When soldering a printed circuit board component, you should be careful to prevent damage by _________. A. quickly heating the joints, using a high wattage iron B. using the soldering iron tip sparingly C. using only acid cord solder D. applying mechanical pressure to the joints being soldered

Question

When soldering a printed circuit board component, you should be careful to prevent damage by _________. A. quickly heating the joints, using a high wattage iron B. using the soldering iron tip sparingly C. using only acid cord solder D. applying mechanical pressure to the joints being soldered

asked Jan 4, 2022 by anonymous

1 Answer

Answer :

Answer: B

answered Jan 4, 2022 by anonymous

Related questions

Why is it a poor practice to use a high wattage soldering iron when soldering or desoldering components on a printed circuit board? A. The circuit board will blister and warp. B. The foil wire bonded to the board may come loosened from the board. C. The circuit board has a low melting temperature. D. The solder is kept to a dull heat dissipating finish.

Description : Why is it a poor practice to use a high wattage soldering iron when soldering or desoldering components on a printed circuit board? A. The circuit board will blister and warp. B. The foil wire bonded ... board has a low melting temperature. D. The solder is kept to a dull heat dissipating finish.

Last Answer : Answer: B

If a delicate component must be soldered into a circuit, the component may be protected from the heat of the soldering process by _____________. A. operating the soldering gun not more than 60 seconds at a time B. using a thermal shunt C. pre-oxidizing the leads to be soldered D. coating the leads to be soldered with a light oil film

Description : If a delicate component must be soldered into a circuit, the component may be protected from the heat of the soldering process by _____________. A. operating the soldering gun not more than 60 seconds at ... oxidizing the leads to be soldered D. coating the leads to be soldered with a light oil film

Last Answer : Answer: B

Why are small-wattage soldering irons not used to solder large conductors?

Description : Why are small-wattage soldering irons not used to solder large conductors?

Last Answer : Although its temperature is as high as the larger irons, it does not have thermal inertia.

When a solid-state component of an electronic circuit is mounted to a metallic mass, the general purpose of that mass is to ____________. A. prevent vibration damage to delicate components B. prevent mechanical damage to solid-state components C. dissipate stray magnetic currents D. act as a heat sink

Description : When a solid-state component of an electronic circuit is mounted to a metallic mass, the general purpose of that mass is to ____________. A. prevent vibration damage to delicate components B. prevent ... damage to solid-state components C. dissipate stray magnetic currents D. act as a heat sink

Last Answer : Answer: D

When troubleshooting an electronic circuit, a cold solder joint can be located with the aid of an ohmmeter. Once the problem has been located, you should _________________. A. reheat the circuit in an oven to an even temperature and recheck with an ohmmeter B. reheat the connection with a match and recheck with an ohmmeter C. reheat connection with a soldering tool and recheck with an ohmmeter D. do nothing as this is the normal condition

Description : When troubleshooting an electronic circuit, a cold solder joint can be located with the aid of an ohmmeter. Once the problem has been located, you should _________________. A. reheat the circuit in an ... a soldering tool and recheck with an ohmmeter D. do nothing as this is the normal condition

Last Answer : Answer: C

As shown in the illustration, the circuit has been on the line for several days when component 'E1' burns out. The operator receives an alarm, switches over 'B' to energize the standby component 'E2' and tells the electrician to renew 'E1'. The opera EL-0058 A. burned out rapidly due to an overused and overheated connection terminal which in turn led to 'C' burning out B. installation developed an accidental connection to 'D' and short-circuited the main line resulting in overloaded fuses just after the master switch C. is a 110 volt DC device being used in a 115 volt AC circuit and will conduct only on the positive half-cycle D. is of a lower wattage rating than required for the circuit therefore limiting the current through the alarm relay which will not pick up

Description : As shown in the illustration, the circuit has been on the line for several days when component 'E1' burns out. The operator receives an alarm, switches over 'B' to energize the standby ... than required for the circuit therefore limiting the current through the alarm relay which will not pick up

