In some engines glycerine is used in place of water for cooling of engine. Why ?

In some engines glycerine is used in place of water for cooling of engine. Why ?
by

1 Answer

Answer :

Glycerine has boiling point of 90°C which increases its heat carrying capacity. Thus weight of coolant gets reduced and smaller radiator can be used.
by

Related questions

Glycerine is used as a coolant in cooling of some engines instead of water, because (A) Its higher boiling point (290°C) increases its heat carrying capacity (B) Comparatively less weight of coolant is required (C) Smaller radiator can be used (D) All a, b & c

Description : Glycerine is used as a coolant in cooling of some engines instead of water, because (A) Its higher boiling point (290°C) increases its heat carrying capacity (B) Comparatively less weight of coolant is required (C) Smaller radiator can be used (D) All a, b & c

Last Answer : (D) All a, b & c

Scavenging air in diesel engine means a. air used for combustion under pressure b. forced air for cooling the cylinder c. burnt air containing products of combustion d. air used for forcing burnt gases out of the engines cylinder during the exhaust stroke

Description : Scavenging air in diesel engine means a. air used for combustion under pressure b. forced air for cooling the cylinder c. burnt air containing products of combustion d. air used for forcing burnt gases out of the engines cylinder during the exhaust stroke

Last Answer : ANSWER d. air used for forcing burnt gases out of the engines cylinder during the exhaust stroke

Which of the following engines was introduced by a German engineer, Nickolas Otto?  a. Gasoline engine  b. Diesel engine  c. Gas turbine  d. Thermal engine

Description : Which of the following engines was introduced by a German engineer, Nickolas Otto?  a. Gasoline engine  b. Diesel engine  c. Gas turbine  d. Thermal engine

Last Answer : Gasoline engine

Which of the following engines is the most efficient?  a. Gas turbine  b. Diesel engine  c. Carnot engine  d. Gasoline engine

Description : Which of the following engines is the most efficient?  a. Gas turbine  b. Diesel engine  c. Carnot engine  d. Gasoline engine

Last Answer : Carnot engine

Which of the following best describes both Stirling and Ericson engines?  a. Internal combustion engine  b. External combustion engine  c. Diesel cycle  d. Rankine cycle

Description : Which of the following best describes both Stirling and Ericson engines?  a. Internal combustion engine  b. External combustion engine  c. Diesel cycle  d. Rankine cycle

Last Answer : External combustion engine

What states that thermal efficiencies of all reversible heat engines operating between the same two reservoirs are the same and that no heat engine is more efficient than a reversible one operating between the same two reservoirs?  A. Ericson principle  B. Carnot principle  C. Otto principle  D. Stirling principle

Description : What states that thermal efficiencies of all reversible heat engines operating between the same two reservoirs are the same and that no heat engine is more efficient than a reversible one operating between the ... A. Ericson principle  B. Carnot principle  C. Otto principle  D. Stirling principle

Last Answer : Carnot principle

Two identical weights are dropped simultaneously, one on water and the other in glycerine. Which of the following statement is correct? a.The weight will settle slowly in water but quickly in glycerine b.The weights will take same time to settle c.The water level will fall but glycerine level will rise d.The weight will settle quickly in water but slowly in glycerine e.107 dynes

Description : Two identical weights are dropped simultaneously, one on water and the other in glycerine. Which of the following statement is correct? a.The weight will settle slowly in water but quickly in glycerine ... level will rise d.The weight will settle quickly in water but slowly in glycerine e.107 dynes

Last Answer : d. The weight will settle quickly in water but slowly in glycerine

What is the function of thermostat in cooling system of an engine ?

Description : What is the function of thermostat in cooling system of an engine ?

Last Answer : Thermostat ensures optimum cooling because excessive cooling decreases the overall efficiency. It allows cooling water to go to radiator beyond a predetermined temperature.

