Fluid energy mill comes in the category of (A) Grinder (B) Crusher (C) Cutter (D) Ultrafine grinder

Fluid energy mill comes in the category of
(A) Grinder
(B) Crusher
(C) Cutter
(D) Ultrafine grinder
by

1 Answer

Answer :

(D) Ultrafine grinder
by

Related questions

Which of the following is not an ultrafine grinder (colloid mill)?(A) Micronizers (B) Agitated mills and fluid energy mills (C) Toothed roll crusher (D) Hammer mills with internal classification

Description : Which of the following is not an ultrafine grinder (colloid mill)? (A) Micronizers (B) Agitated mills and fluid energy mills (C) Toothed roll crusher (D) Hammer mills with internal classification

Last Answer : (C) Toothed roll crusher

To get ultrafine particles, the equipment used is a (A) Ball mill (B) Rod mill (C) Hammer crusher (D) Fluid energy mill

Description : To get ultrafine particles, the equipment used is a (A) Ball mill (B) Rod mill (C) Hammer crusher (D) Fluid energy mill

Last Answer : (D) Fluid energy mill

Which of the following size reduction equipments employs mainly attrition for ultrafine grinding? (A) Jet mills (B) Fluid energy mill (C) Micronizer (D) All (A), (B) and (C)

Description : Which of the following size reduction equipments employs mainly attrition for ultrafine grinding? (A) Jet mills (B) Fluid energy mill (C) Micronizer (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Which of the following crushers can be considered as a combination of a jaw crusher and a roller crusher? (A) Rod mill (B) Fluid energy mill (C) Gyratory crusher (D) Ball mill

Description : Which of the following crushers can be considered as a combination of a jaw crusher and a roller crusher? (A) Rod mill (B) Fluid energy mill (C) Gyratory crusher (D) Ball mill

Last Answer : (C) Gyratory crusher

Energy requirement (per unit mass of material crushed/ground) is highest for (A) Jaw crusher (B) Rod mill (C) Ball mill (D) Fluid energy mil

Description : Energy requirement (per unit mass of material crushed/ground) is highest for (A) Jaw crusher (B) Rod mill (C) Ball mill (D) Fluid energy mil

Last Answer : (D) Fluid energy mil

Arrange the following size reduction equipment in the decreasing order of the average particle size produced by each of them. (A) Jaw crusher, Ball mill, Fluid energy mill(B) Ball mill, Jaw crusher, Fluid energy mill(C) Fluid energy mill, Jaw crusher, Ball mill(D) Fluid energy mill, Ball mill, Jaw crusher

Description : Arrange the following size reduction equipment in the decreasing order of the average particle size produced by each of them. (A) Jaw crusher, Ball mill, Fluid energy mill (B) Ball mill, Jaw crusher, Fluid ... C) Fluid energy mill, Jaw crusher, Ball mill (D) Fluid energy mill, Ball mill, Jaw crusher

Last Answer : (A) Jaw crusher, Ball mill, Fluid energy mill

Feed size of ≥ 25 cms can be accepted by (A) Ball mill (B) Rod mill (C) Fluid energy mill (D) Jaw crusherFeed size of ≥ 25 cms can be accepted by(A) Ball mill(B) Rod mill(C) Fluid energy mill(D) Jaw crusher

Description : Feed size of ≥ 25 cms can be accepted by (A) Ball mill (B) Rod mill (C) Fluid energy mill (D) Jaw crusher

Last Answer : (D) Jaw crusher

Wheat is ground into flour in a (A) Hammer crusher (B) Roller crusher (C) Impact mill (D) Fluid energy mill

Description : Wheat is ground into flour in a (A) Hammer crusher (B) Roller crusher (C) Impact mill (D) Fluid energy mill

Last Answer : (B) Roller crusher

Which of the following comes in the category of primary crusher for hard and tough stone? (A) Jaw crusher (B) Cone crusher (C) Gyratory crusher (D) None of these

Description : Which of the following comes in the category of primary crusher for hard and tough stone? (A) Jaw crusher (B) Cone crusher (C) Gyratory crusher (D) None of these

Last Answer : (A) Jaw crusher

Gravity stamp mill is meant for the __________ crushing. (A) Primary (B) Intermediate (C) Fine (D) Ultrafine

Description : Gravity stamp mill is meant for the __________ crushing. (A) Primary (B) Intermediate (C) Fine (D) Ultrafine

Last Answer : (C) Fine

Run of mine (ROM) coal is crushed by a __________ for use in domestic ovens. (A) Jaw crusher (B) Hammer crusher (C) Ball mill (D) Tube mil

Description : Run of mine (ROM) coal is crushed by a __________ for use in domestic ovens. (A) Jaw crusher (B) Hammer crusher (C) Ball mill (D) Tube mil

