Description : Maximum permissible residual chlorine in treated water should be __________ mg/litre. (A) 0.001 to 0.01 (B) 0.2 to 0.3 (C) 2 to 3 (D) 5 to 10
Last Answer : (B) 0.2 to 0.3
Description : Safe limit' called Threshold Limit Value (TLV) of carbon monoxide in atmospheric air is < 50 ppm. The main source of carbon monoxide pollutant in air is the (A) Industrial chimney exhaust (B) Automobiles exhaust (C) Photochemical reaction in polluted atmosphere (D) Burning of domestic fuel
Last Answer : (B) Automobiles exhaust
Description : Maximum permissible concentration of copper in drinking water in mg/L, is – (1) 0.01 (2) 0.05 (3) 1.0 (4) 2.0
Last Answer : (3) 1.0 Explanation: The 1959 WHO International Standards for Drinking Water suggested that concentrations of copper greater than 1.5 mg/litre would markedly impair the potability of the water. However, ... 1.0 mg/litre was established for copper, based on its laundry and other staining properties.
Description : Maximum permissible concentration of copper in drinking water in mg/L is - (1) 0.01 (2) 0.05 (3) 1.0 (4) 2.0
Last Answer : (3) 1.0 Explanation: In the first edition of the Guidelines for Drinking Water Quality, published in 1984, a guideline value of 1.0 mg/litre was established for copper, based on its laundry and other staining properties.
Description : Maximum permissible concentration of copper in drinking water in mg/L is (1) 0.01 (2) 0.05 (3) 1.0 (4) 2.0
Last Answer : 1.0
Description : Threshold limit value (TLV) means maximum permissible/acceptable concentration. TLV of phosgene in air is about __________ ppm (parts per million). (A) 0.002 (B) 0.2 (C) 1.2 (D) 4.8
Last Answer : (B) 0.2
Description : What is the typical separation between the two conductors in a parallel wire line? A. 0.001 to 0.01 m B. 200 to 500 mm C. 0.635 to 15.24 cm D. 2.5 to 5 in.
Last Answer : C. 0.635 to 15.24 cm
Description : In a transistor Colpitts oscillator, C1 = 0.001 µF, C2 = 0.01 µF and L = 5 µH. The frequency of oscillation in MHz will be (a) 2.37 MHz (b) 10.00 MHz (c) 11.54 MHz (d) 9.09 MHz
Last Answer : c
Description : In a number sequence what is 0.001 0.01 0.1 1?
Last Answer : Each successive number is ten times the one before it.
Description : What is the Next number in the sequence 0.001 0.01 0.1 1?
Last Answer : 10
Description : A micron is equal to – (1) 0.1 ram (2) 0.01 mm (3) 0.001 mm (4) 0.0001 mm
Last Answer : (3) 0.001 mm Explanation: 1 micron = 0.001 millimeters. A micrometre (micron) is one-millionth of a metre (or one-thousandth of a millimetre, 0.001 mm). Its unit symbol in the ... is a common unit of measurement for wavelengths of infrared radiation as well as sizes of cells and bacteria.
Description : Period of oscillation of 3 cm microwaves in seconds is (1) 1 x 10¹⁰ (2) 1 x 10⁻¹⁰ (3) 0.01 (4) 0.001
Last Answer : (2) 1 x 10⁻¹⁰ Explanation: The period of oscillation of 3 cm microwaves is 1 x 10^-10 (Physics, Volume 1, by Halliday). The period of oscillation is the smallest interval of time in which a system undergoing oscillation returns to the state it was in at the beginning of the oscillation.
