Gravity stamp mill is meant for the __________ crushing. (A) Primary (B) Intermediate (C) Fine (D) Ultrafine

Gravity stamp mill is meant for the __________ crushing.
(A) Primary
(B) Intermediate
(C) Fine
(D) Ultrafine
by

1 Answer

Answer :

(C) Fine
by

Related questions

In a size reduction crushing operation, feed size is 100 to 300 mm. while the product size is 10 to 50 mm. This is a case of the __________ crushing. (A) Primary (B) Secondary (C) Fine (D) Ultrafine

Description : In a size reduction crushing operation, feed size is 100 to 300 mm. while the product size is 10 to 50 mm. This is a case of the __________ crushing. (A) Primary (B) Secondary (C) Fine (D) Ultrafine

Last Answer : (B) Secondary

In a size reduction crushing operation, feed size is 300 to 1500 mm while the product size is 100 to 300 mm. This is a case of the __________ crushing. (A) Secondary (B) Fine (C) Primary (D) Ultrafine

Description : In a size reduction crushing operation, feed size is 300 to 1500 mm while the product size is 100 to 300 mm. This is a case of the __________ crushing. (A) Secondary (B) Fine (C) Primary (D) Ultrafine

Last Answer : (C) Primary

Colloidal mills are used for __________ grinding. (A) Coarse (B) Intermediate (C) Fine (D) Ultrafine

Description : Colloidal mills are used for __________ grinding. (A) Coarse (B) Intermediate (C) Fine (D) Ultrafine

Last Answer : (D) Ultrafine

Ball mill is used for (A) Crushing (B) Coarse grinding (C) Fine grinding (D) Attrition

Description : Ball mill is used for (A) Crushing (B) Coarse grinding (C) Fine grinding (D) Attrition

Last Answer : (C) Fine grinding

Use of 'grinding aids' is done in __________ grinding. (A) Dry (B) Wet (C) Ultrafine (D) Intermediate

Description : Use of 'grinding aids' is done in __________ grinding. (A) Dry (B) Wet (C) Ultrafine (D) Intermediate

Last Answer : (A) Dry

In a size reduction crushing operation, the feed size is 10 to 50 mm, while the product size is 2 to 10 mm. This is a case of __________ crushing. (A) Primary (B) Secondary (C) Fine

Description : In a size reduction crushing operation, the feed size is 10 to 50 mm, while the product size is 2 to 10 mm. This is a case of __________ crushing. (A) Primary (B) Secondary (C) Fine

Last Answer : (C) Fine

Which of the following is not an ultrafine grinder (colloid mill)?(A) Micronizers (B) Agitated mills and fluid energy mills (C) Toothed roll crusher (D) Hammer mills with internal classification

Description : Which of the following is not an ultrafine grinder (colloid mill)? (A) Micronizers (B) Agitated mills and fluid energy mills (C) Toothed roll crusher (D) Hammer mills with internal classification

Last Answer : (C) Toothed roll crusher

To get ultrafine particles, the equipment used is a (A) Ball mill (B) Rod mill (C) Hammer crusher (D) Fluid energy mill

Description : To get ultrafine particles, the equipment used is a (A) Ball mill (B) Rod mill (C) Hammer crusher (D) Fluid energy mill

Last Answer : (D) Fluid energy mill

Fluid energy mill comes in the category of (A) Grinder (B) Crusher (C) Cutter (D) Ultrafine grinder

Description : Fluid energy mill comes in the category of (A) Grinder (B) Crusher (C) Cutter (D) Ultrafine grinder

Last Answer : (D) Ultrafine grinder

Which of the following size reduction equipments employs mainly attrition for ultrafine grinding? (A) Jet mills (B) Fluid energy mill (C) Micronizer (D) All (A), (B) and (C)

Description : Which of the following size reduction equipments employs mainly attrition for ultrafine grinding? (A) Jet mills (B) Fluid energy mill (C) Micronizer (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Crushing of mineral particles is accomplished in a 'cage mill', when one or more alloy steel bars are revolved in opposite directions. It is a type of __________ mill. (A) Impact (B) Roll (C) Vibratory (D) None of these