Last Answer : (B) Hammer crusher

For the preliminary breaking of hard rock, we use a (A) Gyratory crusher(B) Ball mill(C) Tube mill(D) Squirrel-cage disintegrator

Description : For the preliminary breaking of hard rock, we use a (A) Gyratory crusher (B) Ball mill (C) Tube mill (D) Squirrel-cage disintegrator

Last Answer : (A) Gyratory crusher

Out of the following size reduction equipments, the maximum feed size can be accepted by the (A) Tube mill (B) Ball mill (C) Jaw crusher (D) Jet pulveriser

Description : Out of the following size reduction equipments, the maximum feed size can be accepted by the (A) Tube mill (B) Ball mill (C) Jaw crusher (D) Jet pulveriser

Last Answer : (C) Jaw crusher

Size reduction of fibrous materials like wood, asbestos, mica etc. is done by a disintegrator exemplified by the(A) Blake jaw crusher(B) Cage mill(C) Stamp mill(D) Bradford's breaker

Description : Size reduction of fibrous materials like wood, asbestos, mica etc. is done by a disintegrator exemplified by the (A) Blake jaw crusher (B) Cage mill (C) Stamp mill (D) Bradford's breaker

Last Answer : (B) Cage mill

Limestone is normally crushed in a (A) Roll crusher (B) Hammer crusher (C) Ball mill (D) Tube mill

Description : Limestone is normally crushed in a (A) Roll crusher (B) Hammer crusher (C) Ball mill (D) Tube mill

Last Answer : (B) Hammer crusher

Coal is finally pulverised to 200 mesh size for burning in boilers by a (A) Hammer crusher(B) Ball mill(C) Roll crusher(D) Gyratory crusher

Description : Coal is finally pulverised to 200 mesh size for burning in boilers by a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher

Last Answer : (B) Ball mill

Which of the following is a coarse crusher? (A) Smooth roll crusher (B) Toothed roll crusher (C) Gyratory crusher (D) Tube mill

Description : Which of the following is a coarse crusher? (A) Smooth roll crusher (B) Toothed roll crusher (C) Gyratory crusher (D) Tube mill

Last Answer : (C) Gyratory crusher

Fibrous material is broken by a (A) Roll-crusher (B) Squirrel-cage disintegrator (C) Ball mill (D) Tube mill

Description : Fibrous material is broken by a (A) Roll-crusher (B) Squirrel-cage disintegrator (C) Ball mill (D) Tube mill

Last Answer : (B) Squirrel-cage disintegrator

Cement clinker is reduced to fine size by a (A) Roll crusher (B) Ball mill (C) Tube mill (D) Hammer mill

Description : Cement clinker is reduced to fine size by a (A) Roll crusher (B) Ball mill (C) Tube mill (D) Hammer mill

Last Answer : (C) Tube mill

Carbon black is pulverised in a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher

Description : Carbon black is pulverised in a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher

Last Answer : (B) Ball mill

To get a fine talc powder from its granules, the equipment used is (A) Roller crusher (B) Ball mill (C) Jaw crusher (D) Gyratory crusher

Description : To get a fine talc powder from its granules, the equipment used is (A) Roller crusher (B) Ball mill (C) Jaw crusher (D) Gyratory crusher

Last Answer : (B) Ball mill

What is the real difference between a pepper mill and a salt grinder?

Description : What is the real difference between a pepper mill and a salt grinder?

Last Answer : Very little. Both take big ones and grind 'em down into smaller ones. In many cases, the internal workings are identical. If I were to be pressed to it, I would say that the main difference is that a salt grinder must be made of stainless steel, where a pepper grinder can be made of mild steel.

Draw symbol of (i) Tray Dryer (ii) Plate column (iii) Packed column (iv) Jaw crusher (v) Strirrer (vi) Ball mill.

Description : Draw symbol of (i) Tray Dryer (ii) Plate column (iii) Packed column (iv) Jaw crusher (v) Strirrer (vi) Ball mill.

Last Answer : i)Tray dryer:   ii)Plate column:    iii)Packed column:   iv) Jaw crusher:   v) Stirrer:   vi) Ball mill  

In finish machining of an island on a casting with CNC milling machine, an end mill with 10 mm diameter is employed. The corner points of the island are represented by (0, 0), (0, 30), (50, 30) and (50, 0). By applying cutter radius right compensation, the trajectory of the cutter will be a.(-5, 0), (-5, 35), (55, 35), (55,-5), (-5,-5) b.(0,-5), (55,-5), (55, 35), (-5, 35), (-5,-5) c.(5, 5), (5, 25), (45, 25), (45, 5), (5, 5) d.(5, 5), (45, 5), (45, 25), (5, 25), (5, 5)

