What is meant by the term deviation ratio? A. The ratio of the audio modulating frequency to the center carrier frequency. B. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency. C. The ratio of the carrier center frequency to the audio modulating frequency. D. The ratio of the highest audio modulating frequency to the average audio modulating frequency.

What is meant by the term deviation ratio?
A. The ratio of the audio modulating frequency to the center carrier frequency.
B. The ratio of the maximum carrier frequency deviation to the highest audio
modulating frequency.
C. The ratio of the carrier center frequency to the audio modulating frequency.
D. The ratio of the highest audio modulating frequency to the average audio modulating
frequency.
by

1 Answer

Answer :

B. The ratio of the maximum carrier frequency deviation to the highest audio
modulating frequency.
by

Related questions

What is meant by the term deviation ratio? A. The ratio of the carrier center frequency to the audio modulating frequency B. The ratio of the highest audio modulating frequency to the average audio modulating frequency C. The ratio of the maximum carrier frequency deviation to the highest audio modulation frequency D. The ratio of the audio modulating frequency to the center carrier frequency

Description : What is meant by the term deviation ratio? A. The ratio of the carrier center frequency to the audio modulating frequency B. The ratio of the highest audio modulating frequency to the ... audio modulation frequency D. The ratio of the audio modulating frequency to the center carrier frequency

Last Answer : C. The ratio of the maximum carrier frequency deviation to the highest audio modulation frequency

What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Description : What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Last Answer : B. The ratio between the deviation of a frequency modulated signal and the modulating frequency.

What is the approximate bandwidth of an FM system with 10 kHz of modulating frequency and a 150 kHz of frequency deviation? A. 300 kHz B. 320 kHz C. 150 kHz D. 200 kHz

Description : What is the approximate bandwidth of an FM system with 10 kHz of modulating frequency and a 150 kHz of frequency deviation? A. 300 kHz B. 320 kHz C. 150 kHz D. 200 kHz

Last Answer : B. 320 kHz

In a FM system, the maximum deviation is 75KHz. Find bandwidth for modulating frequency i. fm=500Hz ii. fm=5KHz iii. fm=10KHz Draw conclusion for bandwidth of FM from answer.

Description : In a FM system, the maximum deviation is 75KHz. Find bandwidth for modulating frequency i. fm=500Hz ii. fm=5KHz iii. fm=10KHz Draw conclusion for bandwidth of FM from answer.

Last Answer : Given deviation∆=75kHz i) fm=500Hz bandwidth B.W=2(∆+fm)  =2(75k+500)=151kHz  ii). fm=5KHz bandwidth B.W=2(∆+fm)  =2(75k+5k)=160KHz iii) fm=10KHz bandwidth B.W=2(∆+fm)  =2(75k+10k)=170KHz As the modulating frequency increases bandwidth also increases.

Compare narrow band FM with wide-band FM w.r.t. following points. (i) Modulation index (ii) Maximum deviation (iii)Range of modulating frequency (iv)Application

Description : Compare narrow band FM with wide-band FM w.r.t. following points. (i) Modulation index (ii) Maximum deviation (iii)Range of modulating frequency (iv)Application

Last Answer : Sr. No Parameters Narrow band FM Wide band FM 1 Modulation index Less than or slightly greater than 1 Greater than 1  2 Maximum deviation ... like police wireless, ambulance etc. Entertainment broadcasting can be used for high quality music transmission 

In radio signal emission designation, the fifth symbol means A. Details of signals B. Type of information transmitted C. Nature of multiplexing D. Nature of signal modulating the main carrier

Description : In radio signal emission designation, the fifth symbol means A. Details of signals B. Type of information transmitted C. Nature of multiplexing D. Nature of signal modulating the main carrier

Last Answer : C. Nature of multiplexing

The third symbol in the designation of radio emission under the ITU rules refers to A. Type of the modulation of the main carrier B. Bandwidth C. Nature of the signals modulating the main carrier D. Type of information to be transmitted

Description : The third symbol in the designation of radio emission under the ITU rules refers to A. Type of the modulation of the main carrier B. Bandwidth C. Nature of the signals modulating the main carrier D. Type of information to be transmitted