In SI engines knocking can be reduced by (a) Increasing the compression ratio (b) Increasing the cooling water temperature (c) Retarding the spark advance (d) Increasing the inlet air temperature

Description : In SI engines knocking can be reduced by (a) Increasing the compression ratio (b) Increasing the cooling water temperature (c) Retarding the spark advance (d) Increasing the inlet air temperature

Last Answer : Ans :c

The effect that takes place which results in cooling action is1. Condensing 2. Heating 3. Cooling 4. Evaporating

Description : The effect that takes place which results in cooling action is1. Condensing 2. Heating 3. Cooling 4. Evaporating

Last Answer : Evaporating

Which are the reference fuels for knock rating of S.I. engines ?

Description : Which are the reference fuels for knock rating of S.I. engines ?

Last Answer : n-heptane and ISO-octane.

Why thermal efficiency of I.C. engines is more than that of gas turbine plant ?

Description : Why thermal efficiency of I.C. engines is more than that of gas turbine plant ?

Last Answer : In I.C. engine maximum temperature attained is higher than in gas turbine.

Why iso-octane is chosen as reference fuel for S.I. engines and allotted 100 value for its octane number ?

Description : Why iso-octane is chosen as reference fuel for S.I. engines and allotted 100 value for its octane number ?

Last Answer : Iso-octane permits highest compression without causing knocking.

Why iso-octane is chosen as reference fuel for S.I. engines and allotted 100 value for its octane number ?

Description : Why iso-octane is chosen as reference fuel for S.I. engines and allotted 100 value for its octane number ?

Last Answer : Iso-octane permits highest compression without causing knocking

Horse power of I.C. engines can be expressed as RAC rating, SAE rating, or DIN rating. To which countries these standards belong ?

Description : Horse power of I.C. engines can be expressed as RAC rating, SAE rating, or DIN rating. To which countries these standards belong ?

Last Answer : U.K., USA and Germany respectively.

Why efficiency of gas turbines is lower compared to I.C. engines ?

Description : Why efficiency of gas turbines is lower compared to I.C. engines ?

Last Answer : In gas turbines, 70% of the output of gas turbine is consumed by compressor. I.C. engines have much lower auxiliary consumption. Further combustion temperature of I.C. engines is much higher compared to gas turbine.

Production of tractors, motor, engines and process equipment is domain of organised a) Unorganised sector b) Organised sector c) Both of the above d) None of above

Description : Production of tractors, motor, engines and process equipment is domain of organised a) Unorganised sector b) rOrganised sector c) Both of the above d) None of above

Last Answer : Organised sector

The production of irrigation pumps and diesel engines started during……. a)1950s b)1930s c)1940s d)2000s

Description : The production of irrigation pumps and diesel engines started during……. a)1950s b)1930s c)1940s d)2000s

Last Answer : 1930S

Which of the following engines is the most efficient?  a. Isobaric expansion  b. Adiabatic compression  c. Adiabatic expansion  d. Isothermal expansion

Description : Which of the following engines is the most efficient?  a. Isobaric expansion  b. Adiabatic compression  c. Adiabatic expansion  d. Isothermal expansion

Last Answer : Isobaric expansion

Gasoline and Diesel Engines are best described by the _________.  a. Otto Cycle  b. Burnign Cycle  c. Shikki Cycle  d. Shapa R’ Elli Cycle

Description : Gasoline and Diesel Engines are best described by the _________.  a. Otto Cycle  b. Burnign Cycle  c. Shikki Cycle  d. Shapa R’ Elli Cycle

Last Answer : Otto Cycle

The compression ratio for Diesel engines is  A. 3 to 6  B. 5 to 8  C. 15 to 20  D. 20 to 30

Description : The compression ratio for Diesel engines is  A. 3 to 6  B. 5 to 8  C. 15 to 20  D. 20 to 30

Last Answer : Answer: C

Which is the incorrect statement about Carnot cycle?  A. It is used as the alternate standard of comparison of all heat engines.  B. All the heat engines are based on Carnot cycle.  C. It provides concept of maximising work output between the two temperature limits.  D. all of the above

Description : Which is the incorrect statement about Carnot cycle?  A. It is used as the alternate standard of comparison of all heat engines.  B. All the heat engines are based on Carnot cycle.  C. It provides concept of maximising work output between the two temperature limits.  D. all of the above

Last Answer : Answer: B

The compression ratio for petrol engines is  A.3 to 6  B.5 to 8  C.15 to 20  D.20 to 30

Description : The compression ratio for petrol engines is  A.3 to 6  B.5 to 8  C.15 to 20  D.20 to 30

Last Answer : Answer: B

Zeroth law of thermodynamics  (a) deals with conversion of mass and energy  (b) deals with reversibility and irreversibility of process  (c) states that if two systems are both in equilibrium with a third system, they are in thermal equilibrium with each other  (d) deals with heat engines  (e) does not exist.

