State two similarities and two dissimilarities between heat and work.

State two similarities and two dissimilarities between heat and work.
by

1 Answer

Answer :

Heat and work

Similarities- Both are not properties of system, both are boundary phenomena, both are path functions, both are form of energy

Dissimilarities-Work is high grade energy, heat is low grade energy ; Entire heat cannot be converted into work, but entire work can be converted into heat ; System can possess heat, but it never possess work
by

Related questions

Give two dissimilarities of popular struggles in Nepal and Bolivia ? -SST 10th

Description : Give two dissimilarities of popular struggles in Nepal and Bolivia ? -SST 10th

Last Answer : The dissimilarities between the struggles in Nepal and Bolivia: 1. The struggle in Nepal was to establish democracy while in Bolivia, the people protested against the democratic government for changing an ... in Bolivia, it was the change in the decision of the government regarding water rights.

The coefficient of performance is the ratio of the refrigerant effect to the (a) heat of compression (b) work done by compressor (c) enthalpy increase in compressor (d) all of the above

Description : The coefficient of performance is the ratio of the refrigerant effect to the (a) heat of compression (b) work done by compressor (c) enthalpy increase in compressor (d) all of the above

Last Answer : Ans: d

Heat engine uses ______ energy to produce mechanical work. a. Thermal b. Fluid c. Kinetic d. Electric (Ans:a)

Description : Heat engine uses ______ energy to produce mechanical work. a. Thermal b. Fluid c. Kinetic d. Electric (Ans:a)

Last Answer : Which of the following is not an internal Combustion (IC) engine? a. Gas engine b. Wankel engine c. Jet engine d. Stirling engine (Ans:d)

Adiabatic compression is one in which A. Temperature during compression remains constant B. No heat leaves or enters the compressor cylinder during compression C. Temperature rise follows a linear relationship D. Work done is maximum.

Description : Adiabatic compression is one in which A. Temperature during compression remains constant B. No heat leaves or enters the compressor cylinder during compression C. Temperature rise follows a linear relationship D. Work done is maximum.

Last Answer : ANSWER : B

An engine working on air standard Otto cycle has a cylinder diameter of 10 cm and stroke length of 15 cm. The ratio of specific heats for air is 1.4. If the clearance volume is 196.3 cc and the heat supplied per kg of air per cycle is 1800 kJ/kg, then work output per cycle per kg of air is a. 879.1 kJ/ b. 890.2 kJ c. 895.3 kJ d. 973.5 kJ

Description : An engine working on air standard Otto cycle has a cylinder diameter of 10 cm and stroke length of 15 cm. The ratio of specific heats for air is 1.4. If the clearance volume is 196.3 cc and the heat supplied per kg of air per ... kg of air is a. 879.1 kJ/ b. 890.2 kJ c. 895.3 kJ d. 973.5 kJ

Last Answer : ANSWER d. 973.5 kJ

An engine is supplied with 4 kW of heat energy. It is found that it produce 4 kW of work. Which kind of perpetual machine it is? Which law is violated? Also describe other kind of perpetual machine you know.

Description : An engine is supplied with 4 kW of heat energy. It is found that it produce 4 kW of work. Which kind of perpetual machine it is? Which law is violated? Also describe other kind of perpetual machine you know.

Last Answer : PMM-II: A heat engine which violates Kelvin plank statement of the second law of thermodynamics is known as Perpetual Motion Machine of the second kind (PMM-II). Or 100 percent efficient machine which is ... no machine can produce energy of its own without consuming any other form of energy.

Categorize point and path functions from following. (pressure, heat, internal energy, temperature, work, total enthalpy.)

Description : Categorize point and path functions from following. (pressure, heat, internal energy, temperature, work, total enthalpy.)

Last Answer : Point function-Pressure, temperature, internal energy, total enthalpy Path function-Heat, Work

Describe only construction and working of pipe in pipe heat exchanger. State it’s two applications.

Description : Describe only construction and working of pipe in pipe heat exchanger. State it’s two applications.

Last Answer : Pipe Heat Exchanger: Construction and Working : In Pipe heat exchanger design, an important factor is the type of flow pattern in the heat exchanger. A pipe heat exchanger will ... more compact. Application : Oil refinery industries , Waste water management, Refrigeration system  

Describe any two sources of air leak in surface condenser. Also describe effect of air leak on latent heat of steam and cooling water requirements.

Description : Describe any two sources of air leak in surface condenser. Also describe effect of air leak on latent heat of steam and cooling water requirements.