Description : In finish machining of an island on a casting with CNC milling machine, an end mill with 10 mm diameter is employed. The corner points of the island are represented by (0, 0), (0, 30), (50, 30) and (50, 0). By applying cutter radius right ... , 5), (5, 5) d.(5, 5), (45, 5), (45, 25), (5, 25), (5, 5)

Last Answer : a.(-5, 0), (-5, 35), (55, 35), (55,-5), (-5,-5)

Explain construction and working of Cutter mill or Hammer mill

Description : Explain construction and working of Cutter mill or Hammer mill

Last Answer : CONSTRUCTION: It consists of a hopper at top and metal casing enclosing two sets of knives i.e. stationary knives attached to stator and rotating are attached to rotor. The lower part of the casing consists ... are not fixed. The mill can produce coarse to moderately fine powder DIAGRAM:  

Maximum size reduction in a fluid energy mill is achieved by (A) Compression (B) Interparticle attrition (C) Cutting (D) Impact

Description : Maximum size reduction in a fluid energy mill is achieved by (A) Compression (B) Interparticle attrition (C) Cutting (D) Impact

Last Answer : (B) Interparticle attrition

A fluid energy mill is used for (A) Cutting (B) Grinding (C) Ultra-grinding (D) Crushing

Description : A fluid energy mill is used for (A) Cutting (B) Grinding (C) Ultra-grinding (D) Crushing

Last Answer : (C) Ultra-grinding

A fluid energy mill is used for (A) Cutting (B) Grinding (C) Ultra grinding (D) Crushing

Description : A fluid energy mill is used for (A) Cutting (B) Grinding (C) Ultra grinding (D) Crushing

Last Answer : (C) Ultra grinding

Explain principle and working of fluid energy mill with a diagram.

Description : Explain principle and working of fluid energy mill with a diagram.

Last Answer : Principle  It works on the principle of impact and attrition. Working: The air or inert gas is introduced with a very high pressure through nozzles. Solids are introduced into air stream through inlet. ... 100 mesh and then passed through fluid energy mill. Diagram of fluid energy mill :

Give principle and working of “Fluid Energy mill”

Description : Give principle and working of “Fluid Energy mill”

Last Answer : Principle:  It works on the principle of combined impact and attrition. Working   1. The material which is to be size reduced is fed in the grinding chamber from the bottom through the feed ... -treated to reduce the particle size to the order of 100# and then passed through fluid energy mill

Explain working of fluid energy mill with a neat diagram.

Description : Explain working of fluid energy mill with a neat diagram.

Last Answer : Working:  1. The material which is to be size reduced is fed in the grinding chamber from the bottom through the feed inlet. 2. The air or inert gas is introduced with a very high pressure through ... particle size to the order of 100# and then passed through fluid energy mill. Diagram:   

Colloidal mills are used for __________ grinding. (A) Coarse (B) Intermediate (C) Fine (D) Ultrafine

Description : Colloidal mills are used for __________ grinding. (A) Coarse (B) Intermediate (C) Fine (D) Ultrafine

Last Answer : (D) Ultrafine

The main size reduction operation in ultrafine grinders is (A) Cutting (B) Attrition (C) Compression (D) Impact

Description : The main size reduction operation in ultrafine grinders is (A) Cutting (B) Attrition (C) Compression (D) Impact

Last Answer : (B) Attrition

Ultrafine grinders operate principally by (A) Slow compression (B) Impact (C) Attrition (D) Cutting action

Description : Ultrafine grinders operate principally by (A) Slow compression (B) Impact (C) Attrition (D) Cutting action

Last Answer : (C) Attrition

Temperature of the product during ultrafine grinding (A) Increases (B) Decreases (C) Remain constant (D) May increase or decrease; depends on the material being ground

Description : Temperature of the product during ultrafine grinding (A) Increases (B) Decreases (C) Remain constant (D) May increase or decrease; depends on the material being ground

Last Answer : (A) Increases

Use of 'grinding aids' is done in __________ grinding. (A) Dry (B) Wet (C) Ultrafine (D) Intermediate

Description : Use of 'grinding aids' is done in __________ grinding. (A) Dry (B) Wet (C) Ultrafine (D) Intermediate

Last Answer : (A) Dry

For the transportation of ultrafine particles, the equipment used is a __________ conveyor. (A) Belt (B) Pneumatic (C) Screw (D) None of these

Description : For the transportation of ultrafine particles, the equipment used is a __________ conveyor. (A) Belt (B) Pneumatic (C) Screw (D) None of these

Last Answer : (B) Pneumatic

In a size reduction crushing operation, feed size is 100 to 300 mm. while the product size is 10 to 50 mm. This is a case of the __________ crushing. (A) Primary (B) Secondary (C) Fine (D) Ultrafine

Description : In a size reduction crushing operation, feed size is 100 to 300 mm. while the product size is 10 to 50 mm. This is a case of the __________ crushing. (A) Primary (B) Secondary (C) Fine (D) Ultrafine

