Comment on Mach number of steam in impulse and reaction turbines.

Comment on Mach number of steam in impulse and reaction turbines. 
by

1 Answer

Answer :

Mach number, in fluid mechanics, ratio of the velocity of a fluid to the velocity of sound in that fluid. Mach numbers less than one indicate subsonic flow; those greater than one, supersonic flow.
by

Related questions

Describe four losses in steam turbines in 1/ 2 sentences each.

Description : Describe four losses in steam turbines in 1/ 2 sentences each.

Last Answer : Energy losses in steam turbines (i) Residual velocity loss- The steam leaves the turbine with a certain absolute velocity which results in loss of KE. This loss is about 10 to 12% .It ... are heavily insulated to reduce the heat loss to surroundings by radiation and so these losses are negligible 

Supercharging is essential in A. aircraft engines B. petrol engines C. gas turbines D. diesel engines

Description : Supercharging is essential in A. aircraft engines B. petrol engines C. gas turbines D. diesel engines

Last Answer : ANSWER : A

Ratio of actual indicated work to hypothetical indicated work in a steam engine is the (a) Indicated thermal efficiency (b) Friction factor (c) Mechanical efficiency (d) Diagram factor

Description : Ratio of actual indicated work to hypothetical indicated work in a steam engine is the (a) Indicated thermal efficiency (b) Friction factor (c) Mechanical efficiency (d) Diagram factor

Last Answer : Ans : d

Which of the following is not an internal combustion engine? a. petrol engine b. steam turbine c. diesel engine d. gas turbine

Description : Which of the following is not an internal combustion engine? a. petrol engine b. steam turbine c. diesel engine d. gas turbine

Last Answer : ANSWER b. steam turbine

A spark plug is used in a. petrol engine b. diesel engine c. gas engine d. steam engine

Description : A spark plug is used in a. petrol engine b. diesel engine c. gas engine d. steam engine

Last Answer : ANSWER a. petrol engine

Explain Dalton's law in respect to steam condensers.

Description : Explain Dalton's law in respect to steam condensers.

Last Answer : It states that' The pressure exerted by mixture of air and steam is equal to sum of partial pressures, which each constitute would exert, if it occupies the same volume . Mathematically, Pc ... mixture of air and steam Pa = Partial pressure of air Ps = Partial pressure of steam

State necessity of super heater in steam boilers. State advantages of economizer.

Description : State necessity of super heater in steam boilers. State advantages of economizer. 

Last Answer : Necessity of super heater in steam boilers: 1. The efficiency of the boiler is increase with the use of superheated steam. 2. It eliminates the erosion of the turbine blades. 3. It reduces ... water. 5. This unit improves the overall efficiency of the boiler by reducing the fuel consumption. 

Represent constant volume process on PV & TS diagram for steam.

Description : Represent constant volume process on PV & TS diagram for steam.

Last Answer : Represent constant volume process on PV & TS diagram for steam.

Describe any two sources of air leak in surface condenser. Also describe effect of air leak on latent heat of steam and cooling water requirements.

Description : Describe any two sources of air leak in surface condenser. Also describe effect of air leak on latent heat of steam and cooling water requirements.

Last Answer : ✓ The main sources of air leakage found in condenser are given below: 1) There is leakage of air from atmosphere at the joint of the parts which are internally under a pressure less ... hence evaporation enthalpy of steam increases therefore more amount of cooling water required in the condenser. 

In a constant pressure process steam is generated from 10 bar and 0.8 dry condition till it become dry and saturated. Determine amount of heat added per kg of steam. From steam table at 10 bar Tsat = 179.9°C hf = 762.6 kl/kg, hg = 2776.2 kJ/kg

Description : In a constant pressure process steam is generated from 10 bar and 0.8 dry condition till it become dry and saturated. Determine amount of heat added per kg of steam. From steam table at 10 bar Tsat = 179.9°C hf = 762.6 kl/kg, hg = 2776.2 kJ/kg 

Last Answer : Constant pressure process Final condition of steam is dry saturated Enthalpy of dry steam = hg= hf + hfg =2776.2 KJ/Kg .Given Latent heat of vaporization = hfg = hg - hf =2776.2-762.6 =2013.6 KJ/Kg Initial condition ... hfg = 762.6+0.8 X 2013.6 =2373.48 KJ/Kg Heat added = hg-hw = 402.72 KJ/kg

Represent generation of steam on H-S diagram. Show constant dryness fraction lines, constant temperature lines, saturated line and superheated region on the same.

Description : Represent generation of steam on H-S diagram. Show constant dryness fraction lines, constant temperature lines, saturated line and superheated region on the same.

Last Answer : Represent generation of steam on H-S diagram. Show constant dryness fraction lines, constant temperature lines, saturated line and superheated region on the same.

In a boiler enthalpy of water supplied was 2000 kJ/kg. Enthalpy being added by fuel combustion is 3200 kJ/kg. Using first law of thermodynamics, find amount of heat supplied if steam generation rate is 10 tons per hour.