Last Answer : D. Type of information to be transmitted

The first symbol in the designation of radio emission under the ITU rules to A. Nature of signals modulating the main carrier B. Type of information to be transmitted C. Bandwidth D. Type of modulation of the main carrier

Description : The first symbol in the designation of radio emission under the ITU rules to A. Nature of signals modulating the main carrier B. Type of information to be transmitted C. Bandwidth D. Type of modulation of the main carrier

Last Answer : D. Type of modulation of the main carrier

If the percentage modulation of an AM amplifier is 88% and the modulating signal is 1 volt, the carrier has an amplitude of _______________. A. 1.14 volts B. 0.88 volt C. 1.88 volts D. 0.12 volt

Description : If the percentage modulation of an AM amplifier is 88% and the modulating signal is 1 volt, the carrier has an amplitude of _______________. A. 1.14 volts B. 0.88 volt C. 1.88 volts D. 0.12 volt

Last Answer : A. 1.14 volts

What is the term used to describe a spread spectrum communications system where the center frequency if a conventional carrier is altered many time per second in accordance with a pseudo-random list of channels? A. Frequency hopping B. Direct sequence C. Time-domain frequency modulation D. Frequency compandored spread spectrum

Description : What is the term used to describe a spread spectrum communications system where the center frequency if a conventional carrier is altered many time per second in accordance with a pseudo ... hopping B. Direct sequence C. Time-domain frequency modulation D. Frequency compandored spread spectrum

Last Answer : A. Frequency hopping

What is the deviation ratio for an FM-phone signal having a maximum frequency swing of plus or minus 5 kHz and accepting a maximum modulation rate of 3kHz? A. 60 B. 0.16 C. 0.6 D. 1.66

Description : What is the deviation ratio for an FM-phone signal having a maximum frequency swing of plus or minus 5 kHz and accepting a maximum modulation rate of 3kHz? A. 60 B. 0.16 C. 0.6 D. 1.66

Last Answer : D. 1.66

The modulation index of a FM Signal having modulating frequency 2 KHz and Max deviation is 10 KHz, is: -

Description : The modulation index of a FM Signal having modulating frequency 2 KHz and Max deviation is 10 KHz, is: -  a) 2 b) 5 c) 3 d) 4

Last Answer : The modulation index of a FM Signal having modulating frequency 2 KHz and Max deviation is 10 KHz, is: - 5

Deemphasis in the receiver in effect attenuates modulating signal components and noise in what frequency range? A. dc B. low C. intermediate D. high

Description : Deemphasis in the receiver in effect attenuates modulating signal components and noise in what frequency range? A. dc B. low C. intermediate D. high

Last Answer : D. high

Refer to the deviation of the operating frequency of a crystal oscillator from its nominal value due to temperature variations. A. Drift B. Flash over C. Frequency deviation D. Deviation ratio

Description : Refer to the deviation of the operating frequency of a crystal oscillator from its nominal value due to temperature variations. A. Drift B. Flash over C. Frequency deviation D. Deviation ratio

Last Answer : A. Drift

In_____ transmission, the frequency of the carrier signal is modulated to follow the changing voltage level (amplitude)of the modulating signal. The peak amplitude and phase of the carrier signal remainconstant,but as the amplitudeof the information signal changes, thefrequency of thecarrier changes correspondingly. A) AM B) PM C) FM D) none of the above

Description : In_____ transmission, the frequency of the carrier signal is modulated to follow the changing voltage level (amplitude)of the modulating signal. The peak amplitude and phase of the carrier signal remainconstant,but as ... of thecarrier changes correspondingly. A) AM B) PM C) FM D) none of the above

Last Answer : FM

ECE Board Exam March 1996 According to the Nyquist theorem, the sampling rate that can be used in a PCM system is ________ the highest audio frequency. A. once B. eight times C. twice D. thrice

Description : ECE Board Exam March 1996 According to the Nyquist theorem, the sampling rate that can be used in a PCM system is ________ the highest audio frequency. A. once B. eight times C. twice D. thrice