Last Answer : Answer: D

Which of the following precautions should be taken when troubleshooting various power circuits using a common solenoid-type mechanical voltage tester (wiggins)? A. Never use this tester on circuits greater than 60 Hz, as the coil's resultant high impedance lowers current and magnetic pull. The tester may not register dangerous voltages. B. Always remember that the unit is polarity sensitive and if used on DC circuits reversing the leads may result in high temperatures within the tester. C. Never connect the device to circuits where potentials greater than 120 volts may be present, as the coil's extremely fine wire cannot withstand more than a few amps. D. Always pre-set the meter to the next higher range than the amount of voltage expected in the circuit in order to prevent damage from an

Description : Which of the following precautions should be taken when troubleshooting various power circuits using a common solenoid-type mechanical voltage tester (wiggins)? A. Never use this tester on circuits greater ... voltage expected in the circuit in order to prevent damage from an off-scale reading.

Last Answer : Answer: A

Use of flux during soldering is done to (A) Increase fluidity of solder by lowering its melting temperature (B) Prevent oxide formation (C) Wash away surplus solder (D) Full up the joint gap

Description : Use of flux during soldering is done to (A) Increase fluidity of solder by lowering its melting temperature (B) Prevent oxide formation (C) Wash away surplus solder (D) Full up the joint gap

Last Answer : (B) Prevent oxide formation

Which of the procedures listed could result in damaging a transistor beyond repair? A. Applying incorrect polarity to the collector circuit. B. Applying excessive voltage to the input circuit. C. Careless soldering which would overheat the transistor. D. All of the above.

Description : Which of the procedures listed could result in damaging a transistor beyond repair? A. Applying incorrect polarity to the collector circuit. B. Applying excessive voltage to the input circuit. C. Careless soldering which would overheat the transistor. D. All of the above.

Last Answer : Answer: D

When a console indicating lamp burns out, attempts to renew it should not be made while maneuvering because _______________. A. the new lamp may be of a higher wattage and cause heat damage to the lens B. removing a faulty lamp usually causes an alarm to sound on the bridge C. attention should be paid only to engine orders D. a socket/wiring fault may cause a ground or short circuit to shut down a vital function

Description : When a console indicating lamp burns out, attempts to renew it should not be made while maneuvering because _______________. A. the new lamp may be of a higher wattage and cause heat damage to the lens ... D. a socket/wiring fault may cause a ground or short circuit to shut down a vital function

Last Answer : Answer: D

In electronic circuits, DC voltages can be positive (+) or negative (-) when measured with respect to the _________. A. printed circuit board 'common' trace B. chassis, console frame or hull 'ground' C. analogue or digital circuitry 'common' bus D. all of the above

Description : In electronic circuits, DC voltages can be positive (+) or negative (-) when measured with respect to the _________. A. printed circuit board 'common' trace B. chassis, console frame or hull 'ground' C. analogue or digital circuitry 'common' bus D. all of the above

Last Answer : Answer: D

How should excess solder be removed from a hot soldering iron?

Description : How should excess solder be removed from a hot soldering iron?

Last Answer : By use of a cleaning cloth.

Why must items to be soldered be cleaned just prior to the soldering process?

Description : Why must items to be soldered be cleaned just prior to the soldering process?

Last Answer : Solder will not adhere to dirty, greasy, or oxidized surfaces.

Flux aids in soldering by removing what from surfaces to be soldered?

Description : Flux aids in soldering by removing what from surfaces to be soldered?

Last Answer : Oxides.

When replacing component 'B' of the circuit shown in the illustration, it is important to know that ____________. EL-0081 A. it is polarity sensitive and must be inserted as indicated on its base B. there is a danger of phosphor poisoning should 'B''s bulb break C. component 'D' must be closed during the replacement to provide the capacitor's initial charge D. it must match the circuit voltage and component 'C' wattage

Description : When replacing component 'B' of the circuit shown in the illustration, it is important to know that ____________. EL-0081 A. it is polarity sensitive and must be inserted as indicated on its ... provide the capacitor's initial charge D. it must match the circuit voltage and component 'C' wattage

Last Answer : Answer: D

When changing out component 'B' of the circuit shown in the illustration, it is important to know that ____________. EL-0081 A. it is polarity sensitive and must be inserted as indicated on its base B. there is a danger of phosphor poisoning should 'B''s bulb break C. component 'D' must be closed during the replacement to provide the capacitor's initial charge D. it must match the circuit voltage and component 'C' wattage

