If a small electric motor is imersed in salt water it should be _________. I. washed in fresh water II. dried in an oven A. I only B. II only C. both I and II D. neither I or II

If a small electric motor is imersed in salt water it should be _________. I. washed in fresh water II. dried in an oven A. I only B. II only C. both I and II  D. neither I or II
by

1 Answer

Answer :

Answer: C
by

Related questions

Surface preparation for Metallising the abrasives used for final cleaning is a) Chilled iron grit G.24, as defined in BS : 2451 b) Washed salt free angular silica sand of mesh size 12 to 30 with a minimum of 40% retained on a 20 mesh c) either (a) or (b) * d) d) neither (a) or (b)

Description : Surface preparation for Metallising the abrasives used for final cleaning is a) Chilled iron grit G.24, as defined in BS : 2451 b) Washed salt free angular silica sand of mesh size 12 to 30 with a minimum of 40% retained on a 20 mesh c) either (a) or (b) * d) d) neither (a) or (b)

Last Answer : c) either (a) or (b) *

If a small electric motor has been submerged in saltwater for a short period of time, you should _____________. A. send it ashore for rewinding B. rinse it with warm freshwater and bake it dry in an oven C. soak it in a bucket of commercial solvent and bake with internal heat D. clean it with carbon tetrachloride and blow it out with compressed air

Description : If a small electric motor has been submerged in saltwater for a short period of time, you should _____________. A. send it ashore for rewinding B. rinse it with warm freshwater and bake it dry ... and bake with internal heat D. clean it with carbon tetrachloride and blow it out with compressed air

Last Answer : Answer: B

Air gap readings should be taken on electrical generation machinery periodicly to _________. I. determine the need for cleaning II. check the condition of the bearings A. I only B. II only C. both I and II D. neither I or II

Description : Air gap readings should be taken on electrical generation machinery periodicly to _________. I. determine the need for cleaning II. check the condition of the bearings A. I only B. II only C. both I and II D. neither I or II

Last Answer : Answer: B

smelly towels after washed and dried

Description : smelly towels after washed and dried

Last Answer : To keep towels from molding make sure that you dry the towels right after you wash them.

What is the best way to remove grease stains, both fresh and washed-in?

Description : What is the best way to remove grease stains, both fresh and washed-in?

Last Answer : I rub Dawn dish detergent on it with some cool water and scrub lightly with a toothbrush I dedicate to this type of chore, then wash in cold water and hang dry. If the stain is gone, then I rewash the garment as usual.

Some large A.C. motors are equipped with with heaters. These could be ___________. I. resistance heaters bolted directly to the frame II. low voltage windings embedded in the motor windings A. I only B. II only C. either I or II D. neither I or II

Description : Some large A.C. motors are equipped with with heaters. These could be ___________. I. resistance heaters bolted directly to the frame II. low voltage windings embedded in the motor windings A. I only B. II only C. either I or II D. neither I or II

Last Answer : Answer: C

To repair a small electrical motor that has been submerged in saltwater, you should _____________. A. wash it with fresh water and apply an external source of heat B. renew the windings C. send it ashore to an approved service facility D. rinse all electrical parts with a carbon tetrachloride cleaning solvent and then blow dry the motor with compressed air

Description : To repair a small electrical motor that has been submerged in saltwater, you should _____________. A. wash it with fresh water and apply an external source of heat B. renew the windings ... electrical parts with a carbon tetrachloride cleaning solvent and then blow dry the motor with compressed air

Last Answer : Answer: A

Moisture absorbed in the windings or condensed on the surface of electrical machinery insulation ________. A. is good for long term preserving since most insulation is organic and contains some amount B. lowers the insulation value and is a common cause of fault grounds in idle machines C. will enhance insulation resistance only if it is fresh water and contains no salt D. reduces the amount of current supplied or drawn by the machine so horsepower is limited

Description : Moisture absorbed in the windings or condensed on the surface of electrical machinery insulation ________. A. is good for long term preserving since most insulation is organic and contains some amount B. ... D. reduces the amount of current supplied or drawn by the machine so horsepower is limited

