A temperature instrumentation system for an engine room console consists of a resistance temperature detector (RTD), a measuring bridge circuit, and a meter (or alarm circuit).Which of the following statements is true concerning the measuring bridge circu A. The input voltage varies in a linear fashion with temperature. B. The voltage across the center of the resistance bridge is always constant. C. The resistance bridge is said to be balanced when its output voltage is zero. D. The input voltage of the resistance bridge is the constant temperature signal.

A temperature instrumentation system for an engine room console consists of a resistance temperature detector (RTD), a measuring bridge circuit, and a meter (or alarm circuit).Which of the following statements is true concerning the measuring bridge circu A. The input voltage varies in a linear fashion with temperature. B. The voltage across the center of the resistance bridge is always constant. C. The resistance bridge is said to be balanced when its output voltage is zero. D. The input voltage of the resistance bridge is the constant temperature signal.
by

1 Answer

Answer :

Answer: C
by

Related questions

Which of the following statements concerning AC circuits is correct? A. The power factor of a resistive circuit is always zero. B. True power in an inductive circuit always equals apparent power. C. Inductive reactance varies directly with the frequency and the inductance. D. Total opposition to the flow of alternating current depends upon the amount of reactive power.

Description : Which of the following statements concerning AC circuits is correct? A. The power factor of a resistive circuit is always zero. B. True power in an inductive circuit always equals apparent power. ... . D. Total opposition to the flow of alternating current depends upon the amount of reactive power.

Last Answer : Answer: C

When a console indicating lamp burns out, attempts to renew it should not be made while maneuvering because _______________. A. the new lamp may be of a higher wattage and cause heat damage to the lens B. removing a faulty lamp usually causes an alarm to sound on the bridge C. attention should be paid only to engine orders D. a socket/wiring fault may cause a ground or short circuit to shut down a vital function

Description : When a console indicating lamp burns out, attempts to renew it should not be made while maneuvering because _______________. A. the new lamp may be of a higher wattage and cause heat damage to the lens ... D. a socket/wiring fault may cause a ground or short circuit to shut down a vital function

Last Answer : Answer: D

The illustrated circuit is a wheatstone bridge. If the meter 'G' reads 0 with the switch closed then ________. EL-0024 A. the current through R1 - R2 is equal to the current through R3 - Rx B. the voltage across b - d is equal to the voltage of E C. the resistance of Rx is equal to the resistance of R2 D. all the above are true

Description : The illustrated circuit is a wheatstone bridge. If the meter 'G' reads 0 with the switch closed then ________. EL-0024 A. the current through R1 - R2 is equal to the current through R3 - Rx B. the voltage ... of E C. the resistance of Rx is equal to the resistance of R2 D. all the above are true

Last Answer : Answer: A

Which sensor shown in the illustration develops its own conditioning and point setting and 'reports' directly to the 'annunciator'? EL-0094 A. Transducer B. Resistance Temperature Detector (RTD) C. Pressure Switch D. Thermocouple

Description : Which sensor shown in the illustration develops its own conditioning and point setting and 'reports' directly to the 'annunciator'? EL-0094 A. Transducer B. Resistance Temperature Detector (RTD) C. Pressure Switch D. Thermocouple

Last Answer : Answer: C

The purpose of a 'slew rate controller' in a circuit such as shown in the illustration is to ______________. EL-0096 A. limit the rate of change of a signal B. introduce a 'live zero' factor into the circuit C. shape the linear input into a non-linear output D. reduce air pressure to a value required by a combination circuit

Description : The purpose of a 'slew rate controller' in a circuit such as shown in the illustration is to ______________. EL-0096 A. limit the rate of change of a signal B. introduce a 'live zero' ... linear input into a non-linear output D. reduce air pressure to a value required by a combination circuit

Last Answer : Answer: A

What is resistance temperature detector (RTD) and mention some examples?

Description : What is resistance temperature detector (RTD) and mention some examples?