Description : Crushing of mineral particles is accomplished in a 'cage mill', when one or more alloy steel bars are revolved in opposite directions. It is a type of __________ mill. (A) Impact (B) Roll (C) Vibratory (D) None of these

Last Answer : (A) Impact

Stamp mills are generally used for crushing (A) Iron ores (B) Gold ores (C) Talc (D) Diamond

Description : Stamp mills are generally used for crushing (A) Iron ores (B) Gold ores (C) Talc (D) Diamond

Last Answer : (B) Gold ores

For grinding of cereals, grains, spices, pigments, saw dust, cork etc., the most extensively used size reduction equipment is a(A) Buhrstone mill(B) Ball mill(C) Crushing rolls(D) Hammer mill

Description : For grinding of cereals, grains, spices, pigments, saw dust, cork etc., the most extensively used size reduction equipment is a (A) Buhrstone mill (B) Ball mill (C) Crushing rolls (D) Hammer mill

Last Answer : (A) Buhrstone mill

A fluid energy mill is used for (A) Cutting (B) Grinding (C) Ultra-grinding (D) Crushing

Description : A fluid energy mill is used for (A) Cutting (B) Grinding (C) Ultra-grinding (D) Crushing

Last Answer : (C) Ultra-grinding

A fluid energy mill is used for (A) Cutting (B) Grinding (C) Ultra grinding (D) Crushing

Description : A fluid energy mill is used for (A) Cutting (B) Grinding (C) Ultra grinding (D) Crushing

Last Answer : (C) Ultra grinding

Size reduction of fibrous materials like wood, asbestos, mica etc. is done by a disintegrator exemplified by the(A) Blake jaw crusher(B) Cage mill(C) Stamp mill(D) Bradford's breaker

Description : Size reduction of fibrous materials like wood, asbestos, mica etc. is done by a disintegrator exemplified by the (A) Blake jaw crusher (B) Cage mill (C) Stamp mill (D) Bradford's breaker

Last Answer : (B) Cage mill

For the transportation of ultrafine particles, the equipment used is a __________ conveyor. (A) Belt (B) Pneumatic (C) Screw (D) None of these

Description : For the transportation of ultrafine particles, the equipment used is a __________ conveyor. (A) Belt (B) Pneumatic (C) Screw (D) None of these

Last Answer : (B) Pneumatic

Which of the following crushing laws is most accurately applicable to the fine grinding of materials? (A) Bond's crushing law (B) Kick's law (C) Rittinger's law (D) None of these

Description : Which of the following crushing laws is most accurately applicable to the fine grinding of materials? (A) Bond's crushing law (B) Kick's law (C) Rittinger's law (D) None of these

Last Answer : (C) Rittinger's law

Carbonisation of coal consists of  A. drying and crushing the coal to a fine powder  B. moulding the finely ground coal under pressure with or without a binding material  C. heating the wood with a limited supply of air to temperature not less than 280°C  D. none of the above

Description : Carbonisation of coal consists of  A. drying and crushing the coal to a fine powder  B. moulding the finely ground coal under pressure with or without a binding material  C. heating the wood with a limited supply of air to temperature not less than 280°C  D. none of the above

Last Answer : Answer: D

Mixing of light fine powder such as insecticides is done by (A) Banbury mixer (B) Pug mill (C) Impact wheels (D) Kneader

Description : Mixing of light fine powder such as insecticides is done by (A) Banbury mixer (B) Pug mill (C) Impact wheels (D) Kneader

Last Answer : (C) Impact wheels

In case of a ball mill, (A) Coarse feed requires a larger ball (B) Fine feed requires a larger ball (C) Operating speed should be more than the critical speed (D) None of these

Description : In case of a ball mill, (A) Coarse feed requires a larger ball (B) Fine feed requires a larger ball (C) Operating speed should be more than the critical speed (D) None of these