Last Answer : C. twice

It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation, taken under the normal operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Description : It is an average power of a radio transmitter supplied to the antenna transmission line taken during a long sufficient interval of time and compared with the lowest frequency encountered in the modulation ... operating conditions. A. Carrier power B. Rated power C. Mean power D. Peak envelop power

Last Answer : C. Mean power

Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Description : Referred to as an average power from the radio transmitter supplied to the antenna transmission line taken during one radio frequency cycle under no modulation. A. Carrier power B. Rated power C. Peak envelop power D. Mean power

Last Answer : A. Carrier power

Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Description : Average power of a radio transmitter supplied to the antenna transmission line by a transmitter during one radio frequency cycle taken under the condition of no modulation. A. Peak envelop power B. Rated power C. Carrier power D. Mean power

Last Answer : C. Carrier power

A 1 Mhz carrier is amplitude modulated by a pure 200-Hz audio test tone. Which of the following combinations of frequencies represent the total content of the AM signal? A. 1 MHz and 200 Hz B. 1 MHz and 1000.2 kHz C. 999.8 kHz, 1000 kHz, and 1000.2 kHz D. 999.8 kHz and 1000.2 kHz

Description : A 1 Mhz carrier is amplitude modulated by a pure 200-Hz audio test tone. Which of the following combinations of frequencies represent the total content of the AM signal? A. 1 MHz and 200 Hz B. 1 MHz and 1000.2 kHz C. 999.8 kHz, 1000 kHz, and 1000.2 kHz D. 999.8 kHz and 1000.2 kHz

Last Answer : C. 999.8 kHz, 1000 kHz, and 1000.2 kHz

Which of the following is not a baseband signal modulation? A. RF carrier B. Video System C. Audio signal D. Binary coded pulses

Description : Which of the following is not a baseband signal modulation? A. RF carrier B. Video System C. Audio signal D. Binary coded pulses

Last Answer : A. RF carrier

Three audio waves with 100,200 and 300 volts amplitude respectively, simultaneously modulate a 450 volts carrier. What is the total percent of modulation of the AM wave? A. 69 % B. 115.5 % C. 50% D. 83%

Description : Three audio waves with 100,200 and 300 volts amplitude respectively, simultaneously modulate a 450 volts carrier. What is the total percent of modulation of the AM wave? A. 69 % B. 115.5 % C. 50% D. 83%

Last Answer : D. 83%

What term is used to describe a spread spectrum communications system in which a very fast binary bit stream is used to shift the phase of an RF carrier? A. Frequency hopping B. Direct sequence C. Binary phase-shift keying D. Phase compandored spread spectrum

Description : What term is used to describe a spread spectrum communications system in which a very fast binary bit stream is used to shift the phase of an RF carrier? A. Frequency hopping B. Direct sequence C. Binary phase-shift keying D. Phase compandored spread spectrum

Last Answer : B. Direct sequence

The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the same bandwidth. A. Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Description : The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the ... . Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Last Answer : D. Residual noise level

One of the FM signal generator control which varies the phase of the modulating voltage applied to the oscillator of the sweep generator A. Band control B. Phase control C. Marker amplitude control D. Sweep output control

Description : One of the FM signal generator control which varies the phase of the modulating voltage applied to the oscillator of the sweep generator A. Band control B. Phase control C. Marker amplitude control D. Sweep output control

Last Answer : B. Phase control

The allowable deviation ratio of commercial FM broadcast. A. 25 B. 15 C. 5 D. 75

Description : The allowable deviation ratio of commercial FM broadcast. A. 25 B. 15 C. 5 D. 75

Last Answer : C. 5

In_____ transmission, thephaseof the carrier signal is modulated to follow the changingvoltage level (amplitude) of the modulating signal. A) AM B) PM C) FM D) none of the above

Description : In_____ transmission, thephaseof the carrier signal is modulated to follow the changingvoltage level (amplitude) of the modulating signal. A) AM B) PM C) FM D) none of the above

Last Answer : PM

Cellular radios use FM with a maximum deviation of A. ±30 khz B. ±75 khz C. ±25 khz D. ±12 khz

Description : Cellular radios use FM with a maximum deviation of A. ±30 khz B. ±75 khz C. ±25 khz D. ±12 khz

