Description : The method of determination of indicated power of multi cylinder SI engine is by use of (a) Morse test (b) Prony brake test (c) Motoring test (d) Heat balance test
Last Answer : Ans : a
Description : A two stroke engine has a speed of 750 rpm. A four stroke engine having an identical cylinder size runs at 1500 rpm. The theoretical output of the two stroke engine will (a) Be twice that of the four stroke ... ) Be the same as that of the four stoke (d) Depend upon whether it is a CI or SI engine
Last Answer : Ans :c
Description : In a morse test for a 2 cylinder, 2 S SI engine, the brake power was 9 kW. Whereas the brake power of individual cylinders with spark cut off were 4.25 kW and 3.75 kW. The mecheffic of the engine is (a) 90% (b) 80% (c) 45.5% (d) 52.5%
Last Answer : Ans :a
Description : For same power output and same r, as compared to 2- stroke engines, four stroke SI engines have (a) Higher fuel consumption (b) Lower thermal efficiency (c) Highest exhaust temperatures (d) Higher thermal efficiency
Last Answer : Ans :d
Description : Scavenging air in diesel engine means a. air used for combustion under pressure b. forced air for cooling the cylinder c. burnt air containing products of combustion d. air used for forcing burnt gases out of the engines cylinder during the exhaust stroke
Last Answer : ANSWER d. air used for forcing burnt gases out of the engines cylinder during the exhaust stroke
Description : Ignition timing of a multi-cylinder SI engine can be adjusted by A. rotating the cam shaft B. adjusting the generator pulley C. rotating the distributor D. adjusting the pump pulley
Last Answer : ANSWER : C
Description : In _____________ injection system only one pump is sufficient for multi-cylinder engine. a) air b) mechanical c) compression fuel d) common rail
Last Answer : Answer: d Explanation: None.
Description : Explain the procedure of Morse Test” to be conducted for four cylinder petrol engine.
Last Answer : Morse Test: Used for multi cylinder engines Procedure: 1. The engine is run at the required speed and the torque is measured. 2. One cylinder is cut out by shorting the plug if an S.I. engine is under test. 3. ... -B4 Total IP of Engine = I1+I2+I3+I4 Friction Power F.P. = I.P - B.P
Description : In compression ignition (CI) engine, the compression ratio is a. Cylinder volume / Clearance volume b. Swept Volume / Cylinder Volume c. Clearance volume / Cylinder volume d. Cylinder volume / Swept volume (Ans:a)
Last Answer : In two stroke engine there is one power stroke in _____ of crankshaft rotation. a. 90° b. 180° c. 270° d. 360° (Ans:d)
Description : For the same capacity engines, the compression ratio of diesel engine a. is lower than the compression ratio of SI engine b. is higher than the compression ratio of SI engine c. is same as the compression ratio of SI engine d. cannot say
Last Answer : ANSWER b. is higher than the compression ratio of SI engine
Description : An engine working on air standard Otto cycle has a cylinder diameter of 10 cm and stroke length of 15 cm. The ratio of specific heats for air is 1.4. If the clearance volume is 196.3 cc and the heat supplied per kg of air per ... kg of air is a. 879.1 kJ/ b. 890.2 kJ c. 895.3 kJ d. 973.5 kJ
Last Answer : ANSWER d. 973.5 kJ
Description : Motoring test is conducted on IC engines to determine A. brake power B. indicated power C. friction power D. fuel consumption at full load
Description : Alcohols alone cannot be used in CI engines as a) their self ignition temperature is high b) latent heat of vaporization is high c) all of the mentioned d) none of the mentioned
Last Answer : Answer: c Explanation: None.