Description : When changing out component 'B' of the circuit shown in the illustration, it is important to know that ____________. EL-0081 A. it is polarity sensitive and must be inserted as indicated on its ... provide the capacitor's initial charge D. it must match the circuit voltage and component 'C' wattage

Last Answer : Answer: D

During the start-up of the circuit shown in the illustration, it is noted that the ends of component 'C' remain lighted but the tube does not illuminate. The cause of this problem is ____________. EL-0081 A. component 'A' is open B. component 'D' is closed C. component 'C' is the wrong wattage D. component 'B' contacts are stuck closed

Description : During the start-up of the circuit shown in the illustration, it is noted that the ends of component 'C' remain lighted but the tube does not illuminate. The cause of this problem is ____________. EL- ... ' is closed C. component 'C' is the wrong wattage D. component 'B' contacts are stuck closed

Last Answer : Answer: D

When troubleshooting electronic equipment, you should use a high impedance multimeter ________________. A. to prevent excess current flow through the meter that would damage it B. for AC measurements only and a low resistance meter for DC measurements C. whenever a low impedance meter is not available, regardless of the components being tested D. so as not to load down the circuit and obtain erroneous voltage readings

Description : When troubleshooting electronic equipment, you should use a high impedance multimeter ________________. A. to prevent excess current flow through the meter that would damage it B. for AC measurements only ... being tested D. so as not to load down the circuit and obtain erroneous voltage readings

Last Answer : Answer: D

When does most printed circuit board damage occur?

Description : When does most printed circuit board damage occur?

Last Answer : During disassembly or repair.

What is the type of solder that would be used in hard soldering?

Description : What is the type of solder that would be used in hard soldering?

Last Answer : Need answer

What should be done to a soldering iron tip that is pitted?

Description : What should be done to a soldering iron tip that is pitted?

Last Answer : File the tip until it is smooth and retin it.

What determines the shape and size of a soldering iron tip?

Description : What determines the shape and size of a soldering iron tip?

Last Answer : The type of work to be done.

While troubleshooting a circuit in an engine room central control console, a resistor is suspected of being faulty. Which of the following precautions must be observed if an ohmmeter is to be used to check its value? A. Correct polarity must be observed because reverse bias will damage the component. B. Meter leads must not be twisted so as to cancel out the individual magnetic fields. C. Resistor's circuit must be de-energized and at least one end of the component isolated. D. The meter case must be grounded prior to attaching the leads.

Description : While troubleshooting a circuit in an engine room central control console, a resistor is suspected of being faulty. Which of the following precautions must be observed if an ohmmeter is to be used to ... of the component isolated. D. The meter case must be grounded prior to attaching the leads.

Last Answer : Answer: C

What is the wattage of a heating element drawing a current of 30 amperes, at 120 volts? A. 30 watts B. 99.97 watts C. 360 watts D. 3600 watts

Description : What is the wattage of a heating element drawing a current of 30 amperes, at 120 volts? A. 30 watts B. 99.97 watts C. 360 watts D. 3600 watts

Last Answer : Answer: D

How do you prevent excessive heat buildup on an area of a board when soldering multilead components?

Description : How do you prevent excessive heat buildup on an area of a board when soldering multilead components?

Last Answer : Use a skipping pattern

To avoid damaging the components of a printed circuit board when testing it with a DC volt-ohmmeter, you should _______. A. ground the board B. avoid reversing the polarity of the leads C. isolate sensitive components with heat sinks D. all of the above

Description : To avoid damaging the components of a printed circuit board when testing it with a DC volt-ohmmeter, you should _______. A. ground the board B. avoid reversing the polarity of the leads C. isolate sensitive components with heat sinks D. all of the above

Last Answer : Answer: B

In electronic circuitry, the abbreviation 'PCB' commonly means ______________. A. pulse coded binary B. printed circuit board C. poly-coated braid D. personal computer bits

Description : In electronic circuitry, the abbreviation 'PCB' commonly means ______________. A. pulse coded binary B. printed circuit board C. poly-coated braid D. personal computer bits

Last Answer : Answer: B

Tightly knit metal braid wire can be used with a printed circuit board when ___________. A. conductor flexibility is required B. desoldering components in the circuit C. electrically produced magnetic fluxes would cause inaccuracies in adjacent components D. reactance in the circuit must be kept to a minimum