Last Answer : D. ±12 khz

What is meant by the term antenna bandwidth A. Antenna length divided by the number of elements. B. The angle between the half-power radiation points C. The frequency range over which and antenna can be expected to perform well D. The angle formed between two imaginary line drawn through the ends of the elements

Description : What is meant by the term antenna bandwidth A. Antenna length divided by the number of elements. B. The angle between the half-power radiation points C. The frequency range over which and antenna ... perform well D. The angle formed between two imaginary line drawn through the ends of the elements

Last Answer : C. The frequency range over which and antenna can be expected to perform well

How far is the visual carrier from the lowest frequency in the spectrum of a monochrome TV broadcast channel following the NTSC standard? A. 1.5 MHz B. 1.25 MHz C. 4.5 MHz D. 0.25 MHz

Description : How far is the visual carrier from the lowest frequency in the spectrum of a monochrome TV broadcast channel following the NTSC standard? A. 1.5 MHz B. 1.25 MHz C. 4.5 MHz D. 0.25 MHz

Last Answer : B. 1.25 MHz

What is the channel number of an FM station with a carrier frequency of 99.5 MHz? A. 256 B. 258 C. 257 D. 259

Description : What is the channel number of an FM station with a carrier frequency of 99.5 MHz? A. 256 B. 258 C. 257 D. 259

Last Answer : B. 258

____ system transmits frequency-division-multiplexed voice band signals over a coaxial cable for distances up to 4000 miles. A. T carrier B. X carrier C. L carrier D. F carrier

Description : ____ system transmits frequency-division-multiplexed voice band signals over a coaxial cable for distances up to 4000 miles. A. T carrier B. X carrier C. L carrier D. F carrier

Last Answer : C. L carrier

What is the carrier frequency of supergroup 10? A. 2724 kHz B. 2356 kHz C. 2108 kHz D. 3100 kHz

Description : What is the carrier frequency of supergroup 10? A. 2724 kHz B. 2356 kHz C. 2108 kHz D. 3100 kHz

Last Answer : D. 3100 kHz

This is referred to a product of simultaneous frequency and amplitude modulation or a carrier frequency variation which produces unwanted distortion. A. Absorption modulation B. Simultaneous modulation C. Dynamic instability D. Series modulation

Description : This is referred to a product of simultaneous frequency and amplitude modulation or a carrier frequency variation which produces unwanted distortion. A. Absorption modulation B. Simultaneous modulation C. Dynamic instability D. Series modulation

Last Answer : C. Dynamic instability

A carrier signal has ______. A. Constant peak amplitude B. The information C. Frequency range 20-20000 Hz D. A varying amplitude

Description : A carrier signal has ______. A. Constant peak amplitude B. The information C. Frequency range 20-20000 Hz D. A varying amplitude

Last Answer : A. Constant peak amplitude

Which determines the number of sideband components of FM? A. Modulation frequency B. Modulation index C. Carrier frequency D. All of these

Description : Which determines the number of sideband components of FM? A. Modulation frequency B. Modulation index C. Carrier frequency D. All of these

Last Answer : B. Modulation index

What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Description : What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice ... a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Last Answer : C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz

An instrument for recording waveforms of audio frequency. A. Oscilloscope B. Phonoscope C. Radioscope D. Audioscope

Description : An instrument for recording waveforms of audio frequency. A. Oscilloscope B. Phonoscope C. Radioscope D. Audioscope

Last Answer : B. Phonoscope

______ used to measure speech volume A. Volume meter B. Audio frequency meter C. Volume unit meter D. Speech meter

Description : ______ used to measure speech volume A. Volume meter B. Audio frequency meter C. Volume unit meter D. Speech meter

Last Answer : C. Volume unit meter

What is the difference between phase and frequency modulation? A. Is purely theoretical because they are the same in practice B. Lies in poorer audio response of phase modulation C. Lies in the different definitions of the modulation index D. Is too great to make two systems compatible

Description : What is the difference between phase and frequency modulation? A. Is purely theoretical because they are the same in practice B. Lies in poorer audio response of phase modulation C. Lies in the different definitions of the modulation index D. Is too great to make two systems compatible

Last Answer : C. Lies in the different definitions of the modulation index

Mention any two audio frequency oscillators .

