Which of the following is/are true concerning electric power operated watertight door systems? A. Each motor driven door must use the main bus as its source of power. B. Each distribution panel for the system must be on the lowest level where berthing quarters are located. C. Distribution panels must not be provided with a means of locking in order to permit quick activation of the system. D. Each system must have a separate branch circuit.

Which of the following is/are true concerning electric power operated watertight door systems? A. Each motor driven door must use the main bus as its source of power. B. Each distribution panel for the system must be on the lowest level where berthing quarters are located. C. Distribution panels must not be provided with a means of locking in order to permit quick activation of the system. D. Each system must have a separate branch circuit.
by

1 Answer

Answer :

Answer: D
by

Related questions

According to Coast Guard Regulations (46 CFR), which of the following systems must be arranged so as to be energized by the final emergency power source? A. at least one light in the steering gear room B. each power operated watertight door system C. each charging panel for temporary emergency batteries D. all of the above

Description : According to Coast Guard Regulations (46 CFR), which of the following systems must be arranged so as to be energized by the final emergency power source? A. at least one light in the ... operated watertight door system C. each charging panel for temporary emergency batteries D. all of the above

Last Answer : Answer: D

Which of the following statements concerning electrical cables is correct? A. Where they pass through watertight bulkheads, they should be fitted with watertight stuffing boxes. B. Electric cable coverings should never be grounded. C. Electrical cables must be rigidly held in place by welding of armored cable, or glued in place where nonmetallic insulation is used. D. All of the above.

Description : Which of the following statements concerning electrical cables is correct? A. Where they pass through watertight bulkheads, they should be fitted with watertight stuffing boxes. B. Electric cable coverings should ... , or glued in place where nonmetallic insulation is used. D. All of the above.

Last Answer : Answer: A

The part of the shipboard electrical system used to control the distribution of power to the branch circuits, is the _____________. A. bridge control panel B. disconnect links C. governor relay box D. main switchboard

Description : The part of the shipboard electrical system used to control the distribution of power to the branch circuits, is the _____________. A. bridge control panel B. disconnect links C. governor relay box D. main switchboard

Last Answer : Answer: D

In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, Federal Regulations (46 CFR) require the maximum fuse rating for that branch to be _________. EL-0013 A. 80% of the connected load B. 15 amps C. 20 amps D. 30 amps

Description : In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, Federal Regulations (46 CFR) require the maximum fuse rating for that branch to be _________. EL-0013 A. 80% of the connected load B. 15 amps C. 20 amps D. 30 amps

Last Answer : Answer: C

In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, 46 CFR requires the maximum fuse rating for that branch to be _________. EL-0013 A. 15 amps B. 80% of the connected load C. 20 amps D. 30 amps

Description : In the illustration if BRANCH NO. 1 is a lighting circuit for crew's berthing, 46 CFR requires the maximum fuse rating for that branch to be _________. EL-0013 A. 15 amps B. 80% of the connected load C. 20 amps D. 30 amps

Last Answer : Answer: C

According to U. S. Coast Guard Regulations (46 CFR), the motor controller for a submersible electric motor driven bilge pump should be installed _____________. A. in the shaft alley B. at the submersible bilge pump C. above the uppermost continuous deck D. at the engine room emergency control panel

Description : According to U. S. Coast Guard Regulations (46 CFR), the motor controller for a submersible electric motor driven bilge pump should be installed _____________. A. in the shaft alley B. at the submersible bilge pump C. above the uppermost continuous deck D. at the engine room emergency control panel

Last Answer : Answer: C

All electric cables passing through watertight bulkheads must be _____________. A. installed with watertight stuffing tubes B. grounded on both sides of the bulkhead C. fitted with unions on each side of the bulkhead D. welded on both sides of the bulkhead

Description : All electric cables passing through watertight bulkheads must be _____________. A. installed with watertight stuffing tubes B. grounded on both sides of the bulkhead C. fitted with unions on each side of the bulkhead D. welded on both sides of the bulkhead

Last Answer : Answer: A

Which of the following statements is true concerning all three-phase alternators? A. Each has three separate but identical armature windings acted on by one system of rotating magnets. B. Each has one armature winding acted on by three identical but separate systems of rotating magnets. C. All three-phase alternators are designed to operate with a 0.8 leading power factor. D. The three phases always provide power to the load through three sets of slip rings and brushes.