Description : Tightly knit metal braid wire can be used with a printed circuit board when ___________. A. conductor flexibility is required B. desoldering components in the circuit C. electrically produced magnetic ... cause inaccuracies in adjacent components D. reactance in the circuit must be kept to a minimum

Last Answer : Answer: B

The small circular symbols to which wire '52N57E' is connected at coordinates '57L' and '57P' shown in the illustration represent ___________________. EL-0100 A. relay contact solder points B. wire wrap connections C. terminal board screws D. switch contact terminals

Description : The small circular symbols to which wire '52N57E' is connected at coordinates '57L' and '57P' shown in the illustration represent ___________________. EL-0100 A. relay contact solder points B. wire wrap connections C. terminal board screws D. switch contact terminals

Last Answer : Answer: C

In the illustrated motor controller circuit, which statment is true? EL-0023 A. The high and low speed lights operate at less than line voltage with a resistor in series. B. This controller can be converted for use with a three phase motor by connecting the L3 lead to the LS contact attached to the overload relay. C. The lights must be rated at a wattage equal or greater that the motor output wattage. D. The wattage of the high speed light must be greater than the wattage of the low speed light.

Description : In the illustrated motor controller circuit, which statment is true? EL-0023 A. The high and low speed lights operate at less than line voltage with a resistor in series. B. This controller can be ... . The wattage of the high speed light must be greater than the wattage of the low speed light.

Last Answer : Answer: A

In the illustration, the diode between terminals 16 and 17 is to _________. EL-0046 A. insure that the voltage across the governor coil (EG-3P) never exceeds .6 VDC B. compensate for the temperature difference of the governor oil heating up C. protect the electronic governor from counter EMF D. act as a filter to prevent hunting

Description : In the illustration, the diode between terminals 16 and 17 is to _________. EL-0046 A. insure that the voltage across the governor coil (EG-3P) never exceeds .6 VDC B. compensate for the ... heating up C. protect the electronic governor from counter EMF D. act as a filter to prevent hunting

Last Answer : Answer: C

One of the following is a possible cause for a slow drift of frequency in a self-exited transmitter oscillator circuits resulting to a poor frequency stability. A. Loose shielding B. Heating of capacitor in the oscillator C. Poor soldered connections D. Faulty capacitor, resistor, tubes or resistors

Description : One of the following is a possible cause for a slow drift of frequency in a self-exited transmitter oscillator circuits resulting to a poor frequency stability. A. Loose shielding B. ... capacitor in the oscillator C. Poor soldered connections D. Faulty capacitor, resistor, tubes or resistors

Last Answer : B. Heating of capacitor in the oscillator

Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections B. Power supply voltage changes C. Loose connections in the oscillator, amplifier, or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Description : Which of the following is one of the possible causes for a slow drift of frequency in a self exited transmitter oscillator circuits resulting to a poor frequency stability? A. Poor soldered connections ... , or antenna circuits D. DC and RF heating of resistors, causing then to change values.

Last Answer : D. DC and RF heating of resistors, causing then to change values.

The proper way to apply plastic electrical tape to an electric cable splice is to _____________. A. apply tape to the braided cover, but avoid touching it B. wind the tape so that each turn overlaps the turn before it C. apply the tape in one non-overlapping layer only D. heat the tape with a soldering iron for good bonding

Description : The proper way to apply plastic electrical tape to an electric cable splice is to _____________. A. apply tape to the braided cover, but avoid touching it B. wind the tape so that each turn overlaps ... tape in one non-overlapping layer only D. heat the tape with a soldering iron for good bonding

Last Answer : Answer: B

Can applying coconut oil before bleaching my hair prevent less damage?

Description : Can applying coconut oil before bleaching my hair prevent less damage?

Last Answer : answer:My mother was a hairstylist for several years and her rule of thumb for coloring hair was always that the hair should be as clean as possible before applying chemicals. However, I did some poking around and ... and go to sleep. 3. Bleach hair as usual the next day with oil still in the hair.

When a lead is soldered to a pad without passing through the board, it is known as what type of termination?

Description : When a lead is soldered to a pad without passing through the board, it is known as what type of termination?

