Description : Compare detonation and diesel knock on the basis of (i) Fuel Ignition Temperature (ii) Compression Ratio (iii) Speed (iv) inlet temperature (v) inlet pressure (vi) cylinder wall temperature (vii) cylinder size
Last Answer : Comparison between detonation and diesel knock: Parameter To avoid Detonation in SI Engine To avoid Diesel knock i) Fuel Ignition Temperature High Low ii) Compression Ratio ... Cylinder wall temperature Low High viii) Cylinder size Small Large
Description : For the complex [Fe(en)2Cl2], Cl, (en = ethylene diamine), identify (i) the oxidation number of iron, (ii) the hybrid orbitals and the shape of the complex, (iii) the magnetic behaviour of the complex, (iv) ... an optical isomer also, and (vi) name of the complex. (At. no. of Fe = 26) \ -Chemistry
Last Answer : i) [Fe(en)2Cl2] Cl or x + 0 + 2 (-1) + (-1) = 0 x + (- 3) = 0 or x = + 3 ∴ Oxidation number of iron, x = + 3 (ii) The complex has two bidentate ligands and two ... )2Cl2] Cl, only cis-isomer shows optical isomerism. (vi) Name of complex: Dichloridobis (ethane-1, 2- diamine) Iron (III) chloride
Description : Identify the components labelled A, B, C and D in the diagram below from the list (i) to (viii) given along with Components : (i) Cristae of mitochondria (ii) Inner membrane of mitochondria (iii) Cytoplasm (iv) Smooth endoplasmic ... viii) (vi) (c) (vi) (v) (iv) (vii) (d) (v) (i) (iii) (ii)
Last Answer : (a) (v) (iv) (viii) (iii)
Description : Identify type of BJT configuration having following features : (i) BJT configuration having the least current gain. (ii) KIT configuration called as voltage follower. (iii) BJT ... configuration suitable for voltage amplification. (vi) BJT configuration having the least output impedance.
Last Answer : (i) BJT configuration having the least current gain : Common Base Configuration (ii) KIT configuration called as voltage follower: Common Collector Configuration (iii) BJT ... Emitter Configuration (vi) BJT configuration having the least output impedance: Common Collector Configuration
Description : Write type of chip formed with following factors. (i) High rake angle (ii) High cutting speed (iii) Small depth of cut (iv) Low cutting speed (v) Large depth of cut (vi) Low rake angle
Last Answer : (i) High rake angle : Continuous chips (ii) High cutting speed : Continuous chips (iii) Small depth of cut : Continuous chips (iv) Low cutting speed :Continuous chips with built up edge (v) ... cut : Continuous chips with built up edge (vi) Low rake angle :Continuous chips with built up edge
Description : Check whether the following are quadratic equations: (i) (x+ 1)2=2(x-3) (ii) x - 2x = (- 2) (3-x) (iii) (x - 2) (x + 1) = (x - 1) (x + 3) (iv) (x - 3) (2x + 1) = x (x + 5) (v) (2x - 1) (x - 3) = (x ... vi) x2 + 3x + 1 = (x - 2)2 (vii) (x + 2)3 = 2x(x2 - 1) (viii) x3 -4x2 -x + 1 = (x-2)3 -Maths 10th
Last Answer : this is the correct answer!