Description : In a boiler enthalpy of water supplied was 2000 kJ/kg. Enthalpy being added by fuel combustion is 3200 kJ/kg. Using first law of thermodynamics, find amount of heat supplied if steam generation rate is 10 tons per hour.

Last Answer : Heat supplied Q = m (h2-h1) …….(Steady flow energy equation for boiler) ; h2=3200 KJ/kg h1=2000 KJ/kg m = 10 Tons /hour = (10 x 1000)/3600 kg/sec = 2.77 Kg/sec Q = 2.77(3200-2000) = 3324 KJ/sec heat supplied for 10 Tons/hr steam generation

In hydel power station, the motion produced in turbines is due to – (1) flow of water (2) burning of coal (3) burning of diesel (4) production of steam

Description : In hydel power station, the motion produced in turbines is due to – (1) flow of water (2) burning of coal (3) burning of diesel (4) production of steam

Last Answer : (1) flow of water Explanation: A water turbine is a rotary machine that converts kinetic energy and potential energy of water into mechanical work. Hydroelectric power comes from water at work, water in motion. To generate electricity, water must be in motion. This is kinetic (moving) energy.

Why do cylindrical Alternators operate with steam turbines?

Description : Why do cylindrical Alternators operate with steam turbines?

Last Answer : A: Steam turbines are found to operate at fairly good efficiency only at high speeds. The high speed operation of rotors tends to increase mechanical losses and so the rotors should have a ... axial length are used for Synchronous generators driven by steam turbines with either 2 or 4 poles.

In steam and gas turbines, rolling contact bearings are used. a) True b) False

Description : In steam and gas turbines, rolling contact bearings are used. a) True b) False

Last Answer : b) False

Water is useful for (A) Running hydroelectric turbines (B) Floating the boats and ships (C) Providing steam for running locomotives (D) All the above

Description : Water is useful for (A) Running hydroelectric turbines (B) Floating the boats and ships (C) Providing steam for running locomotives (D) All the above

Last Answer : Answer: Option D

What Are The Two Basic Types Of Steam Turbines?

Description : What Are The Two Basic Types Of Steam Turbines?

Last Answer : 1. Impulse type. 2. Reaction type.

Steam is regularly used for propulsion (as a driving force) in applications such as ________ turbines. • Gas turbine • Steam turbine • Water turbine

Description : Steam is regularly used for propulsion (as a driving force) in applications such as ________ turbines. • Gas turbine • Steam turbine • Water turbine

Last Answer : • Steam turbine

Boiler efficiency is a measure of how effectively _______ energy in fuel is converted into heat energy in steam going to the turbines A Chemical energy B Heat energy C Thermal energy D All of the above

Description : Boiler efficiency is a measure of how effectively _______ energy in fuel is converted into heat energy in steam going to the turbines A Chemical energy B Heat energy C Thermal energy D All of the above

Last Answer : A Chemical energy

How can steam turbines be classified? By the action of steam:

Description : How can steam turbines be classified? By the action of steam:

Last Answer : 1. Impulse. 2. Reaction. 3. Impulse and reaction combined

How can problems of "excessive vibration or noise" due to piping strain be avoided on steam turbines?

Description : How can problems of "excessive vibration or noise" due to piping strain be avoided on steam turbines?

Last Answer : 1. The inlet as well as exhaust steam lines should be firmly supported to avoid strains from being imposed on the turbine. 2. Adequate allowance should be made for expansion of steam pipes due to heat.

What are the two basic types of steam turbines?

Description : What are the two basic types of steam turbines?

Last Answer : 1. Impulse type. 2. Reaction type

In hydel power station, the motion produced in turbines is due to (1) flow of water (2) burning of coal (3) burning of diesel (4) production of steam

Description : In hydel power station, the motion produced in turbines is due to (1) flow of water (2) burning of coal (3) burning of diesel (4) production of steam

Last Answer : flow of water

With neat sketch describe working of reaction turbine.

Description : With neat sketch describe working of reaction turbine.

Last Answer : Working principle of reaction turbine- -A turbine in which steam pressure decreases gradually while expanding through the moving as well as through the fixed blade is known as reaction turbine. -In pure ... the steam to leave the moving blade as higher velocity than as which it entered.

Explain the principle of working of impulse steam turbine.

Description : Explain the principle of working of impulse steam turbine. 

Last Answer : When steam enters the turbine it suffers a change in direction and momentum, which gives rise to the rotation of the turbine. There will be no drop in pressure in impulse steam turbine.  

Explain principle of working of Impulse steam turbine with neat sketch.

Description : Explain principle of working of Impulse steam turbine with neat sketch.

Last Answer : Construction: Impulse turbine is simpler, less expensive and does not need to be pressure proof. It can operate with any pressure stream but is considerably less efficient. Impulse turbine consist of one ... by one set of moving blade ring as shown in Fig. for a single stage impulse turbine.

