‘L/mG’ is the expression for (A) Absorption factor (B) Brinkman number (C) Slope of operating line in absorber (D) Slope of operating line in stripper

‘L/mG’ is the expression for
(A) Absorption factor
(B) Brinkman number
(C) Slope of operating line in absorber
(D) Slope of operating line in stripper
by

1 Answer

Answer :

(A) Absorption factor
by

Related questions

Pick out the wrong statement: (A) Absorption factor is constant, when the equilibrium and operating lines are straight (B) In case of a stripper, the equilibrium curve is always below the operating line (C) In case of an absorber, the operating line is always above the equilibrium curve (D) In the absorption of low solubility gases, the liquid film is the controlling resistance

Description : Pick out the wrong statement: (A) Absorption factor is constant, when the equilibrium and operating lines are straight (B) In case of a stripper, the equilibrium curve is always below ... (D) In the absorption of low solubility gases, the liquid film is the controlling resistance

Last Answer : (B) In case of a stripper, the equilibrium curve is always below the operating line

Pick out the wrong statement. (A) The operating line always lies above the equilibrium solubility curve in case of a single component absorber (B) The operating line always lies below the equilibrium solubility curve in case of a single component stripper (C) The operating pressure in solvent extraction system should be below vapor pressures of all components (D) The solubility of a particular gas in ideal solution in any solvent is always the same

Description : Pick out the wrong statement. (A) The operating line always lies above the equilibrium solubility curve in case of a single component absorber (B) The operating line always lies below the equilibrium ... (D) The solubility of a particular gas in ideal solution in any solvent is always the same

Last Answer : (C) The operating pressure in solvent extraction system should be below vapor pressures of all components

. The absorption factor is defined as (where, L = liquid flow rate, G = gas flow rate and, m = slope of the equilibrium line). (A) L/mG (B) G/mL (C) mL/G (D) LG/m

Description : . The absorption factor is defined as (where, L = liquid flow rate, G = gas flow rate and, m = slope of the equilibrium line). (A) L/mG (B) G/mL (C) mL/G (D) LG/m

Last Answer : (A) L/mG

If G = insoluble gas in gas stream and L = non-volatile solvent in liquid stream, then the slope of the operating line for the absorber is (A) L/G (B) G/L (C) Always < 1 (D) None of these

Description : If G = insoluble gas in gas stream and L = non-volatile solvent in liquid stream, then the slope of the operating line for the absorber is (A) L/G (B) G/L (C) Always < 1 (D) None of these

Last Answer : (A) L/G

When both the fluids flow concurrently in an absorber, the slope of the operating line is (A) -ve (B) +ve (C) 1 (D) -1

Description : When both the fluids flow concurrently in an absorber, the slope of the operating line is (A) -ve (B) +ve (C) 1 (D) -1

Last Answer : (A) -ve

The slope of the operating line for a single component co-current absorber when plotted in terms of mole ratio units is (A) 0 (B) ∞ (C) -ve (D) +ve

Description : The slope of the operating line for a single component co-current absorber when plotted in terms of mole ratio units is (A) 0 (B) ∞ (C) -ve (D) +ve

Last Answer : (C) -ve

The minimum liquid rate to be used in an absorber corresponds to an operating line (A) Of slope = 1 (B) Of slope = 0.1 (C) Tangential to the equilibrium curve (D) None of these

Description : The minimum liquid rate to be used in an absorber corresponds to an operating line (A) Of slope = 1 (B) Of slope = 0.1 (C) Tangential to the equilibrium curve (D) None of these

Last Answer : (C) Tangential to the equilibrium curve

In a mixer, the quantity, (v. L/D) is termed as __________ number (where, v = longitudinal velocity of material, L = length of the mixer, D = diffusivity in axial mixing). (A) Weber (B) Peclet (C) Brinkman (D) Schmidt

Description : In a mixer, the quantity, (v. L/D) is termed as __________ number (where, v = longitudinal velocity of material, L = length of the mixer, D = diffusivity in axial mixing). (A) Weber (B) Peclet (C) Brinkman (D) Schmidt

Last Answer : (B) Peclet

In case of a desorber (stripper), the (A) Operating line always lies above the equilibrium curve (B) Operating line always lies below the equilibrium curve

Description : In case of a desorber (stripper), the (A) Operating line always lies above the equilibrium curve (B) Operating line always lies below the equilibrium curve

Last Answer : (B) Operating line always lies below the equilibrium curve

For stripping of a gas in a counter current stripper, the operating line (A) Lies above the equilibrium curve (B) Lies below the equilibrium curve (C) Can lie above or below the equilibrium curve (D) Is always parallel to the equilibrium curve

