Draw a neat labelled diagram of 1-2 shell and tube heat exchanger.

Draw a neat labelled diagram of 1-2 shell and tube heat exchanger. 
by

1 Answer

Answer :

1-2 shell and tube heat exchanger: 

image

by

Related questions

Name any four types of shell and tube heat exchanger.

Description : Name any four types of shell and tube heat exchanger.

Last Answer : Four types of shell and tube heat exchanger: 1. Fixed tube heat exchanger 2. Floating head heat exchanger 3. U- tube type heat exchanger 4. Kettle/ Reboiler type heat exchanger

With neat sketch explain the construction and working of heat exchanger used for handling corrosive liquid.

Description : With neat sketch explain the construction and working of heat exchanger used for handling corrosive liquid.

Last Answer : Graphite block heat exchanger:   Graphite heat exchangers are well suited for handling corrosive fluids. Graphite is inert towards most corrosive fluids and has very high thermal conductivity. Graphite being ... vertical faces direct the service fluid through the exchanger in a cross flow.

Explain with reason through which side of shell and tube heat exchanges, the following liquids are directed. (i) viscous liquid (ii) high pressure liquid (iii) corrosive liquid

Description : Explain with reason through which side of shell and tube heat exchanges, the following liquids are directed. (i) viscous liquid (ii) high pressure liquid (iii) corrosive liquid

Last Answer : Viscous liquid : Viscous liquid is passed through shell side Reason: because of the presence of baffles in the shell induce turbulence and hence increases heat transfer rate. High pressure liquid: High ... To avoid expensive alloy shells (in order to save the cost of expensive material for shell).

With a neat diagram explain the construction of calendria type evaporator.

Description : With a neat diagram explain the construction of calendria type evaporator.

Last Answer : Calendria type(Short tube) evaporator: Construction: It consists of vertical cylindrical shell incorporating short vertical tube bundle with horizontal tube sheet. Vapour inlet is provided at top ... sheet, while non condensable gas is vented to atmosphere from point near top tube sheet.

Calculate the rate of heat transfer by radiation from an unlagged steam pipe, 50 mm o.d. at 393K to air at 293K emissivity e = 0.9.

Description : Calculate the rate of heat transfer by radiation from an unlagged steam pipe, 50 mm o.d. at 393K to air at 293K emissivity e = 0.9.

Last Answer : Rate of heat transfer by radiation Assume length of pipe = 1 m

Give the unit of overall heat transfer coefficient in SI and MKS.

Description : Give the unit of overall heat transfer coefficient in SI and MKS.

Last Answer : Unit of overall heat transfer coefficient 1. In SI : W/m2K 2. In MKS : kcal/hr m2K

Define film heat transfer coefficient.

Description : Define film heat transfer coefficient.

Last Answer : Film heat transfer coefficient: Film heat transfer coefficient h is defined as the quantity of heat transferred in unit time through unit area at a temperature difference of 10 between the surface and surrounding.

Define steady state heat transfer.

Description : Define steady state heat transfer.

Last Answer : Steady state heat transfer: Heat transfer where temperature remains same with respect to time and the rate of heat transfer does not vary with time.

Explain the type of multiple effect evaporator feed arrangement used for handling viscous liquid.

Description : Explain the type of multiple effect evaporator feed arrangement used for handling viscous liquid.

Last Answer : Backward feed arrangement  If the liquid is very viscous, then we have to adopt backward feed arrangement. In this arrangement, the feed solution and vapour flow is in opposite direction. Fresh feed is ... Not very common as it need pump. At low values of feed temperature higher economy.

Explain Wilson plot.

Description : Explain Wilson plot.

Last Answer : Wilson Plot: The Wilson plot method was developed by Wilson in 1915 to evaluate the convection coefficients in shell and tube condensers for the case of a vapour condensing outside by means of ... resistance and the remaining thermal resistances participating in the heat transfer process.

Explain Kirchhoff’s Law with its mathematical expression in detail.

Description : Explain Kirchhoff’s Law with its mathematical expression in detail.

Last Answer : Kirchoff's law of radiation: Kirchoff's law: It states that at equilibrium temperature, the ratio of total emissive power of any body to absorptivity depends only upon the temperature of the body. ... respectively. At thermal equilibrium, absorption and emission rates are equal, thus,

Define the following terms : (i) absorptivity (ii) reflectivity (iii) transmissivity (iv) emissivity

Description : Define the following terms : (i) absorptivity (ii) reflectivity (iii) transmissivity (iv) emissivity

Last Answer : Absorptivity: It is the fraction of total incident radiation which is absorbed by a body. Reflectivity: It is the fraction of total incident radiation which is reflected by a body.  Transmissivity: It ... total emissive power of a body to emissive power of a black body at the same temperature. 

Explain the properties of solution that influences evaporation.