Description : Which of the following statements is true concerning all three-phase alternators? A. Each has three separate but identical armature windings acted on by one system of rotating magnets. B. Each has one ... The three phases always provide power to the load through three sets of slip rings and brushes.

Last Answer : Answer: A

The purpose of the automatic bus transfer shown in the illustration is to ___________. EL-0014 A. stepdown voltage to the lighting distribution panel B. provide emergency power to the lighting distribution panel C. energize the emergency switchboard from the main switchboard D. provide overcurrent protection to the lighting distribution panel

Description : The purpose of the automatic bus transfer shown in the illustration is to ___________. EL-0014 A. stepdown voltage to the lighting distribution panel B. provide emergency power to ... emergency switchboard from the main switchboard D. provide overcurrent protection to the lighting distribution panel

Last Answer : Answer: B

The heaters for the winch circuit shown in the illustration are powered from _____________. EL-0102 A. a separate source B. the winch main bus C. the master switch power circuit D. the contactor control circuit

Description : The heaters for the winch circuit shown in the illustration are powered from _____________. EL-0102 A. a separate source B. the winch main bus C. the master switch power circuit D. the contactor control circuit

Last Answer : Answer: A

A ground is indicated by the ground-detecting system on the main electrical switchboard. The FIRST step in locating the actual ground is to _____________. A. close all circuit breakers in the distribution panel until the ground detector indicates normal B. open the individual circuit breakers, one by one until the ground detection system indicates normal C. change over generators D. check each circuit with a megohmmeter

Description : A ground is indicated by the ground-detecting system on the main electrical switchboard. The FIRST step in locating the actual ground is to _____________. A. close all circuit breakers in ... ground detection system indicates normal C. change over generators D. check each circuit with a megohmmeter

Last Answer : Answer: B

Which of the following electric motors would be the safest and most reliable to use on the main deck of a vessel in foul weather conditions? A. Sealed motors B. Drip proof motors C. Enclosed motors D. Watertight motors

Description : Which of the following electric motors would be the safest and most reliable to use on the main deck of a vessel in foul weather conditions? A. Sealed motors B. Drip proof motors C. Enclosed motors D. Watertight motors

Last Answer : Answer: D

The purpose of the reverse power relay, provided on a ship's service alternator panel, is to trip the circuit in the event of ______________. A. main circuit overload B. high power transfer C. generator overspeeding D. alternator motorization

Description : The purpose of the reverse power relay, provided on a ship's service alternator panel, is to trip the circuit in the event of ______________. A. main circuit overload B. high power transfer C. generator overspeeding D. alternator motorization

Last Answer : Answer: D

A ground in an electrical circuit outside the engine room _____________. A. cannot be detected under normal conditions B. is of no consequence to engineering personnel C. is indicated at the branch circuit breaker panel D. is indicated by the ground detecting lamps on the main switchboard

Description : A ground in an electrical circuit outside the engine room _____________. A. cannot be detected under normal conditions B. is of no consequence to engineering personnel C. is indicated at the branch circuit breaker panel D. is indicated by the ground detecting lamps on the main switchboard

Last Answer : Answer: D

When using a megohmmeter to determine which shunt field coil is grounded in a DC machine, you must ____________. A. insulate the field frame from the ship's hull B. disconnect each shunt field coil before testing C. use a motor driven high capacity megohmmeter D. remove all main line lead connections before testing

