearing pressure.

Description : The bearing characteristic number in a hydrodynamic bearing depends on- (a) Length, width and load (b) length, width and speed. [IES-1996] (c) Viscosity, speed and load (d) viscosity, speed and bearing pressure.

Last Answer : (d) viscosity, speed and bearing pressure.

Consider the following statements: [IES 2007] For a journal rotating in a bearing under film lubrication conditions, the frictional resistance is- 1. Proportional to the area of contact 2. Proportional to the viscosity of lubricant 3. Proportional to the speed of rotation 4. Independent of the pressure Which of the statements given above are correct? (a) 1, 2, 3 and 4 (b) 1 and 4 only (c) 2, 3 and 4 only (d) 2 and 3 only

Description : Consider the following statements: [IES 2007] For a journal rotating in a bearing under film lubrication conditions, the frictional resistance is- 1. Proportional to the area of contact 2. Proportional to the viscosity of lubricant 3. ... 4 (b) 1 and 4 only (c) 2, 3 and 4 only (d) 2 and 3 only

Last Answer : (a) 1, 2, 3 and 4

Assertion (A): In steady rotating condition the journal inside a hydrodynamic journal bearing remains floating on the oil film. [IES-2008] Reason (R): The hydrodynamic pressure developed in steady rotating conditions in journal bearings balances the load on the journal. (a) Both A and R are true and R is the correct explanation of A (b) Both A and R are true but R is NOT the correct explanation of A (c) A is true but R is false (d) A is false but R is true

Description : Assertion (A): In steady rotating condition the journal inside a hydrodynamic journal bearing remains floating on the oil film. [IES-2008] Reason (R): The hydrodynamic pressure developed in steady rotating conditions in journal ... A (c) A is true but R is false (d) A is false but R is true

Last Answer : (a) Both A and R are true and R is the correct explanation of A

Petroff’s equation is used to find out (A) Load carrying capacity of the bearing (B) Frictional losses in the bearing (C) Unit bearing pressure on the bearing (D) Pressure distribution around the periphery of the journal

Description : Petroff’s equation is used to find out (A) Load carrying capacity of the bearing (B) Frictional losses in the bearing (C) Unit bearing pressure on the bearing (D) Pressure distribution around the periphery of the journal

Last Answer : (B) Frictional losses in the bearing