It is a protocol used to connect the other packet witching network A. X.25 B. X.50 C. X.10 D. X.75

It is a protocol used to connect the other packet witching network
A. X.25
B. X.50
C. X.10
D. X.75
by

1 Answer

Answer :

D. X.75
by

Related questions

What is the typical gain of a rhombic antenna? A. Between 15 to 60 B. Between 20 to 90 C. Between 50 to 75 D. Between 10 to 25

Description : What is the typical gain of a rhombic antenna? A. Between 15 to 60 B. Between 20 to 90 C. Between 50 to 75 D. Between 10 to 25

Last Answer : A. Between 15 to 60

What is the characteristic impedance of a single wire with a diameter d= 0.25 mm placed at the center between grounded parallel planes separated by 1 mm apart. The wire is held by a material with a velocity factor of 0.75. A. 85 Ω B. 63 Ω C. 50 Ω D. 75 Ω

Description : What is the characteristic impedance of a single wire with a diameter d= 0.25 mm placed at the center between grounded parallel planes separated by 1 mm apart. The wire is held by a material with a velocity factor of 0.75. A. 85 Ω B. 63 Ω C. 50 Ω D. 75 Ω

Last Answer : D. 75 Ω

What is the impedance of a balance 4-wire with a diameter of 0.25 cm and spaced 2.5 cm apart using an insulator with a dielectric constant of 2.56? A. 100Ω B. 65Ω C. 75 Ω D. 50 Ω

Description : What is the impedance of a balance 4-wire with a diameter of 0.25 cm and spaced 2.5 cm apart using an insulator with a dielectric constant of 2.56? A. 100Ω B. 65Ω C. 75 Ω D. 50 Ω

Last Answer : A. 100Ω

The ________is a network layer Internet protocol that provides message packets to report errors and other information regarding IP packet processing back to the source: a) Internet Control Message Protocol b) Internet Standard Flexible Message Protocol c) Internet Dynamic Chartered Message Protocol d) None of These

Description : The ________is a network layer Internet protocol that provides message packets to report errors and other information regarding IP packet processing back to the source: a) Internet Control Message ... Standard Flexible Message Protocol c) Internet Dynamic Chartered Message Protocol d) None of These

Last Answer : a) Internet Control Message Protocol

Determine from the following the basic mode of transmission system in the public data network in which data are transferred from the source to the network and from the network to the destination in the frame format. A. Voice mode B. Asynchronous mode C. Synchronous mode D. Packet mode

Description : Determine from the following the basic mode of transmission system in the public data network in which data are transferred from the source to the network and from the network to the destination in the frame format. A. Voice mode B. Asynchronous mode C. Synchronous mode D. Packet mode

Last Answer : D. Packet mode

Which of the following assertions is FALSE about the Internet Protocol (IP)? a. It is possible for a computer to have multiple IP addresses b. IP packets from the same source to the same destination can take different routes in the network c. IP ensures that a packet is discarded if it is unable to reach its destination within a given number of hops d. The packet source cannot set the route of an outgoing packets; the route is determined only by the routing tables in the routers on the way

Description : Which of the following assertions is FALSE about the Internet Protocol (IP)? a. It is possible for a computer to have multiple IP addresses b. IP packets from the same source to the same ... outgoing packets; the route is determined only by the routing tables in the routers on the way

Last Answer : d. The packet source cannot set the route of an outgoing packets; the route is determined only by the routing tables in the routers on the way

Network layer at source is responsible for creating a packet from data coming from another ________ a) Station b) Link c) Node d) Protocol

Description : Network layer at source is responsible for creating a packet from data coming from another ________ a) Station b) Link c) Node d) Protocol

Last Answer : d) Protocol

7.How does traceroute work? A. It uses an ICMP destination-unreachable message to elicit the name of a router. B. It sends a specially crafted IP packet to a router to locate the number of hops from the sender to the destination network. C. It uses a protocol that will be rejected by the gateway to determine the location. D. It uses the TTL value in an ICMP message to determine the number of hops from the sender to the router.

