Mention any two audio frequency oscillators .

Mention any two audio frequency oscillators .
by

1 Answer

Answer :

i. RC phase shift oscillator

ii. Wein bridge oscillator
by

Related questions

What are LC oscillators?

Description : What are LC oscillators?

Last Answer : Inductive oscillators also known as LC oscillators are built of an tank circuit, which oscillates by charging and discharging a capacitor through an inductor. These oscillators are typically used when a tunable precision frequency source is necessary, such as with radio transmitters and receivers

What are the classifications of Oscillators?

Description : What are the classifications of Oscillators?

Last Answer : *Based on wave generated: i. Sinusoidal Oscillator, ii. Non-sinusoidal Oscillator or Relaxation Oscillator Ex: Square wave, Triangular wave, Rectangular wave etc. *According to principle involved ... . Tuned collector base Oscillator iv. Hartley Oscillator v. Colpits Oscillator vi. Clap Oscillator

The two most common audio oscillators are

Description : The two most common audio oscillators are

Last Answer : Wein Bridge and Phase Shift

What is the difference between phase and frequency modulation? A. Is purely theoretical because they are the same in practice B. Lies in poorer audio response of phase modulation C. Lies in the different definitions of the modulation index D. Is too great to make two systems compatible

Description : What is the difference between phase and frequency modulation? A. Is purely theoretical because they are the same in practice B. Lies in poorer audio response of phase modulation C. Lies in the different definitions of the modulation index D. Is too great to make two systems compatible

Last Answer : C. Lies in the different definitions of the modulation index

What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Description : What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Last Answer : B. The ratio between the deviation of a frequency modulated signal and the modulating frequency.

What is meant by the term deviation ratio? A. The ratio of the audio modulating frequency to the center carrier frequency. B. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency. C. The ratio of the carrier center frequency to the audio modulating frequency. D. The ratio of the highest audio modulating frequency to the average audio modulating frequency.

Description : What is meant by the term deviation ratio? A. The ratio of the audio modulating frequency to the center carrier frequency. B. The ratio of the maximum carrier frequency deviation to the highest ... . D. The ratio of the highest audio modulating frequency to the average audio modulating frequency.

Last Answer : B. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

What is meant by the term deviation ratio? A. The ratio of the carrier center frequency to the audio modulating frequency B. The ratio of the highest audio modulating frequency to the average audio modulating frequency C. The ratio of the maximum carrier frequency deviation to the highest audio modulation frequency D. The ratio of the audio modulating frequency to the center carrier frequency

Description : What is meant by the term deviation ratio? A. The ratio of the carrier center frequency to the audio modulating frequency B. The ratio of the highest audio modulating frequency to the ... audio modulation frequency D. The ratio of the audio modulating frequency to the center carrier frequency

Last Answer : C. The ratio of the maximum carrier frequency deviation to the highest audio modulation frequency

An instrument for recording waveforms of audio frequency. A. Oscilloscope B. Phonoscope C. Radioscope D. Audioscope

Description : An instrument for recording waveforms of audio frequency. A. Oscilloscope B. Phonoscope C. Radioscope D. Audioscope

Last Answer : B. Phonoscope

______ used to measure speech volume A. Volume meter B. Audio frequency meter C. Volume unit meter D. Speech meter

Description : ______ used to measure speech volume A. Volume meter B. Audio frequency meter C. Volume unit meter D. Speech meter

Last Answer : C. Volume unit meter

The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the same bandwidth. A. Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Description : The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the ... . Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Last Answer : D. Residual noise level

ECE Board Exam March 1996 According to the Nyquist theorem, the sampling rate that can be used in a PCM system is ________ the highest audio frequency. A. once B. eight times C. twice D. thrice

Description : ECE Board Exam March 1996 According to the Nyquist theorem, the sampling rate that can be used in a PCM system is ________ the highest audio frequency. A. once B. eight times C. twice D. thrice

Last Answer : C. twice

What is the frequency range of magnetron oscillators?

