In a mixer, the quantity, (v. L/D) is termed as __________ number (where, v = longitudinal velocity of material, L = length of the mixer, D = diffusivity in axial mixing). (A) Weber (B) Peclet (C) Brinkman (D) Schmidt

In a mixer, the quantity, (v. L/D) is termed as __________ number
(where, v = longitudinal velocity of material, L = length of the mixer, D =
diffusivity in axial mixing).
(A) Weber
(B) Peclet
(C) Brinkman
(D) Schmidt
by

1 Answer

Answer :

(B) Peclet
by

Related questions

Which of the following is not concerned with the heat transfer? (A) Brinkman number (B) Stanton number(C) Schmidt number(D) Peclet number

Description : Which of the following is not concerned with the heat transfer? (A) Brinkman number (B) Stanton number (C) Schmidt number (D) Peclet number

Last Answer : (C) Schmidt number

. (NSh /NRe .NSc ) is termed in mass transfer operation as the (A) Stanton number (B) Peclet number (C) Thermal diffusivity (D) Momentum diffusivity

Description : . (NSh /NRe .NSc ) is termed in mass transfer operation as the (A) Stanton number (B) Peclet number (C) Thermal diffusivity (D) Momentum diffusivity

Last Answer : (A) Stanton number

Corresponding to Prandtl number in heat transfer, the dimensionless group in mass transfer is the __________ number. (A) Schmidt (B) Sherwood (C) Peclet (D) Stanton

Description : Corresponding to Prandtl number in heat transfer, the dimensionless group in mass transfer is the __________ number. (A) Schmidt (B) Sherwood (C) Peclet (D) Stanton

Last Answer : (A) Schmidt

Corresponding to Nusselt number in heat transfer, the dimensionless group in mass transfer is the __________ number. (A) Sherwood (B) Schmidt (C) Peclet (D) Stanton

Description : Corresponding to Nusselt number in heat transfer, the dimensionless group in mass transfer is the __________ number. (A) Sherwood (B) Schmidt (C) Peclet (D) Stanton

Last Answer : (A) Sherwood

The ratio of kinematic viscosity to thermal diffusivity is called the __________ number. (A) Peclet (B) Prandtl (C) Stanton (D) Nusselt

Description : The ratio of kinematic viscosity to thermal diffusivity is called the __________ number. (A) Peclet (B) Prandtl (C) Stanton (D) Nusselt

Last Answer : (B) Prandtl

(NRe . NSc ) is termed in mass transfer operation as the __________ number. (A) Stanton (B) Sherwood (C) Peclet (D) None of these

Description : (NRe . NSc ) is termed in mass transfer operation as the __________ number. (A) Stanton (B) Sherwood (C) Peclet (D) None of these

Last Answer : (C) Peclet

In physical terms, Schmidt number means (A) Thermal diffusivity/mass diffusivity(B) Thermal diffusivity/momentum diffusivity(C) Momentum diffusivity/mass diffusivity(D) Mass diffusivity/thermal diffusivity

Description : In physical terms, Schmidt number means (A) Thermal diffusivity/mass diffusivity (B) Thermal diffusivity/momentum diffusivity (C) Momentum diffusivity/mass diffusivity (D) Mass diffusivity/thermal diffusivity

Last Answer : (C) Momentum diffusivity/mass diffusivity

The Schmidt number which is defined as, μ/ρ D, is the ratio of the (A) Momentum diffusivity to the mass diffusivity (B) Thermal diffusivity to the mass diffusivity (C) Momentum diffusivity to the thermal diffusivity (D) None of these

Description : The Schmidt number which is defined as, μ/ρ D, is the ratio of the (A) Momentum diffusivity to the mass diffusivity (B) Thermal diffusivity to the mass diffusivity (C) Momentum diffusivity to the thermal diffusivity (D) None of these

Last Answer : (A) Momentum diffusivity to the mass diffusivity

NRe . NPr ) (D/L) is called the __________ number (A) Peclet (B) Stanton (C) Graetz (D) None of these

Description : NRe . NPr ) (D/L) is called the __________ number (A) Peclet (B) Stanton (C) Graetz (D) None of these

Last Answer : (C) Graetz

In a semi-batch reactor, (A) Mixing takes place in axial direction only (B) Velocity of reaction can be controlled (C) Condition similar to plug flow reactor exists (D) Residence time is constant