Last Answer : On-the-board termination.

Of the following stimuli, which is known to trigger an episode of autonomic hyperreflexia in the patient who has suffered a spinal cord injury? a) Applying a blanket over the patient An object on the skin or skin pressure may precipitate an autonomic hyperreflexic episode.

Description : Of the following stimuli, which is known to trigger an episode of autonomic hyperreflexia in the patient who has suffered a spinal cord injury? a) Applying a blanket over the patient An ... lower blood pressure. d) Voiding The most common cause of autonomic hyperreflexia is a distended bladder.

Last Answer : a) Applying a blanket over the patient An object on the skin or skin pressure may precipitate an autonomic hyperreflexic episode.

. Lap joints are preferred over butt joints in soldering/brazing, because these joints are (A) Weaker in tension but stronger in shear (B) Weaker in shear but stronger in tension (C) Stronger in both shear and tension (D) The lap joints are easily made

Description : . Lap joints are preferred over butt joints in soldering/brazing, because these joints are (A) Weaker in tension but stronger in shear (B) Weaker in shear but stronger in tension (C) Stronger in both shear and tension (D) The lap joints are easily made

Last Answer : r: Option D

In the illustration what is the minimum wattage needed for a 3 ohm resistor with a 12 VDC power source in circuit 'A'? EL-0041 A. 12 watts B. 48 watts C. 64 watts D. 232 watts

Description : In the illustration what is the minimum wattage needed for a 3 ohm resistor with a 12 VDC power source in circuit 'A'? EL-0041 A. 12 watts B. 48 watts C. 64 watts D. 232 watts

Last Answer : Answer: B

As a result of a mechanical malfunction in one of the ship's service generators operating in parallel, you must secure that generator. In order to prevent a possible overload to the remaining generator, which of the following sequential courses of actio A. Trip the malfunctioning generator's circuit breaker and prime mover throttle trip. B. Trip all nonvital distribution feeder circuit breakers, the malfunctioning generator's circuit breaker, and the prime mover throttle trip. C. Trip the malfunctioning generator's circuit breaker and distribution feeder circuit breakers. D. Trip all nonvital distribution feeder circuit breakers, the malfunctioning prime mover turbine throttle trip, and the generator circuit breaker.

Description : As a result of a mechanical malfunction in one of the ship's service generators operating in parallel, you must secure that generator. In order to prevent a possible overload to the ... feeder circuit breakers, the malfunctioning prime mover turbine throttle trip, and the generator circuit breaker.

Last Answer : Answer: B

In order to prevent the winch shown in the illustration from turning while troubleshooting the controller circuit, _________________. EL-0102 A. set the dynamic brake by clamping contact 'DB' closed B. set the mechanical brake by the jackscrew provided C. disconnect the brake solenoid at 'B1' and 'B2' D. open the test link preventing current flow to the armature

Description : In order to prevent the winch shown in the illustration from turning while troubleshooting the controller circuit, _________________. EL-0102 A. set the dynamic brake by clamping contact 'DB' closed B. set the ... at 'B1' and 'B2' D. open the test link preventing current flow to the armature

Last Answer : Answer: D

When troubleshooting electronic equipment, the FIRST step to be taken before testing the circuit voltage is to _________. A. set the meter to the lowest range B. check the voltage supply from the power source C. remove the suspected component D. check the current flow through the circuit

Description : When troubleshooting electronic equipment, the FIRST step to be taken before testing the circuit voltage is to _________. A. set the meter to the lowest range B. check the voltage supply from the power source C. remove the suspected component D. check the current flow through the circuit

Last Answer : Answer: B

The illustrated test is being conducted on the motor shown in the illustration, if the lamp lights dimly then ________. EL-0027 A. the bulb needs to be changed to one with a higher wattage rating B. safety procedures need to be reviewed because the test presents a severe electrical shock hazard to the person conducting the test and anyone touching the motor frame C. the disconnected wires are touching, they need to be seperated and the test conducted again D. a ground or partial ground is indicated, a check with a megger should confirm the lamp test

Description : The illustrated test is being conducted on the motor shown in the illustration, if the lamp lights dimly then ________. EL-0027 A. the bulb needs to be changed to one with a higher wattage rating B. ... D. a ground or partial ground is indicated, a check with a megger should confirm the lamp test

