Use of flux during soldering is done to (A) Increase fluidity of solder by lowering its melting temperature (B) Prevent oxide formation (C) Wash away surplus solder (D) Full up the joint gap

Use of flux during soldering is done to
(A) Increase fluidity of solder by lowering its melting temperature (B) Prevent oxide formation
(C) Wash away surplus solder
(D) Full up the joint gap
by

1 Answer

Answer :

(B) Prevent oxide formation
by

Related questions

Why is it a poor practice to use a high wattage soldering iron when soldering or desoldering components on a printed circuit board? A. The circuit board will blister and warp. B. The foil wire bonded to the board may come loosened from the board. C. The circuit board has a low melting temperature. D. The solder is kept to a dull heat dissipating finish.

Description : Why is it a poor practice to use a high wattage soldering iron when soldering or desoldering components on a printed circuit board? A. The circuit board will blister and warp. B. The foil wire bonded ... board has a low melting temperature. D. The solder is kept to a dull heat dissipating finish.

Last Answer : Answer: B

When troubleshooting an electronic circuit, a cold solder joint can be located with the aid of an ohmmeter. Once the problem has been located, you should _________________. A. reheat the circuit in an oven to an even temperature and recheck with an ohmmeter B. reheat the connection with a match and recheck with an ohmmeter C. reheat connection with a soldering tool and recheck with an ohmmeter D. do nothing as this is the normal condition

Description : When troubleshooting an electronic circuit, a cold solder joint can be located with the aid of an ohmmeter. Once the problem has been located, you should _________________. A. reheat the circuit in an ... a soldering tool and recheck with an ohmmeter D. do nothing as this is the normal condition

Last Answer : Answer: C

When soldering a printed circuit board component, you should be careful to prevent damage by _________. A. quickly heating the joints, using a high wattage iron B. using the soldering iron tip sparingly C. using only acid cord solder D. applying mechanical pressure to the joints being soldered

Description : When soldering a printed circuit board component, you should be careful to prevent damage by _________. A. quickly heating the joints, using a high wattage iron B. using the soldering iron tip sparingly C. using only acid cord solder D. applying mechanical pressure to the joints being soldered

Last Answer : Answer: B

The function of neutral flux used in the pyrometallurgy of metal extraction is to increase the __________ of the slag. (A) Fluidity (B) Basicity (C) Acidity (D) Viscosity

Description : The function of neutral flux used in the pyrometallurgy of metal extraction is to increase the __________ of the slag. (A) Fluidity (B) Basicity (C) Acidity (D) Viscosity

Last Answer : Option A

The function of neutral flux used in the pyrometallurgy of metal extraction is to increase the __________ of the slag. (A) Fluidity (B) Basicity (C) Acidity (D) Viscosity

Description : The function of neutral flux used in the pyrometallurgy of metal extraction is to increase the __________ of the slag. (A) Fluidity (B) Basicity (C) Acidity (D) Viscosity

Last Answer : Option A

Pick up the correct statement from the following: (A) Solder material is an alloy which melts at a temperature above 400°C (B) Brazing is done at temperature above 600°C to 1100°C (C) Brazing joint is stronger than the solder joint (D) All the above

Description : Pick up the correct statement from the following: (A) Solder material is an alloy which melts at a temperature above 400°C (B) Brazing is done at temperature above 600°C to 1100°C (C) Brazing joint is stronger than the solder joint (D) All the above

Last Answer : Answer: Option D

Presence of high phosphorous in cast iron increases its (A) Fluidity (B) Melting point (C) Shrinkage (D) Tensile strength

Description : Presence of high phosphorous in cast iron increases its (A) Fluidity (B) Melting point (C) Shrinkage (D) Tensile strength

Last Answer : (A) Fluidity

What is the type of solder that would be used in hard soldering?

Description : What is the type of solder that would be used in hard soldering?

Last Answer : Need answer

Why are small-wattage soldering irons not used to solder large conductors?

Description : Why are small-wattage soldering irons not used to solder large conductors?

Last Answer : Although its temperature is as high as the larger irons, it does not have thermal inertia.

How should excess solder be removed from a hot soldering iron?

Description : How should excess solder be removed from a hot soldering iron?

Last Answer : By use of a cleaning cloth.

Stainless steel is welded with difficulty because of (A) Its high melting temperature (B) Chances of cracking (C) Oxide film formation (D) Chromium carbide formation

Description : Stainless steel is welded with difficulty because of (A) Its high melting temperature (B) Chances of cracking (C) Oxide film formation (D) Chromium carbide formation

Last Answer : Option C

Oxide of sulphur present in the atmosphere are washed down by rains to cause – (1) Depletion of fossil fuel reserves (2) Eutrophication in lakes (3) Lowering of pH of soil (4) Industrial smog formation

Description : Oxide of sulphur present in the atmosphere are washed down by rains to cause – (1) Depletion of fossil fuel reserves (2) Eutrophication in lakes (3) Lowering of pH of soil (4) Industrial smog formation

Last Answer : (1) Depletion of fossil fuel reserves Explanation: The oxide of Sulphur (Sulphur Dioxide) is washed down on earth as acid rain.

