Represent constant volume process on PV & TS diagram for steam.

Represent constant volume process on PV & TS diagram for steam.
by

1 Answer

Answer :

Represent constant volume process on PV & TS diagram for steam.

image

by

Related questions

Represent generation of steam on H-S diagram. Show constant dryness fraction lines, constant temperature lines, saturated line and superheated region on the same.

Description : Represent generation of steam on H-S diagram. Show constant dryness fraction lines, constant temperature lines, saturated line and superheated region on the same.

Last Answer : Represent generation of steam on H-S diagram. Show constant dryness fraction lines, constant temperature lines, saturated line and superheated region on the same.

A gas is compressed from 1 bar and 30°C to 5 bars and 30°C. Identify process and show on PV diagram.

Description : A gas is compressed from 1 bar and 30°C to 5 bars and 30°C. Identify process and show on PV diagram.

Last Answer : Gas is compressed from (1) 1 bar 30 0C to (2) 5 bar 30 0C Temp is constant. Hence process is isothermal. P x V = Constant

Out of constant pressure and constant volume lines on TS diagram which line has higher slope ? And whether slope is constant or variable ?

Description : Out of constant pressure and constant volume lines on TS diagram which line has higher slope ? And whether slope is constant or variable ?

Last Answer : Constant volume line. Slope is variable.

In a constant pressure process steam is generated from 10 bar and 0.8 dry condition till it become dry and saturated. Determine amount of heat added per kg of steam. From steam table at 10 bar Tsat = 179.9°C hf = 762.6 kl/kg, hg = 2776.2 kJ/kg

Description : In a constant pressure process steam is generated from 10 bar and 0.8 dry condition till it become dry and saturated. Determine amount of heat added per kg of steam. From steam table at 10 bar Tsat = 179.9°C hf = 762.6 kl/kg, hg = 2776.2 kJ/kg 

Last Answer : Constant pressure process Final condition of steam is dry saturated Enthalpy of dry steam = hg= hf + hfg =2776.2 KJ/Kg .Given Latent heat of vaporization = hfg = hg - hf =2776.2-762.6 =2013.6 KJ/Kg Initial condition ... hfg = 762.6+0.8 X 2013.6 =2373.48 KJ/Kg Heat added = hg-hw = 402.72 KJ/kg

The characteristic equation of gases pv = mRT holds good for (a) mono atomic gases (b) diatomic gases (c)real gases (d) ideal gases

Description : The characteristic equation of gases pv = mRT holds good for (a) mono atomic gases (b) diatomic gases (c)real gases (d) ideal gases

Last Answer : Ans: c

Ratio of actual indicated work to hypothetical indicated work in a steam engine is the (a) Indicated thermal efficiency (b) Friction factor (c) Mechanical efficiency (d) Diagram factor

Description : Ratio of actual indicated work to hypothetical indicated work in a steam engine is the (a) Indicated thermal efficiency (b) Friction factor (c) Mechanical efficiency (d) Diagram factor

Last Answer : Ans : d

Enthalpy 'H' is defined as (A) H = E - PV (B) H = F - TS (C) H - E = PV (D) None of these

Description : Enthalpy 'H' is defined as (A) H = E - PV (B) H = F - TS (C) H - E = PV (D) None of these

Last Answer : (C) H - E = PV

Pick out the correct equation relating 'F' and 'A'. (A) F = A + PV (B) F = E + A (C) F = A - TS

Description : Pick out the correct equation relating 'F' and 'A'. (A) F = A + PV (B) F = E + A (C) F = A - TS

Last Answer : (A) F = A + PV

For perfect gas a. cp – cv = R b. cp + cv = R c. cp / cv = R d. cp X cv = R Where cp & cv are specific heats at constant pressure and volume.

Description : For perfect gas a. cp – cv = R b. cp + cv = R c. cp / cv = R d. cp X cv = R Where cp & cv are specific heats at constant pressure and volume.

Last Answer : ANSWER a. CP – CV = R

An ideal gas is heated at constant volume and then expanded isothermally. Show processes on P-V & T-S diagrams.

Description : An ideal gas is heated at constant volume and then expanded isothermally. Show processes on P-V & T-S diagrams.