Description : Explain the properties of solution that influences evaporation.

Last Answer : Properties of evaporating liquid 1. Concentration: As the concentration increases, the solution becomes more and more individualistic. The viscosity and density increase with solid content. The boiling point of ... is a problem, special materials such as copper, nickel, stainless steel may be used.

Explain the concept of optimum thickness of insulation.

Description : Explain the concept of optimum thickness of insulation.

Last Answer : Optimum thickness of insulation: The optimum thickness of an insulation is obtained by purely economic approach. The greater the thickness, the lower the heat loss & the greater the initial cost of ... sum values of heat lost and annual fixed charges) of the insulation is minimum. 

Give expression for the following and explain the terms involved. (i) Nusselt number (ii) Prandtl number

Description : Give expression for the following and explain the terms involved. (i) Nusselt number (ii) Prandtl number

Last Answer : 1. Nusselt NumberNNU= hd/k  h – fim heat transfer coefficient  d - diameter of pipe  k – thermal conductivity of fluid 2. Prandtl Number NPR -Cp µ/k Cp– specific heat of fluid µ - viscosity of fluid  k – thermal conductivity

Define capacity and economy of evaporator.

Description : Define capacity and economy of evaporator.

Last Answer : The capacity of an evaporator is defined as the number of kilogram of water evaporated per hour. The economy of an evaporator is defined as the number of kilogram of water evaporated per kilogram of steam fed to the evaporator.

Define radiation and give one example.

Description : Define radiation and give one example.

Last Answer : Radiation: Radiation is transfer of energy through space by electromagnetic waves. If radiation is passing through empty space, it is not transformed into other forms of energy, nor is it diverted from its ... only the absorbed energy that appears as heat. Example: Loss of heat from unlagged pipe. 

Heat Transfer Software

Description : Heat Transfer Software

Last Answer : The process of heat transfer is used in many industries - the scientific industry, engineering industry and every industry you can possibly think of that uses thermal heat. Because of this, there is a need ... group, so you won't have to go through the hassle of copying information down for others.

Heat Transfer Machines

Description : Heat Transfer Machines

Last Answer : Heat transfer machines are just the thing you need in order to do heat transfers on your clothing or whatever surface you want to decorate. In order for you to stick designs and precious stones on porous and ... is best. This will also give you an idea of what kind of designs you can choose from.

Heat Transfer Experiments

Description : Heat Transfer Experiments

Last Answer : Heat transfer experiments are basically experiments that deal with temperature, its characteristics and qualities. Heat transfer experiments are done for many purposes, but mainly to do investigations on the ... three are learned, it helps to have a better understanding of heat transfers as well.

Explain the operation of UPS with a neat block diagram.

Description : Explain the operation of UPS with a neat block diagram.

Last Answer : Uninterruptible-Power-Supplies (UPS): A block diagram of UPS system is shown in figure. It essentially consists of four major components: i)Rectifier (or battery charger) ii) ... . Due to fast action requirement, transfer switch can be implemented by fast acting semiconductor devices.

Draw diagram of class A push-pull amplifier and explain its operation.

Description : Draw diagram of class A push-pull amplifier and explain its operation. 

Last Answer : Class A Push-pull Amplifier: The circuit diagram of class A push-pull amplifier is as shown in the fig.(a). Operation: The resistors R1 and R2 along with Vcc provide the dc biasing so as ... Vcc is applied to the collectors of transistors Q1 and Q2 through the centretapped output transformer. 

Draw neat and labeled sketch of three pass packages type boiler.

Description : Draw neat and labeled sketch of three pass packages type boiler. 

Last Answer : Each set of tubes that hot combustion flue gas travels through before making a turn within the boiler, is considered a "pass." A 3-pass fire tube boiler design consists of three sets of ... design that allows more heat transfer time to deliver the same or higher efficiency rating. 

With neat sketch explain four modes of operation of a TRIAC?

Description : With neat sketch explain four modes of operation of a TRIAC? 

Last Answer : Modes of operation of a TRIAC: There are four different operating modes of TRIAC:  1) MT2 and gate are positive with respect to terminal MT1(Mode1) : Here terminal MT2 is positive ... junction P2-N2 is forward biased, current carriers are injected and therefore, the TRIAC is turned on. 

Draw P-V and T-S diagram for isochoric process.

Description : Draw P-V and T-S diagram for isochoric process.

Last Answer : Isochoric Process: 

Draw P-V and T-S diagram of dual combustion cycle.

Description : Draw P-V and T-S diagram of dual combustion cycle.

Last Answer : Dual combustion cycle: 1-2 Isentropic compression of air 2-3 the combustion of fuel at constant volume. 3-4 the combustion of fuel at constant pressure 4-5 Isentropic expansion during which work is done by the system. 5-1 Heat rejection at constant volume.