Description : I have some matchsticks set up like this: I + XI = X. If you do not know Roman numerals, here is a quick starter: I=1 II=2 III=3 IV=4 V=5 VI=6 VII=7 VIII=8 IX=9 X=10 XI=11 ... are told to move the minimum number of matchsticks to make the question correct. So, how many do you have to move? -Riddles
Last Answer : Most people would get to one move at the least, but the real answer is zero moves. If you rotate the whole question around 180 degrees, it will display this: X = IX + I
Description : In ΔABC and ΔDEF, AB = DE, AB || DE, BC = EF and BC || EF. Vertices A, B and C are joined to vertices D, E and F respectively (see Fig. 8.22). Show that (i) quadrilateral ABED is a parallelogram ( ... CF and AD = CF (iv) quadrilateral ACFD is a parallelogram (v) AC = DF (vi) ΔABC ≅ ΔDEF. -Maths 9th
Last Answer : . Solution: (i) AB = DE and AB || DE (Given) Two opposite sides of a quadrilateral are equal and parallel to each other. Thus, quadrilateral ABED is a parallelogram (ii) Again BC = EF and BC || EF ... (Given) BC = EF (Given) AC = DF (Opposite sides of a parallelogram) , ΔABC ≅ ΔDEF [SSS congruency]
Description : What percentage is (i) Rs 15 of Rs 120? (ii) 36 minutes of 2 hours? (iii) 8 hours of 2 days (iv) 160 metres of 4 km? (v) 175 mL of 1 litre? (vi) 25 paise of Rs 4? -Maths
Last Answer : answer:
Description : Find: (i) 25% of Rs 76 (ii) 20% of Rs 132 (iii) 7.5% of 600 m (iv) 313% of 90 km (v) 8.5% of 5 kg (vi) 20% of 12 litres -Maths
Description : Find: (i) 32% of 425 (ii) 1623% of 16 (iii) 6.5% of 400 (iv) 136% of 70 (v) 2.8% of 35 (vi) 0.6% of 45 -Maths
Description : Convert each of the following fraction into a percentage: (i) 47 100 (ii) 9 20 (iii) 3 8 (iv) 8 125 (v) 19 500 (vi) 4 15 (vii) 2 3 (viii) 1 3 5 -Maths
Last Answer : We have the following: (i) 47100=47100×100% = 47% (ii) 920=920×100% =9×5%= 45% (iii) 38=38×100% =3×252%=752%=3712% (iv) 8125=8125×100%=8×45%=325%=6.4% (v) ... ;203%=803%=2623% (vii) 23=23×100%=2003%=6623% (viii) 135=85=85×100%=(8×20)%=160%
Description : Convert each of the following into a fraction: (i) 32% (ii) 614% (iii) 2623% (iv) 120% (v) 6.25% (vi) 0.8% (vii) 0.06% (viii) 22.75% -Maths
Description : Evaluate each of the following: (i) (103)3 (ii) (98)3 (iii) (9.9)3 (iv) (10.4)3 (v) (598)3 (vi) (99)3 -Maths 9th
Description : Cold dil. `H_(2)SO_(4)` will completely dissolve : (i) Pb (ii) `Fe_(3)O_(4)` (iii) Fe (iv) Cu (v) Mg (vi) MgO (vii) `CoCO_(3)` (viii) `CuCO_(2)` (ix)
Last Answer : Cold dil. `H_(2)SO_(4)` will completely dissolve : (i) Pb (ii) `Fe_(3)O_(4)` (iii) Fe (iv) Cu (v) ... ) `CoCO_(3)` (viii) `CuCO_(2)` (ix) `SrCO_(3)`
Description : Cold conc. `HNO_(3)` will completely dissolve: (i) Pb (ii) `Pb_(3)O_(4)` (iii) Fe (iv) Sn (v) Mg (vi) MgO (vii) Hg (viii) Au (ix) Ag (x) Pt
Last Answer : Cold conc. `HNO_(3)` will completely dissolve: (i) Pb (ii) `Pb_(3)O_(4)` (iii) Fe (iv) Sn (v) Mg (vi) MgO (vii) Hg (viii) Au (ix) Ag (x) Pt
Description : (i) `NH_(3)` (ii) `N_(2)H_(4)` (iii) `HN_(3)` (iv) `PH_(3)` (v) `H_(2)S` (vi) `AsH_(3)` (vii) `SbH_(3)` (viii) `H_(2)Se` (ix) `H_(2)Te` Number of mole
Last Answer : (i) `NH_(3)` (ii) `N_(2)H_(4)` (iii) `HN_(3)` (iv) `PH_(3)` (v) `H_(2) ... lone pair of electrons on the central atom is present in pure s-orbital
Description : How many of following metals impart a characteristic colour to the Bunsen flame ? `(i) Na " " (ii) Li " " (iii) K " " (iv) Ba` `(v) Sr " " (vi) Mg " "
Last Answer : How many of following metals impart a characteristic colour to the Bunsen flame ? `(i) Na " " (ii) Li " " (iii) K ... ix) `Be " " (x )Ca " " (x i)Cu`
Description : Number of oxide orwesd among , (i) Cassiterite (ii) pyrolusite (iii) Kieserite (iv) Azurite (V) chromite (vi) siderite are.