Description : What is the frequency range of magnetron oscillators?

Last Answer : 600-30,000 megahertz.

What is the frequency range of magnetron oscillators?

Description : What is the frequency range of magnetron oscillators?

Last Answer : . 600-30,000 megahertz.

Which of the following oscillators is used for generation of high frequency signal ?

Description : Which of the following oscillators is used for generation of high frequency signal ? (a) RC phase shift oscillator (b) Blocking oscillator (c) Wein bridge oscillator (d) L-C oscillator 

Last Answer : LC oscillator is used for generation of high frequency signal. 

A test method of comparing two audio systems by switching inputs so that the same recording is heard in rapid succession over one given system and then the other. A. B test B. A test C. AB test D. C test

Description : A test method of comparing two audio systems by switching inputs so that the same recording is heard in rapid succession over one given system and then the other. A. B test B. A test C. AB test D. C test

Last Answer : C. AB test

Which standard is utilized in intermodulation noise rates on PCM audio channels? A. CCIT Rec. G.151 B. CCIT Rec. G.172 C. CCIT Rec. G.190 D. CCIT Rec. G.190

Description : Which standard is utilized in intermodulation noise rates on PCM audio channels? A. CCIT Rec. G.151 B. CCIT Rec. G.172 C. CCIT Rec. G.190 D. CCIT Rec. G.190

Last Answer : B. CCIT Rec. G.172

A form of regenerative repeater for transmitting signals over a long cable received through a relay in a clearer form. A. Active generator B. Active repeater C. Interpolator D. Audio generator

Description : A form of regenerative repeater for transmitting signals over a long cable received through a relay in a clearer form. A. Active generator B. Active repeater C. Interpolator D. Audio generator

Last Answer : C. Interpolator

Where is the brightness control located in a TV? A. The audio section B. The video section C. The grid-cathode circuit D. The front panel

Description : Where is the brightness control located in a TV? A. The audio section B. The video section C. The grid-cathode circuit D. The front panel

Last Answer : A. The audio section

What is the standard test tone used for audio measurements? A. 100 Hz B. 500 Hz C. 1000 Hz D. 2000 Hz

Description : What is the standard test tone used for audio measurements? A. 100 Hz B. 500 Hz C. 1000 Hz D. 2000 Hz

Last Answer : C. 1000 Hz

A 1 Mhz carrier is amplitude modulated by a pure 200-Hz audio test tone. Which of the following combinations of frequencies represent the total content of the AM signal? A. 1 MHz and 200 Hz B. 1 MHz and 1000.2 kHz C. 999.8 kHz, 1000 kHz, and 1000.2 kHz D. 999.8 kHz and 1000.2 kHz

Description : A 1 Mhz carrier is amplitude modulated by a pure 200-Hz audio test tone. Which of the following combinations of frequencies represent the total content of the AM signal? A. 1 MHz and 200 Hz B. 1 MHz and 1000.2 kHz C. 999.8 kHz, 1000 kHz, and 1000.2 kHz D. 999.8 kHz and 1000.2 kHz

Last Answer : C. 999.8 kHz, 1000 kHz, and 1000.2 kHz

________ is the method of encoding audio signals used in US standard 1544 kbit/s 24 channel PCM systems. A. Shannon’s law B. A-law C. Newton’s law D. Mu-law

Description : ________ is the method of encoding audio signals used in US standard 1544 kbit/s 24 channel PCM systems. A. Shannon’s law B. A-law C. Newton’s law D. Mu-law

Last Answer : D. Mu-law

How can receiver desensitizing be reduced? A. Increase the receiver bandwidth B. Ensure good RF shielding between the transmitter and receiver C. Increase the transmitter audio gain D. Decrease the receiver squelch, gain.

Description : How can receiver desensitizing be reduced? A. Increase the receiver bandwidth B. Ensure good RF shielding between the transmitter and receiver C. Increase the transmitter audio gain D. Decrease the receiver squelch, gain.

