______ used to measure speech volume A. Volume meter B. Audio frequency meter C. Volume unit meter D. Speech meter

______ used to measure speech volume
A. Volume meter
B. Audio frequency meter
C. Volume unit meter
D. Speech meter
by

1 Answer

Answer :

C. Volume unit meter
by

Related questions

A method of expressing the amplitude of complex non-periodic signals such as speech. A. Frequency B. Wavelength C. Volume D. Pitch

Description : A method of expressing the amplitude of complex non-periodic signals such as speech. A. Frequency B. Wavelength C. Volume D. Pitch

Last Answer : C. Volume

What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Description : What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Last Answer : B. The ratio between the deviation of a frequency modulated signal and the modulating frequency.

What is meant by the term deviation ratio? A. The ratio of the audio modulating frequency to the center carrier frequency. B. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency. C. The ratio of the carrier center frequency to the audio modulating frequency. D. The ratio of the highest audio modulating frequency to the average audio modulating frequency.

Description : What is meant by the term deviation ratio? A. The ratio of the audio modulating frequency to the center carrier frequency. B. The ratio of the maximum carrier frequency deviation to the highest ... . D. The ratio of the highest audio modulating frequency to the average audio modulating frequency.

Last Answer : B. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

What is meant by the term deviation ratio? A. The ratio of the carrier center frequency to the audio modulating frequency B. The ratio of the highest audio modulating frequency to the average audio modulating frequency C. The ratio of the maximum carrier frequency deviation to the highest audio modulation frequency D. The ratio of the audio modulating frequency to the center carrier frequency

Description : What is meant by the term deviation ratio? A. The ratio of the carrier center frequency to the audio modulating frequency B. The ratio of the highest audio modulating frequency to the ... audio modulation frequency D. The ratio of the audio modulating frequency to the center carrier frequency

Last Answer : C. The ratio of the maximum carrier frequency deviation to the highest audio modulation frequency

An instrument for recording waveforms of audio frequency. A. Oscilloscope B. Phonoscope C. Radioscope D. Audioscope

Description : An instrument for recording waveforms of audio frequency. A. Oscilloscope B. Phonoscope C. Radioscope D. Audioscope

Last Answer : B. Phonoscope

The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the same bandwidth. A. Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Description : The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the ... . Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Last Answer : D. Residual noise level

What is the difference between phase and frequency modulation? A. Is purely theoretical because they are the same in practice B. Lies in poorer audio response of phase modulation C. Lies in the different definitions of the modulation index D. Is too great to make two systems compatible

Description : What is the difference between phase and frequency modulation? A. Is purely theoretical because they are the same in practice B. Lies in poorer audio response of phase modulation C. Lies in the different definitions of the modulation index D. Is too great to make two systems compatible

Last Answer : C. Lies in the different definitions of the modulation index

ECE Board Exam March 1996 According to the Nyquist theorem, the sampling rate that can be used in a PCM system is ________ the highest audio frequency. A. once B. eight times C. twice D. thrice

Description : ECE Board Exam March 1996 According to the Nyquist theorem, the sampling rate that can be used in a PCM system is ________ the highest audio frequency. A. once B. eight times C. twice D. thrice

Last Answer : C. twice

Mention any two audio frequency oscillators .

Description : Mention any two audio frequency oscillators .

Last Answer : i. RC phase shift oscillator ii. Wein bridge oscillator

Your Western Electric 3A test set meter reading is -23 dBm at at test point level of -8 dB. This is ______ dBrnc0. A. 75 B. 29 C. 30 D. 31

Description : Your Western Electric 3A test set meter reading is -23 dBm at at test point level of -8 dB. This is ______ dBrnc0. A. 75 B. 29 C. 30 D. 31

Last Answer : A. 75

What is the optimum volume per person of rooms for speech? A. 2.8 B. 3.1 C. 4.2 D. 5.1

Description : What is the optimum volume per person of rooms for speech? A. 2.8 B. 3.1 C. 4.2 D. 5.1

Last Answer : A. 2.8

What is the unit of electric field strength? A. Watt/meter B. Ohms/meter C. Ampere/meter D. Watt/meter2 E. No answer

Description : What is the unit of electric field strength? A. Watt/meter B. Ohms/meter C. Ampere/meter D. Watt/meter2 E. No answer

Last Answer : E. No answer

What volume of the chamber is required to measure absorption coefficient at 100 Hz? A. 125 m3 B. 50 m3 C. 150 m3 D. 352 m3

Description : What volume of the chamber is required to measure absorption coefficient at 100 Hz? A. 125 m3 B. 50 m3 C. 150 m3 D. 352 m3

Last Answer : D. 352 m3

In radio High frequency communications the higher the radio frequency the ______. A. Higher it can reach B. Shorter it can reach C. Effect is null D. Longer it can reach