Last Answer : Number of oxide orwesd among , (i) Cassiterite (ii) pyrolusite (iii) Kieserite (iv) Azurite (V) chromite (vi) siderite are.
Description : How many of the following are oxides ores (i) Carnalite (ii) Cuprite (iii) Cassiterite (iv) Chromite (v) Cinnabar (vi) Calamine (vii) Cerussite (Viii)
Last Answer : How many of the following are oxides ores (i) Carnalite (ii) Cuprite (iii) Cassiterite (iv) ... (vii) Cerussite (Viii) Chalocopyrite (ix) Chalcocite
Description : Differentiate between any five of the following. (i) Artery and vein (ii) Hard water and soft water (iii) E-mail and Snail mail (iv) Apes and monkey (v) Hydrostatics and hydrodynamics (vi) Comet and ... (vii) Barrage and dam (viii) Electron and hole (ix) Isobars and isotopes (x) Autopsy and biopsy
Last Answer : Answers: (i) Artery and vein: Arteries: Muscular blood vessels that carry blood away from the heart. All arteries, with the exception of the pulmonary and umbilical arteries, carry oxygenated blood ... to determine cause of death Biopsy: Removal and study of a tissue sample for diagnostic purposes
Description : Name the quantities which are measured by the following units. (i) Newton (ii) Joule (iii) Watt (iv) Volt (v) Light year (vi) Angstrom (vii) Acre-foot (viii) Becquerel (ix) Hertz (x) Cusec
Last Answer : Answers: (i) Force (ii) Work Energy (iii) Power of electricity (iv) Potential difference (v) Distance of stars and planets (vi) Length (vii) Volume (viii) Radioactivity (ix) Frequency (x) Rate of flow of water
Description : Which quantity do the following units measure: (i) Volt (ii) Coulomb (iii) Walt (iv) Ohm (v) Mho (vi) Ampere (vii) Dyne (viii) Celsius (ix) Joule (x) Calorie
Last Answer : Answers: (i) Voltage (ii) Charge of Electricity (iii) Power (iv) Resistance (v) Conductivity (vi) Current (vii) Force (viii) Temperature (ix) Energy (x) Heat
Description : Arrange the following steps to form a basic Engineering Process Model. i. Test ii. Design iii. Install iv. Specification v. Manufacture vi. Maintain a) 2, 4, 5, 1, 6, 3 b) 4, 2, 5, 1, 3, 6 c) 2, 4, 5, 1, 3, 6 d) 4, 2, 5, 1, 6, 3
Last Answer : a) 2, 4, 5, 1, 6, 3
Description : The figure given below depicts a diagrammatic sectional view of the human female reproductive system. Which set of three parts out of I-VI have been correctly identified? I II III V VI IV (a) (II) ... , (V) Uterus, (VI) Cervix (d) (I) Perimetrium, (II) Myometrium, (III) Fallopian tube
Last Answer : (b) (III) Infundibulum, (IV) Fimbriae, (V) Cervix
Description : Which of the following instruction is of logical instructions? i) CPL A ii) JC rel iii) DA A iv) ANL A, Rn v) RR A vi) CPL bit a) i, v b) v, iii, I c) iv, ii d) v, iii, ii
Last Answer : c) iv, i
Description : A company has to choose between two projects whose cash flows are as indicated below; Project 1: i. Investment - Rs. 15 Lakhs ii. Annual cost savings - Rs. 4 lakhs. iii. Bi-annual ... years xii. Salvage Value- 2 lakhs Which project should the company choose? The annual discount rate is 12
Last Answer : Year Project 1 Project 2 Outgo Saving NPV Outgo Saving NPV 0 15.0 0 =-15.0 14.0 0 = -14 1 0 4.0 = (4 / (1+.12)1 = 3.571 0.2 3.5 = (3.3 / (1+.12)1 = 2.95 2 0.5 4.0 = (3.5 / (1+.12)2 = 2.79 0.2 3.5 ... (1+.12)8 = 3.43 0.2 5.5 (3.5+2) = (5.3 / (1+.12)8 = 2.14 NPV = + 2.301 @12% = + 0.15
Description : Draw symbol of (i) Tray Dryer (ii) Plate column (iii) Packed column (iv) Jaw crusher (v) Strirrer (vi) Ball mill.