Draw P-V and T-S diagram for brayton cycle.

Description : Draw P-V and T-S diagram for brayton cycle.

Last Answer : P-V and T-S diagram for brayton cycle.

Draw & explain operation of phase detector.

Description : Draw & explain operation of phase detector.

Last Answer : In phase detector, the op-Amp basically acts as a zero crossing detector. If a sine wave is applied at the i/p, we get square wave at the op-Amp o/p (at point ... to two channel of the CRO. The time duration between the pulses corresponding to voltages represent the phase between them. 

Draw and explain integrated duration curve used in system operation.

Description : Draw and explain integrated duration curve used in system operation. 

Last Answer : Diagram of integrated duration curve used in system operation: Explanation:  Integrated duration curve is obtained from load duration curve. It is drawn in between load on Y-axis in KW/MW and the X- ... a particular time of a day can also be shown on a curve which is called as mass curve. 

What is photodiode? Draw the symbol and explain operation of photodiode.

Description : What is photodiode? Draw the symbol and explain operation of photodiode. 

Last Answer : A photodiode is a light detector that converts light into an electrical current. A photodiode is a semi-conductor device, with a p-n junction and an intrinsic layer between p and n layers ... current is independent of reverse bias voltage. Reverse current is mostly depends on the light intensity.

What is PLL? Explain its operation with a block diagram.

Description : What is PLL? Explain its operation with a block diagram.

Last Answer : PLL - A phase-locked loop or phase lock loop is a control system that generates an output signal whose phase is related to the phase of an input signal Block diagram  ... to the input frequency. The phase - locked loop goes through three states free running capture and phase lock.

operation of DSO with block diagram.

Description : operation of DSO with block diagram.

Last Answer : The input is amplified and attenuated with input amplifiers. The output of the input signal amplifiers feeds an analog to digital converter (ADC). There are numbers of ADC available. But the selection of ADC ... view the display on the CRT, the data from memory is reconstructed in analog form.

Describe principle of operation of Doppler type ultrasonic flow meter with diagram.

Description : Describe principle of operation of Doppler type ultrasonic flow meter with diagram. 

Last Answer : Diagram: Working:  The flow meter consists of a crystal transducer mounted outside the pipe in which flow is to be measured. This transducer is a piezoelectric crystal which ... , so the frequency of the reflected wave is shifted to particle velocity, according to Doppler principle.

Describe the operation of N channel enhancement type MOSFET with diagram.

Description : Describe the operation of N channel enhancement type MOSFET with diagram.

Last Answer : As its name indicates, this MOSFET operates only in the enhancement mode and has no depletion mode. It operates with large positive gate voltage only. It does not conduct when the ... of charge carriers attracted to the positive gate. Thus drain current is controlled by the gate potential.

Explain two pass down flow surface condenser with a neat sketch.

Description : Explain two pass down flow surface condenser with a neat sketch.

Last Answer : Two pass down flow surface condenser: It consists of horizontal cast iron cylindrical vessel pack with tubes, through which the cooling water flows. The ends of the condenser are cut off by vertical ... convert into water; therefore whole condensate can be the reused in the boiler. 

Draw a neat and labelled diagram of Ascaris.

Description : Draw a neat and labelled diagram of Ascaris.

Last Answer : Draw a neat and labelled diagram of Ascaris.

Draw a neat and labelled diagram:  1. Cnidoblast 2. Colloblast

Description : Draw a neat and labelled diagram:  1. Cnidoblast 2. Colloblast

Last Answer : Draw a neat and labelled diagram: 1. Cnidoblast 2. Colloblast

Draw a neat labelled diagram showing steam distillation at laboratory scale

Description : Draw a neat labelled diagram showing steam distillation at laboratory scale

Last Answer : labelled diagram showing steam distillation at laboratory scale

Draw neat labelled constructional diagram of INKJET printer. Describe the function of each block. State two advantages.

Description : Draw neat labelled constructional diagram of INKJET printer. Describe the function of each block. State two advantages.

Last Answer : It is a non-impact printer. It provides letter quality printout than dot matrix printer. Its output is sharper than Dot matrix though its output quality is not to the same level of laser printer ... is compatible in quality to that of a laser printer. Faster when compared to Dot Matrix printers.

Draw a neat labelled block diagram of AC electric locomotive. State the function of each part.

Description : Draw a neat labelled block diagram of AC electric locomotive. State the function of each part.

Last Answer : labelled diagram ofAC electric locomotive:  Function of AC electric locomotive Parts: 1) Overhead contact wire: Supply of 1-ph, 25KV, 50Hz, AC is given to overhead conductor. 2) Current collecting ... mechanical power to run the train i.e. DC series motor which is used as traction motor.

Draw a neat labelled diagram of photocell and state two properties of photons.