Last Answer : ✓ The main sources of air leakage found in condenser are given below: 1) There is leakage of air from atmosphere at the joint of the parts which are internally under a pressure less ... hence evaporation enthalpy of steam increases therefore more amount of cooling water required in the condenser. 

The formation of frost on cooling coils in a refrigerator (a) increases heat transfer (b) improves C.O.P. of the system (c) increases power consumption (d) reduces power consumption

Description : The formation of frost on cooling coils in a refrigerator (a) increases heat transfer (b) improves C.O.P. of the system (c) increases power consumption (d) reduces power consumption

Last Answer : Ans: c

The evolution of heat of solution takes place in ammonia absorption plant when (a) ammonia vapour goes into solution (b) ammonia vapour is driven out of solution (c) lithium bromide mixes with ammonia (d) weak solution mixes with strong solution

Description : The evolution of heat of solution takes place in ammonia absorption plant when (a) ammonia vapour goes into solution (b) ammonia vapour is driven out of solution (c) lithium bromide mixes with ammonia (d) weak solution mixes with strong solution

Last Answer : Ans: a

Vertical lines on pressure-enthalpy chart show constant (a) pressure lines (b) temperature lines (c) total heat lines (d) entropy lines

Description : Vertical lines on pressure-enthalpy chart show constant (a) pressure lines (b) temperature lines (c) total heat lines (d) entropy lines

Last Answer : Ans: c

Choose the wrong statement (a) Temperature of medium being cooled must be below that of the evaporator (b) Refrigerant leaves the condenser as liquid (c) All solar thermally operated absorption systems are capable only of intermittent operation (d) frost on evaporator reduces heat transfer

Description : Choose the wrong statement (a) Temperature of medium being cooled must be below that of the evaporator (b) Refrigerant leaves the condenser as liquid (c) All solar thermally operated absorption systems are capable only of intermittent operation (d) frost on evaporator reduces heat transfer

Last Answer : Ans: a

Choose the correct statement (a) A refrigerant should have low latent heat (b) If operating temperature of system is low, then refrigerant with low boiling point should be used (c) Pre-cooling and sub-cooling bf refrigerant are same (d) Superheat and sensible heat of a. refrigerant are same

Description : Choose the correct statement (a) A refrigerant should have low latent heat (b) If operating temperature of system is low, then refrigerant with low boiling point should be used (c) Pre-cooling and sub-cooling bf refrigerant are same (d) Superheat and sensible heat of a. refrigerant are same

Last Answer : Ans: b

Short horizontal lines on pressure-enthalpy chart show (a) constant pressure lines (b) constant temperature lines (c) constant total heat lines (d) constant entropy lines

Description : Short horizontal lines on pressure-enthalpy chart show (a) constant pressure lines (b) constant temperature lines (c) constant total heat lines (d) constant entropy lines

Last Answer : Ans: a

If a heat pump cycle operates between the condenser temperature of +27°C and evaporator temperature of - 23°C,then the Carnot COP will be (a) 0.2 (b) 1.2 (c) 5 (d) 6

Description : If a heat pump cycle operates between the condenser temperature of +27°C and evaporator temperature of - 23°C,then the Carnot COP will be (a) 0.2 (b) 1.2 (c) 5 (d) 6

Last Answer : Ans: d

Pick up the correct statement about giving up of heat from one medium to other in ammonia absorption system (a) strong solution to weak solution (b) weak solution to strong solution (c) strong solution to ammonia vapour (d) ammonia vapour to strong solution.

Description : Pick up the correct statement about giving up of heat from one medium to other in ammonia absorption system (a) strong solution to weak solution (b) weak solution to strong solution (c) strong solution to ammonia vapour (d) ammonia vapour to strong solution.

Last Answer : Ans: b

Which of the following is not a desirable property of a refrigerant (a) highmisibility with oil (b) low boiling point (c) good electrical conductor (d) large latent heat

Description : Which of the following is not a desirable property of a refrigerant (a) highmisibility with oil (b) low boiling point (c) good electrical conductor (d) large latent heat

Last Answer : Ans: c

At lower temperatures and pressures, the latent heat of vaporization of a refrigerant (a) decreases (b) increases (c) remains same (d) depends on other factors

Description : At lower temperatures and pressures, the latent heat of vaporization of a refrigerant (a) decreases (b) increases (c) remains same (d) depends on other factors

Last Answer : Ans: b

Formation of frost on evaporator in refrigerator (a) results in loss of heat due to poor heat transfer (b) increases heat transfer rate (c) decreases compressor power. (d) can be avoided by proper design

Description : Formation of frost on evaporator in refrigerator (a) results in loss of heat due to poor heat transfer (b) increases heat transfer rate (c) decreases compressor power. (d) can be avoided by proper design