Last Answer : Process 1-2 : Constant volume process Process 2-3 : Constant temperature process (Isothermal process)

On the pressure-enthalpy diagram, condensation and de-superheating is represented by a horizontal line because theprocess (a) takes place at constant pressure (b) takes place at constant temperature (c) takes place at constant entropy (d) takes place at constant enthalpy

Description : On the pressure-enthalpy diagram, condensation and de-superheating is represented by a horizontal line because theprocess (a) takes place at constant pressure (b) takes place at constant temperature (c) takes place at constant entropy (d) takes place at constant enthalpy

Last Answer : Ans: a

Steam at 1000 lbf/ft^2 pressure and 300˚R has specific volume of 6.5 ft^3/lbm and a specific enthalpy of 9800 lbf-ft/lbm. Find the internal energy per pound mass of steam.  A.2500 lbf-ft/lbm  B.3300 lbf-ft/lbm  C.5400 lbf-ft/lbm  D.6900 lbf-ft/lbm Formula: h= u+ pV u= h– pV

Description : Steam at 1000 lbf/ft^2 pressure and 300˚R has specific volume of 6.5 ft^3/lbm and a specific enthalpy of 9800 lbf-ft/lbm. Find the internal energy per pound mass of steam.  A.2500 lbf-ft/lbm  B.3300 lbf-ft/lbm  C.5400 lbf-ft/lbm  D.6900 lbf-ft/lbm Formula: h= u+ pV u= h– pV

Last Answer : 3300 lbf-ft/lbm

If value of n is infinitely large in a polytropic process pV” = C, then the process is known as constant  (a) volume  (b) pressure  (c) temperature  (d) enthalpy  (e) entropy

Description : If value of n is infinitely large in a polytropic process pV” = C, then the process is known as constant  (a) volume  (b) pressure  (c) temperature  (d) enthalpy  (e) entropy

Last Answer : Answer : a

The air standard Otto cycle comprises a two constant pressure processes and two constant volume processes b two constant pressure and two constant entropy processes c. two constant volume processes and two constant entropy processes d. none of the above.

Description : The air standard Otto cycle comprises a two constant pressure processes and two constant volume processes b two constant pressure and two constant entropy processes c. two constant volume processes and two constant entropy processes d. none of the above.

Last Answer : ANSWER (c) two constant volume processes and two constant entropy processes

In which of the following cycle heat is added at constant volume? a. Otto cycle b. Diesel cycle c. Dual cycle d. Carnot cycle

Description : In which of the following cycle heat is added at constant volume? a. Otto cycle b. Diesel cycle c. Dual cycle d. Carnot cycle

Last Answer : Answer a. Otto cycle

a direct arrow is drawn from the process to the resource rectangle to represent each pending resource request: a. TS b. SP Cc. CCR d. RAG

Description : a direct arrow is drawn from the process to the resource rectangle to represent each pending resource request: a. TS b. SP Cc. CCR d. RAG

Last Answer : d. RAG

if pressure P is inversely proportional to volume (V) at constant temperature, then PV is constant (True/False)

Description : if pressure P is inversely proportional to volume (V) at constant temperature, then PV is constant (True/False)

Last Answer : if pressure P is inversely proportional to volume (V) at constant temperature, then PV is constant (True/False)

Which of the following processes are thermodynamically reversible  (a) throttling  (b) free expansion  (c) constant volume and constant pressure  (d) hyperbolic and pV = C  (e) isothermal and adiabatic.

Description : Which of the following processes are thermodynamically reversible  (a) throttling  (b) free expansion  (c) constant volume and constant pressure  (d) hyperbolic and pV = C  (e) isothermal and adiabatic.

Last Answer : Answer : e

Which of the following is not an internal combustion engine? a. petrol engine b. steam turbine c. diesel engine d. gas turbine

Description : Which of the following is not an internal combustion engine? a. petrol engine b. steam turbine c. diesel engine d. gas turbine

Last Answer : ANSWER b. steam turbine

A spark plug is used in a. petrol engine b. diesel engine c. gas engine d. steam engine

Description : A spark plug is used in a. petrol engine b. diesel engine c. gas engine d. steam engine

Last Answer : ANSWER a. petrol engine

Explain Dalton's law in respect to steam condensers.