Description : Zeroth law of thermodynamics  (a) deals with conversion of mass and energy  (b) deals with reversibility and irreversibility of process  (c) states that if two systems are both in equilibrium with a ... in thermal equilibrium with each other  (d) deals with heat engines  (e) does not exist.

Last Answer : Answer : c

I have 1997 Subaru Legacy Outback. If the timing belt breaks, will it destroy the engine? I've heard some engines will be destroyed, while others will not.

Description : I have 1997 Subaru Legacy Outback. If the timing belt breaks, will it destroy the engine? I've heard some engines will be destroyed, while others will not.

Last Answer : It may break possibly causing serious engine damage. When a timing belt breaks, the camshaft stops turning leaving some of the valves in the open position. The crankshaft, because it's heavier, ... done or engine getting destroyed and needing a new engine half way through your trip . good luck

Why don't expert automobile mechanics design engines or are mechanical engineers that design engines by nature expert engine mechanics?

Description : Why don't expert automobile mechanics design engines or are mechanical engineers that design engines by nature expert engine mechanics?

Last Answer : You need to know physics to tee to design an engine. I know how to take apart my PC and reassemble it and do trouble shooting, but I have no idea how to design a processor or board pathway layouts.

Which of the following statements about search engine is true? (a) Search engines discriminate between good and bad sites. -Technology

Description : Which of the following statements about search engine is true? (a) Search engines discriminate between good and bad sites. -Technology

Last Answer : (d) Search engine is a program designed to search for information on the Web using keywords.

Morse test is conducted on the engine to calculate the mechanical efficiency of A. single cylinder CI engine B. single cylinder SI engine C. only on two stroke engines D. multi cylinder engine

Description : Morse test is conducted on the engine to calculate the mechanical efficiency of A. single cylinder CI engine B. single cylinder SI engine C. only on two stroke engines D. multi cylinder engine

Last Answer : ANSWER : D

The knocking in spark ignition engines can be reduced by a. Retarding the spark. b. Increasing the engine speed. c. Both a and b d. None of these.

Description : The knocking in spark ignition engines can be reduced by a. Retarding the spark. b. Increasing the engine speed. c. Both a and b d. None of these.

Last Answer : ANSWER c. Both a and b.

The knocking in spark ignition engines can be reduced by a. Retarding the spark. b. Increasing the engine speed. c. Both a and b. d. None of these.

Description : The knocking in spark ignition engines can be reduced by a. Retarding the spark. b. Increasing the engine speed. c. Both a and b. d. None of these.

Last Answer : ANSWER c. Both a and b

For the same capacity engines, the compression ratio of diesel engine a. is lower than the compression ratio of SI engine b. is higher than the compression ratio of SI engine c. is same as the compression ratio of SI engine d. cannot say

Description : For the same capacity engines, the compression ratio of diesel engine a. is lower than the compression ratio of SI engine b. is higher than the compression ratio of SI engine c. is same as the compression ratio of SI engine d. cannot say

Last Answer : ANSWER b. is higher than the compression ratio of SI engine

In the pitch control diagram shown in the illustration, what are the present plant operating conditions? EL-0095 A. One engine is on the line, cruise mode is selected and the engine room is in control. B. One engine is on the line, maneuvering mode is selected and the bridge is in control. C. Both engines are on line, cruise mode is selected and the bridge is in control. D. Both engines are on line, maneuvering mode is selected and the engine room is in control.

Description : In the pitch control diagram shown in the illustration, what are the present plant operating conditions? EL-0095 A. One engine is on the line, cruise mode is selected and the engine room is in control. ... . D. Both engines are on line, maneuvering mode is selected and the engine room is in control.