Description : Draw a neat labelled diagram of photocell and state two properties of photons.  

Last Answer : Properties of Photon: 1) Photon is electrically neutral. 2) Photon travels with speed of light. 3) Photon do not ionized. 4) Photon has rest mass zero. 5) Photon cannot be deflected by electric or magnetic ... has momentum term h / λ 7) Photon has definite packets of energy given by E = hʋ

Draw a neat labelled diagram of feeding post and write any four points related to it.

Description : Draw a neat labelled diagram of feeding post and write any four points related to it.

Last Answer : Feeding post: 1) Each feeder has two conductors one insulated for 25 kV (connected to bus-bar) and other for 3 kV (connected to track for return current). 2) Located as near as ... are supposed to operate only under normal current as they are not provided with protection for the same. 

Draw a neat labelled diagram of PLC. Explain the function of each block.

Description : Draw a neat labelled diagram of PLC. Explain the function of each block.

Last Answer : Block Diagram of PLC:-  A simplified block diagram of a PLC shown in above Fig. It has three major units/sections.  I/O (Input/Output) Modules.  CPU (Central ... membrane keypad for program entry, and a display device (LED or LCD) for viewing program steps of functions. 

Condensing film co-efficient for steam on horizontal tubes ranges from 5000 to 15000 Kcal/hr.m2 .°C. Condensation of vapor is carried out inside the tube in a shell and tube heat exchanger, when the (A) Higher condensing film co-efficient is desired (B) Condensate is corrosive in nature (C) Lower pressure drop through the exchanger is desired (D) Temperature of the incoming vapor is very high Answer: Option B

Description : Condensing film co-efficient for steam on horizontal tubes ranges from 5000 to 15000 Kcal/hr.m2 .°C. Condensation of vapor is carried out inside the tube in a shell and tube heat ... drop through the exchanger is desired (D) Temperature of the incoming vapor is very high

Last Answer : (B) Supersaturated

In a 1-1 concurrent heat exchanger, if the tube side fluid outlet temperature is equal to the shell side fluid outlet temperature, then the LMTD is (A) ∞ (B) 0 (C) Equal to the difference between hot and cold fluids inlet temperature (D) Equal to the difference between hot fluid inlet temperature and cold fluid outlet temperature

Description : In a 1-1 concurrent heat exchanger, if the tube side fluid outlet temperature is equal to the shell side fluid outlet temperature, then the LMTD is (A) ∞ (B) 0 ... temperature (D) Equal to the difference between hot fluid inlet temperature and cold fluid outlet temperature

Last Answer : (B) 0

Fouling factor' used in the design of a multipass shell and tube heat exchanger is a (A) Non-dimensional factor (B) Factor of safety

Description : Fouling factor' used in the design of a multipass shell and tube heat exchanger is a (A) Non-dimensional factor (B) Factor of safety

Last Answer : (B) Factor of safety

. In a shell and tube heat exchanger, the tube side heat transfer co￾efficient just at the entrance of the tube is (A) Infinity (B) Zero (C) Same as average heat transfer co-efficient for tube side (D) None of these

Description : . In a shell and tube heat exchanger, the tube side heat transfer co￾efficient just at the entrance of the tube is (A) Infinity (B) Zero (C) Same as average heat transfer co-efficient for tube side (D) None of these

Last Answer : (A) Infinity

Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger, the shell pressure drop is maximum for orifice baffles (C) S.I. unit of fouling factor is Watt/m2 .°K (D) Longitudinal fins are used in extended surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Description : Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger ... surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Last Answer : (C) S.I. unit of fouling factor is Watt/m2 .°K

In case of a multipass shell and tube heat exchanger, providing a baffle on the shell side __________ the heat transfer rate. (A) Increases (B) Decreases (C) Does not affect (D) May increase or decrease, depends on the type of baffle

Description : In case of a multipass shell and tube heat exchanger, providing a baffle on the shell side __________ the heat transfer rate. (A) Increases (B) Decreases (C) Does not affect (D) May increase or decrease, depends on the type of baffle

Last Answer : (A) Increases

Pick out the wrong statement. (A) Heat transfer by radiation cannot occur across an absolute volume (B) In case of a shell and tube heat exchanger, the pressure drop through the shell is proportional to the number of times the fluid crosses the bundle between baffles (C) Propagation velocity for travel of heat radiation through vacuum is equal to the velocity of the light (D) The amount of heat involved in the condensation or vaporisation of 1 kg of a fluid is the same

Description : Pick out the wrong statement. (A) Heat transfer by radiation cannot occur across an absolute volume (B) In case of a shell and tube heat exchanger, the pressure drop through the shell is ... The amount of heat involved in the condensation or vaporisation of 1 kg of a fluid is the same

Last Answer : (A) Heat transfer by radiation cannot occur across an absolute volume