Description : 7.How does traceroute work? A. It uses an ICMP destination-unreachable message to elicit the name of a router. B. It sends a specially crafted IP packet to a router to locate the number of hops from ... the TTL value in an ICMP message to determine the number of hops from the sender to the router.

Last Answer : D. It uses the TTL value in an ICMP message to determine the number of hops from the sender to the router.

Four bits are used for packet sequence numbering in a sliding window protocol used in computer network...

Description : Four bits are used for packet sequence numbering in a sliding window protocol used in computer network. What is maximum window size?  A) 4 B) 8 C) 15 D) 16

Last Answer : Four bits are used for packet sequence numbering in a sliding window protocol used in computer network. What is maximum window size?  15

What is the velocity factor for non-foam dielectric 50 or 75 ohm flexible coaxial cable such as RG 8, 11, 58 and 59? A. 2.70 B. 0.66 C. 0.30 D. 0.10

Description : What is the velocity factor for non-foam dielectric 50 or 75 ohm flexible coaxial cable such as RG 8, 11, 58 and 59? A. 2.70 B. 0.66 C. 0.30 D. 0.10

Last Answer : B. 0.66

What is the velocity factor for non-foam dielectric 50 or 75 ohm flexible coaxial cable such as RG 8, 11, 58 and 59? A. 2.70 B. 0.10 C. 0.66 D. 0.30

Description : What is the velocity factor for non-foam dielectric 50 or 75 ohm flexible coaxial cable such as RG 8, 11, 58 and 59? A. 2.70 B. 0.10 C. 0.66 D. 0.30

Last Answer : C. 0.66

Which command is used to test network connectivity and provide a response to each packet received by the remote host? a.test b.tracer c.ping d.connect

Description : Which command is used to test network connectivity and provide a response to each packet received by the remote host? a.test b.tracer c.ping d.connect

Last Answer : c.ping

What is the market's historical performance on a quadruple witching day?

Description : What is the market's historical performance on a quadruple witching day?

Last Answer : I don’t know the answer. Have you consulted an experienced broker?

What is the main point of Hamlet's soliloquy Now is the very witching time of night...?

Description : What is the main point of Hamlet's soliloquy Now is the very witching time of night...?

Last Answer : No, it's not to tell us that he's a vampire, even though he says he could drink hot blood. Mostly it's to tell us what he has in mind for his upcoming visit to his ... beginning he expresses his bloodthirsty (figuratively, not literally) mood but he is less bloodthirsty as the soliloquy progresses.

ECE Board Exam March 1996 Modems are required to connect computer to telephone lines because ___________. A. telephone company rules required them B. the telephone network bandwidth is too high C. none of the above D. the telephone network will pass direct current

Description : ECE Board Exam March 1996 Modems are required to connect computer to telephone lines because ___________. A. telephone company rules required them B. the telephone network bandwidth is too high C. none of the above D. the telephone network will pass direct current

Last Answer : D. the telephone network will pass direct current

Cellular radios use FM with a maximum deviation of A. ±30 khz B. ±75 khz C. ±25 khz D. ±12 khz

Description : Cellular radios use FM with a maximum deviation of A. ±30 khz B. ±75 khz C. ±25 khz D. ±12 khz

Last Answer : D. ±12 khz

The allowable deviation ratio of commercial FM broadcast. A. 25 B. 15 C. 5 D. 75

Description : The allowable deviation ratio of commercial FM broadcast. A. 25 B. 15 C. 5 D. 75

Last Answer : C. 5

The numerical aperture of a fiber if the angle of acceptance is 15 degrees, is a. 017 b. 0.26 c. 0.50 d. 0.75

Description : The numerical aperture of a fiber if the angle of acceptance is 15 degrees, is a. 017 b. 0.26 c. 0.50 d. 0.75

Last Answer : b. 0.26

What is the lifetime of ILDs? a. 50,000 hours b. 75,000 hours c. 100,000 hours d. 125,000 hours

Description : What is the lifetime of ILDs? a. 50,000 hours b. 75,000 hours c. 100,000 hours d. 125,000 hours

Last Answer : a. 50,000 hours

What is transit time (time delay) of a 50-ft length transmission line of the above problem? A. 50 ns B. 100 ns C. 75 ns D. 65 ns