Last Answer : Resistance temperature detector is an instrument, which is used to measure temperature. This uses the property that the resistance of a metal changes (increases of decreases) with temperature. This ... calibrated to measure temperature. Different types of RTD's are Platinum, copper, nickel.  

Which of the following statements is true regarding the illustrated circuit? El-0069 A. This full wave bridge should never be used aboard ship because the ground on lead 'A' will show on the ship's ground detection system. B. Lead 'X' will always be positive (+) with respect to ground. C. This bridge circuit output will be direct current suitable for electronic circuits requiring voltage regulation. D. All the above are true.

Description : Which of the following statements is true regarding the illustrated circuit? El-0069 A. This full wave bridge should never be used aboard ship because the ground on lead 'A' will show on ... be direct current suitable for electronic circuits requiring voltage regulation. D. All the above are true.

Last Answer : Answer: B

Which of the following statements concerning a simple parallel resistance circuit is correct? A. The voltage drop across each resistor is the same. B. The total current flow equals the reciprocal of the sum of the individual currents. C. The total resistance equals the sum of the individual resistances. D. The total voltage equals the sum of the individual voltages across each resistance.

Description : Which of the following statements concerning a simple parallel resistance circuit is correct? A. The voltage drop across each resistor is the same. B. The total current flow equals the reciprocal ... resistances. D. The total voltage equals the sum of the individual voltages across each resistance.

Last Answer : Answer: A

Before measuring an unknown resistance with an ohmmeter, you should _____________. A. adjust the meter's pointer to mid-scale B. short the test leads and calibrate the meter reading to 'zero' C. change the meter's batteries D. center the meter's pointer at infinity

Description : Before measuring an unknown resistance with an ohmmeter, you should _____________. A. adjust the meter's pointer to mid-scale B. short the test leads and calibrate the meter reading to 'zero' C. change the meter's batteries D. center the meter's pointer at infinity

Last Answer : Answer: B

The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an autotransformer B. operational amplifier whose output controls a step-up voltage reactor C. amplitude modulator whose output drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor

Description : The voltage at the reference electrode of the circuit shown in the illustration is applied to the input of a/an ______________. EL-0090 A. class A detector whose output drives an ... drives an 2-stage isolation transformer D. magnetic amplifier whose output controls a saturable reactor

Last Answer : Answer: D

Which of the following statements is true concerning simple parallel resistance circuits? A. The total current flow equals the sum of the individual currents. B. The total current flow equals the reciprocal of the sum of the individual currents. C. The total resistance equals the sum of the individual resistance. D. The total voltage equals the sum of the individual voltages across each resistance.

Description : Which of the following statements is true concerning simple parallel resistance circuits? A. The total current flow equals the sum of the individual currents. B. The total current flow equals the ... resistance. D. The total voltage equals the sum of the individual voltages across each resistance.

Last Answer : Answer: A

Describe construction and working of Resistance Temperature Detector (RTD).

Description : Describe construction and working of Resistance Temperature Detector (RTD).

Last Answer : RTD:  Construction and working: Resistance thermometer bulbs consist of a coil of fine wire wound or in a frame of insulating material. The resistance wire itself must be homogeneous in order to ... surrounding it. Thus RTD is used to measure temperature in terms of change in resistance.

When using a multimeter for resistance measurements, it should be calibrated by clipping the loose ends of the leads together and _____________. A. setting the instrument pointer at 'zero' ohms B. adjusting the line voltage to calibrate the instrument C. plugging each end of one test lead into the plus and minus terminals D. using a special purpose resistance measuring instrument (a bridge)

Description : When using a multimeter for resistance measurements, it should be calibrated by clipping the loose ends of the leads together and _____________. A. setting the instrument pointer at 'zero' ohms B. ... the plus and minus terminals D. using a special purpose resistance measuring instrument (a bridge)