Description : A conductor with a cross-sectional area of one circular mil would have a diameter of _____________. A. 0.1 inches B. 0.01 inches C. 0.001 inches D. 0.0001 inches
Last Answer : Answer: C
Description : Very low pressure is expressed in microns (μ), which is equal to__________ mm of Hg column (absolute) at 0°C. (A) 0.0001 (B) 0.001 (C) 0.01 (D) 0.1
Last Answer : (B) 0.001
Description : Carbon content in steel is __________ percent. (A) 0.1-2 (B) 4-6 (C) 2-4 (D) 0.001-0.01
Last Answer : (A) 0.1-2
Description : Angstrom (Å) is equal to (a) 0.01 mm (b) 0.001 mm (c) 0.0001 mm (d) 0.00001 mm
Last Answer : (b) 0.001 mm
Description : Rotary vacuum pumps can reduce the absolute pressure to as low as __________ mm Hg. (A) 1 (B) 0.1 (C) 0.01 (D) 0.001
Last Answer : (C) 0.01
Description : The void ratio of a soil sample decreases from 1.50 to 1.25 when the pressure is increased from 25 tonnes/m2 to 50 tonnes/m2 , the coefficient of compressibility is (A) 0.01 (B) 0.02 (C) 0.05 (D) 0.001
Last Answer : (A) 0.01
Description : The difference in one unit of Rockwell hardness number corresponds to a difference in the depth of indentation of __________ mm. (A) 0.001 (B) 0.01 (C) 0.002 (D) 0.02
Last Answer : Option C
Description : When a constant discharge 2.91 litres/sec. was obtained in a pumping test, the draw downs in the test wells at 3 m and 6.184 m were 2.6 m and 0.3 m respectively. If over-all depth of the pumping well was 16 m, the ... (A) 0.0005 cm/sec (B) 0.001 cm/sec (C) 0.002 cm/sec (D) 0.01 cm/sec
Last Answer : Answer: Option B
Description : The specific gravity of water is taken as (A) 0.001 (B) 0.01 (C) 0.1 (D) 1
Last Answer : Answer: Option D
Description : Pick up the incorrect statement from the following: (A) Dimensions are measured to the nearest 0.01 m (B) Areas are measured to the nearest 0.01 sq.m (C) Cubic contents are measured to the nearest 0.1 cum (D) Weights are measured to the nearest 0.001 tonnes
Last Answer : (D) Weights are measured to the nearest 0.001 tonnes
Description : The time of closing the cycle, in modern circuit breakers is (a) 0.003 sec (b) 0.001 sec (c) 0.01 sec (d) 0.10 sec (e) none of the above
Last Answer : (a) 0.003 sec
Description : The mechanical splice attenuation loss is _____ dB or less ∙ a. 0.1 ∙ b. 0.01 ∙ c. 0.001 ∙ d. 1
Last Answer : a. 0.1
Description : A Huffman code: A = 1, B = 000, C = 001, D = 01 ,P(A) = 0.4, P(B) = 0.1, P(C) = 0.2, P(D) = 0.3 The average number of bits per letter is A. 8.0 bit B. 2.0 bit C. 1.9 bit D. 2.1 bit
Last Answer : C. 1.9 bit
Description : A Huffman code: A = 1, B = 000, C = 001, D = 01 ,P(A) = 0.4, P(B) = 0.1, P(C) = 0.2, P(D) = 0.3 The average number of bits per letter is a. 8.0 bit b. 2.0 bit c. 1.9 bit d. 2.1 bit
Last Answer : c. 1.9 bit
Description : A micron is equal to (1) 0.1 mm (2) 0.01 mm (3) 0.001 mm(4) 0.0001 mm
Last Answer : 0.001 mm
Description : Threshold Limit Value (TLV) is the maximum allowable concentration (i.e. safe limit) of pollutants in air. Safe limit for SO2 in air is __________ ppm. (A) 5 (B) 500 (C) 1000 (D) 2000
Last Answer : (A) 5
Description : Threshold limit value (TLV) of CO in air is __________ ppm. (A) 5 (B) 50 (C) 2000 (D) 5000
Last Answer : (B) 50
Description : An odd shaped body weighing 7.5 kg and occupying 0.01 m3 volume will be completely submerged in a fluid having specific gravity of (A) 1 (B) 1.2 (C) 0.8 (D) 0.75
Description : Hot water (0.01 m3 /min) enters the tube side of a counter current shell and tube heat exchanger at 80°C and leaves at 50°C. Cold oil (0.05 m3 /min) of density 800 kg/m3 and specific heat of ... mean temperature difference in °C is approximately (A) 32 (B) 37 (C) 45 (D) 50
Last Answer : (A) 32
Description : The reaction A → B is conducted in an adiabatic plug flow reactor (PFR). Pure A at a concentration of 2 kmol/m3 is fed to the reactor at the rate of 0.01 m3 /s and at a temperature of 500 K. If the exit ... /kmole. K (may be assumed to be independent of temperature)) (A) 400 (B) 500 (C) 600 (D) 1000
Last Answer : (C) 600
Description : Threshold limit value (TLV) i.e., the maximum permissible safe limit of phosgene gas which Hitler used to use to kill his enemies in 'gas chamber' is about __________ ppm. (A) < 1 (B) 10-100 (C) 100-200 (D) 100-1000
Last Answer : (A) < 1
Description : Safe and adequate daily dietary intake of chromium in adults in mg is (A) 0.01–0.02 (B) 0.02–0.03 (C) 0.03–0.04 (D) 0.05–0.2
Last Answer : Answer : D
Description : Dose of chlorine for disinfection of water is about __________ mg/litre of water. (A) 0.01 (B) 0.1 (C) 0.3 (D) 1
Last Answer : (D) 1
Description : Mean drift velocity of electron in a copper wire having cross-sectional area 5.0 × 10-6 m2 carrying current of 1 A and having number density 8.5 × 1028 m3 is A. 0.015 mm s-1 B. 0.1 mm s-1 C. 0.5 mm s-1 D. 0.25 mm s-1
Last Answer : 0.015 mm s-1
Description : Time required for the organism to eliminate 50% the total body burden or tissue concentration of chemical is referred as – (1) Threshold limit time (2) Halftime life (3) Residual-period (4) Half-life period
Last Answer : (4) Half-life period Explanation: Time required for the organism to eliminate 50 per cent of the total body burden or tissue concentration of chemical is referred to as Half Life Period.