Last Answer : D. Decrease the receiver squelch, gain.

What is the effect in over modulated amplitude modulated radio broadcasting transmission? A. Interference to adjacent channel B. Higher fidelity C. Increase noise D. Higher audio signal

Description : What is the effect in over modulated amplitude modulated radio broadcasting transmission? A. Interference to adjacent channel B. Higher fidelity C. Increase noise D. Higher audio signal

Last Answer : A. Interference to adjacent channel

Atmospheric noise is less at severe frequencies above A. Audio level B. 30 MHz C. 10 GHz D. 1 GHz

Description : Atmospheric noise is less at severe frequencies above A. Audio level B. 30 MHz C. 10 GHz D. 1 GHz

Last Answer : B. 30 MHz

Which of the following is not a baseband signal modulation? A. RF carrier B. Video System C. Audio signal D. Binary coded pulses

Description : Which of the following is not a baseband signal modulation? A. RF carrier B. Video System C. Audio signal D. Binary coded pulses

Last Answer : A. RF carrier

Three audio waves with 100,200 and 300 volts amplitude respectively, simultaneously modulate a 450 volts carrier. What is the total percent of modulation of the AM wave? A. 69 % B. 115.5 % C. 50% D. 83%

Description : Three audio waves with 100,200 and 300 volts amplitude respectively, simultaneously modulate a 450 volts carrier. What is the total percent of modulation of the AM wave? A. 69 % B. 115.5 % C. 50% D. 83%

Last Answer : D. 83%

What is audio amplifier?

Description : What is audio amplifier?

Last Answer : The amplifier receives an input from signal source or from a transducer and gives out an amplified signal to the output device is called an audio amplifier. 

What are the two most popular RF oscillators?

Description : What are the two most popular RF oscillators?

Last Answer : Colpitts and Hartley

Where can I buy bulk crystal oscillators?

Description : Where can I buy bulk crystal oscillators?

Last Answer : Vectron

Since the characteristics of the device shown in figure 'A' of the illustration includes a stable voltage and low current while operating, it can be suitably used in _____________. EL-0065 A. oscillators and SCR trigger circuits B. class A and B amplifiers C. generator rectifier and filtering supplies D. all of the above

Description : Since the characteristics of the device shown in figure 'A' of the illustration includes a stable voltage and low current while operating, it can be suitably used in _____________. EL-0065 A. oscillators ... . class A and B amplifiers C. generator rectifier and filtering supplies D. all of the above

Last Answer : Answer: A

Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback

Description : Which of the following is not true: A) An oscillator is a circuit that converts DC to AC B) An oscillator is an amplifier that supplies its own input signal C) All oscillators generate sine waves D) In phase feedback is called positive Feedback

Last Answer : C) All oscillators generate sine waves

Oscillators that are turned on and off at a specific time are known as what type of oscillators?

Description : Oscillators that are turned on and off at a specific time are known as what type of oscillators?

Last Answer : Pulsed oscillators.

What is another name for nonsinusoidal oscillators?

Description : What is another name for nonsinusoidal oscillators?

Last Answer : Relaxation oscillators.

What are the three basic configurations of transistor oscillators?

Description : What are the three basic configurations of transistor oscillators?

Last Answer : Common collector (CC), common emitter (CE), and common base (CB).

To develop the correct mathematical description of the distribution of radiated energy of a blackbody with respect to wavelength for a given temperature, Planck found it necessary to assume that the molecular oscillators of the blackbody emitted and absorbed: w) no radiant energy x) radiant energy in discrete units or quanta y) radiant energy in a continuous form z) none of the above.

Description : To develop the correct mathematical description of the distribution of radiated energy of a blackbody with respect to wavelength for a given temperature, Planck found it necessary to assume that the molecular ... units or quanta y) radiant energy in a continuous form z) none of the above.

Last Answer : ANSWER: X -- RADIANT ENERGY IN DISCRETE UNITS OR QUANTA

Oscillators have______

Last Answer : Oscillators have Positive feedback.