Last Answer : Answer: B

The electrician reports to you that he has obtained low (but above 1 megohm) megger readings on the windings of a deck winch motor. Upon checking the records of that motor, you find the readings have consistently been at that level for the last six yea A. motor be replaced B. windings be dried C. windings be cleaned D. readings are acceptable

Description : The electrician reports to you that he has obtained low (but above 1 megohm) megger readings on the windings of a deck winch motor. Upon checking the records of that motor, you find the readings have ... yea A. motor be replaced B. windings be dried C. windings be cleaned D. readings are acceptable

Last Answer : Answer: D

The total weight of a pycnometer with water and oven dried soil 20 (g) is 1600 g. The pycnometer filled with water alone weighs 1500 g. The specific gravity of the soil, is (A) 1.0 (B) 1.5 (C) 2.0 (D) 2.5

Description : The total weight of a pycnometer with water and oven dried soil 20 (g) is 1600 g. The pycnometer filled with water alone weighs 1500 g. The specific gravity of the soil, is (A) 1.0 (B) 1.5 (C) 2.0 (D) 2.5

Last Answer : (C) 2.0

Pick up the correct statement from the following: (A) Blistering may be cured by applying water paint finished with oil paint dried with a little copal varnish (B) Cracked paints may be cured by removing paint and giving a fresh coat of paint (C) Crawling paints may be cured by sand preparing the surface and giving a fresh coat with plenty of turps (D) All the above

Description : Pick up the correct statement from the following: (A) Blistering may be cured by applying water paint finished with oil paint dried with a little copal varnish (B) Cracked paints may be cured by ... sand preparing the surface and giving a fresh coat with plenty of turps (D) All the above

Last Answer : Answer: Option D

Fresh grapes contains 80% of water by weight, where as dry grapes contains 50% of water by weight. Yamini buys 100kg of fresh grapes for a total price of Rs. 300. At what price should she sell the dry grapes (fresh grapes are dried up) to earn 80%profit?

Description : Fresh grapes contains 80% of water by weight, where as dry grapes contains 50% of water by weight. Yamini buys 100kg of fresh grapes for a total price of Rs. 300. At what price should she sell the dry grapes (fresh grapes are dried up) to earn 80%profit?

Last Answer :  In fresh grapes ratio of water to grapes is 80:20= 4:1 In dry grapes ratio is = 50:50 =1:1 Weight of grapes is = 100*[1/5]= 20kg Weight of dry grapes = 20*2 =40 kg Required amount is = 300*100[180/100]/40 = Rs. 1350

Can I make dried basil simply by letting fresh basil dry on my countertop?

Description : Can I make dried basil simply by letting fresh basil dry on my countertop?

Last Answer : To dry fresh herbs, it is usually best to hang them up in order to dry them as quickly as possible. Just tie a bunch together at the stems with some twine and hang upside down in an area with ... with leaving them on the counter is that they won't get sufficient air flow, which may cause molding.

Can I grow jalapeno peppers from fresh seeds, not dried?

Description : Can I grow jalapeno peppers from fresh seeds, not dried?

Last Answer : I’ll say yes. In nature, the seeds are “planted” in the decaying pepper without being dried first.

How can the glycemic index for dried apricots be less than for fresh ones?

Description : How can the glycemic index for dried apricots be less than for fresh ones?

Last Answer : It sounds like you just accidentally came up with a neat kids school science project. As far as the fruit goes, there’s got to be some sort of chemical breakdown that would explain it. It’s interesting though, I’ll give you that.

can fresh cilantro be dried ?

Description : can fresh cilantro be dried ?

Last Answer : Need Answer

Air gap readings for electrical generating equipment should be taken periodicly. This is to _______. I. determine the condition of the bearings II. prevent damage to the rotor and stator A. I only B. II only C. both I and II D. neither I or II

Description : Air gap readings for electrical generating equipment should be taken periodicly. This is to _______. I. determine the condition of the bearings II. prevent damage to the rotor and stator A. I only B. II only C. both I and II D. neither I or II

Last Answer : Answer: C

Air gap readings should be taken on electrical generation equipment periodicly to ________. I. check machine effeciency II. determine the need for cleaning A. I only B. II only C. both I and II D. neither I or II