Description : For stripping of a gas in a counter current stripper, the operating line (A) Lies above the equilibrium curve (B) Lies below the equilibrium curve (C) Can lie above or below the equilibrium curve (D) Is always parallel to the equilibrium curve

Last Answer : (C) Can lie above or below the equilibrium curve

Desirable value of absorption factor in an absorber is (A) 1 (B) < 1 (C) > 1 (D) 0.5

Description : Desirable value of absorption factor in an absorber is (A) 1 (B) < 1 (C) > 1 (D) 0.5

Last Answer : (C) > 1

The operating line for an absorber is curved, when plotted in terms of (A) Mole fractions (B) Mole ratios (C) Partial pressure (D) Mass fractions

Description : The operating line for an absorber is curved, when plotted in terms of (A) Mole fractions (B) Mole ratios (C) Partial pressure (D) Mass fractions

Last Answer : (C) Partial pressure

In case of an absorber, the operating (A) Line always lies above the equilibrium curve (B) Line always lies below the equilibrium curve (C) Line can be either above or below the equilibrium curve (D) Velocity is more than the loading velocity

Description : In case of an absorber, the operating (A) Line always lies above the equilibrium curve (B) Line always lies below the equilibrium curve (C) Line can be either above or below the equilibrium curve (D) Velocity is more than the loading velocity

Last Answer : (A) Line always lies above the equilibrium curve

For an absorber, both equilibrium and operating line will be straight for (A) Concentrated solution and non-isothermal operation (B) Dilute solution and non-isothermal operation (C) Dilute solution and isothermal operation (D) Concentrated solution and isothermal operation

Description : For an absorber, both equilibrium and operating line will be straight for (A) Concentrated solution and non-isothermal operation (B) Dilute solution and non-isothermal operation (C) Dilute solution and isothermal operation (D) Concentrated solution and isothermal operation

Last Answer : (C) Dilute solution and isothermal operation

For a single component absorber, the operating line is straight only when plotted in term of __________ units. (A) Partial pressure (B) Mole ratio (C) Mole fraction (D) None of these

Description : For a single component absorber, the operating line is straight only when plotted in term of __________ units. (A) Partial pressure (B) Mole ratio (C) Mole fraction (D) None of these

Last Answer : (B) Mole ratio

H2S is being absorbed in a gas absorber unit. The height of the transfer unit based on the overall mass transfer coefficient on the gas side is 0.4 m. The equilibrium data is given by, y = 1.5 x. The bulk concentration of H2S has to be reduced from 0.05 to 0.001 mole fraction in the gas side. The height of the tower (in metres) corresponding to an operating line given by, y = 5x + 0.001 is (A) 2.0 (B) 1.56 (C) 1.0

Description : H2S is being absorbed in a gas absorber unit. The height of the transfer unit based on the overall mass transfer coefficient on the gas side is 0.4 m. The equilibrium data is given by, y = 1.5 x. The bulk concentration of H2S ... by, y = 5x + 0.001 is (A) 2.0 (B) 1.56 (C) 1.0

Last Answer : (A) 2.0

Absorption factor method is used to calculate the number of ideal stages, when (A) Operating line lies above the equilibrium line (B) Operating line lies below the equilibrium line (C) Both operating and equilibrium lines are parallel (D) Pressure drop in the column is very high

Description : Absorption factor method is used to calculate the number of ideal stages, when (A) Operating line lies above the equilibrium line (B) Operating line lies below the equilibrium line (C) Both operating and equilibrium lines are parallel (D) Pressure drop in the column is very high

Last Answer : (C) Both operating and equilibrium lines are parallel

The value of ‘L/mG’ ratio for economical absorption operation ranges from (A) 0.5 to 0.8 (B) 0.8 to 1.2 (C) 1.25 to 2.0 (D) 2.5 to 3.5

Description : The value of ‘L/mG’ ratio for economical absorption operation ranges from (A) 0.5 to 0.8 (B) 0.8 to 1.2 (C) 1.25 to 2.0 (D) 2.5 to 3.5

Last Answer : (C) 1.25 to 2.0

Absorption accompanied by heat evolution results in (A) Increased capacity of the absorber (B) Increase in equilibrium solubility (C) Decrease in equilibrium solubility (D) None of these

Description : Absorption accompanied by heat evolution results in (A) Increased capacity of the absorber (B) Increase in equilibrium solubility (C) Decrease in equilibrium solubility (D) None of these