Define Multivibrators. Mention its types.

Description : Define Multivibrators. Mention its types.

Last Answer : Multivibrators are regenerative circuits, Which are mainly used in timing applications. Based on their operational characteristics they can be classified into • Astable Multivibrators • Monostable Multivibrators • Bistable Multivibrators

Mention the advantages of opto-couplers:

Description : Mention the advantages of opto-couplers:

Last Answer : *Better isolation between the two stages. *Impedance problem between the stages is eliminated. *Wide frequency response. *Easily interfaced with digital circuit. *Compact and light weight. *Problems such as noise, transients, contact bounce,.. are eliminated. 

Mention some applications of 555 timer

Description : Mention some applications of 555 timer

Last Answer : *Oscillator *pulse generator *ramp and square wave generator *mono-shot multivibrator *burglar alarm *traffic light control.

Mention some typical applications of PLL

Description : Mention some typical applications of PLL

Last Answer : • Frequency multiplication/division • Frequency translation • AM detection • FM demodulation • FSK demodulation.

Mention some areas where PLL is widely used.

Description : Mention some areas where PLL is widely used.

Last Answer : 1.Radar synchronizations 2. Satellite communication systems 3. Air borne navigational systems 4. FM communication systems 5.Computers.

Mention some of the non – linear applications of op-amps

Description : Mention some of the non – linear applications of op-amps

Last Answer : Rectifier, peak detector, clipper, clamper, sample and hold circuit, log amplifier, anti –log amplifier, multiplier are some of the non – linear op-amp circuits. 

Mention some of the linear applications of op – amps.

Description : Mention some of the linear applications of op – amps.

Last Answer : Adder, subtractor, voltage –to- current converter, current –to- voltage converters, instrumentation amplifier, analog computation ,power amplifier, etc are some of the linear opamp circuits.

Mention the advantages of Wilson current source.

Description : Mention the advantages of Wilson current source.

Last Answer : (i) Provides high output resistance. (ii) Offers low sensitivity to transistor base currents.

Mention the advantages of integrated circuits over discrete components.

Description : Mention the advantages of integrated circuits over discrete components.

Last Answer : *Miniaturisation and hence increased equipment density. *Cost reduction due to batch processing. *Increased system reliability due to the elimination of soldered joints. *Improved functional performance. *Matched devices. *Increased operating speeds. *Reduction in power consumption.

What is antenna bandwidth? A. Antenna length divided by the number of elements B. The angle between the half-power radiation points C. The angle formed between two imaginary lines drawn through D. The frequency range over which an antenna can be expected to operate satisfactorily

Description : What is antenna bandwidth? A. Antenna length divided by the number of elements B. The angle between the half-power radiation points C. The angle formed between two imaginary lines drawn through D. The frequency range over which an antenna can be expected to operate satisfactorily

Last Answer : D. The frequency range over which an antenna can be expected to operate satisfactorily

A Hertz antenna is operating on a frequency of 2182 kHz and consists of a horizontal wire that is hanged between two towers. What is the frequency of its third harmonic? A. 727 kHz B. 6546 kHz C. 436 kHz D. 6.546 kHz

Description : A Hertz antenna is operating on a frequency of 2182 kHz and consists of a horizontal wire that is hanged between two towers. What is the frequency of its third harmonic? A. 727 kHz B. 6546 kHz C. 436 kHz D. 6.546 kHz

Last Answer : B. 6546 kHz

The total space loss of transmission and reception for two ground stations with uplink frequency 8GHz and a downlink of 6 GHz with angle of elevations of 3˚ and 7˚ A respectively is A. 403 dB B. 100 dB C. 20 dB D. 215 dB

Description : The total space loss of transmission and reception for two ground stations with uplink frequency 8GHz and a downlink of 6 GHz with angle of elevations of 3˚ and 7˚ A respectively is A. 403 dB B. 100 dB C. 20 dB D. 215 dB

Last Answer : A. 403 dB