Description : Air gap readings should be taken on electrical generation equipment periodicly to ________. I. check machine effeciency II. determine the need for cleaning A. I only B. II only C. both I and II D. neither I or II

Last Answer : Answer: D

Which way does electron current flow in the illustrated device? I. A to B II. B to A EL-0079 A. I only B. II only C. both I and II D. neither I or II

Description : Which way does electron current flow in the illustrated device? I. A to B II. B to A EL-0079 A. I only B. II only C. both I and II D. neither I or II

Last Answer : Answer: A

In an A.C. generator, pitting of collector rings will cause __________. I. sparking II. Chattering A. I only B. II only C. both I and II D. neither I or II

Description : In an A.C. generator, pitting of collector rings will cause __________. I. sparking II. Chattering A. I only B. II only C. both I and II D. neither I or II

Last Answer : Answer: D

Which of the illustrated lamps would be brighter? I. X II. Y EL-0008 A. I only B. II only C. Both I and II would be equally bright D. Neither would be lit

Description : Which of the illustrated lamps would be brighter? I. X II. Y EL-0008 A. I only B. II only C. Both I and II would be equally bright D. Neither would be lit

Last Answer : Answer: A

What type of electric motor is commonly used to start small auxiliary diesel engines? A. synchronous B. series C. shunt D. cage

Description : What type of electric motor is commonly used to start small auxiliary diesel engines? A. synchronous B. series C. shunt D. cage

Last Answer : Answer: B

In case of a universal motor, torque pulsation is minimized by _________. (A) load inertia (B) rotor inertia (C) both rotor and load inertia (D) none of the above

Description : In case of a universal motor, torque pulsation is minimized by _________. (A) load inertia (B) rotor inertia (C) both rotor and load inertia (D) none of the above

Last Answer : Ans: C In a universal motor, torque pulsation is minimized by rotor and load inertia.

Why are salt and sugar used in the production of dried meat and dried fruits ?

Description : Why are salt and sugar used in the production of dried meat and dried fruits ?

Last Answer : Substances that maintain highly hypertonic environment, like sugar and salt, are used in the production of dried meat, fish or fruits (for example, cod) because the material to be conserved is then ... the growth of populations of decomposer beings (since these beings also lose water and die).

Which is a regenerative furnace? (A) Coke oven heating chamber (B) Open hearth furnace (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Which is a regenerative furnace? (A) Coke oven heating chamber (B) Open hearth furnace (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

In a furnace operation, which is not preheated? (A) Solid fuels (B) Hydrocarbon containing fuel gases (e.g. coke oven gas, refinery gas etc.) (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : In a furnace operation, which is not preheated? (A) Solid fuels (B) Hydrocarbon containing fuel gases (e.g. coke oven gas, refinery gas etc.) (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Prime coking coal is always blended with medium or non- coking coal before carbonisation (A) To check against its excessive swelling during heating, which may exert high pressure and damage coke oven walls (B) Because, it alone produces unreactive coke (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Prime coking coal is always blended with medium or non- coking coal before carbonisation (A) To check against its excessive swelling during heating, which may exert high pressure and damage coke oven walls (B) Because, it alone produces unreactive coke (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Coke oven gas produced by high temperature carbonisation of coal (as compared to that produced by low temperature carbonisation), has (A) Higher calorific value (B) Lower hydrogen content (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Coke oven gas produced by high temperature carbonisation of coal (as compared to that produced by low temperature carbonisation), has (A) Higher calorific value (B) Lower hydrogen content (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (D) Neither (A) nor (B)

In order to change the direction of rotation of a D.C. motor_________. I. the field leads must be changed II. the input leads must be changed A. I only B. II only C. either I or II D. neither I or II

Description : In order to change the direction of rotation of a D.C. motor_________. I. the field leads must be changed II. the input leads must be changed A. I only B. II only C. either I or II D. neither I or II

Last Answer : Answer: A

If deck machinery is expected to be idle for an extended period of time you should____________. A. have electrical safety gloves available in case of electrical shock before running B. perform a 'high pot' test to determine the condition of the insulation C. water wash the motor and controller to remove any salt that may interfere with smooth operation D. check run at regular intervals to inusre correct operation and to renew the internal coating of lubrication