Last Answer : (A) Coarse feed requires a larger ball

Cement clinker is reduced to fine size by a (A) Roll crusher (B) Ball mill (C) Tube mill (D) Hammer mill

Description : Cement clinker is reduced to fine size by a (A) Roll crusher (B) Ball mill (C) Tube mill (D) Hammer mill

Last Answer : (C) Tube mill

To get a fine talc powder from its granules, the equipment used is (A) Roller crusher (B) Ball mill (C) Jaw crusher (D) Gyratory crusher

Description : To get a fine talc powder from its granules, the equipment used is (A) Roller crusher (B) Ball mill (C) Jaw crusher (D) Gyratory crusher

Last Answer : (B) Ball mill

General mechanism of size reduction in intermediate and fine grinder is by (A) Cutting action (B) Compression (C) Compression and tearing (D) Impact and attrition

Description : General mechanism of size reduction in intermediate and fine grinder is by (A) Cutting action (B) Compression (C) Compression and tearing (D) Impact and attrition

Last Answer : (D) Impact and attrition

Which of the following is used for primary crushing of very hard lumpy materials? (A) Toothed roll crusher (B) Gyratory crusher

Description : Which of the following is used for primary crushing of very hard lumpy materials? (A) Toothed roll crusher (B) Gyratory crusher

Last Answer : (B) Gyratory crusher

The main size reduction operation in ultrafine grinders is (A) Cutting (B) Attrition (C) Compression (D) Impact

Description : The main size reduction operation in ultrafine grinders is (A) Cutting (B) Attrition (C) Compression (D) Impact

Last Answer : (B) Attrition

Ultrafine grinders operate principally by (A) Slow compression (B) Impact (C) Attrition (D) Cutting action

Description : Ultrafine grinders operate principally by (A) Slow compression (B) Impact (C) Attrition (D) Cutting action

Last Answer : (C) Attrition

Temperature of the product during ultrafine grinding (A) Increases (B) Decreases (C) Remain constant (D) May increase or decrease; depends on the material being ground

Description : Temperature of the product during ultrafine grinding (A) Increases (B) Decreases (C) Remain constant (D) May increase or decrease; depends on the material being ground

Last Answer : (A) Increases

Size measurement of ultrafine particles can be best expressed in terms of (A) Centimetre (B) Screen size (C) Micron (D) Surface area per unit mass

Description : Size measurement of ultrafine particles can be best expressed in terms of (A) Centimetre (B) Screen size (C) Micron (D) Surface area per unit mass

Last Answer : (D) Surface area per unit mass

A memory in CPU that holds program instructions, input data, intermediate results and the output information produced during processing is __________ A. System B. Primary Memory C. Secondary Memory D. None of the above

Description : A memory in CPU that holds program instructions, input data, intermediate results and the output information produced during processing is __________ A. System B. Primary Memory C. Secondary Memory D. None of the above

Last Answer : B. Primary Memory

Whoever being appointed to selling postage stamp and sold excess rate a) Punishable with imprisonment for a term which may extend to 6 months/with fine which may extend to two hundred rupees, or with both; or b) Punishable with imprisonment for a term which may extend to two years, and shall also be punishable with fine c) Punishable with fine which may extend to two hundred rupees d) None of these

Description : Whoever being appointed to selling postage stamp and sold excess rate a) Punishable with imprisonment for a term which may extend to 6 months/with fine which may extend to two hundred rupees, or with ... with fine c) Punishable with fine which may extend to two hundred rupees d) None of these

Last Answer : c) Punishable with fine which may extend to two hundred rupees

A gravity decanter is meant for the separation of two __________ density. (A) Immiscible liquids of different (B) Miscible liquids of different (C) Immiscible liquids of same (D) Miscible liquids of same

Description : A gravity decanter is meant for the separation of two __________ density. (A) Immiscible liquids of different (B) Miscible liquids of different (C) Immiscible liquids of same (D) Miscible liquids of same