Oxide of sulphur present in the atmosphere are washed down by rains to cause : (1) Depletion of fossil fuel reserves (2) Eutrophication in lakes (3) Lowering of pH of soil (4) Industrial smog formation

Description : Oxide of sulphur present in the atmosphere are washed down by rains to cause : (1) Depletion of fossil fuel reserves (2) Eutrophication in lakes (3) Lowering of pH of soil (4) Industrial smog formation

Last Answer : Depletion of fossil fuel reserves

Presence of high amount of silicon in cast iron (A) Suppresses the decomposition of Fe3C (B) Increases the formation of graphite (C) Increases the contraction of the metal (D) Reduces its fluidity

Description : Presence of high amount of silicon in cast iron (A) Suppresses the decomposition of Fe3C (B) Increases the formation of graphite (C) Increases the contraction of the metal (D) Reduces its fluidity

Last Answer : (B) Increases the formation of graphite

Addition of silicon to cast iron (A) Promotes graphite module formation (B) Improves its ductility (C) Does not promote graphite flakes formation (D) Increases the fluidity of molten metal

Description : Addition of silicon to cast iron (A) Promotes graphite module formation (B) Improves its ductility (C) Does not promote graphite flakes formation (D) Increases the fluidity of molten metal

Last Answer : Option D

Compare Brazing and Soldering on the basis of : (i) Temperature Used. (ii) Filler Material. (iii) Joint Strength (iv) Applications.

Description : Compare Brazing and Soldering on the basis of : (i) Temperature Used. (ii) Filler Material. (iii) Joint Strength (iv) Applications.

Last Answer : Comparison of Brazing and Soldering:

Glass pipes can be joined by (A) Flanges (B) Welding (C) Soldering (D) Bell and spigot joint

Description : Glass pipes can be joined by (A) Flanges (B) Welding (C) Soldering (D) Bell and spigot joint

Last Answer : (D) Bell and spigot joint

Out of the following, the joint produced by __________ has the lowest strength. (A) Soldering (B) Welding (C) Brazing (D) Riveting

Description : Out of the following, the joint produced by __________ has the lowest strength. (A) Soldering (B) Welding (C) Brazing (D) Riveting

Last Answer : (A) Soldering

The joint for soldering is supported by binding wire made of (A) Mild steel (B) Copper (C) Soft iron (D) Stainless steel

Description : The joint for soldering is supported by binding wire made of (A) Mild steel (B) Copper (C) Soft iron (D) Stainless steel

Last Answer : Option C

Acid soldering flux poisoning?

Description : Acid soldering flux poisoning?

Last Answer : DefinitionAcid soldering flux is a chemical used to clean and protect the area (joint) where two pieces of metal come together. Flux poisoning occurs when someone swallows this substance.This is for information only ... Network.Also reviewed by David Zieve, MD, MHA, Medical Director, A.D.A.M., Inc.

Which type of flux should be used when soldering electrical wire connections and electronic components? A. Silver flux B. Rosin flux C. Solid flux D. Acid flux

Description : Which type of flux should be used when soldering electrical wire connections and electronic components? A. Silver flux B. Rosin flux C. Solid flux D. Acid flux

Last Answer : Answer: B

What type of flux must be used in all electrical and electronic soldering?

Description : What type of flux must be used in all electrical and electronic soldering?

Last Answer : Noncorrosive, nonconductive rosin fluxes.

What purpose does flux serve in the soldering process?

Description : What purpose does flux serve in the soldering process?

Last Answer : It cleans the metal by removing the oxide layer and prevents further oxidation during the soldering

Flux aids in soldering by removing what from surfaces to be soldered?

Description : Flux aids in soldering by removing what from surfaces to be soldered?

Last Answer : Oxides.

What is the purpose of using flux at the time of soldering?

Description : What is the purpose of using flux at the time of soldering? A. To remove oxidation B. To prevent corrosion C. To promote wet surface D. All of these

Last Answer : What is the purpose of using flux at the time of soldering? A. To remove oxidation B. To prevent corrosion C. To promote wet surface D. All of these

Higher viscosity index of a lubricating oil denotes (A) Less changes in fluidity of oil with temperature (B) Substantially high change in fluidity of oil with temperature (C) Its unsuitability under varying temperature conditions (D) None of these

Description : Higher viscosity index of a lubricating oil denotes (A) Less changes in fluidity of oil with temperature (B) Substantially high change in fluidity of oil with temperature (C) Its unsuitability under varying temperature conditions (D) None of these

Last Answer : (A) Less changes in fluidity of oil with temperature

A capacitor discolored due to excessive heat should be _____________. A. calibrated using a capactance wheatstone bridge B. replaced and the reason for the overheating found C. cooled with a spray can of refrigerant approved for this purpose D. resoldered with care taken to insure that the origional cold solder joint is repaired

Description : A capacitor discolored due to excessive heat should be _____________. A. calibrated using a capactance wheatstone bridge B. replaced and the reason for the overheating found C. cooled with a spray ... purpose D. resoldered with care taken to insure that the origional cold solder joint is repaired

Last Answer : Answer: B

What causes a "fractured solder" joint?