Last Answer : (C) Decrease in equilibrium solubility

Which of the following is not concerned with the heat transfer? (A) Brinkman number (B) Stanton number(C) Schmidt number(D) Peclet number

Description : Which of the following is not concerned with the heat transfer? (A) Brinkman number (B) Stanton number (C) Schmidt number (D) Peclet number

Last Answer : (C) Schmidt number

A measure of the extent to which viscous heating is important relative to the heat flow resulting from the impressed temperature difference is represented by the __________ number. (A) Condensation (B) Grashoff (C) Stanton (D) Brinkman

Description : A measure of the extent to which viscous heating is important relative to the heat flow resulting from the impressed temperature difference is represented by the __________ number. (A) Condensation (B) Grashoff (C) Stanton (D) Brinkman

Last Answer : (D) Brinkman

N2 Re /NFr is called the __________ number. (A) Brinkman (B) Galileo (C) Archimedes (D) Euler

Description : N2 Re /NFr is called the __________ number. (A) Brinkman (B) Galileo (C) Archimedes (D) Euler

Last Answer : (B) Galileo

On nephelometry turbidity unit (NTU) is equal to the turbidity produced by (a) 1 mg SiO2 dissolved in 1 l of distilled water with the test being run according to absorption principle (b) 1 mg SiO2 dissolved in 1 l of distilled water with the test being run according t scattering principle (c) 1 mg Formazin dissolved in 1 l of distilled water with the test being run according to absorption principle (d) 1 mg Formazin dissolved in 1 l o f distilled water with the test being run according to scattering principle.

Description : On nephelometry turbidity unit (NTU) is equal to the turbidity produced by (a) 1 mg SiO2 dissolved in 1 l of distilled water with the test being run according to absorption principle (b) 1 ... Formazin dissolved in 1 l o f distilled water with the test being run according to scattering principle.

Last Answer : (d) 1 mg Formazin dissolved in 1 l o f distilled water with the test being run according to scattering principle.

The expression, y(1 - x)/x(1 - y) is for (A) Absorption factor (B) Relative volatility (C) Selectivity (D) Murphree efficiency

Description : The expression, y(1 - x)/x(1 - y) is for (A) Absorption factor (B) Relative volatility (C) Selectivity (D) Murphree efficiency

Last Answer : (B) Relative volatility

The individual mass transfer co-efficients (moles/m2s) for absorption of a solute from a gas mixture into a liquid solvent are, KL = 4.5 and KG = 1.5. The slope of the equilibrium line is 3. Which of the following resistance (s) is (are) controlling? (A) Liquid side (B) Gas side (C) Interfacial (D) Both liquid and gas side

Description : The individual mass transfer co-efficients (moles/m2s) for absorption of a solute from a gas mixture into a liquid solvent are, KL = 4.5 and KG = 1.5. The slope of the equilibrium line is 3. Which of ... A) Liquid side (B) Gas side (C) Interfacial (D) Both liquid and gas side

Last Answer : (B) Gas side

Cooling water is required for following equipment in ammonia absorption plant (a) condenser (b) evaporator (c) condenser and absorber (d) condenser, absorber and separator (rectifier).

Description : Cooling water is required for following equipment in ammonia absorption plant (a) condenser (b) evaporator (c) condenser and absorber (d) condenser, absorber and separator (rectifier).

Last Answer : Ans: d

A porous material is far more efficient at high than low frequency absorption. How to improve sound absorption at lower frequencies using this absorber? A. Increase the thickness B. Decrease the thickness C. Mount with and airspace behind D. Both A and C above

Description : A porous material is far more efficient at high than low frequency absorption. How to improve sound absorption at lower frequencies using this absorber? A. Increase the thickness B. Decrease the thickness C. Mount with and airspace behind D. Both A and C above

Last Answer : D. Both A and C above

What absorber in which efficient absorption is only possible over a very narrow band approaching 1.0 (total absorption)? A. Porous material B. Helmholtz resonator C. Panel Absorber D. Membrane absorber

Description : What absorber in which efficient absorption is only possible over a very narrow band approaching 1.0 (total absorption)? A. Porous material B. Helmholtz resonator C. Panel Absorber D. Membrane absorber

Last Answer : B. Helmholtz resonator

A body will behave as an “ideal black body” when it acts as: a) A perfect absorber b) A perfect radiator c) A body to have absorption power equal to one d) All of the above

Description : A body will behave as an “ideal black body” when it acts as: a) A perfect absorber b) A perfect radiator c) A body to have absorption power equal to one d) All of the above