Description : In a semi-batch reactor, (A) Mixing takes place in axial direction only (B) Velocity of reaction can be controlled (C) Condition similar to plug flow reactor exists (D) Residence time is constant

Last Answer : (B) Velocity of reaction can be controlled

‘L/mG’ is the expression for (A) Absorption factor (B) Brinkman number (C) Slope of operating line in absorber (D) Slope of operating line in stripper

Description : ‘L/mG’ is the expression for (A) Absorption factor (B) Brinkman number (C) Slope of operating line in absorber (D) Slope of operating line in stripper

Last Answer : (A) Absorption factor

In an ideal tubular-flow reactor (A) There is no mixing in longitudinal direction (B) Mixing takes place in radial direction (C) There is a uniform velocity across the radius (D) All (A), (B) and (C)

Description : In an ideal tubular-flow reactor (A) There is no mixing in longitudinal direction (B) Mixing takes place in radial direction (C) There is a uniform velocity across the radius (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In small columns, local efficiency is larger than Murphree efficiency; in large columns local efficiency is smaller than Murphree efficiency (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s (D) The concentration and hydrodynamic boundary layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Description : Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In ... layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Last Answer : (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s

Weber number is significant and is concerned with the (A) Solid-liquid mixing (B) Liquid-liquid mixing (C) Dispersion of liquid in liquid (D) Suspension of solid in liquid

Description : Weber number is significant and is concerned with the (A) Solid-liquid mixing (B) Liquid-liquid mixing (C) Dispersion of liquid in liquid (D) Suspension of solid in liquid

Last Answer : (C) Dispersion of liquid in liquid

A measure of the extent to which viscous heating is important relative to the heat flow resulting from the impressed temperature difference is represented by the __________ number. (A) Condensation (B) Grashoff (C) Stanton (D) Brinkman

Description : A measure of the extent to which viscous heating is important relative to the heat flow resulting from the impressed temperature difference is represented by the __________ number. (A) Condensation (B) Grashoff (C) Stanton (D) Brinkman

Last Answer : (D) Brinkman

N2 Re /NFr is called the __________ number. (A) Brinkman (B) Galileo (C) Archimedes (D) Euler

Description : N2 Re /NFr is called the __________ number. (A) Brinkman (B) Galileo (C) Archimedes (D) Euler

Last Answer : (B) Galileo

Cp /Cv is termed as (A) Adiabatic constant (B) Mach number (C) Weber number (D) Prandtl number

Description : Cp /Cv is termed as (A) Adiabatic constant (B) Mach number (C) Weber number (D) Prandtl number

Last Answer : (A) Adiabatic constan

Mixing of light fine powder such as insecticides is done by (A) Banbury mixer (B) Pug mill (C) Impact wheels (D) Kneader

Description : Mixing of light fine powder such as insecticides is done by (A) Banbury mixer (B) Pug mill (C) Impact wheels (D) Kneader

Last Answer : (C) Impact wheels

Which of the following clay mixing devices is vacuum operated for deairation of clay? (A) Banbury mixer (B) Pug mill (C) Muller-mixer (D) None of these

Description : Which of the following clay mixing devices is vacuum operated for deairation of clay? (A) Banbury mixer (B) Pug mill (C) Muller-mixer (D) None of these

Last Answer : (B) Pug mill

Mixing mechanism employed in a pan mixer is by (A) Mulling (B) Kneading (C) Dispersion (D) None of these

Description : Mixing mechanism employed in a pan mixer is by (A) Mulling (B) Kneading (C) Dispersion (D) None of these

Last Answer : (A) Mulling

Pick out the wrong statement. (A) The vessel dispersion number (D/UL) for plug flow and mixed flow approaches zero and infinity respectively (B) Space time in a flow reactor is a measure of its capacity and is equal to the residence time when the density of reaction mixture is constant (C) Mixed reactor is always smaller than the plug flow reactor for all positive reaction orders for a particular duty (D) In an ideal tubular flow reactor, mixing takes place in radial direction and there is no mixing in longitudinal direction

Description : Pick out the wrong statement. (A) The vessel dispersion number (D/UL) for plug flow and mixed flow approaches zero and infinity respectively (B) Space time in a flow reactor is a ... ideal tubular flow reactor, mixing takes place in radial direction and there is no mixing in longitudinal direction