Description : When using a megohmmeter to determine which shunt field coil is grounded in a DC machine, you must ____________. A. insulate the field frame from the ship's hull B. disconnect each shunt ... C. use a motor driven high capacity megohmmeter D. remove all main line lead connections before testing

Last Answer : Answer: B

Peripheral components for the operation of the astern valve position amplifier circuit shown in the illustration are _____________. EL-0099 A. resistors B. operated on +28 volts D.C. C. located on a separate circuit card D. all of the above

Description : Peripheral components for the operation of the astern valve position amplifier circuit shown in the illustration are _____________. EL-0099 A. resistors B. operated on +28 volts D.C. C. located on a separate circuit card D. all of the above

Last Answer : Answer: C

The timer element found in a reverse power relay obtains its operating torque via _____________. A. line voltage B. the main bus C. electromagnets D. a separate battery source

Description : The timer element found in a reverse power relay obtains its operating torque via _____________. A. line voltage B. the main bus C. electromagnets D. a separate battery source

Last Answer : Answer: C

The operating torque of the upper induction disc-type element, or timer element, of an AC reverse power relay is obtained from ____________. A. the main bus B. a separate battery source C. line voltage D. electromagnets

Description : The operating torque of the upper induction disc-type element, or timer element, of an AC reverse power relay is obtained from ____________. A. the main bus B. a separate battery source C. line voltage D. electromagnets

Last Answer : Answer: D

Motor controllers are seldom troubled with grounds because _____________. A. the auxiliary contacts have a high resistance connection B. the contactors and relays are mounted on a nonconducting panel C. the resistor banks are composed of individual series-connected units D. there are separate switches for the motor and the control

Description : Motor controllers are seldom troubled with grounds because _____________. A. the auxiliary contacts have a high resistance connection B. the contactors and relays are mounted on a nonconducting panel ... individual series-connected units D. there are separate switches for the motor and the control

Last Answer : Answer: B

When electrical cables penetrate watertight bulkheads, _______________. A. they should be grounded on either side of the bulkhead B. they must be bent to a radius of six diameters C. a watertight stuffing tube capable of accepting packing should be employed D. they should be secured by a clamp

Description : When electrical cables penetrate watertight bulkheads, _______________. A. they should be grounded on either side of the bulkhead B. they must be bent to a radius of six diameters C. a watertight stuffing tube capable of accepting packing should be employed D. they should be secured by a clamp

Last Answer : Answer: C

The purpose of a short circuit forcing module (short time trip) installed in a branch line is to provide ____________. A. high speed clearance of low impedance short circuits in the branch B. continuity of service on main bus under short circuit conditions in a branch C. isolation of short circuits by selective tripping of branch circuit breakers D. all of the above

Description : The purpose of a short circuit forcing module (short time trip) installed in a branch line is to provide ____________. A. high speed clearance of low impedance short circuits in the branch B. ... C. isolation of short circuits by selective tripping of branch circuit breakers D. all of the above

Last Answer : Answer: D

Time delayed or delayed action-type fuses are designed to _____________. A. prevent grounds in branch circuits B. prevent opens in motor circuits C. permit momentary overloads without melting D. guard lighting and electronic circuits

Description : Time delayed or delayed action-type fuses are designed to _____________. A. prevent grounds in branch circuits B. prevent opens in motor circuits C. permit momentary overloads without melting D. guard lighting and electronic circuits

Last Answer : Answer: C

Which of the following statements is true concerning the motor controller diagram shown in the illustration? EL-0023 A. Terminal 'T2' is hot only on high speed. B. Both indicating lights will be lit on both high and low speeds as they are connected to the common lead when the motor is running. C. Overload protection is provided for high speed operation only. D. 'L2' is always connected to 'T2' whenever the motor is running.

Description : Which of the following statements is true concerning the motor controller diagram shown in the illustration? EL-0023 A. Terminal 'T2' is hot only on high speed. B. Both indicating lights will be lit on ... high speed operation only. D. 'L2' is always connected to 'T2' whenever the motor is running.