Last Answer : Answer: D

. If a website’s search engines get saturated with respect to a particular search engine by 20%, what is it exactly? A. 20% of the web pages of the website have been indexed by the search engine B. 20% of the website’s pages will never be indexed C. Only 20% of the pages of the website will be indexed by the search engine D. The website ranks in the first 20% of all websites indexed by the search engine for its most important search terms

Description : . If a website's search engines get saturated with respect to a particular search engine by 20%, what is it exactly? A. 20% of the web pages of the website have been indexed by the search ... ranks in the first 20% of all websites indexed by the search engine for its most important search terms

Last Answer : A. 20% of the web pages of the website have been indexed by the search engine

. A Hallway Page is used to: A. Attract visitors straight onto the Hallway Page from the search engines B. Organizes the Doorway Pages C. Guides people navigate to different Doorway Pages D. Enables search engine bots to index the Doorway Pages

Description : . A Hallway Page is used to: A. Attract visitors straight onto the Hallway Page from the search engines B. Organizes the Doorway Pages C. Guides people navigate to different Doorway Pages D. Enables search engine bots to index the Doorway Pages

Last Answer : D. Enables search engine bots to index the Doorway Pages

Google advertising program is:  A. online platform for advertising through google search engine  B.online platform for monitoring organic reach  C.online platform for creating ads for all search engines  D.None of the above

Description : Google advertising program is:  A. online platform for advertising through google search engine  B.online platform for monitoring organic reach  C.online platform for creating ads for all search engines  D.None of the above

Last Answer : A. online platform for advertising through google search engine

Which Has More Efficiency: Diesel Engine Or Petrol Engines?

Description : Which Has More Efficiency: Diesel Engine Or Petrol Engines?

Last Answer : Off course Diesel engine has the better efficiency out of two.

Twenty years ago, a plane is flying at 20,000 feet over Germany. If you will recall, Germany at the time was politically divided into West Germany and East Germany. Anyway, during the flight, TWO of the engines fail. The pilot, realizing that the last remaining engine is also failing, decides on a crash landing procedure. Unfortunately the engine fails before he has time and the plane crashes smack in the middle of "no man's land" between East Germany and West Germany. Where would you bury the survivors - East Germany or West Germany or in "no man's land"?

Description : Twenty years ago, a plane is flying at 20,000 feet over Germany. If you will recall, Germany at the time was politically divided into West Germany and East Germany. Anyway, during the flight, TWO of the ... . Where would you bury the survivors - East Germany or West Germany or in "no man's land"?

Last Answer : Answer: You don't, of course, bury survivors. If you said, "Don't bury the survivors" then proceed to the next question.

Which statement best describes the operating principle of a constant-speed propeller? a. As throttle setting is changed by the pilot, the prop governor causes pitch angle of the propeller blades to remain unchanged b. The propeller control regulates the engine RPM and in turn the propeller RPM c. A high blade angle, or increased pitch, reduces the propeller drag and allows more engine power for take-offs d. As the propeller control setting is changed by the pilot, the RPM of the engines remains constant as the pitch angle of the propeller changes

Description : Which statement best describes the operating principle of a constant-speed propeller? a. As throttle setting is changed by the pilot, the prop governor causes pitch angle of the propeller blades to ... the pilot, the RPM of the engines remains constant as the pitch angle of the propeller changes

Last Answer : b. The propeller control regulates the engine RPM and in turn the propeller RPM

List the various fuels used in I.C. engines. Write the properties of Biodiesel Fuels used in I. C. engine.

Description : List the various fuels used in I.C. engines. Write the properties of Biodiesel Fuels used in I. C. engine.

Last Answer : 1 Petrol 2. Diesel 3. LPG 4. CNG 5.Hydrogen 6.Alcohol 7.Bio diesel Properties biodiesel  i) It is a renewable substitute fuel for petroleum diesel. ii) It has lower exhaust ... diesel vi) It is an environmentally friendly fuel that an be used in any diesel engine without modification.

Differentiate air fuel ratio between carburetted engine and electronic fuel injection engines control system.

Description : Differentiate air fuel ratio between carburetted engine and electronic fuel injection engines control system.