Last Answer : (C) Mixed reactor is always smaller than the plug flow reactor for all positive reaction orders for a particular duty

__________ number indicates the ratio of the rates of the heat and mass transfer incase of a cooling tower. (A) Sherwood (B) Stanton (C) Lewis (D) Peclet

Description : __________ number indicates the ratio of the rates of the heat and mass transfer incase of a cooling tower. (A) Sherwood (B) Stanton (C) Lewis (D) Peclet

Last Answer : (C) Lewis

The equation, (h.D/K) is called the __________ number. (A) Nusselt (B) Peclet (C) Rayleigh (D) Grashoff

Description : The equation, (h.D/K) is called the __________ number. (A) Nusselt (B) Peclet (C) Rayleigh (D) Grashoff

Last Answer : (A) Nusselt

Which mixer is best for mixing monitors?

Description : Which mixer is best for mixing monitors?

Last Answer : Allen and Heath make a mixer that is just perfect for mixing monitors.

What are the equipments used for mixing of liquids? Give in detail about ‘Propeller Mixer’.

Description : What are the equipments used for mixing of liquids? Give in detail about ‘Propeller Mixer’.

Last Answer : Equipments used for mixing of Liquids i .Propeller mixer ii .Turbine mixer iii .Paddle mixer Propeller Mixers Construction: .It consists of vessel and propeller, Propeller usually operates at ... : Application: It is used for mixing of liquids having low viscosity.

Paddle agitator (A) Is suitable for mixing low viscosity liquids (B) Produces axial flow (C) Moves at very high speed (D) None of these

Description : Paddle agitator (A) Is suitable for mixing low viscosity liquids (B) Produces axial flow (C) Moves at very high speed (D) None of these

Last Answer : (A) Is suitable for mixing low viscosity liquids

A propeller agitator (A) Produces mainly axial flow (B) Is used for mixing high viscosity pastes (C) Runs at very slow speed (2 rpm) (D) All (A), (B) and (C)

Description : A propeller agitator (A) Produces mainly axial flow (B) Is used for mixing high viscosity pastes (C) Runs at very slow speed (2 rpm) (D) All (A), (B) and (C)

Last Answer : (A) Produces mainly axial flow

In a counter-current extractor, as the axial mixing increases, the extraction efficiency (A) Increases (B) Decreases (C) Remains unchanged (D) Depends on the pressure of the system

Description : In a counter-current extractor, as the axial mixing increases, the extraction efficiency (A) Increases (B) Decreases (C) Remains unchanged (D) Depends on the pressure of the system

Last Answer : (B) Decreases

In most of the mechanically agitated liquid-liquid extractors, baffles or horizontal compartmental plates are provided, which helps in (A) Reducing the axial mixing (B) Increasing the rate of extraction (C) Maintaining the concentration difference between the two phases (D) All 'a', 'b' & 'c'

Description : In most of the mechanically agitated liquid-liquid extractors, baffles or horizontal compartmental plates are provided, which helps in (A) Reducing the axial mixing (B) Increasing the rate of extraction (C) Maintaining the concentration difference between the two phases (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

Propellers are (A) Axial flow mixers (B) Low speed impeller (C) Used for mixing liquids of high viscosity (D) Radial flow mixers

Description : Propellers are (A) Axial flow mixers (B) Low speed impeller (C) Used for mixing liquids of high viscosity (D) Radial flow mixers

Last Answer : (A) Axial flow mixers

A backmix reactor (A) Is same as plug-flow reactor (B) Is same as ideal stirred tank reactor (C) Employs mixing in axial direction only (D) Is most suitable for gas phase reaction

Description : A backmix reactor (A) Is same as plug-flow reactor (B) Is same as ideal stirred tank reactor (C) Employs mixing in axial direction only (D) Is most suitable for gas phase reaction

Last Answer : (B) Is same as ideal stirred tank reactor

A plug-flow reactor is characterised by (A) High capacity (B) Presence of axial mixing (C) Presence of lateral mixing (D) Constant composition and temperature of reaction mixture

Description : A plug-flow reactor is characterised by (A) High capacity (B) Presence of axial mixing (C) Presence of lateral mixing (D) Constant composition and temperature of reaction mixture