Last Answer : i)Tray dryer: ii)Plate column: iii)Packed column: iv) Jaw crusher: v) Stirrer: vi) Ball mill
Description : Write the suitable cutter for carrying following operations on milling machine (i) Gear Tooth (ii) Parting off (iii) Keyway (iv) V-grooves (v) Rounding of corner (vi) Cutting of narrow slot and groove
Last Answer : (i) Gear Tooth : Form milling cutter, Cylindrical type or End mill type, Gear cutter. (ii) Parting off: Slitting Cutter (iii) Keyway : Staggered teeth side milling cutter, End mill cutter, key ... milling cutter. Selection of a cutter depends upon type and size of slot or groove to be produced.
Description : Which of the following set of statements represents acceptable propositions in respect of teaching-learning relationships? Choose the correct code to indicate your Answer. (i) When students fail in a test, it is the teacher who fails. ( ... (iv), (v) and (vi) (D) (i), (ii), (v) and (vi)
Last Answer : Answer: B
Description : Which of the following factors affect teaching ? Choose the correct code to indicate your answer. (i) Teacher's internal locus of control. (ii) Learner-motivation. (iii) Teacher's biographical data. (iv) Teacher's self efficacy. (v ... ), (v), (vi) and (vii) (D) (ii), (iii), (iv), (v) and (vi)
Last Answer : Answer: A
Description : Which of the following set of statements reflects the basic characteristics of teaching ? Select the correct alternative from the codes : (i) Teaching is the same as training. (ii) There is no difference between instruction and conditioning ... (vi) (C) (ii), (iii) and (v) (D) (i), (iv) and (vi)
Description : Which set of learner characteristics may be considered helpful in designing effective teaching-learning systems? Select the correct alternative from the codes given below: (i) Prior experience of learners in respect of the subject. (ii) ... iii), (iv) and (v) (D) (iii), (iv), (v) and (vi)
Description : Which of the following statements say the same thing ? (i) I am a teacher (said by Arvind) (ii) I am a teacher (said by Binod) (iii) My son is a teacher (said by Binod's father) (iv) My brother is a teacher (said ... (ii) (B) (ii), (iii), (iv) and (v) (C) (ii) and (vi) (D) (v) and (vi)
Last Answer : (B) (ii), (iii), (iv) and (v)
Description : Which of the following strings would match the regular expression: p+[3-5]*[xyz]? I. p443y Il. p6y III. 3xyz IV. p35z V. p353535x Vl. ppp5 (1) I, III and Vl only (2) IV, V and VI only (3) II, IV and V only (4) I, IV and V only
Last Answer : Answer: 4
Description : Suggest one type of materials for water proofing for the following situations. i. Rising dampness in building ii. Leakages in dam iii. Concrete continuously in wet or damp condition iv. Leakages in lavatory ,bathroom and kitchen floor v. Cracks on plastered surface vi. Cracks on roof surface
Last Answer : i. Flexible materials like butyl rubber, hot bitumen (asphalt), plastic sheets, bituminous felts, sheets of lead. ii. Liquid applied cementitious membranes iii. Liquid applied cementitious membranes ... v. Liquid applied cementitious membranes. vi. Brick bat coba, liquid applied bituminous membrane.
Description : Define following terms (i) Kinematic link (ii) Kinematic pair (iii) Kinematic chain (iv) Mechanism (v) Machine (vi) Inversion
Last Answer : (i) Kinematic link: Each part of a machine, which moves relative to some other part, is known as a kinematic link. (ii) Kinematic pair: The two links or elements of a machine, ... obtaining different mechanisms by fixing different links in a kinematic chain is known as inversion of the mechanism.