Last Answer : Answer: A

Coast Guard Regulations (46 CFR) require manual contactors for operating the general emergency alarm on tank vessels to be located in the navigating bridge, engine room and the ____________. A. deck officers' quarters furthest from the engine room B. galley / dining room areas C. crew accommodations and sleeping spaces D. engineering officers' quarters furthest from the bridge

Description : Coast Guard Regulations (46 CFR) require manual contactors for operating the general emergency alarm on tank vessels to be located in the navigating bridge, engine room and the ____________. A ... C. crew accommodations and sleeping spaces D. engineering officers' quarters furthest from the bridge

Last Answer : Answer: A

Considering the function of the circuit shown in the illustration, what is the purpose of supplying the thrust lever potentiometers with both (+) and (-) 15 volts? EL-0095 A. To select which lever (bridge or engine room) is active. B. So the circuit can differentiate between ahead and astern commands. C. To provide an alternate voltage supply if the other fails. D. So as to automatically select the position of Relay #

Description : Considering the function of the circuit shown in the illustration, what is the purpose of supplying the thrust lever potentiometers with both (+) and (-) 15 volts? EL-0095 A. To select which ... alternate voltage supply if the other fails. D. So as to automatically select the position of Relay #

Last Answer : Answer: B

For console circuit card 'LLEA' as shown in the illustration at coordinates '63R/S', the input(s) and output(s) are respectively on pin numbers ____________. EL-0100 A. '5' and '3' & '4' B. '2' & '3' and '5' & '6' C. '5' & '6' and '2' & '3' D. '3' & '4' and '5'

Description : For console circuit card 'LLEA' as shown in the illustration at coordinates '63R/S', the input(s) and output(s) are respectively on pin numbers ____________. EL-0100 A. '5' and '3' & '4' B. '2' & '3' and '5' & '6' C. '5' & '6' and '2' & '3' D. '3' & '4' and '5'

Last Answer : Answer: D

In the illustrated circuit, if the input to leads 'B' and 'Y' was 24 VDC the output between 'A' and 'X' will be _________. EL-0069 A. 24 VDC B. 22.8 VDC, 24 VDC minus the 1.2 VDC voltage drop across two diodes C. undeterminable without knowing the turns ratio of the transformer D. 0 VDC

Description : In the illustrated circuit, if the input to leads 'B' and 'Y' was 24 VDC the output between 'A' and 'X' will be _________. EL-0069 A. 24 VDC B. 22.8 VDC, 24 VDC minus the 1.2 VDC voltage drop across two diodes C. undeterminable without knowing the turns ratio of the transformer D. 0 VDC

Last Answer : Answer: D

Before measuring an unknown resistance with an ohmmeter, you should _____________. A. adjust the meter's pointers to mid-scale B. change the meter's batteries C. center the meter's pointer at infinity D. short the test leads and calibrate the meter

Description : Before measuring an unknown resistance with an ohmmeter, you should _____________. A. adjust the meter's pointers to mid-scale B. change the meter's batteries C. center the meter's pointer at infinity D. short the test leads and calibrate the meter

Last Answer : Answer: D

In the illustration, the signal from the device connected to terminals 18 and 19 is __________. EL-0046 A. prime mover speed feedback B. loss of control alarm when comparing with the input signal from the resistor at the top of the speed sensing circuit card C. hall effect current to detect slip between the prime mover and the alternator D. to shut down the prime mover if overspeeding

Description : In the illustration, the signal from the device connected to terminals 18 and 19 is __________. EL-0046 A. prime mover speed feedback B. loss of control alarm when comparing with the input signal ... slip between the prime mover and the alternator D. to shut down the prime mover if overspeeding

Last Answer : Answer: A

A faulty 'function generator' shown in the illustration may prevent _____________. EL-0095 A. proper pitch control from both the 'bridge' and 'engine room thrust levers' B. the 'split potentiometer's' ability to control pitch C. the pitch meter from indicating accurately D. relays #2 and/or #3 from energizing