Last Answer : (B) Secondary

In a size reduction crushing operation, feed size is 300 to 1500 mm while the product size is 100 to 300 mm. This is a case of the __________ crushing. (A) Secondary (B) Fine (C) Primary (D) Ultrafine

Description : In a size reduction crushing operation, feed size is 300 to 1500 mm while the product size is 100 to 300 mm. This is a case of the __________ crushing. (A) Secondary (B) Fine (C) Primary (D) Ultrafine

Last Answer : (C) Primary

Size measurement of ultrafine particles can be best expressed in terms of (A) Centimetre (B) Screen size (C) Micron (D) Surface area per unit mass

Description : Size measurement of ultrafine particles can be best expressed in terms of (A) Centimetre (B) Screen size (C) Micron (D) Surface area per unit mass

Last Answer : (D) Surface area per unit mass

Energy consumption in a crusher decreases with increase in the (A) Size of the product (at constant feed size) (B) Capacity of the crushing machine (C) Size of feed (at constant reduction ratio) (D) All (A), (B) & (C)

Description : Energy consumption in a crusher decreases with increase in the (A) Size of the product (at constant feed size) (B) Capacity of the crushing machine (C) Size of feed (at constant reduction ratio) (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

During size reduction by a jaw crusher, the energy consumed decreases with the (A) Decreasing size of product at constant size of feed (B) Decreasing machine capacity (C) Increasing size of feed at constant reduction ratio (D) None of these

Description : During size reduction by a jaw crusher, the energy consumed decreases with the (A) Decreasing size of product at constant size of feed (B) Decreasing machine capacity (C) Increasing size of feed at constant reduction ratio (D) None of these

Last Answer : (C) Increasing size of feed at constant reduction ratio

Mechanical conveyors which push the material along an endless trough or tube are called scrappers. Which of the following conveying equipments comes under the category of ‘scrappers’? (A) Bucket conveyor (B) Flight conveyor (C) Screw conveyor (D) Both (B) and (C)

Description : Mechanical conveyors which push the material along an endless trough or tube are called scrappers. Which of the following conveying equipments comes under the category of ‘scrappers’? (A) Bucket conveyor (B) Flight conveyor (C) Screw conveyor (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

What energy change take place in grinder mixer?

Description : What energy change take place in grinder mixer?

Last Answer : electricity to potential energy

Pick out the wrong statement. (A) Recycled coarse material to the grinder by a classifier is termed as circulating load (B) Wear and tear in wet crushing is more than that in dry crushing of materials (C) Size enlargement (opposite of size reduction) is not a mechanical operation (D) A 'dust catcher' is simply an enlargement in a pipeline which permits the solids to settle down due to reduction in velocity of the dust laden gas

Description : Pick out the wrong statement. (A) Recycled coarse material to the grinder by a classifier is termed as circulating load (B) Wear and tear in wet crushing is more than that in dry crushing of ... a pipeline which permits the solids to settle down due to reduction in velocity of the dust laden gas

Last Answer : (C) Size enlargement (opposite of size reduction) is not a mechanical operation

General mechanism of size reduction in intermediate and fine grinder is by (A) Cutting action (B) Compression (C) Compression and tearing (D) Impact and attrition

Description : General mechanism of size reduction in intermediate and fine grinder is by (A) Cutting action (B) Compression (C) Compression and tearing (D) Impact and attrition

Last Answer : (D) Impact and attrition

What comes under the category of second-class mail. -SST 10th

Description : What comes under the category of second-class mail. -SST 10th

Last Answer : Book packets, registered newspapers and periodicals come under the category of second-class mail.

Are janotra community comes under general category?

Description : Are janotra community comes under general category?

Last Answer : Need answer

Which among the following Writs comes into the category of public litigation petition before High Court or Supreme Court? (1) a challenge to elections of the office-bearers of a political party (2) against political interference (3) against the decision of Lower Court (4) against a general topic

Description : Which among the following Writs comes into the category of public litigation petition before High Court or Supreme Court? (1) a challenge to elections of the office-bearers of a political party (2) against political interference (3) against the decision of Lower Court (4) against a general topic

Last Answer : (4) against a general topic Explanation: Although the proceedings in the Supreme Court arise out of the judgments or orders made by the Subordinate Courts including the High Courts, but of ... India only and perhaps no other Court in the world has been exercising this extraordinary jurisdiction.

Which of the following comes under the category of Development Banks? A. Industrial Development Banks B. Agricultural Development Banks C. Housing Development Banks D. Export-Import Development Banks E. All of the Above

Description : Which of the following comes under the category of Development Banks? A. Industrial Development Banks B. Agricultural Development Banks C. Housing Development Banks D. Export-Import Development Banks E. All of the Above

Last Answer : E. All of the Above Explanation: