Description : Counter shaft is a secondary shaft. a) True b) False
Last Answer : a) True
Description : Assertion (A): In anti-friction bearings, the frictional resistance is very low as the shaft held by it remains in floating condition by the hydrodynamic pressure developed by the lubricant. [IES-2006] Reason (R): In hydrodynamic ... of A (c) A is true but R is false (d) A is false but R is true
Last Answer : (d) A is false but R is true
Description : A total permanent deformation of 0.0001 of the ball diameter is taken for considering static load capacity of the shaft. a) True b) False
Description : A radial bearing supports the load that acts along the axis of the shaft. a) True b) False
Last Answer : b) False
Description : The hub is treated as a solid shaft while calculating torsional shear stress in the hub. a) True b) False
Description : Solid shaft is costlier than hollow shaft of same weight. a) True b) False
Description : The strength of hollow shaft is more than the strength of solid shaft of same weight. a) True b) False
Description : The stiffness of solid shaft is more than the stiffness of hollow shaft with same weight. a) True b) False
Description : Hot rolling produces a stronger shaft then cold rolling. a) True b) False
Description : Shaft is rotating machine element. A. True B. False
Last Answer : A. True
Description : Which of the following are not true for petroff’s equation? a) Shaft is considered concentric with the bearing b) Bearing is subjected to light load c) Is used to find coefficient of friction d) Frictional torque is given by fpr2l
Last Answer : d) Frictional torque is given by fpr2l
Description : It is a secondary shaft used to counter the direction of main shaft. 81. Shafts are subjected to ______ forces. a) Compressive b) Tensile c) Shear d) twisting
Last Answer : b) Tensile
Description : Counter shaft is a--------------- shaft. a) secondary b) first c) second d) primary
Last Answer : a) secondary
Description : In vehicle flywheel is place between 1. clutch and propeller shaft 2. engine and clutch 3. before engine 4. propeller shaft and differential
Last Answer : 2. engine and clutch
Description : The hub diameter of the flywheel is taken as 1. 2.5(shaft diameter) 2. 1.5(shaft diameter) 3. 4(shaft diameter) 4. 2(shaft diameter)
Last Answer : 4. 2(shaft diameter)
Description : In vehicles, flywheel is placed in between (A) Engine and clutch (B) Clutch and Propeller shaft (C) Propeller shaft and Differential (D) Before engine
Last Answer : (A) Engine and clutch
Description : The hub diameter of the flywheel is taken as, (A) 2.5 (shaft diameter) (B) 1.5 (shaft diameter) (C) 4 (shaft diameter) (D) 2 (shaft diameter)
Last Answer : (D) 2 (shaft diameter)
Description : The ball bearing is subjected to a radial load of 4000 N. Expected life for 90% bearings is 9000 hr and the shaft is rot (a) 42.21 kN (b) 37.29 kN (c) 26.33 kN (d) 35.22 kN
Last Answer : (b) 37.29 kN
Description : Calculate the bearing life if expected life for 90% bearings is 9000 hr and the shaft is rotating at 1500 rpm. (a) 850 million rev (b) 810 million rev (c) 810 hr (d) 850 hr
Last Answer : (b) 810 million rev
Description : The static load is defined as the load acting on the bearing when the shaft is _____. (a) stationary (b) rotating at rpm
Last Answer : (a) stationary
Description : Which one of the following parts of a ball bearing is mounted on the rotating shafts and tends to rotate the shaft? (a) Inner race (b) Outer race (c) Rolling element (d) Cage
Last Answer : (a) Inner race
Description : The rolling contact bearings as compared to sliding contact bearings have (a) small overall dimensions (b) accuracy of shaft alignment (c) low starting and low running friction except at very high speeds (d) all the mentioned
Last Answer : (d) all the mentioned
Description : Consider the following pairs of types of bearings and applications: 1. Partial Journal bearing................... Rail wagon axles 2. Full journal bearing ......................Diesel engine crank-shaft 3. Radial bearing ... matched? [IES-2000] (a) 1 alone (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3
Last Answer : (b) 1 and 2