Description : What is transit time (time delay) of a 50-ft length transmission line of the above problem? A. 50 ns B. 100 ns C. 75 ns D. 65 ns

Last Answer : C. 75 ns

Which of the following is not common transmission line impedance? A. 50 ohms B. 120 ohms C. 75 ohms D. 650 ohms

Description : Which of the following is not common transmission line impedance? A. 50 ohms B. 120 ohms C. 75 ohms D. 650 ohms

Last Answer : B. 120 ohms

When adjusting an RF filter on a transmitter using a dummy load, how much watts dissipation should it stand to test a 150 watts transmitter? A. 75 watts B. 300 watts C. 50 watts D. 150 watts

Description : When adjusting an RF filter on a transmitter using a dummy load, how much watts dissipation should it stand to test a 150 watts transmitter? A. 75 watts B. 300 watts C. 50 watts D. 150 watts

Last Answer : D. 150 watts

What is the data link protocol that is used in asynchronous transmission for transferring files from one computer to another? A. A modem B. X modem C. B modem D. C modem

Description : What is the data link protocol that is used in asynchronous transmission for transferring files from one computer to another? A. A modem B. X modem C. B modem D. C modem

Last Answer : B. X modem

What is the data link protocol that is used in asynchronous transmission for transferring files from one computer to another? A. A modem B. X modem C. B modem

Description : What is the data link protocol that is used in asynchronous transmission for transferring files from one computer to another? A. A modem B. X modem C. B modem

Last Answer : B. X modem

Which protocols adopted the standards of HDLC (High Level Link Control) protocol? a. X.25 protocol as LAPB (Link Access Procedure Balanced, V.42 protocol as LAPM (Link Access Procedure for Modems) b. Frame Relay protocol as LAPF (Link Access Procedure for Frame Relay) c. ISDN (Integrated Services Digital Network) protocol as LAPD (Link Access Procedure on D channel) d. All the above

Description : Which protocols adopted the standards of HDLC (High Level Link Control) protocol? a. X.25 protocol as LAPB (Link Access Procedure Balanced, V.42 protocol as LAPM (Link Access Procedure for ... Services Digital Network) protocol as LAPD (Link Access Procedure on D channel) d. All the above

Last Answer : d. All the above

A flywheel rotating at 5 revolutions per second is brought to rest by a constant torque in 10 seconds. How many revolutions does the flywheel make while coming to a stop? w) 25 x) 50 y) 75 z) 100

Description : A flywheel rotating at 5 revolutions per second is brought to rest by a constant torque in 10 seconds. How many revolutions does the flywheel make while coming to a stop? w) 25 x) 50 y) 75 z) 100

Last Answer : ANSWER: W -- 25

The IP packet that carries an IGMP packet has a value of _______ in its protocol field. A) 3 B) 2 C) 1 D) noneof the above

Description : The IP packet that carries an IGMP packet has a value of _______ in its protocol field. A) 3 B) 2 C) 1 D) noneof the above

Last Answer : 2

For which one of the following reasons does Internet Protocol (IP) use the time-to- live (TTL) field in the IP datagram header? a. Ensure packets reach destination within that time b. Discard packets that reach later than that time c. Prevent packets from looping indefinitely d. Limit the time for which a packet gets queued in intermediate routers.

Description : For which one of the following reasons does Internet Protocol (IP) use the time-to- live (TTL) field in the IP datagram header? a. Ensure packets reach destination within that time b. ... packets from looping indefinitely d. Limit the time for which a packet gets queued in intermediate routers.