Last Answer : Answer: D

The simplest method of controlling the terminal voltage of compound-wound DC generator is with a _____________. A. hand-operated field rheostat connected in series with the shunt field circuit B. separate exciter in a series with the shunt field C. carbon pile regulator in series with the load D. balance coil diverting neutral current through the shunt field

Description : The simplest method of controlling the terminal voltage of compound-wound DC generator is with a _____________. A. hand-operated field rheostat connected in series with the shunt field circuit B. ... in series with the load D. balance coil diverting neutral current through the shunt field

Last Answer : Answer: A

In a three-phase electrical system, three ground detecting lamps are provided. If all three lamps REMAIN at half-brilliance when the ground detecting test switch is operated, ______________. A. there is a slight ground on all three phases B. the switch must be replaced C. there are no grounds present D. the light bulbs are of improper voltage

Description : In a three-phase electrical system, three ground detecting lamps are provided. If all three lamps REMAIN at half-brilliance when the ground detecting test switch is operated, ______________. A. there is a ... must be replaced C. there are no grounds present D. the light bulbs are of improper voltage

Last Answer : Answer: C

A shore power circuit breaker should be closed only _____________. A. when the ship's generators have been directly paralleled to those on shore B. in a shipyard C. if a quick disconnect coupling is used D. when the ship's generators have been removed from the bus

Description : A shore power circuit breaker should be closed only _____________. A. when the ship's generators have been directly paralleled to those on shore B. in a shipyard C. if a quick disconnect coupling is used D. when the ship's generators have been removed from the bus

Last Answer : Answer: D

Transformers are used onboard ships with AC generators to _____________. A. change frequency B. increase power output to modulating frequency controllers C. decrease power output to modulating frequency controllers D. permit higher voltage for electric motor operation and low voltage for lighting circuits

Description : Transformers are used onboard ships with AC generators to _____________. A. change frequency B. increase power output to modulating frequency controllers C. decrease power output to modulating frequency ... D. permit higher voltage for electric motor operation and low voltage for lighting circuits

Last Answer : Answer: D

To remove an alternator operating in parallel with another unit from the main electrical bus, you must FIRST _________. A. adjust the power factor on both units B. set the desired voltage on the outgoing alternator C. open the circuit breaker on the outgoing alternator D. remove the load from the outgoing alternator

Description : To remove an alternator operating in parallel with another unit from the main electrical bus, you must FIRST _________. A. adjust the power factor on both units B. set the desired voltage on ... C. open the circuit breaker on the outgoing alternator D. remove the load from the outgoing alternator

Last Answer : Answer: D

In order to safely carry out repairs to a generator circuit breaker, it must be isolated from the bus. This is accomplished by opening the _____________. A. reverse power relay B. bus disconnect link C. generator bus fuse connections D. power directional relay

Description : In order to safely carry out repairs to a generator circuit breaker, it must be isolated from the bus. This is accomplished by opening the _____________. A. reverse power relay B. bus disconnect link C. generator bus fuse connections D. power directional relay

Last Answer : Answer: B

The complement system consists of a series of serum proteins that exist in a quiescent or very low-level state of activation in the uninfected host. Which of the following statement(s) is/are true concerning complement activation? a. The alternate (properdin) pathway of complement activation can occur directly through contact with fungal or bacterial cell wall compounds b. Complement component fragments may serve to decrease vascular permeability c. Excessive complement activation can produce deleterious effects d. Fragments of certain complement components serve as chemoattractants to additional cellular components of the host defense mechanism

Description : The complement system consists of a series of serum proteins that exist in a quiescent or very low-level state of activation in the uninfected host. Which of the following ... certain complement components serve as chemoattractants to additional cellular components of the host defense mechanism

Last Answer : Answer: a, c, d Complement activation can occur through either classic or alternate (properdin) pathways, both of which eventuate in deposition of terminal complement pathway components on the ... and release of lysosomal enzymes that can directly damage certain target tissues, such as the lung