Description : A faulty 'function generator' shown in the illustration may prevent _____________. EL-0095 A. proper pitch control from both the 'bridge' and 'engine room thrust levers' B. the 'split potentiometer ... control pitch C. the pitch meter from indicating accurately D. relays #2 and/or #3 from energizing

Last Answer : Answer: A

The meter indicating the position of the 'bridge Thrust lever' shown in the illustration is located ___________________. EL-0095 A. in the Engine Control Room B. on the Bridge C. in the Captain's office D. in the Chief Engineer's office

Description : The meter indicating the position of the 'bridge Thrust lever' shown in the illustration is located ___________________. EL-0095 A. in the Engine Control Room B. on the Bridge C. in the Captain's office D. in the Chief Engineer's office

Last Answer : Answer: A

A potentiometer circuit is setup as shown. The potential gradient across the potentiometer wire is `k "volt"//cm` and the ammeter present in the circu

Description : A potentiometer circuit is setup as shown. The potential gradient across the potentiometer wire is `k "volt"//cm` and the ammeter present in the circu

Last Answer : A potentiometer circuit is setup as shown. The potential gradient across the potentiometer wire is `k "volt"//cm` and ... (2)` D. `kl_(1)"and"kl_(2)`

If Relay #5 changed contact position grounding the 'auto' input to the 'pitch controller module', pitch control would be effected by the _________________. EL-0095 A. pitch feedback potentiometer B. Engine room thrust split potentiometer C. Engine room thrust lever only D. Bridge thrust lever only

Description : If Relay #5 changed contact position grounding the 'auto' input to the 'pitch controller module', pitch control would be effected by the _________________. EL-0095 A. pitch feedback potentiometer B. Engine room thrust split potentiometer C. Engine room thrust lever only D. Bridge thrust lever only

Last Answer : Answer: B

Under which of the listed conditions can the engine room retake the throttle control from the bridge? A. Any time it is deemed necessary. B. Only with the master's permission. C. After a 10 minute delay to the input command. D. Only after the throttle has been placed in stop.

Description : Under which of the listed conditions can the engine room retake the throttle control from the bridge? A. Any time it is deemed necessary. B. Only with the master's permission. C. After a 10 minute delay to the input command. D. Only after the throttle has been placed in stop.

Last Answer : Answer: A

Which of the following statements is true concerning a stepdown transformer in an operating AC power circuit? A. Voltage and current will both be increased. B. Voltage and current will both be decreased C. Voltage decreases as current increases. D. Voltage increases as current decreases.

Description : Which of the following statements is true concerning a stepdown transformer in an operating AC power circuit? A. Voltage and current will both be increased. B. Voltage and current will both be decreased C. Voltage decreases as current increases. D. Voltage increases as current decreases.

Last Answer : Answer: C

Which of the following statements is true concerning a polyphase synchronous propulsion motor? A. The motor is started as an induction motor. B. Resistance is gradually added to the rotor circuit. C. The starting current is held below the rated current. D. The field winding is energized for starting purposes only.

Description : Which of the following statements is true concerning a polyphase synchronous propulsion motor? A. The motor is started as an induction motor. B. Resistance is gradually added to the rotor circuit. C. ... is held below the rated current. D. The field winding is energized for starting purposes only.

Last Answer : Answer: A

The term responsivity as it applies to a light detector is best described as ∙ A. the time required for the signal to go from 10 to 90 percent of maximum amplitude ∙ B. the ratio of the diode output current to the input optical power ∙ C. the ratio of the input power to output power ∙ D. the ratio of output current to input current

Description : The term responsivity as it applies to a light detector is best described as ∙ A. the time required for the signal to go from 10 to 90 percent of maximum amplitude ∙ B. the ratio of the diode ... . the ratio of the input power to output power ∙ D. the ratio of output current to input current

Last Answer : the ratio of the diode output current to the input optical power

The input to a coherent detector is DSB-SC signal plus noise. The noise at the detector output is: ...