Description : Time required for the organism to eliminate 50% the total body burden or tissue concentration of chemical is referred as (1) Threshold limit time (2) Half-time life (3) Residual period (4) Half-life period
Last Answer : Half-life period
Description : Colburn analogy is applicable for the value of Prandtl number from (A) 0.001 to 1 (B) 0.6 to 120 (C) 0.5 to 5 (D) 120 to 400
Last Answer : (B) 0.6 to 120
Description : 01. When the pressure intensity at a point is less than the local atmospheric pressure, then the difference of these two pressures is called vacuum pressure. A) Agree B) Disagree
Last Answer : Option A
Description : MIS account in multiple of Rs. 1500/- can be made instead of Rs. 1000/- MIS and the maximum limit of investment in a single account has been raised from Rs. 3 lakh to Rs. 4.5 lakh and in joint account opened by two ... to Rs. 9 Lakh. Wef a) 01.8.2007 b) 12.5.2008 c) 30.08.2009 d) None of these
Last Answer : a) 01.8.2007
Description : Mark the correct option a) There is no maximum limit of deposit in TD accounts of any type b) No subsequent withdrawal allowed in TD accounts before date of maturity c) The investment under 5 years TD ... the benefit of Section 80C f the income tax Act 1961 from 01-04-2007 d) All the above
Last Answer : d) All the above
Description : At 750°K and 1 atm, the approximate value of Schmidt number for air is (A) 0.01 (B) 0.1 (C) 1 (D) 10
Last Answer : (B) 0.1
Description : No maximum limit on saving bank accounts from a) 01 Oct 2011 b) 01 Dec 2011 c) 01 Jan 2012 d) None of these
Last Answer : a) 01 Oct 2011
Description : Which of the following situations can be approximated to a steady state heat transfer system? (A) A red hot steel slab (having outside surface temperature as 1300°C) exposed to the atmospheric air at ... flowing at the rate of 6 Kg/minute through a copper pipe exposed to atmospheric air at 35°C
Last Answer : (B) 10 kg of dry saturated steam at 8 kgf/cm2 flowing through a short length of stainless steel pipe exposed to atmospheric air at 35°C
Description : The ambient air quaility standard (24 hours' average) for lead in industrial area is (1) 0.65 pg/m3 (2) 0/5 pg/m3 (3) 1.0 pg/m3 (4) 1.5 pg/m3
Last Answer : (4) 1.5 pg/m3 Explanation: The ambient air quality standard (24 hours' average) for lead in industrial area is 1.5 pg/m3
Description : A bed consists of particles of density 2000 kg/m3 . If the height of the bed is 1.5 metres and its porosity 0.6, the pressure drop required to fluidise the bed by air is (A) 25.61 kPa (B) 11.77 kPa (C) 14.86 kPa (D) 21.13 kPa
Last Answer : (B) 11.77 kPa
Description : Bed pressure drop in an air fluidised bed of catalyst particles (ρp = 200 kg/m3, Dp = 0.05 cm) of 60 cm bed depth and bed porosity of 0.5 expressed in cm of water (manometer) is (A) 90 (B) 60 (C) 45 (D) 30
Last Answer : (B) 60
Description : The ambient air quaility standard (24 hours’ average) for lead in industrial area is (1) 0.65 µg/m3 (2) 0.75 µg/m3 (3) 1.0 µg/m3 (4) 1.5 µg/m3
Last Answer : 1.5 µg/m3
Description : Daily requirement of copper in adults is about (A) 0.5 mg (B) 1 mg (C) 2.5 mg (D) 5 mg
Last Answer : Answer : C