Description : Which one of the following sets of parameters should be monitored for determining safe operation of journal bearing? [IES-2000] Oil pressure, bearing metal temperature and bearing vibration (b) ... shaft (c) Bearing metal temperature and oil pressure (d) Oil pressure and bearing vibration
Last Answer : Oil pressure, bearing metal temperature and bearing vibration
Description : A full journal bearing having clearance to radius ratio of 1/100, using a lubricant with μ=28×10-3 Pa s supports the shaft journal running at N = 2400 rpm If bearing pressure is 1.4 MPa, the Somerfield number is [IES-2001] (a) 8×10-3 (b) 8×10-5 (c) 0.48 (d) 0.48×10
Last Answer : (a) S = (μN s /p) (r/c) 2
Description : Consider tile following statements: [IES-1993; 2002; 2006] Radius of friction circle for a journal bearing depends upon 1. Coefficient of friction 2. Radius of the journal 3. Angular speed of rotation of the shaft Which of the ... ) 1,2 and 3 (b) Only 1 and 2 (c) Only 2 and 3 (d) Only 1 and 3
Last Answer : (b) Only 1 and 2
Description : Increase in values of which of the following results in an increase of the coefficient of friction in a hydrodynamic bearing? [IES 2007] 1. Viscosity of the oil. 2. Clearance between shaft and bearing. 3. Shaft speed. Select the ... 1 and 2 only (b) 1 and 3 only (c) 2 and 3 only (d) 1, 2 and 3
Last Answer : (b) 1 and 3 only
Description : In hydrodynamic bearing, when the shaft begins to rotate in clockwise direction, (A) The journal climbs to the right side of the bearing without metal to metal contact (B) The journal climbs to the left ... sinks down to the bottom of the bearing (D) The journal is at the center of the bearing
Last Answer : (A) The journal climbs to the right side of the bearing without metal to metal contact
Description : Static load is defined as the load acting on the bearing when shaft is _____ a) Stationary b) Rotating at rpm
Last Answer : a) Stationary
Description : A_______ bearing supports the load acting along the axis of the shaft. a) Thrust b) Radial c) Longitudinal d) Transversal
Last Answer : a) Thrust
Description : Which of the following are functions of bearings? a) Ensure free rotation of shaft with minimum friction b) Holding shaft in a correct position c) Transmit the force of the shaft to the frame d) All of the listed
Last Answer : d) All of the listed
Description : If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed
Last Answer : a) M/2πtr2
Description : If shaft diameter is 30mm and number of pins emplaced are 6, then the diameter of the pin will be? a) 6.4mm b) 5.6mm c) 6.1mm d) 5.9mm
Last Answer : c) 6.1mm
Description : If shaft diameter is 60mm, how many bolts are recommended for rigid flange coupling? a) 2 b) 3 c) 4 d) 5
Last Answer : c) 4
Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm
Last Answer : a) 27mm
Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed
Last Answer : c) 41666.7N
Description : If shaft diameter is 40mm, calculate the length of sleeves in clamp coupling. a) 80mm b) 140mm c) 100mm d) 120mm
Last Answer : b) 140mm
Description : If shaft diameter is 40mm, calculate the diameter of sleeves in clamp coupling. a) 100mm b) 80mm c) 60mm d) 40mm
Last Answer : a) 100mm
Description : Does shaft has to be shifted i axial direction to remove clamp coupling. a) Yes b) No
Last Answer : b) No
Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed
Last Answer : b) 51.6N/mm2
Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed
Last Answer : b) 25.8N/mm2
Description : Determine the length of kennedy key required to transmit 1200N-m and allowable shear in the key is 40N/mm2. The diameter of shaft and width of key can be taken as 40mm and 10mm respectively. a) 49mm b) 36mm c) 46mm d) 53mm
Last Answer : d) 53mm
Description : Woodruff key permits _____ movement b/w shaft and the hub. a) Axial b) Radial c) Eccentric d) None of the listed
Last Answer : b) Radial
Description : Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm2. a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm
Last Answer : b) 41.2mm
Description : While designing shaft on the basis of torsional rigidity, angle of twist is given by? a) Ml/Gd4 b) 584Ml/Gd4 c) 292 Ml/Gd4 d) None of the mentioned
Last Answer : b) 584Ml/Gd4