What power would be consumed in EACH of the branch resistors of the circuit shown in the illustration if the source is 30 volts, the resistance for R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts

Description : What power would be consumed in EACH of the branch resistors of the circuit shown in the illustration if the source is 30 volts, the resistance for R1 is 10 ohms, R2 is 10 ohms and R3 is 10 ohms? EL-0032 A. 5 watts B. 10 watts C. 20 watts D. 40 watts

Last Answer : Answer: B

A dock: (A) Is a marine structure for berthing of vessels for loading and unloading cargo and passengers (B) Is provided with a dock gate (C) Is provided with an arrangement to pump out water when required (D) All the above

Description : A dock: (A) Is a marine structure for berthing of vessels for loading and unloading cargo and passengers (B) Is provided with a dock gate (C) Is provided with an arrangement to pump out water when required (D) All the above

Last Answer : (D) All the above

Complete maintenance of electrical motors should include periodic checks for machine _____________. A. vibration B. watertight integrity C. speed droop D. reactive power

Description : Complete maintenance of electrical motors should include periodic checks for machine _____________. A. vibration B. watertight integrity C. speed droop D. reactive power

Last Answer : Answer: A

Coast Guard Regulations (46 CFR) require that lighting fixture globes must be protected by guards if the fixtures are located in the ____________. A. steering gear room B. galley C. living quarters D. wheelhouse

Description : Coast Guard Regulations (46 CFR) require that lighting fixture globes must be protected by guards if the fixtures are located in the ____________. A. steering gear room B. galley C. living quarters D. wheelhouse

Last Answer : Answer: A

If a single phase motor is driven in any direction by any means, it starts running in that direction. Explain why?

Description : If a single phase motor is driven in any direction by any means, it starts running in that direction. Explain why?

Last Answer : Actually a pulsating torque has two components which are equal in magnitude and rotate in opposite direction with synchronous speed at unity slip. Now if the motor rotates in any direction, the ... component in this direction increases than the other component and hence motor runs in that direction.

Which of the following statements is true concerning a polyphase synchronous propulsion motor? A. The motor is started as an induction motor. B. Resistance is gradually added to the rotor circuit. C. The starting current is held below the rated current. D. The field winding is energized for starting purposes only.

Description : Which of the following statements is true concerning a polyphase synchronous propulsion motor? A. The motor is started as an induction motor. B. Resistance is gradually added to the rotor circuit. C. ... is held below the rated current. D. The field winding is energized for starting purposes only.

Last Answer : Answer: A

Coast Guard Regulations (46 CFR) require that each alternating current generator arranged for parallel operation shall be provided with _____________. A. more than one means of excitation B. individual circuit fuses C. a high back-pressure trip D. a reverse-power trip

Description : Coast Guard Regulations (46 CFR) require that each alternating current generator arranged for parallel operation shall be provided with _____________. A. more than one means of excitation B. individual circuit fuses C. a high back-pressure trip D. a reverse-power trip

Last Answer : Answer: D

The purpose of the 'heater resistors' for the winch circuit shown in the illustration is to _______________. EL-0102 A. limit the current in the heater circuit B. dispel moisture in the 'master switch' housing & control panel C. keep the winch brake housing below the dew point D. maintain winch motor operating temperature

Description : The purpose of the 'heater resistors' for the winch circuit shown in the illustration is to _______________. EL-0102 A. limit the current in the heater circuit B. dispel moisture in the ' ... panel C. keep the winch brake housing below the dew point D. maintain winch motor operating temperature

Last Answer : Answer: B

Which of the listed precautions should be taken when cleaning the internals of a motor with compressed air? A. Open the machine on both ends so as to allow the air and dust to escape. B. Be certain that the circuit breaker is opened and tagged on the feeder panel. C. Be certain that the air is clean and as dry as possible. D. All of the above.