Last Answer : (A) Immiscible liquids of different

A 45-year-old solicitor had an onset of severe, crushing, substernal chest pain while attending a football match. He collapsed on his way to the car. Bystander Cardiorespiratory Resuscitation was begun immediately and continued until arrival in Casualty where an endotracheal tube was inserted and ventilation was maintained on 100% oxygen. Investigations revealed: pH 7.13 PaO2 560 mmHg PaCO2 18 mmHg Bicarbonate 5.8 SaO2 98% Based on these laboratory values, which of the following statements best describes his current pathophysiology? 1) He is demonstrating a primary respiratory alkalosis 2) He probably developed a large right to left intracardiac shunt 3) His anion gap is probably normal 4) His oxyhemoglobin curve is shifted to the left 5) His pulmonary artery pressure is probably elevated

Description : A 45-year-old solicitor had an onset of severe, crushing, substernal chest pain while attending a football match. He collapsed on his way to the car. Bystander Cardiorespiratory Resuscitation ... His oxyhemoglobin curve is shifted to the left 5) His pulmonary artery pressure is probably elevated

Last Answer : Answers-5 This young patient with severe central chest pain has probably arrested due to myocardial infarction and arrhythmia. His gases reveal high PO2 following 100% O2 but severe acidosis ... no left to right shunting and high pulmonary pressures would be expected after this arrest scenario.

Size reduction of the __________ can be suitably done by ball mills, crushing rolls and rod mills. (A) Metalliferous ores (B) Non-metallic ores (C) Basic slags (D) Asbestos & mica

Description : Size reduction of the __________ can be suitably done by ball mills, crushing rolls and rod mills. (A) Metalliferous ores (B) Non-metallic ores (C) Basic slags (D) Asbestos & mica

Last Answer : (A) Metalliferous ores

Crushing efficiency of a machine ranges between __________ percent. (A) 0.1 to 2 (B) 5 to 10 (C) 20 to 25

Description : Crushing efficiency of a machine ranges between __________ percent. (A) 0.1 to 2 (B) 5 to 10 (C) 20 to 25

Last Answer : (A) 0.1 to 2

General crushing equation is given by d(P/m) = -K (dD̅S /D̅ n S ). Bond's crushing law is obtained by solving this equation for n = __________ and feed of infinite size. (A) 1 (B) 1.5 (C) 2 (D) 2.5

Description : General crushing equation is given by d(P/m) = -K (dD̅S /D̅ n S ). Bond's crushing law is obtained by solving this equation for n = __________ and feed of infinite size. (A) 1 (B) 1.5 (C) 2 (D) 2.5

Last Answer : (B) 1.5

Energy consumed for crushing one ton of material ranges from __________ kWh. (A) 0.01 to 0.1 (B) 0.5 to 1.5 (C) 2 to 3.5 (D) 4 to 5

Description : Energy consumed for crushing one ton of material ranges from __________ kWh. (A) 0.01 to 0.1 (B) 0.5 to 1.5 (C) 2 to 3.5 (D) 4 to 5

Last Answer : (B) 0.5 to 1.5

Austenitic manganese steel used for making jaws of crushing machines contains about __________ percent manganese. (A) 1.5-2 (B) 3.5-4.5 (C) 7-9 (D) 12-14

Description : Austenitic manganese steel used for making jaws of crushing machines contains about __________ percent manganese. (A) 1.5-2 (B) 3.5-4.5 (C) 7-9 (D) 12-14

Last Answer : (D) 12-14

Field capacity represents the maximum quantity of water held: w) in the soil against the force of gravity x) in the ground water zone y) in the intermediate zone z) below the water table

Description : Field capacity represents the maximum quantity of water held: w) in the soil against the force of gravity x) in the ground water zone y) in the intermediate zone z) below the water table

Last Answer : ANSWER: W -- IN THE SOIL AGAINST THE FORCE OF GRAVITY

Froth floatation is used for (A) Washing fine coal dust (< 0.5 mm size) (B) Washing lump coal (> 80 mm size) (C) Removing ash from the coal based on difference in specific gravity of coal and ash