Last Answer : Ans: a

In a refrigeration system, heat absorbed in comparison to heat rejected is (a) more (b) less (c) less for small capacity and more for high capacity. (d) more for small capacity and less for high capacity

Description : In a refrigeration system, heat absorbed in comparison to heat rejected is (a) more (b) less (c) less for small capacity and more for high capacity. (d) more for small capacity and less for high capacity

Last Answer : Ans: b

The refrigerant for a refrigerator should have (a) high sensible heat (b) high total heat (c) high latent heat (d) low latent heat

Description : The refrigerant for a refrigerator should have (a) high sensible heat (b) high total heat (c) high latent heat (d) low latent heat

Last Answer : Ans: c

The heat content of air is called the _____ of the air. a. Temperature b. Humidity c. Enthalpy d. Psychrometry e. Entropy

Description : The heat content of air is called the _____ of the air. a. Temperature b. Humidity c. Enthalpy d. Psychrometry e. Entropy

Last Answer : ANSWER : C

Humidification is the process of addition moisture in air at A. constant wet bulb temperature B. constant dry bulb temperature C. constant latent heat D. none of the above

Description : Humidification is the process of addition moisture in air at A. constant wet bulb temperature B. constant dry bulb temperature C. constant latent heat D. none of the above

Last Answer : ANSWER : B

When, H1 = Total heat of air entering the coil (heating or cooling) H2 = Total heat of air leaving the coil (heating or cooling) H3 = Total heat of air at the end of the process (humidification or dehumidification) then, the sensible heat factor (H2 – H1) / (H3 – H1) represents the process of A. cooling and humidification B. cooling and dehumidification C. heating and humidification D. heating and dehumidification

Description : When, H1 = Total heat of air entering the coil (heating or cooling) H2 = Total heat of air leaving the coil (heating or cooling) H3 = Total heat of air at the end of ... A. cooling and humidification B. cooling and dehumidification C. heating and humidification D. heating and dehumidification

Last Answer : ANSWER : C

What is sensible cooling of air? A. the cooling in which sensible heat of air is removed in order to reduce temperature B. the cooling in which temperature of air is reduced without changing in its moisture content C. both a. and b. D. none of the above

Description : What is sensible cooling of air? A. the cooling in which sensible heat of air is removed in order to reduce temperature B. the cooling in which temperature of air is reduced without changing in its moisture content C. both a. and b. D. none of the above

Last Answer : ANSWER : C

In adiabatic evaporative cooling, heat transfer between chamber and surroundings is ____ A. zero B. high C. low D. none of the mentioned

Description : In adiabatic evaporative cooling, heat transfer between chamber and surroundings is ____ A. zero B. high C. low D. none of the mentioned

Last Answer : ANSWER : A

When air passes through silica gel, A. it absorbs water vapour molecules B. latent heat of condensation is released C.dbt of air increases D. all of the mentioned

Description : When air passes through silica gel, A. it absorbs water vapour molecules B. latent heat of condensation is released C.dbt of air increases D. all of the mentioned

Last Answer : ANSWER : D

In four stroke engine which of the following is also known as power stroke a. Suction stroke b. Compression stroke c. Expansion stroke d. Exhaust stroke (Ans:c) Measurements of fuel and air consumption, brake power and incylinder pressure. Tutorials on engine performance parameters. Heat balance sheet. Engine performance curves. 1. The increase in intake air temperature into IC engine,___________its efficiency A. increase B. decrease C. does not alter D. unpredictable on

Description : In four stroke engine which of the following is also known as power stroke a. Suction stroke b. Compression stroke c. Expansion stroke d. Exhaust stroke (Ans:c) Measurements of fuel and air ... into IC engine,___________its efficiency A. increase B. decrease C. does not alter D. unpredictable on

Last Answer : ANSWER : B

Alcohols alone cannot be used in CI engines as a) their self ignition temperature is high b) latent heat of vaporization is high c) all of the mentioned d) none of the mentioned

Description : Alcohols alone cannot be used in CI engines as a) their self ignition temperature is high b) latent heat of vaporization is high c) all of the mentioned d) none of the mentioned

Last Answer : Answer: c Explanation: None.

Which of the following statement is not correct with respect to alcohols as alternate fuel in IC engines a) anti-knock characteristics of alcohol is poor b) alcohol contains about half the heat energy of gasoline/litre c) alcohol does not vaporize as easily as gasoline d) alcohols are corrosive in nature

Description : Which of the following statement is not correct with respect to alcohols as alternate fuel in IC engines a) anti-knock characteristics of alcohol is poor b) alcohol contains about half the heat ... /litre c) alcohol does not vaporize as easily as gasoline d) alcohols are corrosive in nature

Last Answer : Answer: a Explanation: Anti-knock characteristics of alcohol is good.