Description : What causes a "fractured solder" joint?

Last Answer : Movement of the parts being soldered while the solder is cooling.

Which of the following is an undesirable property of slag produced during the Pyrometallurgical method of metal extraction from its ore? (A) High fusibility & fluidity (B) High thermal conductivity (C) Low density (D) High chemical activity

Description : Which of the following is an undesirable property of slag produced during the Pyrometallurgical method of metal extraction from its ore? (A) High fusibility & fluidity (B) High thermal conductivity (C) Low density (D) High chemical activity

Last Answer : B) High thermal conductivity

Nuclear fuel generally used in reactors is uranium oxide instead of uranium, because the former has higher (A) Melting point, hence can be subjected to higher temperature (B) Density; hence core volume for a given power output would be smaller (C) Resistance to effects of irradiation (D) All (A), (B) and (C)

Description : Nuclear fuel generally used in reactors is uranium oxide instead of uranium, because the former has higher (A) Melting point, hence can be subjected to higher temperature (B) Density; hence core volume for a given ... be smaller (C) Resistance to effects of irradiation (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

For the formation of metal oxide, `deltaG^(@)` __________ with increase in temperature.

Description : For the formation of metal oxide, `deltaG^(@)` __________ with increase in temperature.

Last Answer : For the formation of metal oxide, `deltaG^(@)` __________ with increase in temperature. A. Only I B. I,II only C. I,II,III only D. All

How do you prevent excessive heat buildup on an area of a board when soldering multilead components?

Description : How do you prevent excessive heat buildup on an area of a board when soldering multilead components?

Last Answer : Use a skipping pattern

The relay operating speed depends upon (a) the spring tension (b) the rate of flux built up (c) armature core air gap (d) all of the above

Description : The relay operating speed depends upon (a) the spring tension (b) the rate of flux built up (c) armature core air gap (d) all of the above

Last Answer : (d) all of the above

Water is normally used as a coolant in the heat exchange equipments mainly because of its (A) Abundance & high heat capacity (B) Low density (C) Low viscosity (D) High fluidity

Description : Water is normally used as a coolant in the heat exchange equipments mainly because of its (A) Abundance & high heat capacity (B) Low density (C) Low viscosity (D) High fluidity

Last Answer : (A) Abundance & high heat capacity

Pitch (a product of coal tar distillation) is always mixed with creosote oil, when it is to be burnt in a burner, because (A) Its calorific value is very less (B) Tar neutralises the residual acids present in pitch (C) It reduces viscosity and imparts fluidity for its transportation through pipelines at economic pressure drop (D) All (A), (B) and (C)

Description : Pitch (a product of coal tar distillation) is always mixed with creosote oil, when it is to be burnt in a burner, because (A) Its calorific value is very less (B) Tar neutralises the residual acids ... for its transportation through pipelines at economic pressure drop (D) All (A), (B) and (C)

Last Answer : (C) It reduces viscosity and imparts fluidity for its transportation through pipelines at economic pressure drop

What happens if the air gap flux density in an induction motor increases?

Description : What happens if the air gap flux density in an induction motor increases?

Last Answer : The increase in air gap flux increases iron loss and hence efficiency decreases.

In D.C. generators on no-load, the air gap flux distribution in space is?

Last Answer : In D.C. generators on no-load, the air gap flux distribution in space is flat topped.

The atmospheric temperature during melting of ice/snow (in the atmosphere) (A) Decreases (B) Increases (C) Remain same (D) May increase or decrease; depends on the altitude where snow melts Answer

Description : The atmospheric temperature during melting of ice/snow (in the atmosphere) (A) Decreases (B) Increases (C) Remain same (D) May increase or decrease; depends on the altitude where snow melts Answer

Last Answer : A) Decreases

Cast iron compared to steel is better in (A) Ductility (B) Fluidity & castability (C) Strength (D) Malleability

Description : Cast iron compared to steel is better in (A) Ductility (B) Fluidity & castability (C) Strength (D) Malleability

Last Answer : (B) Fluidity & castability

Lead is added to 60:40 brass primarily to improve (A) Machinability (B) Corrosion resistance (C) Fluidity (D) Strength