Last Answer : c. Prevent packets from looping indefinitely

Consider a link with packet loss probability of 0.2. What is the expected number of transmissions it would take to transfer 200 packets given that the stop and wait protocol is used? a. 125 b. 250 c. 225

Description : Consider a link with packet loss probability of 0.2. What is the expected number of transmissions it would take to transfer 200 packets given that the stop and wait protocol is used? a. 125 b. 250 c. 225

Last Answer : b. 250

When does the station B send a positive acknowledgement (ACK) to station A in Stop and Wait protocol? a. only when no error occurs at the transmission level b. when retransmission of old packet in a novel frame is necessary c. only when station B receives frame with errorsd. all of the above

Description : When does the station B send a positive acknowledgement (ACK) to station A in Stop and Wait protocol? a. only when no error occurs at the transmission level b. when retransmission of old packet in a novel frame is necessary c. only when station B receives frame with errors d. all of the above

Last Answer : only when no error occurs at the transmission level

When does the station B send a positive acknowledgement (ACK) to station A in Stop and Wait protocol? a. only when no error occurs at the transmission level b. when retransmission of old packet in a novel frame is necessary c. only when station B receives frame with errors d. all of the above

Description : When does the station B send a positive acknowledgement (ACK) to station A in Stop and Wait protocol? a. only when no error occurs at the transmission level b. when retransmission of old packet in a novel frame is necessary c. only when station B receives frame with errors d. all of the above

Last Answer : only when no error occurs at the transmission level

State weather the following statement is true or false for IPV6 Addressing 1). IPV6 is a routable protocol that addresses, routes, fragments, and reassembles packets 2).IPV6 is a connectionless, unreliable datagram protocol. 3). An IPV6 packet consists of an IPV6 header and an IPV6 payload. A. 1. True, 2. true, 3. true B. 1. true, 2. false, 3. false C. 1. false, 2. false, 3. false D. 1.false, 2. true, 3. true

Description : State weather the following statement is true or false for IPV6 Addressing 1). IPV6 is a routable protocol that addresses, routes, fragments, and reassembles packets 2).IPV6 is a connectionless, unreliable datagram protocol. 3). ... C. 1. false, 2. false, 3. false D. 1.false, 2. true, 3. true

Last Answer : A. 1. True, 2. true, 3. true

Two of the protocols that can be carried in the Protocol field of an IP packet are? * TCP * UDP * FTP * TFTP

Description : Two of the protocols that can be carried in the Protocol field of an IP packet are? * TCP * UDP * FTP * TFTP

Last Answer : Correct answer: A & B The following are the fields in an IP segment, their length, and their definitions: VERS (Version number - 16 bits) HLEN (Number of 32-bit words in the header - 4 bits) Type ... (32 bits) IP Options (network testing, debugging, security and others - 4 bits) Data (4 bits).

Transmission protocol, PRMA stands for _________ a) Pocket reservation multiple access b) Packet register multiple access c) Pocket register multiple access d) Packet reservation multiple access

Description : Transmission protocol, PRMA stands for _________ a) Pocket reservation multiple access b) Packet register multiple access c) Pocket register multiple access d) Packet reservation multiple access

Last Answer : d) Packet reservation multiple access

You are measuring noise at a +3 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -57dBm. This is ________dBa0. A. 20 B. 15 C. 25 D. 17

Description : You are measuring noise at a +3 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -57dBm. This is ________dBa0. A. 20 B. 15 C. 25 D. 17

Last Answer : C. 25

A reading of -50 dBm on the disturbing pair, and -80 on the disturbed pair equals _____ dB of crosstalk coupling. A. 20 B. 30 C. 60 D. 25

Description : A reading of -50 dBm on the disturbing pair, and -80 on the disturbed pair equals _____ dB of crosstalk coupling. A. 20 B. 30 C. 60 D. 25

Last Answer : B. 30

If a transmission line has a power loss of 6 dB per 100 feet, what is the power at the feed point to the antenna at the end of a 200 foot transmission line fed by a 100 watt transmitter? A. 70 watts B. 50 watts C. 25 watts D. 6 watts

Description : If a transmission line has a power loss of 6 dB per 100 feet, what is the power at the feed point to the antenna at the end of a 200 foot transmission line fed by a 100 watt transmitter? A. 70 watts B. 50 watts C. 25 watts D. 6 watts

Last Answer : D. 6 watts

At 100% modulation, the sum fo the effective voltages in both sidebands is equal to ______% of the unmodulated carrier voltage. A. 50 B. 71 C. 100 D. 25

Description : At 100% modulation, the sum fo the effective voltages in both sidebands is equal to ______% of the unmodulated carrier voltage. A. 50 B. 71 C. 100 D. 25