Description : Explain Dalton's law in respect to steam condensers.

Last Answer : It states that' The pressure exerted by mixture of air and steam is equal to sum of partial pressures, which each constitute would exert, if it occupies the same volume . Mathematically, Pc ... mixture of air and steam Pa = Partial pressure of air Ps = Partial pressure of steam

State necessity of super heater in steam boilers. State advantages of economizer.

Description : State necessity of super heater in steam boilers. State advantages of economizer. 

Last Answer : Necessity of super heater in steam boilers: 1. The efficiency of the boiler is increase with the use of superheated steam. 2. It eliminates the erosion of the turbine blades. 3. It reduces ... water. 5. This unit improves the overall efficiency of the boiler by reducing the fuel consumption. 

Describe any two sources of air leak in surface condenser. Also describe effect of air leak on latent heat of steam and cooling water requirements.

Description : Describe any two sources of air leak in surface condenser. Also describe effect of air leak on latent heat of steam and cooling water requirements.

Last Answer : ✓ The main sources of air leakage found in condenser are given below: 1) There is leakage of air from atmosphere at the joint of the parts which are internally under a pressure less ... hence evaporation enthalpy of steam increases therefore more amount of cooling water required in the condenser. 

Describe four losses in steam turbines in 1/ 2 sentences each.

Description : Describe four losses in steam turbines in 1/ 2 sentences each.

Last Answer : Energy losses in steam turbines (i) Residual velocity loss- The steam leaves the turbine with a certain absolute velocity which results in loss of KE. This loss is about 10 to 12% .It ... are heavily insulated to reduce the heat loss to surroundings by radiation and so these losses are negligible 

Comment on Mach number of steam in impulse and reaction turbines.

Description : Comment on Mach number of steam in impulse and reaction turbines. 

Last Answer : Mach number, in fluid mechanics, ratio of the velocity of a fluid to the velocity of sound in that fluid. Mach numbers less than one indicate subsonic flow; those greater than one, supersonic flow.

In a boiler enthalpy of water supplied was 2000 kJ/kg. Enthalpy being added by fuel combustion is 3200 kJ/kg. Using first law of thermodynamics, find amount of heat supplied if steam generation rate is 10 tons per hour.

Description : In a boiler enthalpy of water supplied was 2000 kJ/kg. Enthalpy being added by fuel combustion is 3200 kJ/kg. Using first law of thermodynamics, find amount of heat supplied if steam generation rate is 10 tons per hour.

Last Answer : Heat supplied Q = m (h2-h1) …….(Steady flow energy equation for boiler) ; h2=3200 KJ/kg h1=2000 KJ/kg m = 10 Tons /hour = (10 x 1000)/3600 kg/sec = 2.77 Kg/sec Q = 2.77(3200-2000) = 3324 KJ/sec heat supplied for 10 Tons/hr steam generation

In sensible cooling process the relative humidity: A. decreases B. increases C. remains constant D. none of the above

Description : In sensible cooling process the relative humidity: A. decreases B. increases C. remains constant D. none of the above

Last Answer : ANSWER : B

Humidification is the process of addition moisture in air at A. constant wet bulb temperature B. constant dry bulb temperature C. constant latent heat D. none of the above

Description : Humidification is the process of addition moisture in air at A. constant wet bulb temperature B. constant dry bulb temperature C. constant latent heat D. none of the above

Last Answer : ANSWER : B

Which of the following statement is true? A. the chart is plotted for pressure equal to 760mm Hg B. the constant wbt line represents adiabatic saturation process C. the constant wbt line coincides with constant enthalpy line D. all of the mentioned

Description : Which of the following statement is true? A. the chart is plotted for pressure equal to 760mm Hg B. the constant wbt line represents adiabatic saturation process C. the constant wbt line coincides with constant enthalpy line D. all of the mentioned

Last Answer : ANSWER : D

In a single stage reciprocating air compressor, the work done on air to compressor is from suction pressure to delivery pressure will be minimum when the compression is A. Isothermal process B. Adiabatic process C. Polytropic process D. Constant pressure process.