The method of determination of indicated power of multi cylinder SI engine is by use of (a) Morse test (b) Prony brake test (c) Motoring test (d) Heat balance test

Description : The method of determination of indicated power of multi cylinder SI engine is by use of (a) Morse test (b) Prony brake test (c) Motoring test (d) Heat balance test

Last Answer : Ans : a

All heat engines utilize a. lower heating value of oil b. higher heating value of oil c. net calorific value of oil d. calorific value of fuel

Description : All heat engines utilize a. lower heating value of oil b. higher heating value of oil c. net calorific value of oil d. calorific value of fuel

Last Answer : ANSWER a. lower heating value of oil

A diesel engine is usually more efficient than a spark ignition engine because a. Diesel being a heavier hydrocarbon, release more heat per kg than gasoline b. The air standard efficiency of diesel cycle is higher than the Otto cycle, at a fixed compression ratio c. The compression ratio of a diesel engine is higher than that of an Spark ignition engine d.Self ignition temperature of diesel is higher than that of gasoline.

Description : A diesel engine is usually more efficient than a spark ignition engine because a. Diesel being a heavier hydrocarbon, release more heat per kg than gasoline b. The air standard efficiency of diesel ... an Spark ignition engine d.Self ignition temperature of diesel is higher than that of gasoline.

Last Answer : ANSWER c. The compression ratio of a diesel engine is higher than that of an S.I engine

For an engine operating on air standard Otto cycle, the clearance volume is 10% of the swept volume. The specific heat ratio of air is 1.4. The air standard cycle efficiency is a. 38.3 % b. 39.8 % c. 60.2 % d. 61.7 %

Description : For an engine operating on air standard Otto cycle, the clearance volume is 10% of the swept volume. The specific heat ratio of air is 1.4. The air standard cycle efficiency is a. 38.3 % b. 39.8 % c. 60.2 % d. 61.7 %

Last Answer : ANSWER d. 61.7%

In diesel engine, the fuel is ignited by a. spark b. injected fuel c. heat resulting from compressing air that is supplied for combustion d. ignitor

Description : In diesel engine, the fuel is ignited by a. spark b. injected fuel c. heat resulting from compressing air that is supplied for combustion d. ignitor

Last Answer : ANSWER c. heat resulting from compressing air that is supplied for combustion

For the same peak pressure and heat input a. Otto cycle is more efficient b. Diesel cycle is more efficient c. Both are equally efficient d. None of the above

Description : For the same peak pressure and heat input a. Otto cycle is more efficient b. Diesel cycle is more efficient c. Both are equally efficient d. None of the above

Last Answer : ANSWER b. Diesel cycle is more efficient

For same compression ratio and heat input a. Otto cycle is more efficient b. Diesel cycle is more efficient c. Both are equally efficient d. None of the above

Description : For same compression ratio and heat input a. Otto cycle is more efficient b. Diesel cycle is more efficient c. Both are equally efficient d. None of the above

Last Answer : ANSWER a. Otto cycle is more efficient

How the efficiency of the SI engine is affected by the specific heat ratio (γ) of the working fluid? a. the efficiency of the engine increases with increase in specific heat ratio (γ) of the working fluid b. the efficiency of the engine decreases with increase in specific heat ratio (γ) of the working fluid c. the efficiency of the engine does not affected by change in specific heat ratio (γ) of the working fluid d. none of the above

Description : How the efficiency of the SI engine is affected by the specific heat ratio (γ) of the working fluid? a. the efficiency of the engine increases with increase in specific heat ratio (γ) of the working ... not affected by change in specific heat ratio (γ) of the working fluid d. none of the above

Last Answer : ANSWER a. the efficiency of the engine increases with increase in specific heat ratio (γ) of the working fluid

The efficiency of the Otto cycle is independent of a. Heat supplied b. Compression ratio c. Ratio of specific heats d. None of the above

Description : The efficiency of the Otto cycle is independent of a. Heat supplied b. Compression ratio c. Ratio of specific heats d. None of the above

Last Answer : Answer a. Heat supplied

In which of the following cycle heat is added at constant pressure? a. Otto cycle b. Diesel cycle c. Dual cycle d. Carnot cycle

Description : In which of the following cycle heat is added at constant pressure? a. Otto cycle b. Diesel cycle c. Dual cycle d. Carnot cycle

Last Answer : Answer b. Diesel cycle

In which of the following cycle heat is added at constant volume? a. Otto cycle b. Diesel cycle c. Dual cycle d. Carnot cycle

Description : In which of the following cycle heat is added at constant volume? a. Otto cycle b. Diesel cycle c. Dual cycle d. Carnot cycle

Last Answer : Answer a. Otto cycle

Define heat exchanger. Classify heat exchangers based on geometry, direction of fluids, method of heat exchange.