Description : If deck machinery is expected to be idle for an extended period of time you should____________. A. have electrical safety gloves available in case of electrical shock before running B. perform ... run at regular intervals to inusre correct operation and to renew the internal coating of lubrication

Last Answer : Answer: D

The direction of rotation of hysteresis motor is reversed by (A) Shift shaded pole with respect to main pole (B) Reversing supply lead (C) Either A or B (D) Neither A nor B

Description : The direction of rotation of hysteresis motor is reversed by (A) Shift shaded pole with respect to main pole (B) Reversing supply lead (C) Either A or B (D) Neither A nor B

Last Answer : Ans: A This motor used single phase, 50Hz supply and stator has two windings. These are connected continuously from starting to running.

What are some species of salt-water, fresh-water, and both-water fish?

Description : What are some species of salt-water, fresh-water, and both-water fish?

Last Answer : The only one I can think of is Salmon, hatches in freshwater, lives its life in saltwater, then returns to freshwater to drop off its eggs. But it dies shortly thereafter.

The migratory fish that live in both fresh and salt water, independent of breeding is called as? a. Catadromous fish b. Potamodromous fish c. Amphidromous fish d. Anadromous fish e. None

Description : The migratory fish that live in both fresh and salt water, independent of breeding is called as? a. Catadromous fish b. Potamodromous fish c. Amphidromous fish d. Anadromous fish e. None

Last Answer : c. Amphidromous fish

In the illustrated test, if the lamp fails to light on any of the three windings then _________. EL-0027 A. all three windings are grounded and the motor should be sent out for repair B. the brushes should be set back on the commutator and the test redone C. the ground is not in the windings and the connections to the motor controller and the controller should be checked D. the test should be redone at a higher voltage

Description : In the illustrated test, if the lamp fails to light on any of the three windings then _________. EL-0027 A. all three windings are grounded and the motor should be sent out for repair B. ... the motor controller and the controller should be checked D. the test should be redone at a higher voltage

Last Answer : Answer: C

D.C. motor brush adjustment includes attention to _________. A. angle with the commutator and clearance within the holder B. brush length and pigtail tightness C. grade of material and surface dirt conditions D. all of the above

Description : D.C. motor brush adjustment includes attention to _________. A. angle with the commutator and clearance within the holder B. brush length and pigtail tightness C. grade of material and surface dirt conditions D. all of the above

Last Answer : Answer: D

In the illustrated device, the part labeled '1A' _________. EL-0001 A. are start and run windings for a single phase shaded pole induction motor B. is the stator for a polyphase induction motor C. is the armature for a squirrel cage rotor motor D. are direct current shunt field windings for a universal motor

Description : In the illustrated device, the part labeled '1A' _________. EL-0001 A. are start and run windings for a single phase shaded pole induction motor B. is the stator for a polyphase induction ... armature for a squirrel cage rotor motor D. are direct current shunt field windings for a universal motor

Last Answer : Answer: B

The motor starts when the start button in the illustration is pushed, but stops when the button is released the trouble is _________. EL-0007 A. the incorrect thermal overload coil B. a faulty 'M' coil C. a dirty contact on the Disc.Sw. at 'L3' D. a faulty holding relay contact

Description : The motor starts when the start button in the illustration is pushed, but stops when the button is released the trouble is _________. EL-0007 A. the incorrect thermal overload coil B. a faulty 'M' coil C. a dirty contact on the Disc.Sw. at 'L3' D. a faulty holding relay contact

Last Answer : Answer: D

If a unloaded shunt motor's field were weakened by rheostat resistance or by an open circuit, the motor would _________. A. overspeed due to reduced CEMF B. stop because of low flux C. continue to run at base speed D. slow down and overheat

Description : If a unloaded shunt motor's field were weakened by rheostat resistance or by an open circuit, the motor would _________. A. overspeed due to reduced CEMF B. stop because of low flux C. continue to run at base speed D. slow down and overheat

Last Answer : Answer: A

The devices located at coordinates '49W' in the illustration represents a/an _________. EL-0100 A. A.C. motor B. A.C. relay coil C. D.C. motor D. D.C. buzzer