Description : In radio High frequency communications the higher the radio frequency the ______. A. Higher it can reach B. Shorter it can reach C. Effect is null D. Longer it can reach

Last Answer : D. Longer it can reach

The method of determining the bandwidth of any processing system is ______. A. Bandwidth analysis B. Frequency spectrum C. Spectral analysis D. Frequency analysis

Description : The method of determining the bandwidth of any processing system is ______. A. Bandwidth analysis B. Frequency spectrum C. Spectral analysis D. Frequency analysis

Last Answer : C. Spectral analysis

A carrier signal has ______. A. Constant peak amplitude B. The information C. Frequency range 20-20000 Hz D. A varying amplitude

Description : A carrier signal has ______. A. Constant peak amplitude B. The information C. Frequency range 20-20000 Hz D. A varying amplitude

Last Answer : A. Constant peak amplitude

Sound of frequency below 20 Hz is called ______. (1) audio sounds (2) infrasonic (3) ultrasonic (4) supersonics

Description : Sound of frequency below 20 Hz is called ______. (1) audio sounds (2) infrasonic (3) ultrasonic (4) supersonics

Last Answer : (2) infrasonic Explanation: The term "infrasonic" applied to sound refers to sound waves below the frequencies of audible sound and nominally includes anything under 20 Hz.

What is affected by the distance between the listener and the source of the sound because the intensity varies inversely with the square of the distance? A. Volume B. Pitch C. Loudness D. Frequency

Description : What is affected by the distance between the listener and the source of the sound because the intensity varies inversely with the square of the distance? A. Volume B. Pitch C. Loudness D. Frequency

Last Answer : C. Loudness

In acoustics, if the volume of the room is 200 m3 then at what frequency the coefficient of absorption is measured? A. 120 kHz B. 120 Hz C. 100 Hz D. 150 Hz

Description : In acoustics, if the volume of the room is 200 m3 then at what frequency the coefficient of absorption is measured? A. 120 kHz B. 120 Hz C. 100 Hz D. 150 Hz

Last Answer : B. 120 Hz

______ meter is used to measure Illumination level a. Pyrometer b. Wattmeter c. Lux meter d. All

Description : ______ meter is used to measure Illumination level a. Pyrometer b. Wattmeter c. Lux meter d. All

Last Answer : Ans:- c. Lux meter

Answer the following S. No Statement Chose the correct answer OR Fill-in-the-blanks 1 Fyrite measures CO2, O2 and SO2 True/False 2 Ultrasonic Flow Meter uses the principle of____& ____ Fill in the blanks 3 Non Contact Infrared Thermometer cannot measure temperature of objects placed in hazardous places True/False 4 To measure the RPM of a Flywheel, ______ type of RPM meter is used and for a visible shaft-end _______ type of RPM meter is used. Fill in the blanks 5 In a switch yard, _____ instrument is used to identify the loose joints and terminations Fill in the blanks 6 Every Designated Consumer shall have its first energy audit conducted by ________ Energy Auditor within ______ months of

Description :  Answer the following S. No Statement Chose the correct  answer OR Fill-in-the-blanks 1 Fyrite measures CO2, O2 and SO2 True/False 2 Ultrasonic Flow Meter uses the principle of____& ____ Fill in the ... of RPM  meter is used and for a visible shaft-end _______ type of  RPM meter is used.

Last Answer : Sr  No Statement Chose the correct  answer OR Fill-in-the-blanks Solution 1 Fyrite measures CO2, O2 and  SO2 True/False False 2 Ultrasonic Flow Meter uses the  principle of____& ____ ... ]  10 In a gasification system the  reduction zone is above the  combustion zone True/False False

What is the phase coefficient in radians per unit length of a transmission line at the frequency of 10 MHz if the velocity of propagation is 2.5x108 m/s? A. 0.25 B. 2.5 C. 0.35 D. 3.5

Description : What is the phase coefficient in radians per unit length of a transmission line at the frequency of 10 MHz if the velocity of propagation is 2.5x108 m/s? A. 0.25 B. 2.5 C. 0.35 D. 3.5

Last Answer : A. 0.25

Which standard is utilized in intermodulation noise rates on PCM audio channels? A. CCIT Rec. G.151 B. CCIT Rec. G.172 C. CCIT Rec. G.190 D. CCIT Rec. G.190

Description : Which standard is utilized in intermodulation noise rates on PCM audio channels? A. CCIT Rec. G.151 B. CCIT Rec. G.172 C. CCIT Rec. G.190 D. CCIT Rec. G.190

Last Answer : B. CCIT Rec. G.172

A form of regenerative repeater for transmitting signals over a long cable received through a relay in a clearer form. A. Active generator B. Active repeater C. Interpolator D. Audio generator