Description : Mention any two audio frequency oscillators .

Last Answer : i. RC phase shift oscillator ii. Wein bridge oscillator

What is meant by frequency deviation?

Description : What is meant by frequency deviation?

Last Answer : The difference between the carrier frequency of an fm signal and its maximum frequency excursion when modulated.

Highest frequency that can be used for skywave HF communications between two given points on earth. A. Gyro frequency B. Maximum usable frequency C. Critical frequency D. Virtual frequency

Description : Highest frequency that can be used for skywave HF communications between two given points on earth. A. Gyro frequency B. Maximum usable frequency C. Critical frequency D. Virtual frequency

Last Answer : B. Maximum usable frequency

What satellite system parameter represents the quality of a satellite or an earth station receiver? A. Gain-to-Equivalent Noise Temperature Ratio (G/Te) B. Energy of Bit-to-Noise Density Ratio (Eb/No) C. Carrier-to-Noise Density Ratio (C/No) D. Bit energy

Description : What satellite system parameter represents the quality of a satellite or an earth station receiver? A. Gain-to-Equivalent Noise Temperature Ratio (G/Te) B. Energy of Bit-to-Noise Density Ratio (Eb/No) C. Carrier-to-Noise Density Ratio (C/No) D. Bit energy

Last Answer : A. Gain-to-Equivalent Noise Temperature Ratio (G/Te)

A coherent binary phase shift keyed BPSK transmitter operates at a bit rate of 20 Mbps with a carrier to noise ratio C/N of 8.8dB. Find Eb/No. A. 73 dB B. 62.4 dB C. 81.8 dB D. 8.8 dB

Description : A coherent binary phase shift keyed BPSK transmitter operates at a bit rate of 20 Mbps with a carrier to noise ratio C/N of 8.8dB. Find Eb/No. A. 73 dB B. 62.4 dB C. 81.8 dB D. 8.8 dB

Last Answer : D. 8.8 dB

What aircraft deviation is measured by an ILS localizer? A. Altitude B. Ground speed C. Vertical D. Horizontal

Description : What aircraft deviation is measured by an ILS localizer? A. Altitude B. Ground speed C. Vertical D. Horizontal

Last Answer : D. Horizontal

The standard deviation of the variation in the transmission loss of a circuit should not exceed A. 3 dB B. 1 dB C. 5 dB D. 0.5dB

Description : The standard deviation of the variation in the transmission loss of a circuit should not exceed A. 3 dB B. 1 dB C. 5 dB D. 0.5dB

Last Answer : B. 1 dB

What is the required quality factor for an SSB filter with the following data: center frequency= 1 MHz, the desired attenuation level of the unwanted sideband= 80 dB and the separation between sidebands= 200 Hz? A. 1,250 B. 12,500 C. 125,000 D. 25,000

Description : What is the required quality factor for an SSB filter with the following data: center frequency= 1 MHz, the desired attenuation level of the unwanted sideband= 80 dB and the separation between sidebands= 200 Hz? A. 1,250 B. 12,500 C. 125,000 D. 25,000

Last Answer : C. 125,000

What is the typical center frequency spacing between adjacent channels (transponders) in satellites? A. 36 MHz B. 40 MHz C. 500 MHz D. 4 MHz

Description : What is the typical center frequency spacing between adjacent channels (transponders) in satellites? A. 36 MHz B. 40 MHz C. 500 MHz D. 4 MHz

Last Answer : B. 40 MHz

Assume a frequency range of 405.0125 MHz to 405.0875 MHz and 25 kHz channeling plan, determine the center frequency of the second channel from the lower limit. A. 405.030 MHz B. 405.025 MHz C. 405.050 MHz D. 405.075 MHz

Description : Assume a frequency range of 405.0125 MHz to 405.0875 MHz and 25 kHz channeling plan, determine the center frequency of the second channel from the lower limit. A. 405.030 MHz B. 405.025 MHz C. 405.050 MHz D. 405.075 MHz

Last Answer : C. 405.050 MHz