Description : Froth floatation is used for (A) Washing fine coal dust (< 0.5 mm size) (B) Washing lump coal (> 80 mm size) (C) Removing ash from the coal based on difference in specific gravity of coal and ash

Last Answer : (A) Washing fine coal dust (< 0.5 mm size)

Goods which are meant either for consumption or for investment are called - (1) Final goods (2) Giffen goods (3) Inferior goods (4) Intermediate goods

Description : Goods which are meant either for consumption or for investment are called - (1) Final goods (2) Giffen goods (3) Inferior goods (4) Intermediate goods

Last Answer : (1) Final goods Explanation: All goods which are meant either (i) for consumption by consumers or (ii) for investment by firms are called final goods. They are finished goods, meant for final ... stages of production. Cars, television sets, cloth, food, machinery, equipments etc. are final goods.

Goods which are meant either for consumption or for investment are called (1) Final goods (2) Giffen goods (3) Inferior goods (4) Intermediate goods

Description : Goods which are meant either for consumption or for investment are called (1) Final goods (2) Giffen goods (3) Inferior goods (4) Intermediate goods

Last Answer : Final goods

Run of mine (ROM) coal is crushed by a __________ for use in domestic ovens. (A) Jaw crusher (B) Hammer crusher (C) Ball mill (D) Tube mil

Description : Run of mine (ROM) coal is crushed by a __________ for use in domestic ovens. (A) Jaw crusher (B) Hammer crusher (C) Ball mill (D) Tube mil

Last Answer : (B) Hammer crusher

For achieving maximum capacity of the ball mill, the ball charge should be equal to about __________ percent of the ball mill volume. (A) 10 (B) 25 (C) 50 (D) 75

Description : For achieving maximum capacity of the ball mill, the ball charge should be equal to about __________ percent of the ball mill volume. (A) 10 (B) 25 (C) 50 (D) 75

Last Answer : (C) 50

3. __________ mill is normally used for grinding of talc. (A) Tube (B) Compartment (C) Ring-roll (D) Pebble

Description : 3. __________ mill is normally used for grinding of talc. (A) Tube (B) Compartment (C) Ring-roll (D) Pebble

Last Answer : (A) Tube

A __________ mill is a revolving mill divided into two or more sections by perforated partitions in which preliminary grinding takes place at one end and the finishing grinding at the discharge end. (A) Compartment (B) Tube (C) Rod (D) Pebble

Description : A __________ mill is a revolving mill divided into two or more sections by perforated partitions in which preliminary grinding takes place at one end and the finishing grinding at the discharge end. (A) Compartment (B) Tube (C) Rod (D) Pebble

Last Answer : (A) Compartmen

__________ mill is not used for grinding wheat into flour and for milling of cereals & other vegetable products. (A) Buhrstone (B) Roller (C) Attrition (D) Pebble

Description : __________ mill is not used for grinding wheat into flour and for milling of cereals & other vegetable products. (A) Buhrstone (B) Roller (C) Attrition (D) Pebble

Last Answer : (D) Pebble

Wet grinding in a revolving mill __________ as compared to dry grinding. (A) Gives less wear on chamber walls (B) Requires more energy (C) Increases capacity (D) Complicates handling of the product

Description : Wet grinding in a revolving mill __________ as compared to dry grinding. (A) Gives less wear on chamber walls (B) Requires more energy (C) Increases capacity (D) Complicates handling of the product

Last Answer : (C) Increases capacity

__________ balls capable of grinding the feed in a ball mill gives the maximum efficiency. (A) Cast iron (B) Minimum size (C) Maximum size (D) Elliptical

Description : __________ balls capable of grinding the feed in a ball mill gives the maximum efficiency. (A) Cast iron (B) Minimum size (C) Maximum size (D) Elliptical

Last Answer : (B) Minimum size

Size reduction of moulding powders, waxes, resins & gums are done in a __________ mill. (A) Cage (B) Hammer (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Size reduction of moulding powders, waxes, resins & gums are done in a __________ mill. (A) Cage (B) Hammer (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)