Last Answer : (C) Presence of lateral mixing

Pick out the wrong statement pertaining to the turbine agitator. (A) Recommended peripheral speed for the turbine agitator is 200-250 metres/minute (B) Pitched blade turbine agitator gives only radial flow with complete absence of the axial flow (C) Generally, the diameter of the agitator is kept between l/3rd to l/6th of the tank diameter while the blade length is l/4th of agitator diameter (with central disc, it is l/8th of the agitator diameter)

Description : Pick out the wrong statement pertaining to the turbine agitator. (A) Recommended peripheral speed for the turbine agitator is 200-250 metres/minute (B) Pitched blade turbine agitator gives only radial flow with ... l/4th of agitator diameter (with central disc, it is l/8th of the agitator diameter)

Last Answer : (B) Pitched blade turbine agitator gives only radial flow with complete absence of the axial flow

Batching refers to (A) Controlling the total quantity at each batch (B) Weighing accurately, the quantity of each material for a job before mixing (C) Controlling the quantity of each material into each batch (D) Adjusting the water to be added in each batch according to the moisture content of the materials being mixed in the batch

Description : Batching refers to (A) Controlling the total quantity at each batch (B) Weighing accurately, the quantity of each material for a job before mixing (C) Controlling the quantity of each material ... be added in each batch according to the moisture content of the materials being mixed in the batch

Last Answer : (C) Controlling the quantity of each material into each batch

The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of 4 tonnes at the centre. The maximum stress in the bottom most fibre at the mid span section, is (A) 13.33 kg/cm2 tensile (B) 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Description : The section modulus of a rectangular light beam 25 metres long is 12.500 cm3 . The beam is simply supported at its ends and carries a longitudinal axial tensile load of 10 tonnes in addition to a point load of ... 13.33 kg/cm2 compressive (C) 26.67 kg/cm2 tensile (D) 26.67 kg/cm2 compressive

Last Answer : (C) 26.67 kg/cm2 tensile

A metal rod of length l cuts across a uniform magnetic field B with a velocity v. If the resistance of the circuit of which the rod forms a part is r,

Description : A metal rod of length l cuts across a uniform magnetic field B with a velocity v. If the resistance of the circuit of which the rod forms a part is r,

Last Answer : A metal rod of length l cuts across a uniform magnetic field B with a velocity v. If the resistance of the circuit of ... lv)/(r)` D. `(Blv^(2))/(r)`

In the figure shown, a conducting wire PQ of length l=1m, is moved in a uniform magnetic field B=4T with constant velocity v=2m/s towards right. Given

Description : In the figure shown, a conducting wire PQ of length l=1m, is moved in a uniform magnetic field B=4T with constant velocity v=2m/s towards right. Given

Last Answer : In the figure shown, a conducting wire PQ of length l=1m, is moved in a uniform magnetic field B=4T with ... P_(2) = 32 J//s` D. None of these

In the figure shown, a conducting wire PQ of length l=1m, is moved in a uniform magnetic field B=4T with constant velocity v=2m/s towards right. Given

Description : In the figure shown, a conducting wire PQ of length l=1m, is moved in a uniform magnetic field B=4T with constant velocity v=2m/s towards right. Given

Last Answer : In the figure shown, a conducting wire PQ of length l=1m, is moved in a uniform magnetic field B=4T with constant ... `16 N` C. `24 N` D. `32 N`

In the figure shown, a conducting wire PQ of length l=1m, is moved in a uniform magnetic field B=4T with constant velocity v=2m/s towards right. Given

Description : In the figure shown, a conducting wire PQ of length l=1m, is moved in a uniform magnetic field B=4T with constant velocity v=2m/s towards right. Given

Last Answer : In the figure shown, a conducting wire PQ of length l=1m, is moved in a uniform magnetic field B=4T with constant ... `0` B. `2A` C. `4A` D. `6A`

According to Darcy's formula, the loss of head due to friction in the pipe is (where f = Darcy's coefficient, l = Length of pipe, v = Velocity of liquid in pipe, and d = Diameter of pipe) (A) flv²/2gd (B) flv²/gd (C) 3flv²/2gd (D) 4flv²/2gd

Description : According to Darcy's formula, the loss of head due to friction in the pipe is (where f = Darcy's coefficient, l = Length of pipe, v = Velocity of liquid in pipe, and d = Diameter of pipe) (A) flv²/2gd (B) flv²/gd (C) 3flv²/2gd (D) 4flv²/2gd