Description : Compare pin type and suspension insulators on given points: (i) Position of insulator on cross arm. (ii) Position of conductor on insulator. (iii) Reaction on cross arm. (iv) Possibility of ... Replacement cost (vi) Maximum voltage level (vii) Effect on height of supporting structure. (viii) Life
Last Answer : S.No Points Pin Type insulator Suspension or Disc Type insulator 1 Position of insulator on cross arm It is fixed on top of cross arm by using galvanized steel pin. So it is ... so to maintain minimum ground clearance height of pole increase. 8 Life Less More
Description : Perform following number system conversion : (i) (589)10 = ( )2 (ii) (101101)2 = ( )16 (iii) (413)8 = ( )2 (iv) (5AF)16 = ( )10 (v) (AC8)16 = ( )2 (vi) (106)8 = ( )10
Last Answer : (i) (589)10 = (1001001101)2 (ii) (101101)2 = ( 2D )16 (iii) (413)8 = (100001011 )2 (iv) (5AF)16 = (1455 )10 (v) (AC8)16 = (101011001000)2 (vi) (106)8 = (70)10
Description : Name the instruments used for measuring each of the following: (i) Pressure (ii) Voltage (iii) Purity of milk (iv) Temperature (v) Velocity of wind
Last Answer : Answers: (i). Barometer (ii). Voltmeter (iii). Lactometer (iv). Thermometer (v). Anemometer
Description : General exceptions are contained in (a) Chapter III of IPC (b) Chapter IV of IPC (c) Chapter V of IPC (d) Chapter VI of IPC
Last Answer : (b) Chapter IV of IPC
Description : Answer the following S. No Statement Chose the correct answer OR Fill-in-the-blanks 1 Fyrite measures CO2, O2 and SO2 True/False 2 Ultrasonic Flow Meter uses the principle of____& ____ Fill in the ... of RPM meter is used and for a visible shaft-end _______ type of RPM meter is used.
Last Answer : Sr No Statement Chose the correct answer OR Fill-in-the-blanks Solution 1 Fyrite measures CO2, O2 and SO2 True/False False 2 Ultrasonic Flow Meter uses the principle of____& ____ ... ] 10 In a gasification system the reduction zone is above the combustion zone True/False False
Description : The conversion of the throttle command voltage to the signal necessary to achieve the desired shaft RPM is accomplished by the _____________. A. ahead or astern function generator of the ... circuit C. operational amplifiers in the autorotation circuit D. long time constant amplifier circuit
Description : Which one of the following sets of parameters should be monitored for determining safe operation of journal bearing? [IES-2000] Oil pressure, bearing metal temperature and bearing vibration (b) ... shaft (c) Bearing metal temperature and oil pressure (d) Oil pressure and bearing vibration
Last Answer : Oil pressure, bearing metal temperature and bearing vibration
Description : When heavy rotating masses are connected by a shaft and equal and opposite torques are applied to these masses (rotors) A. The rotors vibrate torsionally in the same direction. B. The rotors vibrate torsionally ... on the axis of shaft which remains undisturbed by vibration. D. Both (B) and (C)
Last Answer : D. Both (B) and (C)
Description : Prepare preventive maintenance schedule for SWT related to i) Oiling and greasing ii) Electronic equipment iii) Towers
Last Answer : Preventive maintenance schedule for SWT: I. Oiling and greasing: 1) Checking geared motor oil, greasing, lubrication and maintenance of drive train. 2) Changing oil, belts, bearing lubrication. 3 ... tower. 3) Every 6 months inspection for loop condition, safety norms, tower surface.
Description : Rotor shaft of a large electric motor supported between short bearings at both ends shows a deflection of 1.8 mm in middle of motor. Assuming rotor to be perfectly balanced and supported at knife edges at both ends, likely critical speed (rpm) of shaft isA 350 B 4430 C 705 D 2810
Last Answer : C 705