Description : The input to a coherent detector is DSB-SC signal plus noise. The noise at the detector output is:  (1) The in-phase component (2) The quadrature-component (3) Zero (4) The envelope

Last Answer : The input to a coherent detector is DSB-SC signal plus noise. The noise at the detector output is: Zero.

The component labeled 'CR1' in the circuit shown in the illustration __________________. EL-0085 A. varies its anode/cathode polarity depending on 'RL' current B. rectifies the varying voltage from the collector of 'Q1' C. acts as a low capacitive reactance to smooth ripple D. establishes a constant reference voltage for the base of 'Q1'

Description : The component labeled 'CR1' in the circuit shown in the illustration __________________. EL-0085 A. varies its anode/cathode polarity depending on 'RL' current B. rectifies the varying voltage from the ... reactance to smooth ripple D. establishes a constant reference voltage for the base of 'Q1'

Last Answer : Answer: D

An electric tachometer receives the engine speed signal from a _______________. A. small generator mounted on the engine B. bimetallic sensing device C. stroboscopic sensing device D. vibrating reed meter generating a voltage proportionate to engine speed

Description : An electric tachometer receives the engine speed signal from a _______________. A. small generator mounted on the engine B. bimetallic sensing device C. stroboscopic sensing device D. vibrating reed meter generating a voltage proportionate to engine speed

Last Answer : Answer: A

The 'function generator' of the control circuit illustrated _______________. EL-0095 A. can be programmed to produce a non-linear output for a linear input depending on operating conditions B. is used for controlling relay contacts' positions in selection circuits C. automatically selects which or how many engines are needed for a required vessel speed D. all of the above

Description : The 'function generator' of the control circuit illustrated _______________. EL-0095 A. can be programmed to produce a non-linear output for a linear input depending on operating conditions B. is used for ... which or how many engines are needed for a required vessel speed D. all of the above

Last Answer : Answer: A

The sensor connected to 'signal conditioner' (6000F125) shown in the illustration is a/an ______________. EL-0094 A. thermocouple B. transducer C. inverter D. RTD

Description : The sensor connected to 'signal conditioner' (6000F125) shown in the illustration is a/an ______________. EL-0094 A. thermocouple B. transducer C. inverter D. RTD

Last Answer : Answer: B

The sensor connected to 'signal conditioner' (6000AH170) shown in the illustration is a/an _____________. EL-0094 A. thermocouple B. transducer C. inverter D. RTD

Description : The sensor connected to 'signal conditioner' (6000AH170) shown in the illustration is a/an _____________. EL-0094 A. thermocouple B. transducer C. inverter D. RTD

Last Answer : Answer: A

The sensor connected to 'signal conditioner' (6000F085) shown in the illustration is a/an ______________. EL-0094 A. thermocouple B. transducer C. inverter D. RTD

Description : The sensor connected to 'signal conditioner' (6000F085) shown in the illustration is a/an ______________. EL-0094 A. thermocouple B. transducer C. inverter D. RTD

Last Answer : Answer: D

In an AC circuit, the inductive reactance of a coil varies with the _______________. A. resistance of the circuit B. frequency of the circuit C. voltage of the circuit D. current of the circuit

Description : In an AC circuit, the inductive reactance of a coil varies with the _______________. A. resistance of the circuit B. frequency of the circuit C. voltage of the circuit D. current of the circuit

Last Answer : Answer: B

The advantage of using the illustrated circuit configuration is _________. EL-0045 A. high input resistance B. high current gain C. the best stability with an increase in temperature D. the input and output are 180 degrees out of phase

Description : The advantage of using the illustrated circuit configuration is _________. EL-0045 A. high input resistance B. high current gain C. the best stability with an increase in temperature D. the input and output are 180 degrees out of phase