Description : A form of regenerative repeater for transmitting signals over a long cable received through a relay in a clearer form. A. Active generator B. Active repeater C. Interpolator D. Audio generator

Last Answer : C. Interpolator

Where is the brightness control located in a TV? A. The audio section B. The video section C. The grid-cathode circuit D. The front panel

Description : Where is the brightness control located in a TV? A. The audio section B. The video section C. The grid-cathode circuit D. The front panel

Last Answer : A. The audio section

A test method of comparing two audio systems by switching inputs so that the same recording is heard in rapid succession over one given system and then the other. A. B test B. A test C. AB test D. C test

Description : A test method of comparing two audio systems by switching inputs so that the same recording is heard in rapid succession over one given system and then the other. A. B test B. A test C. AB test D. C test

Last Answer : C. AB test

What is the standard test tone used for audio measurements? A. 100 Hz B. 500 Hz C. 1000 Hz D. 2000 Hz

Description : What is the standard test tone used for audio measurements? A. 100 Hz B. 500 Hz C. 1000 Hz D. 2000 Hz

Last Answer : C. 1000 Hz

A 1 Mhz carrier is amplitude modulated by a pure 200-Hz audio test tone. Which of the following combinations of frequencies represent the total content of the AM signal? A. 1 MHz and 200 Hz B. 1 MHz and 1000.2 kHz C. 999.8 kHz, 1000 kHz, and 1000.2 kHz D. 999.8 kHz and 1000.2 kHz

Description : A 1 Mhz carrier is amplitude modulated by a pure 200-Hz audio test tone. Which of the following combinations of frequencies represent the total content of the AM signal? A. 1 MHz and 200 Hz B. 1 MHz and 1000.2 kHz C. 999.8 kHz, 1000 kHz, and 1000.2 kHz D. 999.8 kHz and 1000.2 kHz

Last Answer : C. 999.8 kHz, 1000 kHz, and 1000.2 kHz

________ is the method of encoding audio signals used in US standard 1544 kbit/s 24 channel PCM systems. A. Shannon’s law B. A-law C. Newton’s law D. Mu-law

Description : ________ is the method of encoding audio signals used in US standard 1544 kbit/s 24 channel PCM systems. A. Shannon’s law B. A-law C. Newton’s law D. Mu-law

Last Answer : D. Mu-law

How can receiver desensitizing be reduced? A. Increase the receiver bandwidth B. Ensure good RF shielding between the transmitter and receiver C. Increase the transmitter audio gain D. Decrease the receiver squelch, gain.

Description : How can receiver desensitizing be reduced? A. Increase the receiver bandwidth B. Ensure good RF shielding between the transmitter and receiver C. Increase the transmitter audio gain D. Decrease the receiver squelch, gain.

Last Answer : D. Decrease the receiver squelch, gain.

What is the effect in over modulated amplitude modulated radio broadcasting transmission? A. Interference to adjacent channel B. Higher fidelity C. Increase noise D. Higher audio signal

Description : What is the effect in over modulated amplitude modulated radio broadcasting transmission? A. Interference to adjacent channel B. Higher fidelity C. Increase noise D. Higher audio signal

Last Answer : A. Interference to adjacent channel

Atmospheric noise is less at severe frequencies above A. Audio level B. 30 MHz C. 10 GHz D. 1 GHz

Description : Atmospheric noise is less at severe frequencies above A. Audio level B. 30 MHz C. 10 GHz D. 1 GHz

Last Answer : B. 30 MHz

Which of the following is not a baseband signal modulation? A. RF carrier B. Video System C. Audio signal D. Binary coded pulses

Description : Which of the following is not a baseband signal modulation? A. RF carrier B. Video System C. Audio signal D. Binary coded pulses

Last Answer : A. RF carrier

Three audio waves with 100,200 and 300 volts amplitude respectively, simultaneously modulate a 450 volts carrier. What is the total percent of modulation of the AM wave? A. 69 % B. 115.5 % C. 50% D. 83%

Description : Three audio waves with 100,200 and 300 volts amplitude respectively, simultaneously modulate a 450 volts carrier. What is the total percent of modulation of the AM wave? A. 69 % B. 115.5 % C. 50% D. 83%

Last Answer : D. 83%

What is audio amplifier?

Description : What is audio amplifier?

Last Answer : The amplifier receives an input from signal source or from a transducer and gives out an amplified signal to the output device is called an audio amplifier. 

To measure radio frequency, the suitable frequency meter is

Last Answer : To measure radio frequency, the suitable frequency meter is heterodoxy frequency meter.