Last Answer : Answer: D

When troubleshooting a console circuit card suspected of being faulty, first check operating voltages, clean the card and then _________________. A. make sure wired connections and push-on connectors are tight B. test each resistor and capacitor on the card with an ohmmeter C. check the continuity of all printed circuit traces with an ohmmeter D. measure the gain of each transistor or integrated circuit

Description : When troubleshooting a console circuit card suspected of being faulty, first check operating voltages, clean the card and then _________________. A. make sure wired connections and push-on connectors ... circuit traces with an ohmmeter D. measure the gain of each transistor or integrated circuit

Last Answer : Answer: A

When troubleshooting a console circuit card suspected of being faulty, first check for proper voltages to the card and then _______________. A. test transistors or integrated circuits for gain and compare with manufacturer's specifications B. blow any accumulated dust from the card with at least 30 psi air from the ship's service air system C. pull the card, clean the sliding connections with a pencil eraser, and remove accumulated dust D. de-energize the card and check the printed circuit traces for continuity with an ohmmeter

Description : When troubleshooting a console circuit card suspected of being faulty, first check for proper voltages to the card and then _______________. A. test transistors or integrated circuits for gain and ... D. de-energize the card and check the printed circuit traces for continuity with an ohmmeter

Last Answer : Answer: C

A small gap is left at the joints of rails in a railway track to – (1) avoid the tracks being distorted due to seasonal temperature variation (2) avoid the heating of tracks to high temperature (3) control the speed of train (4) keep the rails equidistant

Description : A small gap is left at the joints of rails in a railway track to – (1) avoid the tracks being distorted due to seasonal temperature variation (2) avoid the heating of tracks to high temperature (3) control the speed of train (4) keep the rails equidistant

Last Answer : (1) avoid the tracks being distorted due to seasonal temperature variation Explanation: A small gap is left at the joints of rails in a railway track to provide space for the expansion of rail pieces when the temperature rises during summer.

A small gap is left at the joints of rails in a railway track to (1) avoid the tracks being distorted due to seasonal temperature variation (2) avoid the heating of tracks to high temperature (3) control the speed of train (4) keep the rails equidistant

Description : A small gap is left at the joints of rails in a railway track to (1) avoid the tracks being distorted due to seasonal temperature variation (2) avoid the heating of tracks to high temperature (3) control the speed of train (4) keep the rails equidistant

Last Answer : avoid the tracks being distorted due to seasonal temperature variation

A reverse-current relay will prevent AC generator motorization by ____________. A. automatically redirecting the load B. automatically speeding up the prime mover C. tripping the panel board main switch D. tripping the generator circuit breaker

Description : A reverse-current relay will prevent AC generator motorization by ____________. A. automatically redirecting the load B. automatically speeding up the prime mover C. tripping the panel board main switch D. tripping the generator circuit breaker

Last Answer : Answer: D

What type of service is NOT provided by the circuit shown in the illustration? EL-0094 A. Logging of engine order signals from the bridge. B. Printed record of alarms as they occur. C. Visual metering of temperature and pressure conditions. D. Periodic recording of pressure and temperature conditions.

Description : What type of service is NOT provided by the circuit shown in the illustration? EL-0094 A. Logging of engine order signals from the bridge. B. Printed record of alarms as they ... . Visual metering of temperature and pressure conditions. D. Periodic recording of pressure and temperature conditions.

Last Answer : Answer: A

In D.C. motor construction, the armature coils' ends are _______________. A. soldered to the commutator bar risers B. imbedded into core slots C. crimped together with brush pigtails D. spliced with the field windings

Description : In D.C. motor construction, the armature coils' ends are _______________. A. soldered to the commutator bar risers B. imbedded into core slots C. crimped together with brush pigtails D. spliced with the field windings

Last Answer : Answer: A

When soldering a printed circuit board component, you should be careful to prevent damage by _________. A. quickly heating the joints, using a high wattage iron B. using the soldering iron tip sparingly C. using only acid cord solder D. applying mechanical pressure to the joints being soldered

Please log in or register to add a comment.

Please log in or register to answer this question.

1 Answer

Answer :

Please log in or register to add a comment.

Related questions