Last Answer : Answer: Option D

The Knudsen diffusivity is dependent on the (A) Molecular velocity only (B) Pore radius of the catalyst only (C) Molecular mean free path only (D) Molecular velocity and pore radius of the catalyst

Description : The Knudsen diffusivity is dependent on the (A) Molecular velocity only (B) Pore radius of the catalyst only (C) Molecular mean free path only (D) Molecular velocity and pore radius of the catalyst

Last Answer : (D) Molecular velocity and pore radius of the catalyst

The dimension of diffusivity is same as that of the (A) Density (B) Molal concentration (C) Kinematic viscosity (D) Velocity head

Description : The dimension of diffusivity is same as that of the (A) Density (B) Molal concentration (C) Kinematic viscosity (D) Velocity head

Last Answer : (C) Kinematic viscosity

In fluid flow, and heat and mass transfer, one encounters (i) kinematic velocity (μ), (ii) molecular diffusivity (θ) and thermal diffusivity (α). The units of these quantities are. (A) μ , α and θ all have units of m/s (B) μ , α and θ all have units of m2/s (C) α and θ have units of m2/s, while μ has unit of m/s (D) α and θ have units of m/s, while μ has unit of m2/s

Description : In fluid flow, and heat and mass transfer, one encounters (i) kinematic velocity (μ), (ii) molecular diffusivity (θ) and thermal diffusivity (α). The units of these quantities are. (A) μ , α and θ all have units of m/ ... μ has unit of m/s (D) α and θ have units of m/s, while μ has unit of m2/s

Last Answer : Option C

Vegetable oils contain large quantity of glycerides of unsaturated acids. When the vegetable oils contain high amount of saturated fatty acids, it is termed as __________ oil. (A) Drying (B) Semi-drying (C) Non-drying (D) None of these

Description : Vegetable oils contain large quantity of glycerides of unsaturated acids. When the vegetable oils contain high amount of saturated fatty acids, it is termed as __________ oil. (A) Drying (B) Semi-drying (C) Non-drying (D) None of these

Last Answer : (C) Non-drying

Pick up the correct statement from the following: (A) Alexander Parkes, a Scottish chemist prepared a hard material by mixing camphor and alcohol with nitro cellulose and called it, as Parkesite (B) Dr. L. Bakeland, a Belgian scientist prepared a product known as Bakelite (C) Pollark, an Austrian scientist prepared a substance from urea and formaldehyde and called it Plastic (D) All the above

Description : Pick up the correct statement from the following: (A) Alexander Parkes, a Scottish chemist prepared a hard material by mixing camphor and alcohol with nitro cellulose and called it, as Parkesite ... prepared a substance from urea and formaldehyde and called it Plastic (D) All the above

Last Answer : Answer: Option D

The ratio of inertial forces to gravity forces is called the __________ number. (A) Mach (B) Froude (C) Euler (D) Weber

Description : The ratio of inertial forces to gravity forces is called the __________ number. (A) Mach (B) Froude (C) Euler (D) Weber

Last Answer : (B) Froude

Ratio of pressure and inertia force gives __________ number. (A) Weber (B) Mach (C) Euler (D) Froude

Description : Ratio of pressure and inertia force gives __________ number. (A) Weber (B) Mach (C) Euler (D) Froude

Last Answer : (C) Euler

The ratio of inertial forces to elastic forces is called the __________ number. (A) Reynolds (B) Mach (C) Euler (D) Weber

Description : The ratio of inertial forces to elastic forces is called the __________ number. (A) Reynolds (B) Mach (C) Euler (D) Weber

Last Answer : (B) Mach

The ratio of inertial forces to elastic forces is called the __________ number. (A) Reynolds (B) Mach (C) Euler (D) Weber

Description : The ratio of inertial forces to elastic forces is called the __________ number. (A) Reynolds (B) Mach (C) Euler (D) Weber

Last Answer : (B) Mach

Weber number is the ratio of inertial force to __________ force. (A) Surface tension (B) Gravity (C) Viscous (D) Elastic

Description : Weber number is the ratio of inertial force to __________ force. (A) Surface tension (B) Gravity (C) Viscous (D) Elastic

Last Answer : (A) Surface tension