Last Answer : Sr. No. Carburetted engine Electronic Fuel Injection (EFI) engine 1 Fuel atomization depends upon velocity of air in the venturi. Atomization of fuel is independent of cranking ... occurs in carbureted engine. Equal quantity of fuel is supplied to port for each cylinder

White phosphorus is generally kept under – (1) Alcohol (2) Water (3) Glycerine (4) Kerosene oil

Description : White phosphorus is generally kept under – (1) Alcohol (2) Water (3) Glycerine (4) Kerosene oil

Last Answer : (2) Water Explanation: White phosphorous is kept under water because it reacts with oxygen but not water. Besides, it is insoluble in water. It presents a significant fire hazard due to its extreme reactivity with atmospheric oxygen.

Speed of sound is the greatest in : (1) Water (2) Air (3) Glass (4) Glycerine

Description : Speed of sound is the greatest in : (1) Water (2) Air (3) Glass (4) Glycerine

Last Answer : (3) Glass Explanation: Sound travels faster in liquids and non-porous solids than it does in air. It travels about 4.3 times as fast in water (1,484 m/s), and nearly 15 times as fast in iron (5,120 m/s), than in air at 20 degrees Celsius.

Explain the effect of increasing the temperature of a liquid, on intermolecular forces operating between its particles. What will happen to the viscosity of a liquid if its temperature is increased? Arrange the following in increasing order of viscosity-water, hexane, glycerine.

Description : Explain the effect of increasing the temperature of a liquid, on intermolecular forces operating between its particles. What will happen to the viscosity of a liquid if its temperature is increased? Arrange the following in increasing order of viscosity-water, hexane, glycerine.

Last Answer : Ans. On increasing the temperature , the kinetic energy of liquid molecules increases so that it can overcome the attractive forces between the molecules and hence liquid can flow more easily i.e. viscosity decreases. Order of increasing viscosity : hexane < water < glycerine.

White phosphorus is generally kept under (1) Alcohol (2) Water (3) Glycerine (4) Kerosene oil

Description : White phosphorus is generally kept under (1) Alcohol (2) Water (3) Glycerine (4) Kerosene oil

Last Answer : Water

Speed of sound is the greatest in : (1) Water (2) Air (3) Glass (4) Glycerine

Description : Speed of sound is the greatest in : (1) Water (2) Air (3) Glass (4) Glycerine

Last Answer : Glass

What willl happen if density of ball bearing is less than density of glycerine oil?

Description : What willl happen if density of ball bearing is less than density of glycerine oil?

Last Answer : What is the answer ?

Which of these is produced by a mould? (1) Chloroform (2) Glycerine (3) Penicillin (4) Quinine

Description : Which of these is produced by a mould? (1) Chloroform (2) Glycerine (3) Penicillin (4) Quinine

Last Answer : (3) Penicillin Explanation: Penicillin is one of the first and still one of the most widely used antibiotic agents - derived from the Penicillium mold. Penicillin kills bacteria by interfering with the ability to synthesize cell wall.

Which one of the following is used as preservative for foodstuff? (1) Sodium Benzoate (2) Picric acid (3) Glycerine (4) Sodium Chloride

Description : Which one of the following is used as preservative for foodstuff? (1) Sodium Benzoate (2) Picric acid (3) Glycerine (4) Sodium Chloride

Last Answer : (1) Sodium Benzoate Explanation: Sodium benzoate is a preservative. It is bacteriostatic and fungistatic under acidic conditions. It is most widely used in acidic foods such as salad dressings (vinegar), ... (vinegar), and condiments. It is also used as a preservative in medicines and cosmetics.

Soap is prepared by boiling caustic soda with – (1) Alcohol (2) Kerosene oil (3) Glycerine (4) Fats

Description : Soap is prepared by boiling caustic soda with – (1) Alcohol (2) Kerosene oil (3) Glycerine (4) Fats

Last Answer : (4) Fats Explanation: The most basic kind of soap is made from cuastic soda and animal fat. The two are heated together, and then cooled. The process is called "saponification". In technical ... hydrolysis of triglyeerides which are esters of fatty acids, to form the sodium salt, of a carboxylate.