Last Answer : Answer: C

One method of troubleshooting digital circuits in a console is to ___________. A. supply alternate logic levels at the input(s) and test for change of state conditions at the output B. ground all inputs and test for a logic '1' at the output C. open all inputs and test for a logic '0' at the output D. vary each input smoothly from 0-10 volts and test for similar variance at the output

Description : One method of troubleshooting digital circuits in a console is to ___________. A. supply alternate logic levels at the input(s) and test for change of state conditions at the output B. ground all ... output D. vary each input smoothly from 0-10 volts and test for similar variance at the output

Last Answer : Answer: A

A disadvantage of using the configuration in the illustrated circuit is _________. EL-0045 A. no current gain B. high input resistance C. high voltage gain D. becomes unstable with an increase of ambient temperature

Description : A disadvantage of using the configuration in the illustrated circuit is _________. EL-0045 A. no current gain B. high input resistance C. high voltage gain D. becomes unstable with an increase of ambient temperature

Last Answer : Answer: A

Which of the listed devices may be installed on a large diesel-electric alternating current propulsion generator? A. Temperature detector coils inserted in the stator slots for measuring stator temperature. B. A CO2 fire extinguishing system. C. Electric space heaters to prevent condensation of moisture. D. All of the above.

Description : Which of the listed devices may be installed on a large diesel-electric alternating current propulsion generator? A. Temperature detector coils inserted in the stator slots for measuring stator temperature. B. ... . C. Electric space heaters to prevent condensation of moisture. D. All of the above.

Last Answer : Answer: D

Which of the listed devices may be installed on a large turbo-electric alternating current propulsion generator? A. Temperature detector coils inserted in the stator slots for measuring stator temperature. B. A CO2 fire extinguishing system. C. Electric space heaters to prevent condensation of moisture. D. All of the above.

Description : Which of the listed devices may be installed on a large turbo-electric alternating current propulsion generator? A. Temperature detector coils inserted in the stator slots for measuring stator temperature. B. A ... . C. Electric space heaters to prevent condensation of moisture. D. All of the above.

Last Answer : Answer: D

Draw the practical AM diode detector circuit. Sketch its input and output waveforms.

Description : Draw the practical AM diode detector circuit. Sketch its input and output waveforms. 

Last Answer : Practical AM diode detector 1. Skip distance:-Skip distance is defined as the shortest distance from a transmitter, measured along the surface of earth at which a sky wave of fixed frequency ... had taken place from a surface located at a greater height, called Virtual height of this layer.

One of the FM signal generator control which varies the phase of the modulating voltage applied to the oscillator of the sweep generator A. Band control B. Phase control C. Marker amplitude control D. Sweep output control

Description : One of the FM signal generator control which varies the phase of the modulating voltage applied to the oscillator of the sweep generator A. Band control B. Phase control C. Marker amplitude control D. Sweep output control

Last Answer : B. Phase control

Shear stress in a fluid flowing in a round pipe (A) Varies parabolically across the cross-section(B) Remains constant over the cross-section(C) Is zero at the centre and varies linearly with the radius(D) Is zero at the wall and increases linearly to the centre

Description : Shear stress in a fluid flowing in a round pipe (A) Varies parabolically across the cross-section (B) Remains constant over the cross-section (C) Is zero at the centre and varies linearly with the radius (D) Is zero at the wall and increases linearly to the centre

Last Answer : (C) Is zero at the centre and varies linearly with the radius

Velocity distribution for flow between two fixed parallel plates (A) Varies parabolically across the section (B) Is constant over the entire cross-section (C) Is zero at the plates and increases linearly to the mid-plane (D) None of these

Description : Velocity distribution for flow between two fixed parallel plates (A) Varies parabolically across the section (B) Is constant over the entire cross-section (C) Is zero at the plates and increases linearly to the mid-plane (D) None of these

Last Answer : (A) Varies parabolically across the section