Last Answer : d) All of the above

As the reflux ratio in a distillation column is increased from the minimum, the (A) Slope of the operating line in stripping section decreases (B) Number of plates decreases very slowly first and then more and more rapidly (C) Total cost first decreases and then increases (D) Liquid flow increases while the vapor flow decreases for a system

Description : As the reflux ratio in a distillation column is increased from the minimum, the (A) Slope of the operating line in stripping section decreases (B) Number of plates decreases very slowly first ... decreases and then increases (D) Liquid flow increases while the vapor flow decreases for a system

Last Answer : (C) Total cost first decreases and then increases

On moving the feed line (q-line) from saturated liquid feed (vertical position) to saturated vapor feed (horizontal feed), if the slope of both the operating lines are to be increased, then it will result in (A) Greater degree of separation with a fixed number of trays (B) Increased reboiler load

Description : On moving the feed line (q-line) from saturated liquid feed (vertical position) to saturated vapor feed (horizontal feed), if the slope of both the operating lines are to be increased, then it will result in (A) Greater degree of separation with a fixed number of trays (B) Increased reboiler load

Last Answer : (C) Increased reflux ratio

In a packed absorption tower, if the equilibrium and operating lines are both straight lines, then the ratio, HETP/HTUOG __________ the absorption factor. (A) Increases with increase in (B) Is one at unity value of (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : In a packed absorption tower, if the equilibrium and operating lines are both straight lines, then the ratio, HETP/HTUOG __________ the absorption factor. (A) Increases with increase in (B) Is one at unity value of (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Pick out the correct statement. (A) The slope of the stripping line is always less than unity (B) For a given separation in a binary distillation column, with increase in reflux ratio (above the minimum reflux ratio), the fixed cost of the distillation column first increases and then decreases (C) In Ponchon-Savarit method of no. of theoretical plate determination, the stripping and rectifying operating lines are vertical at total reflux (D) Kremser-Brown-Souder's equation is used to calculate the efficiency of a plate tower

Description : Pick out the correct statement. (A) The slope of the stripping line is always less than unity (B) For a given separation in a binary distillation column, with increase in reflux ratio ( ... (D) Kremser-Brown-Souder's equation is used to calculate the efficiency of a plate tower

Last Answer : C) In Ponchon-Savarit method of no. of theoretical plate determination, the stripping and rectifying operating lines are vertical at total reflux

For water-ethanol system, the minimum reflux ratio (A) Is computed from the slope of the upper operating line that is tangent to the equilibrium curve (B) Is computed from the intercept of the operating line (C) Cannot be computed (D) Is the optimum reflux ratio

Description : For water-ethanol system, the minimum reflux ratio (A) Is computed from the slope of the upper operating line that is tangent to the equilibrium curve (B) Is computed from the intercept of the operating line (C) Cannot be computed (D) Is the optimum reflux ratio

Last Answer : (A) Is computed from the slope of the upper operating line that is tangent to the equilibrium curve

A four wheel truck or whose operating weight is 12000 kg is pulled along a road having a rising slope of 2% at a uniform speed. Assume grade resistance factor = 10 kg/tonne. The tension in the tow cable is 720 kg. The rolling resistance of the road will be (A) 20 kg/tonne (B) 30 kg/tonne (C) 40 kg/tonne (D) 50 kg/tonne

Description : A four wheel truck or whose operating weight is 12000 kg is pulled along a road having a rising slope of 2% at a uniform speed. Assume grade resistance factor = 10 kg/tonne. The tension in the tow cable is 720 kg. The ... will be (A) 20 kg/tonne (B) 30 kg/tonne (C) 40 kg/tonne (D) 50 kg/tonne

Last Answer : (C) 40 kg/tonne

Pick out the wrong statement (A) Co-current absorbers are usually used, when the gas to be dissolved in the liquid is a pure substance (B) In case of gas absorption, HETP is equal to HTU, when both the operating line & the equilibrium lines are parallel (C) Hatta number is important in case of gas absorption with chemical reaction (D) In actual practice, absorption is an endothermic process, while stripping is an exothermic process

Description : Pick out the wrong statement (A) Co-current absorbers are usually used, when the gas to be dissolved in the liquid is a pure substance (B) In case of gas absorption, HETP is ... reaction (D) In actual practice, absorption is an endothermic process, while stripping is an exothermic process

Last Answer : (D) In actual practice, absorption is an endothermic process, while stripping is an exothermic process

. In centrifugal pendulum absorber , the natural frequency in cycle per second can be given by A Fn =N √(R/L) B Fn =1/N √(R/L) C Fn =N/2 √(R/L) D Fn =N2 √(R/L)