Description : Define heat exchanger. Classify heat exchangers based on geometry, direction of fluids, method of heat exchange.

Last Answer : 1. A heat exchanger is a device, which transfers thermal energy between two fluids at different temperatures. 2. In most common engineering applications, both fluids are in motion and the ... free or forced convection ii. Boiling or condensation iii. Radiation or combined convection radiation

In a constant pressure process steam is generated from 10 bar and 0.8 dry condition till it become dry and saturated. Determine amount of heat added per kg of steam. From steam table at 10 bar Tsat = 179.9°C hf = 762.6 kl/kg, hg = 2776.2 kJ/kg

Description : In a constant pressure process steam is generated from 10 bar and 0.8 dry condition till it become dry and saturated. Determine amount of heat added per kg of steam. From steam table at 10 bar Tsat = 179.9°C hf = 762.6 kl/kg, hg = 2776.2 kJ/kg 

Last Answer : Constant pressure process Final condition of steam is dry saturated Enthalpy of dry steam = hg= hf + hfg =2776.2 KJ/Kg .Given Latent heat of vaporization = hfg = hg - hf =2776.2-762.6 =2013.6 KJ/Kg Initial condition ... hfg = 762.6+0.8 X 2013.6 =2373.48 KJ/Kg Heat added = hg-hw = 402.72 KJ/kg

Identify modes of heat transfer involved applications with brief explanation. (1) Radiator of automobile (2) Condenser of domestic refrigerator.

Description : Identify modes of heat transfer involved applications with brief explanation. (1) Radiator of automobile (2) Condenser of domestic refrigerator.

Last Answer : Modes of heat transfer Automobile radiator-A radiator is a type of heat exchanger. It is designed to transfer heat from the hot coolant that flows through it to the air blown through ... of heat transfer plays very important deciding factor transferring heat from condenser tube to atmosphere.  

In a boiler enthalpy of water supplied was 2000 kJ/kg. Enthalpy being added by fuel combustion is 3200 kJ/kg. Using first law of thermodynamics, find amount of heat supplied if steam generation rate is 10 tons per hour.

Description : In a boiler enthalpy of water supplied was 2000 kJ/kg. Enthalpy being added by fuel combustion is 3200 kJ/kg. Using first law of thermodynamics, find amount of heat supplied if steam generation rate is 10 tons per hour.

Last Answer : Heat supplied Q = m (h2-h1) …….(Steady flow energy equation for boiler) ; h2=3200 KJ/kg h1=2000 KJ/kg m = 10 Tons /hour = (10 x 1000)/3600 kg/sec = 2.77 Kg/sec Q = 2.77(3200-2000) = 3324 KJ/sec heat supplied for 10 Tons/hr steam generation

Intercooling in multistage compression is done A. To cool the air during compression B. To cool the air at delivery C. To enable compression in two stages D. To minimize the work of compression

Description : Intercooling in multistage compression is done A. To cool the air during compression B. To cool the air at delivery C. To enable compression in two stages D. To minimize the work of compression

Last Answer : ANSWER : D

For minimum work input in a two stage compression process the intermediated pressure is the A. Arithmetic process of suction and discharge pressure B. Logarithmic mean of suction and discharge pressure C. Geometric mean of suction and discharge pressure D. Hyperbolic mean of suction and discharge

Description : For minimum work input in a two stage compression process the intermediated pressure is the A. Arithmetic process of suction and discharge pressure B. Logarithmic mean of suction and discharge pressure C. Geometric mean of suction and discharge pressure D. Hyperbolic mean of suction and discharge

Last Answer : ANSWER : C

Which of the following engine can work on very lean mixture a. Spark ignition engine b. compression ignition engine c. two stroke engine d. Four stroke engine

Description : Which of the following engine can work on very lean mixture a. Spark ignition engine b. compression ignition engine c. two stroke engine d. Four stroke engine

Last Answer : ANSWER b. compression ignition engine

Most of the domestic refrigerators work on the following refrigeration system (a) vapour compression (b) vapour absorption (c) carnot cycle (d) electrolux refrigerator

Description : Most of the domestic refrigerators work on the following refrigeration system (a) vapour compression (b) vapour absorption (c) carnot cycle (d) electrolux refrigerator

Last Answer : Ans: a