The speech coding rate in D-AMPS is ____. A. 8 kbps B. 13 kbps C. 15 kbps D. 20 kbps

Description : The speech coding rate in D-AMPS is ____. A. 8 kbps B. 13 kbps C. 15 kbps D. 20 kbps

Last Answer : A. 8 kbps

In GSM cellular system, the speech coding rate is ____. A. 13 kbps B. 8 kbps C. 15 kbps D. 20 kbps

Description : In GSM cellular system, the speech coding rate is ____. A. 13 kbps B. 8 kbps C. 15 kbps D. 20 kbps

Last Answer : A. 13 kbps

The range of speech power is ____. A. 1 – 10 watts B. 100 – 1000 milliwatts C. 10 – 100 milliwatts D. 10 – 1000 microwatts

Description : The range of speech power is ____. A. 1 – 10 watts B. 100 – 1000 milliwatts C. 10 – 100 milliwatts D. 10 – 1000 microwatts

Last Answer : 10 – 1000 microwatts

What is considered the most obvious conveyor of information? A. Sound B. Speech C. Music D. Noise

Description : What is considered the most obvious conveyor of information? A. Sound B. Speech C. Music D. Noise

Last Answer : B. Speech

The unit to measure the flow of water is - (1) Micro Mho (2) Ohm meter (3) Milli curie (4) Cusecs

Description : The unit to measure the flow of water is - (1) Micro Mho (2) Ohm meter (3) Milli curie (4) Cusecs

Last Answer : (4) Cusecs Explanation: The unit to measure the flow of water is cusecs. Cusecs is short form of Cubic feet per second.

The unit to measure the flow of water is (1) Micro Mho (2) Ohm meter (3) Milli curie (4) Cusecs

Description : The unit to measure the flow of water is (1) Micro Mho (2) Ohm meter (3) Milli curie (4) Cusecs

Last Answer : Cusecs

Newton is used to measure ______. (1) Speed (2) Volume (3) Force (4) Area

Description : Newton is used to measure ______. (1) Speed (2) Volume (3) Force (4) Area

Last Answer : (3) Force Explanation: The newton (N) is the International System of Units (SI) derived unit of force. It is named after Isaac Newton in recognition of his work on classical mechanics, specifically Newton's second law of motion.

The accelerometer is used as a transducer to measure earthquake in Richter scale. Its design is based on the principle that ______. (A) its natural frequency is very low in comparison to the frequency of vibration (B) its natural frequency is very high in comparison to the frequency of vibration (C) its natural frequency is equal to the frequency of vibration (D) measurement of vibratory motion is without any reference poin

Description : The accelerometer is used as a transducer to measure earthquake in Richter scale. Its design is based on the principle that ______. (A) its natural frequency is very low in comparison to the ... is equal to the frequency of vibration (D) measurement of vibratory motion is without any reference poin

Last Answer : (C) its natural frequency is equal to the frequency of vibration

What is the electrical wavelength of a 500 MHz signal? A. 60 centimeters B. 6 meters C. 0.06 meter D. 60 meters

Description : What is the electrical wavelength of a 500 MHz signal? A. 60 centimeters B. 6 meters C. 0.06 meter D. 60 meters

Last Answer : A. 60 centimeters

The noise output of a resistor is amplified by a noiseless amplifier having a gain of 60 and a bandwidth of 20 kHz. A meter connected at the output of the amplifier reads 1mV RMS. If the bandwidth of the amplifier is reduced to 5kHz, its gain remaining constant, what does the meter read now? A. 0.5 mV B. 0.5 µV C. 5.0 mV D. 5.0 µV

Description : The noise output of a resistor is amplified by a noiseless amplifier having a gain of 60 and a bandwidth of 20 kHz. A meter connected at the output of the amplifier reads 1mV RMS. If the bandwidth of the amplifier is reduced to ... does the meter read now? A. 0.5 mV B. 0.5 µV C. 5.0 mV D. 5.0 µV

Last Answer : A. 0.5 mV

You are measuring noise at a -6 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -59 dBm. This is _________ dBa0. A. 24 B. 12 C. 23 D. 32

Description : You are measuring noise at a -6 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -59 dBm. This is _________ dBa0. A. 24 B. 12 C. 23 D. 32

Last Answer : D. 32

You are measuring noise at a +3 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -57dBm. This is ________dBa0. A. 20 B. 15 C. 25 D. 17

Description : You are measuring noise at a +3 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -57dBm. This is ________dBa0. A. 20 B. 15 C. 25 D. 17

Last Answer : C. 25

You are measuring noise in a voice channel with a Lenkurt 601A, F1A weighting network and a flat meter. Your meter reads -47dBm. What is this reading in dBa? A. 77 dBa B. 35 dBa C. 38 dBa D. 32 dBa

Description : You are measuring noise in a voice channel with a Lenkurt 601A, F1A weighting network and a flat meter. Your meter reads -47dBm. What is this reading in dBa? A. 77 dBa B. 35 dBa C. 38 dBa D. 32 dBa

Last Answer : C. 38 dBa