Description : In a single stage reciprocating air compressor, the work done on air to compressor is from suction pressure to delivery pressure will be minimum when the compression is A. Isothermal process B. Adiabatic process C. Polytropic process D. Constant pressure process.

Last Answer : ANSWER : A

The lower horizontal line of the refrigeration cycle plotted on pressure-enthalpy-diagram represents (a) condensation of the refrigerant vapour (b) evaporation of the refrigerant liquid (c) compression of the refrigerant vapour (d) metering of the refrigerant liquid

Description : The lower horizontal line of the refrigeration cycle plotted on pressure-enthalpy-diagram represents (a) condensation of the refrigerant vapour (b) evaporation of the refrigerant liquid (c) compression of the refrigerant vapour (d) metering of the refrigerant liquid

Last Answer : Ans: b

The area of actual indicator diagram on an air compressor as compared to area of ideal indicator diagram is A. Less B. More C. Same D. Unpredictable

Description : The area of actual indicator diagram on an air compressor as compared to area of ideal indicator diagram is A. Less B. More C. Same D. Unpredictable

Last Answer : ANSWER : B

Find ∫ for steam at 100 psia and 600°F.If h = 1329.6 and v = 6.216  a. 1214 Btu / lb  b. 1234 Btu /lb  c. 1342 Btu / lb  d. 1324 Btu /lb formula: ∫ = h– pv/ J

Description : Find ∫ for steam at 100 psia and 600°F.If h = 1329.6 and v = 6.216  a. 1214 Btu / lb  b. 1234 Btu /lb  c. 1342 Btu / lb  d. 1324 Btu /lb formula: ∫ = h– pv/ J

Last Answer : 1214Btu / lb

An isentropic process is the one, in which (A) pv = constant (B) pv r= constant (C) pv r = constant, and process is reversible (D) None of these

Description : An isentropic process is the one, in which (A) pv = constant (B) pv r= constant (C) pv r = constant, and process is reversible (D) None of these

Last Answer : (C) pv r = constant, and process is reversible

Which of the following is not correct for a reversible adiabatic process? (A) TV γ-1 = constant (B) p 1-γ .T Y = constant (C) PV γ = constant (D) None of these

Description : Which of the following is not correct for a reversible adiabatic process? (A) TV γ-1 = constant (B) p 1-γ .T Y = constant (C) PV γ = constant (D) None of these

Last Answer : (D) None of these

In polytropic process (PV n = constant), if n = 1; it means a/an __________ process. (A) Adiabatic (B) Reversible (C) Isothermal (D) None of these

Description : In polytropic process (PV n = constant), if n = 1; it means a/an __________ process. (A) Adiabatic (B) Reversible (C) Isothermal (D) None of these

Last Answer : (C) Isothermal

Accumulators should have adequate volume to store refrigerant charge at least (a) 10% (b) 25% (c) 50% (d) 75%

Description : Accumulators should have adequate volume to store refrigerant charge at least (a) 10% (b) 25% (c) 50% (d) 75%

Last Answer : Ans: c

Clapeyron equation is a relation between (a) temperature, pressure and enthalpy (b) specific volume and enthalpy (c) temperature and enthalpy (d) temperature, pressure, specific vapour and enthalpy.

Description : Clapeyron equation is a relation between (a) temperature, pressure and enthalpy (b) specific volume and enthalpy (c) temperature and enthalpy (d) temperature, pressure, specific vapour and enthalpy.

Last Answer : Ans: D

The volume of standard air is _____ m3/kg of dry air. a. 0.533 b. 0.633 c. 0.733 d. 0.833 e. 0.933

Description : The volume of standard air is _____ m3/kg of dry air. a. 0.533 b. 0.633 c. 0.733 d. 0.833 e. 0.933

Last Answer : Answer: D

The specific volume of air is expressed as the volume of: a. 1 kg of air at 101.325 kPa in cm3 b. 0.833 kg of air at standard pressure and temperature in m3 c. 1 kg of air at 101.325 kPa and 21 degrees Celsius in m3 d. 1 g of air occupied at any temperature and pressure e. 1 kg of air, regardless of temperature and pressure

Description : The specific volume of air is expressed as the volume of: a. 1 kg of air at 101.325 kPa in cm3 b. 0.833 kg of air at standard pressure and temperature in m3 c. 1 kg of air at 101.325 ... d. 1 g of air occupied at any temperature and pressure e. 1 kg of air, regardless of temperature and pressure