Description : Lead is added to 60:40 brass primarily to improve (A) Machinability (B) Corrosion resistance (C) Fluidity (D) Strength

Last Answer : (A) Machinability

Two 12 ft. sections of aluminum siding are placed end to end on the outside wall of house. How large a gap should be left between the pieces to prevent buckling if the temperature can change by 55˚C?  a. 0.21 m  b. 0.18 m  c. 0.31 in  d. 0.18 in

Description : Two 12 ft. sections of aluminum siding are placed end to end on the outside wall of house. How large a gap should be left between the pieces to prevent buckling if the temperature can change by 55˚C?  a. 0.21 m  b. 0.18 m  c. 0.31 in  d. 0.18 in

Last Answer : 0.18 in

Pick out the correct statement. (A) If an insoluble gas is passed through a volatile liquid placed in a perfectly insulated container, the temperature of the liquid will increase (B) A process is irreversible as long as Δ S for the system is greater than zero (C) The mechanical work done by a system is always equal to∫P.dV (D) The heat of formation of a compound is defined as the heat of reaction leading to the formation of the compound from its reactants

Description : Pick out the correct statement. (A) If an insoluble gas is passed through a volatile liquid placed in a perfectly insulated container, the temperature of the liquid will increase (B) A ... compound is defined as the heat of reaction leading to the formation of the compound from its reactants

Last Answer : (D) The heat of formation of a compound is defined as the heat of reaction leading to the formation of the compound from its reactants

Pick out the correct statement. (A) Like internal energy and enthalpy, the absolute value of standard entropy for elementary substances is zero (B) Melting of ice involves increase in enthalpy and a decrease in randomness (C) The internal energy of an ideal gas depends only on its pressure (D) Maximum work is done under reversible conditions

Description : Pick out the correct statement. (A) Like internal energy and enthalpy, the absolute value of standard entropy for elementary substances is zero (B) Melting of ice involves increase in enthalpy and ... of an ideal gas depends only on its pressure (D) Maximum work is done under reversible conditions

Last Answer : (D) Maximum work is done under reversible conditions

Pick up the correct statement from the following (A) The ratio of the up flux and down flux just above the snow surface, is called albedo (B) Spectral albedo of snow is calculated for the semi-infinite snow thickness (C) Water equivalent height of snow is the height of water column obtained by melting snow (D) All of these

Description : Pick up the correct statement from the following (A) The ratio of the up flux and down flux just above the snow surface, is called albedo (B) Spectral albedo of snow is calculated for the semi- ... equivalent height of snow is the height of water column obtained by melting snow (D) All of these

Last Answer : Answer: Option D

When charging lead-acid batteries, the charging rate should be reduced as the battery nears its full charge to ____________. A. prevent damaging battery plates B. allow equalization of cell voltages C. reduce lead sulfate deposits D. increase lead peroxide formation

Description : When charging lead-acid batteries, the charging rate should be reduced as the battery nears its full charge to ____________. A. prevent damaging battery plates B. allow equalization of cell voltages C. reduce lead sulfate deposits D. increase lead peroxide formation

Last Answer : Answer: A

When charging lead-acid batteries, you should reduce the charging rate as the battery nears its full charge capacity to ______________. A. prevent excessive gassing and overheating B. allow equalization of cell voltages C. reduce lead sulfate deposits D. increase lead peroxide formation

Description : When charging lead-acid batteries, you should reduce the charging rate as the battery nears its full charge capacity to ______________. A. prevent excessive gassing and overheating B. allow equalization of cell voltages C. reduce lead sulfate deposits D. increase lead peroxide formation

Last Answer : Answer: A

The C.O.P. of a refrigeration cycle with lowering of condenser temperature, keeping the evaporator temperatureconstant, will (a) increase (b) decrease (c) may increase or decrease depending on the type of refrigerant used (d) remain unaffected

Description : The C.O.P. of a refrigeration cycle with lowering of condenser temperature, keeping the evaporator temperatureconstant, will (a) increase (b) decrease (c) may increase or decrease depending on the type of refrigerant used (d) remain unaffected

Last Answer : Ans: a

Temperature attained in soldering of metals is about __________ °C. (A) 150-300 (B) 400-500 (C) 650-800 (D) 1000-1100

Description : Temperature attained in soldering of metals is about __________ °C. (A) 150-300 (B) 400-500 (C) 650-800 (D) 1000-1100

Last Answer : (A) 150-300

Why is soldering done ?

Description : Why is soldering done ?

Last Answer : Soldering is done to increase the strength and durability of electrical wiring joints and to ensure uninterrupted wiring and protection from corrosive processes due to unforeseen nature.

What should be done to a soldering iron tip that is pitted?

Description : What should be done to a soldering iron tip that is pitted?

Last Answer : File the tip until it is smooth and retin it.