Description : Which of the listed precautions should be taken when cleaning the internals of a motor with compressed air? A. Open the machine on both ends so as to allow the air and dust to escape. B. Be certain that the ... panel. C. Be certain that the air is clean and as dry as possible. D. All of the above.

Last Answer : Answer: D

The total resistance of a parallel circuit is always ____________. A. larger than that of the branch with the greatest resistance B. smaller than that of the branch with the lowest resistance C. equal to the sum of the individual branch resistances D. equal to the sum of the individual branch resistances divided by the number of branches

Description : The total resistance of a parallel circuit is always ____________. A. larger than that of the branch with the greatest resistance B. smaller than that of the branch with the lowest resistance C ... resistances D. equal to the sum of the individual branch resistances divided by the number of branches

Last Answer : Answer: B

The total resistance of a parallel circuit is always ____________. A. larger than the greatest branch resistance B. smaller than the lowest branch resistance C. equal to the sum of the individual branch resistances D. one-half the sum of the individual branch resistances

Description : The total resistance of a parallel circuit is always ____________. A. larger than the greatest branch resistance B. smaller than the lowest branch resistance C. equal to the sum of the individual branch resistances D. one-half the sum of the individual branch resistances

Last Answer : Answer: B

Capacitors can be used in electric distribution systems to improve power factor. This is accomplished by seesawing energy between the capacitor and the _____________. A. generator B. inductive loads C. resistive loads D. all of the above

Description : Capacitors can be used in electric distribution systems to improve power factor. This is accomplished by seesawing energy between the capacitor and the _____________. A. generator B. inductive loads C. resistive loads D. all of the above

Last Answer : Answer: B

Which of the following statement(s) is/are true concerning the treatment of MOFS? a. Prevention and therapy of MOFS requires control of the infectious or inflammatory source b. Restoration of normal clinical parameters such as blood pressure, pulse rate, and urine output ensures optimal resuscitation in most patients c. Branch chain amino acids play and important role in the nutritional support of the patient d. Because of the nature of gut injury, total parenteral nutrition is preferred for most patients with MOFS

Description : Which of the following statement(s) is/are true concerning the treatment of MOFS? a. Prevention and therapy of MOFS requires control of the infectious or inflammatory source b. Restoration of normal ... of the nature of gut injury, total parenteral nutrition is preferred for most patients with MOFS

Last Answer : Answer: a, c The therapy of MOFS is directed towards interrupting the involving pathophysiologic process and providing an optimal physiologic environment for healing and recovery. ... Enteral absorption and processing of nutrients appears superior to TPN and lessens overall complications

Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut (C) A slot is cut in the middle of nut along the length and a cap screw is provided to tighten the two parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Description : Jam nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Last Answer : (A) A smaller nut is tightened against main nut creating friction at the contacting surface

Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut (C) A slot is cut in the middle of nut along the length and a cap screw is provided to tighten the two parts of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Description : Castle nut is a locking device in which (A) A smaller nut is tightened against main nut creating friction at the contacting surface (B) A split pin is passed through diametrically opposite slots in nut and ... of nut separated by slot (D) An elastic piece is tightened in the nut by a setscrew

Last Answer : (B) A split pin is passed through diametrically opposite slots in nut and a hole in bolt and the two ends of split pin are separated and bent back on nut

In the lighting distribution circuit shown in the illustration, if all switches are closed and fuse 'F2' were to open, all lights on branches ____________. EL-0013 A. '1', '2', and '3' would go out B. '1' and '3' would would burn dimly, while branch '2' would burn normally C. '1', '2', and '3' would burn dimly D. '1' and '3' would go out, while branch '2' would remain lit

Description : In the lighting distribution circuit shown in the illustration, if all switches are closed and fuse 'F2' were to open, all lights on branches ____________. EL-0013 A. '1', '2', and '3' would go out B. '1' ... and '3' would burn dimly D. '1' and '3' would go out, while branch '2' would remain lit

Last Answer : Answer: D