Last Answer : Answer: C

Standard air is the: a. Mass of 1 cubic meter of dry air at 20°C and atmospheric pressure b. Mass of a cubic meter of air at atmospheric conditions c. Volume of air at ambient temperature and atmospheric pressure d. Volume of 1 kg of dry air at 21°C and atmospheric pressure at sea level or 101.325 kPa e. Volume of 1 kg of air at 15°C and 100 kPa

Description : Standard air is the: a. Mass of 1 cubic meter of dry air at 20°C and atmospheric pressure b. Mass of a cubic meter of air at atmospheric conditions c. Volume of air at ambient temperature and atmospheric pressure ... pressure at sea level or 101.325 kPa e. Volume of 1 kg of air at 15°C and 100 kPa

Last Answer : Answer: D

The actual volume of fresh charge admitted in 4-stroke petrol engine is A. equal to stroke volume B. equal stroke volume and clearance volume C. less than stroke volume D. more than stroke volume

Description : The actual volume of fresh charge admitted in 4-stroke petrol engine is A. equal to stroke volume B. equal stroke volume and clearance volume C. less than stroke volume D. more than stroke volume

Last Answer : ANSWER : C

Super charging by Roots blower means A. the cost will be very high B. the life would be short C. creating balancing problems at high speeds D. handling large volume of air without being too bulky

Description : Super charging by Roots blower means A. the cost will be very high B. the life would be short C. creating balancing problems at high speeds D. handling large volume of air without being too bulky

Last Answer : ANSWER : D

The accumulation of carbon in a cylinder results in increase of A. clearance volume B. volumetric efficiency C. ignition time D. effective compression ratio

Description : The accumulation of carbon in a cylinder results in increase of A. clearance volume B. volumetric efficiency C. ignition time D. effective compression ratio

Last Answer : ANSWER : D

An engine indicator is used to determine the following A. Speed B. Temperature C. M.E.P D. Volume of cylinder

Description : An engine indicator is used to determine the following A. Speed B. Temperature C. M.E.P D. Volume of cylinder

Last Answer : ANSWER : C

In compression ignition (CI) engine, the compression ratio is a. Cylinder volume / Clearance volume b. Swept Volume / Cylinder Volume c. Clearance volume / Cylinder volume d. Cylinder volume / Swept volume (Ans:a)

Description : In compression ignition (CI) engine, the compression ratio is a. Cylinder volume / Clearance volume b. Swept Volume / Cylinder Volume c. Clearance volume / Cylinder volume d. Cylinder volume / Swept volume (Ans:a)

Last Answer : In two stroke engine there is one power stroke in _____ of crankshaft rotation. a. 90° b. 180° c. 270° d. 360° (Ans:d)

The _____________ sensor, monitors mass or volume of air flowing into the intake manifold for adjusting the quantity of fuel. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Description : The _____________ sensor, monitors mass or volume of air flowing into the intake manifold for adjusting the quantity of fuel. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Last Answer : Answer: c Explanation: The air flow sensor, monitors mass or volume of air flowing into the intake manifold for adjusting the quantity of fuel while exhaust gas senor senses the amount of oxygen in the engine exhaust and calculates air-fuel ratio.

The heating value per unit volume of hydrogen gas is less than ______________ that of air. a) 1/12th b) 1/10th c) 2/3rd d) 1/3rd

Description : The heating value per unit volume of hydrogen gas is less than ______________ that of air. a) 1/12th b) 1/10th c) 2/3rd d) 1/3rd

Last Answer : Answer: d Explanation: None

If the performance of diesel engine of different sizes, cylinder dimensions and power rating are to be compared, which of the following parameters can be used for such comparison? (a) Swept volume (b) Air fuel ratio (c) Specific brake fuel consumption (d) Volumetric efficiency

Description : If the performance of diesel engine of different sizes, cylinder dimensions and power rating are to be compared, which of the following parameters can be used for such comparison? (a) Swept volume (b) Air fuel ratio (c) Specific brake fuel consumption (d) Volumetric efficiency

Last Answer : Ans :c