Description : . In centrifugal pendulum absorber , the natural frequency in cycle per second can be given by A Fn =N √(R/L) B Fn =1/N √(R/L) C Fn =N/2 √(R/L) D Fn =N2 √(R/L)

Last Answer : A Fn =N √(R/L)

In centrifugal pendulum absorber , the natural frequency in cycle per second can be given by A) Fn =N √(R/L) B) Fn =1/N √(R/L) C) Fn =N/2 √(R/L) D) Fn =N2 √(R/L)

Description : In centrifugal pendulum absorber , the natural frequency in cycle per second can be given by A) Fn =N √(R/L) B) Fn =1/N √(R/L) C) Fn =N/2 √(R/L) D) Fn =N2 √(R/L)

Last Answer : A) Fn =N √(R/L)

Following the six-tenth factor rule, if a log-log plot of capacity of the equipment vs. cost of the equipment is made, then a straight line is obtained, whose slope is equal to (A) 0.1 (B) 0.6 (C) 0.2 (D) 0.8

Description : Following the six-tenth factor rule, if a log-log plot of capacity of the equipment vs. cost of the equipment is made, then a straight line is obtained, whose slope is equal to (A) 0.1 (B) 0.6 (C) 0.2 (D) 0.8

Last Answer : (B) 0.6

Should I tell people that I'm a stripper? Why or why not?

Description : Should I tell people that I'm a stripper? Why or why not?

Last Answer : No. Secrets destroy intimacy with all you keep them from. If you really feel okay about your choice to strip then you have nothing to hide. Lying is never good, especially right out of the gate ... job that doesn't involve sexually exploiting yourself for a few bucks. You're better than that right?

How much money would it require for you to be a stripper?

Description : How much money would it require for you to be a stripper?

Last Answer : I should qualify this. You’re relatively young, don’t do well in school, and just don’t care about how seedy it is.

10 coats of old paint on metal pillars - options: chemical stripper, sander or heat gun?

Description : 10 coats of old paint on metal pillars - options: chemical stripper, sander or heat gun?

Last Answer : Probably all three…... and then call in the specialists tidy up the mess you made.

Would you date a stripper/exotic dancer ?

Description : Would you date a stripper/exotic dancer ?

Last Answer : Sure, it;s just their job, its not who they are.

If a stripper gets breast implants can she write it off on her taxes as a business expense?

Description : If a stripper gets breast implants can she write it off on her taxes as a business expense?

Last Answer : I doubt it.

If you were a stripper/poledancer, what song would you strip/dance to?

Description : If you were a stripper/poledancer, what song would you strip/dance to?

Last Answer : I think me poledancing would cause hysteria as well as nausea, but I’ve always thought She Rides by Danzig and You Can Leave Your Hat On by Joe Cocker were the 2 absolute best songs for it.

Would anyone here date a stripper?

Description : Would anyone here date a stripper?

Last Answer : answer:I did and at first it was fun. So i thought i could handle it. The more I got into her the more it bothered me. It got to the point were she had to make a decision…me or stripping. Its a slippery slope my friend

Looking for customer reviews for Glass Science Glass Scrub Auto Glass Stripper repair oakland in Anchorage, AK?

Description : Looking for customer reviews for Glass Science Glass Scrub Auto Glass Stripper repair oakland in Anchorage, AK?

Last Answer : According to several sites the reviews of this companies are pretty mixed when it comes to services and lateness.

How do you get a stripper license in Florida?

Description : How do you get a stripper license in Florida?

Last Answer : I would suggest you go to a stripper bar and ask. I am sure there is something better you can do with your life than strip for men.

The rate expression for a heterogeneous catalytic reaction is given by, - rA = K.KA PA(1 + KA.PA + KR.PR), where K is surface reaction rate constant and KA and KR are absorption equilibrium constants of A and R respectively. If KR PR >> (1 + KA PA), the apparent activation energy EA is equal to (given E is the activation energy for the reaction and ΔHR and ΔHA are the activation energies of adsorption of R and A) (A) E (B) E + ΔHA (C) E + ΔHA - ΔHR ) (D) ΔHA + ΔHR

Description : The rate expression for a heterogeneous catalytic reaction is given by, - rA = K.KA PA(1 + KA.PA + KR.PR), where K is surface reaction rate constant and KA and KR are absorption equilibrium constants of A and R respectively. If KR PR ... R and A) (A) E (B) E + ΔHA (C) E + ΔHA - ΔHR ) (D) ΔHA + ΔHR

Last Answer : (C) E + ΔHA - ΔHR )