Description : The knocking tendency in CI engines increases with (a) Increase of coolant water temperature (b) Increase of temperature of inlet air (c) Decrease of compression ratio (d) Increase of compression ratio
Description : Which of the following factors increases the tendency of knocking in the CI engines? (a) Increasing both the r and coolant temperatures (b) Increasing both the speed and the injection advance (c) Increasing the speed, injection advance and coolant temperature (d) Increasing the compression ratio
Description : In four stroke engine which of the following is also known as power stroke a. Suction stroke b. Compression stroke c. Expansion stroke d. Exhaust stroke (Ans:c) Measurements of fuel and air ... into IC engine,___________its efficiency A. increase B. decrease C. does not alter D. unpredictable on
Last Answer : ANSWER : B
Description : A gas engine has a volume of 300 cc and clearance volume of 25 cc. Its volumetric efficiency is 0.8 and mech efficiency is 0.9. What is the volume of the mixture taken in per stroke? (a) 248 cc (b) 252 cc (c) 264 cc (d) 286 cc
Last Answer : Ans : c
Description : The term scavenging is generally associated with a. 2-stroke engine b. 4-stroke engine c. high efficiency engine d. diesel engine
Last Answer : ANSWER C. high efficiency engine
Description : In a variable speed SI engine, the maximum torque occurs at the maximum (a) Speed (b) Brake power (c) Indicated power (d) Volumetric efficiency
Description : How the efficiency of the SI engine is affected by the specific heat ratio (γ) of the working fluid? a. the efficiency of the engine increases with increase in specific heat ratio (γ) of the working ... not affected by change in specific heat ratio (γ) of the working fluid d. none of the above
Last Answer : ANSWER a. the efficiency of the engine increases with increase in specific heat ratio (γ) of the working fluid
Description : Solid injection in CI engine means injection of A. solid fuel only B. liquid fuel only C. liquid fuel and air D. solid fuel and air
Description : If the performance of diesel engine of different sizes, cylinder dimensions and power rating are to be compared, which of the following parameters can be used for such comparison? (a) Swept volume (b) Air fuel ratio (c) Specific brake fuel consumption (d) Volumetric efficiency
Description : A 40 kW engine has a mechanical efficiency of 80 %. If the frictional power is assumed to be constant with load, what is the approximate value of the mechanical efficiency at 50 % of the rated load? (a) 45% (b) 55 % (c) 65% (d) 75%
Description : Ratio of actual indicated work to hypothetical indicated work in a steam engine is the (a) Indicated thermal efficiency (b) Friction factor (c) Mechanical efficiency (d) Diagram factor
Last Answer : Ans : d
Description : The ratio of indicated power to shaft power of the engine required to drive the compressor is called A. Compressor efficiency B. Volumetric efficiency C. Isothermal efficiency D. Mechanical efficiency
Last Answer : ANSWER : D
Description : In SI engines knocking can be reduced by (a) Increasing the compression ratio (b) Increasing the cooling water temperature (c) Retarding the spark advance (d) Increasing the inlet air temperature
Description : The tendency of knocking in CI engine reduces by (a) High self ignition temperature of fuel (b) Decrease in jacket water temperature (c) Injection of fuel just before TDC (d) Decrease in injection pressure
Description : Fuel is injected into the cylinder at the end of ______________ stroke. a) suction b) compression c) expansion d) exhaust
Last Answer : Answer: b Explanation: Fuel is injected into the cylinder at the end of compression stroke and not at suction or expansion stroke.
Description : With EFI of diesel engines a) sharp start and stop is not possible b) very high injection pressure can be obtained c) sudden cylinder cut-off is impossible d) diagnostic properties are poor
Last Answer : Answer: b Explanation: Generally, with EFI of diesel engines very high injection pressure can be obtained.
Description : In compression ignition engines, swirl denotes a. Haphazard motion of the gases in the cylinder b. Rotary motion of the gases in the cylinder. c. Radial motion of the gases in the cylinder. d. None of the above
Last Answer : ANSWER a. Haphazard motion of the gases in the chamber
Description : Compare performance characteristics of SI and CI engines.