Last Answer : B. 71

What is the effective radiated power of a repeater with 75 watts transmitter power output, 4 dB feedline loss, 3 dB duplexer and circulator loss, and 10 dB antenna gain? A. 600 W B. 75 W C. 18.75 W D. 150 W

Description : What is the effective radiated power of a repeater with 75 watts transmitter power output, 4 dB feedline loss, 3 dB duplexer and circulator loss, and 10 dB antenna gain? A. 600 W B. 75 W C. 18.75 W D. 150 W

Last Answer : D. 150 W

A device that connects two dissimilar networks and performs the protocol conversion. A. Gateway B. Coupler C. Transformer D. Converter

Description : A device that connects two dissimilar networks and performs the protocol conversion. A. Gateway B. Coupler C. Transformer D. Converter

Last Answer : A. Gateway

Rules governing the transmission of digital information. A. Line protocol B. Isochronous C. Data communications D. Digital communications

Description : Rules governing the transmission of digital information. A. Line protocol B. Isochronous C. Data communications D. Digital communications

Last Answer : B. Isochronous

Asynchronous protocol is A. message oriented B. clock oriented C. bit oriented D. character oriented

Description : Asynchronous protocol is A. message oriented B. clock oriented C. bit oriented D. character oriented

Last Answer : D. character oriented

ECE Board Exam March 1996 What is the IBM’s asynchronous data link protocol designation? A. 83 B B. 8A1 / 8B1 C. 93 B D. 9A1/ 9B1

Description : ECE Board Exam March 1996 What is the IBM’s asynchronous data link protocol designation? A. 83 B B. 8A1 / 8B1 C. 93 B D. 9A1/ 9B1

Last Answer : A. 83 B

The total amount of iodine in the body of an average adult is (A) 10–15 mg (B) 20–25 mg (C) 45–50 mg (D) 75–100 mg MINERAL METABOLISM 199

Description : The total amount of iodine in the body of an average adult is (A) 10–15 mg (B) 20–25 mg (C) 45–50 mg (D) 75–100 mg MINERAL METABOLISM 199

Last Answer : Answer : C

The adequate daily dietary requirement of molybdenum for normal human adult is (A) 10–20 µg (B) 25–50 µg (C) 50–70 µg (D) 75–200 µg

Description : The adequate daily dietary requirement of molybdenum for normal human adult is (A) 10–20 µg (B) 25–50 µg (C) 50–70 µg (D) 75–200 µg

Last Answer : Answer : D

The molecular weight of light chains is (A) 10,000–15,000 (B) 20,000–25,000 (C) 25,000–50,000 (D) 50,000–75,000

Description : The molecular weight of light chains is (A) 10,000–15,000 (B) 20,000–25,000 (C) 25,000–50,000 (D) 50,000–75,000

Last Answer : Answer : B

For achieving maximum capacity of the ball mill, the ball charge should be equal to about __________ percent of the ball mill volume. (A) 10 (B) 25 (C) 50 (D) 75

Description : For achieving maximum capacity of the ball mill, the ball charge should be equal to about __________ percent of the ball mill volume. (A) 10 (B) 25 (C) 50 (D) 75

Last Answer : (C) 50

Yield of charcoal in high temperature carbonisation of wood is about __________ percent. (A) 10 (B) 25 (C) 50 (D) 75

Description : Yield of charcoal in high temperature carbonisation of wood is about __________ percent. (A) 10 (B) 25 (C) 50 (D) 75

Last Answer : (B) 25

High relative humidity decreases the evaporative process and as the temperature is increased, the relative humidity decreases. The comfort range for human body is the ambient temperature of 22 to 27°C with relative humidity ranging from __________ percent. (A) 5 to 10 (B) 15 to 25 (C) 45 to 50 (D) 75 to 80

Description : High relative humidity decreases the evaporative process and as the temperature is increased, the relative humidity decreases. The comfort range for human body is the ambient temperature of 22 to 27°C with relative humidity ranging from __________ ... to 10 (B) 15 to 25 (C) 45 to 50 (D) 75 to 80

Last Answer : (C) 45 to 50