Description : The devices located at coordinates '49W' in the illustration represents a/an _________. EL-0100 A. A.C. motor B. A.C. relay coil C. D.C. motor D. D.C. buzzer

Last Answer : Answer: B

As load is added to a shunt motor, the motor will _________. A. speed up B. continue to operate at the same speed C. slow down slightly D. stop

Description : As load is added to a shunt motor, the motor will _________. A. speed up B. continue to operate at the same speed C. slow down slightly D. stop

Last Answer : Answer: C

The counter EMF of a DC motor is maximum when the _________. A. motor is at rated speed B. armature is not turning C. motor is almost up to rated speed D. armature has just begun to turn

Description : The counter EMF of a DC motor is maximum when the _________. A. motor is at rated speed B. armature is not turning C. motor is almost up to rated speed D. armature has just begun to turn

Last Answer : Answer: A

The rotor slots of a repulsion-type motor are generally skewed (placed nonparallel to the rotor axis) to _________. A. produce a constant starting torque B. permit a greater air gap with the starter C. permit a smaller air gap with the starter D. reduce eddy current losses

Description : The rotor slots of a repulsion-type motor are generally skewed (placed nonparallel to the rotor axis) to _________. A. produce a constant starting torque B. permit a greater air gap with the starter C. permit a smaller air gap with the starter D. reduce eddy current losses

Last Answer : Answer: A

The diagram shown in the illustration represents a _________. EL-0058 A. dual speed, 2-winding motor controller B. navigation running light circuit C. single phase, 2-motor selectable starter D. common fluorescent lighting circuit

Description : The diagram shown in the illustration represents a _________. EL-0058 A. dual speed, 2-winding motor controller B. navigation running light circuit C. single phase, 2-motor selectable starter D. common fluorescent lighting circuit

Last Answer : Answer: B

The synchronous speed for a 3 phase 6-pole induction motor is 1200 rpm. If the number of poles is now reduced to 4 with the frequency remaining constant, the rotor speed with a slip of 5% will be _________. (A) 1690 rpm (B) 1750 rpm (C) 1500 rpm (D) 1710 rpm

Description : The synchronous speed for a 3 phase 6-pole induction motor is 1200 rpm. If the number of poles is now reduced to 4 with the frequency remaining constant, the rotor speed with a slip of 5% will be _________. (A) 1690 rpm (B) 1750 rpm (C) 1500 rpm (D) 1710 rpm

Last Answer : (D) 1710 rpm

When the control handle is in the 'off' position, the solenoid actuated brake of the electric winch is _________. A. de-energized and the brake is released B. energized and the brake is released C. energized and the brake is set by a spring D. de-energized and the brake is set by a spring

Description : When the control handle is in the 'off' position, the solenoid actuated brake of the electric winch is _________. A. de-energized and the brake is released B. energized and the brake is released C. energized and the brake is set by a spring D. de-energized and the brake is set by a spring

Last Answer : Answer: D

In a diesel electric plant, raising the generator's field excitation will cause the DC propulsion motor to ________. A. increase in speed B. decrease in speed C. affect generator speed only D. affect main motor speed if done in conjunction with higher generator engine speeds

Description : In a diesel electric plant, raising the generator's field excitation will cause the DC propulsion motor to ________. A. increase in speed B. decrease in speed C. affect generator speed only D. affect main motor speed if done in conjunction with higher generator engine speeds

Last Answer : Answer: A

On some diesel-electric ships, the DC propulsion motor will only attain half speed when the generator fields are fully excited. Speeds above this are obtained by _____________. A. rotating brush alignment B. raising the generator engine speed C. lowering the generator engine speed D. decreasing excitation

Description : On some diesel-electric ships, the DC propulsion motor will only attain half speed when the generator fields are fully excited. Speeds above this are obtained by _____________. A. rotating brush ... B. raising the generator engine speed C. lowering the generator engine speed D. decreasing excitation

Last Answer : Answer: B

_________ does not provide reliable end to end communication. a. TCP b. UDPc. Both TCP and UDP d. Neither TCP nor UDP

Description : _________ does not provide reliable end to end communication. a. TCP b. UDP c. Both TCP and UDP d. Neither TCP nor UDP

Last Answer : b. UDP