Last Answer : Variable/Parameter SI Engine CI Engine Power output per unit weight 2.7 Kg/Kw 6.5 Kg/Kw Power output per unit displacement 30 Kw/liter 15 Kw/liter Acceleration Not ... load, idling. Fuel safety More volatile so less safer Less volatile so more safer
Description : In multi stage compressor, the isothermal compression is achieved by A. Employing intercooler B. By constantly cooling the cylinder C. By running compressor at very slow speed D. By insulating the cylinder
Description : The ratio of work done per cycle to the stroke volume of the compressor is known as A. Compressor capacity B. Compression ratio C. Compressor efficiency D. Mean effective pressure
Description : In two stroke engine one power occurs in _______ of crank rotation A. 180° B. 360° C. 270° D. 720°
Description : In two stroke engine, which of the following functions are performed at the same time? a. Compression and exhaust b. Intake and Expansion c. Intake and exhaust d. Intake and compression (Ans:c)
Last Answer : The compression ratio in a Compression Ignition (CI) engine is generally in between a. 8 to 13 b. 14 to 23 c. 20 to 28 d. 25 to 32 (Ans:b)
Description : For low load operation more economical engine is a. petrol engine b. diesel engine c. muticylinder engine d. two stroke engine
Last Answer : ANSWER b. diesel engine
Description : Which of the following engine can work on very lean mixture a. Spark ignition engine b. compression ignition engine c. two stroke engine d. Four stroke engine
Last Answer : ANSWER b. compression ignition engine
Description : The actual volume of fresh charge admitted in 4-stroke petrol engine is A. equal to stroke volume B. equal stroke volume and clearance volume C. less than stroke volume D. more than stroke volume
Description : In a typical medium speed 4- stroke Diesel engine, the inlet valve A. opens 20°before top dead centre and closes at 35°afterthebottomdead centre. B. opens up at top dead centre and closes at bottomdead centre C. may open orcloseanywhere D. remains open for 200°
Last Answer : ANSWER : A
Description : In four stroke engine there is one power stroke in _____ of crankshaft rotation. a. 180° b. 360° c. 540° d. 720° (Ans:d)
Last Answer : The ascending order of strokes in four stroke engine is a. Suction stroke - Expansion stroke - Compression stroke - Exhaust stroke b. Suction stroke - Compression stroke - Expansion stroke -Exhaust ... stroke d. Suction stroke - Compression stroke - Exhaust stroke - Expansion stroke (Ans:b)
Description : The knocking in spark ignition engines can be reduced by a. Retarding the spark. b. Increasing the engine speed. c. Both a and b d. None of these.
Last Answer : ANSWER c. Both a and b.
Description : The knocking in spark ignition engines can be reduced by a. Retarding the spark. b. Increasing the engine speed. c. Both a and b. d. None of these.
Last Answer : ANSWER c. Both a and b
Description : The accumulation of carbon in a cylinder results in increase of A. clearance volume B. volumetric efficiency C. ignition time D. effective compression ratio
Description : The accumulation of carbon in a cylinder results in increase of a. clearance volume b. volumetric efficiency c. ignition time d. effective compression ratio
Last Answer : ANSWER d. effective compression ratio
Description : The compression ratio in a Spark Ignition (SI) engine is generally in between a. 7 to 10 b. 10 to 14 c. 14 to 18 d. 18 to 22 (Ans:a)
Last Answer : Which of the following is not true for two stroke engine as compared to four stroke engine? a. Less cooling is required b. Greater lubrication is required c. More uniform torque on crankshaft d. Complete exhaust of products of combustion (Ans:a)
Description : Velocity of flame propagation in SI engine is maximum for a fuel air mixture which is (a) 10% richer than stoichiometric (b) Equal to stoichiometric (c) More than 10% richer than stoichiometric (d) 10% leaner than stoichiometric
Description : In a SI engine, which one of the following is the correct order of the fuels with increasing detonation tendency? (a) Paraffins, olefins, naphthenes, aromatics (b) Aromatics, naphthenes, paraffins, olefins (c) Naphthenes, olefins, aromatics, paraffins (d) Aromatics, naphthenes, olefins, paraffins
Description : Reference fuels for knock rating of SI engine fuels would include (a) Iso octane alpha methyl naphthalene (b) Normal octance and aniline (c) Isooctance and n octane (d) N heptane and iso octane
Description : In a single acting reciprocating compressor, the suction, compression and delivery of air takes place in A. One stroke B. Two stroke C. Three stroke D. Four stroke
Description : The advantage of dry compression is that (a) it permits higher speeds to be used (b) it permits complete evaporation in the evaporator (c) it results in high volumetirc and mechanical efficiency (d) all of the above
Last Answer : Ans: d