The transfer of energy for reaction turbines is based on _______

Description : The transfer of energy for reaction turbines is based on _______ A) Newton’s first law B) Newton’s second law C) Newton’s third law D) All the above

Last Answer : The transfer of energy for reaction turbines is based on Newton’s third law

Octane number of gasoline is obtained by comparing the performance of the engine when running on a mixture of the following hydrocarbons A. ethane and methane B. normal heptane and iso-octane C. iso-heptane and octane D. iso-octane and TEL

Description : Octane number of gasoline is obtained by comparing the performance of the engine when running on a mixture of the following hydrocarbons A. ethane and methane B. normal heptane and iso-octane C. iso-heptane and octane D. iso-octane and TEL

Last Answer : ANSWER : B

A fuel of cetane number 40 has the same ignition quality as a mixture of a) 40% cetane and 60% alpha methyl naphthalene b) 40% alpha methyl naphthalene and 60% cetane c) 40% petrol and 60% diesel d) 40% diesel and 60% petrol

Description : A fuel of cetane number 40 has the same ignition quality as a mixture of a) 40% cetane and 60% alpha methyl naphthalene b) 40% alpha methyl naphthalene and 60% cetane c) 40% petrol and 60% diesel d) 40% diesel and 60% petrol

Last Answer : Answer: a Explanation: A fuel of cetane number 40 has the same ignition quality as a mixture of 40% cetane and 60% alpha methyl naphthalene as cetane number is counted on cetane percentage.

A mixture containing 65% of iso-octane and 35% of normal heptane will have a) cetane number 65 b) octane number 65 c) cetane number 35 d) octane number 35

Description : A mixture containing 65% of iso-octane and 35% of normal heptane will have a) cetane number 65 b) octane number 65 c) cetane number 35 d) octane number 35

Last Answer : Answer: b Explanation: A mixture containing 65% of iso-octane and 35% of normal heptane will have octane number 65 as octane number is the number percentage containing iso-octane.

A fuel of an octane number rating of 75 matches in knocking intensity as a mixture of a) 75% iso-octane and 25% normal heptane b) 75% normal heptane and 25% iso-octane c) 75% petrol and 25% diesel d) 75% diesel and 25% petrol

Description : A fuel of an octane number rating of 75 matches in knocking intensity as a mixture of a) 75% iso-octane and 25% normal heptane b) 75% normal heptane and 25% iso-octane c) 75% petrol and 25% diesel d) 75% diesel and 25% petrol

Last Answer : Answer: a Explanation: None.

The normal heptane(C7H16) is given a rating of ____________ octane number. a) 0 b) 50 c) 100 d) 120

Description : The normal heptane(C7H16) is given a rating of ____________ octane number. a) 0 b) 50 c) 100 d) 120

Last Answer : Answer: a Explanation: None.

By higher octane number of SI fuel, it is meant that the fuel has (a) Higher heating value (b) Higher flash point (c) Lower volatility (d) Longer ignition delay

Description : By higher octane number of SI fuel, it is meant that the fuel has (a) Higher heating value (b) Higher flash point (c) Lower volatility (d) Longer ignition delay

Last Answer : Ans : d

Cetane number of petrol is around a. 10 b. 15-20 c. 35 d. 55-70

Description : Cetane number of petrol is around a. 10 b. 15-20 c. 35 d. 55-70

Last Answer : ANSWER b. 15-20

Cetane number is a measure of a. ignition quality b. addition in fuel c. calorific value of fuel d. viscosity of the fuel

Description : Cetane number is a measure of a. ignition quality b. addition in fuel c. calorific value of fuel d. viscosity of the fuel

Last Answer : ANSWER a. ignition quality

Octane number of petrol normally used in petrol engines is of the order of a. 20-30 b. 40-60 c. 60-70 d. 80-90

Description : Octane number of petrol normally used in petrol engines is of the order of a. 20-30 b. 40-60 c. 60-70 d. 80-90

Last Answer : ANSWER d. 80-90

The tendency of a diesel engine to knock increases if a. engine speed is increased b. engine power is increased c. cetane number of the fuel is increased d. compression ratio is increased

Description : The tendency of a diesel engine to knock increases if a. engine speed is increased b. engine power is increased c. cetane number of the fuel is increased d. compression ratio is increased

Last Answer : ANSWER d. compression ratio is increased

Ignition quality of diesel is expressed by a. octane number b. cetane number c. calorific value d. carbon content

Description : Ignition quality of diesel is expressed by a. octane number b. cetane number c. calorific value d. carbon content

Last Answer : ANSWER b. cetane number

For the best results of efficient combustion, high speed diesel engines need an approximate cetane number of a. 100 b. 50 c. 10 d. 5

Description : For the best results of efficient combustion, high speed diesel engines need an approximate cetane number of a. 100 b. 50 c. 10 d. 5

Last Answer : ANSWER b. 50

Ignition quality of petrol is expressed by a. Octane number b. cetane number c. calorific value d. self-ignition temperature

Description : Ignition quality of petrol is expressed by a. Octane number b. cetane number c. calorific value d. self-ignition temperature

Last Answer : ANSWER a. Octane number

Classification of air compressor

Description : Classification Of Air Compressor

Last Answer : Air compressors are classified in several different ways, depending on the specific characteristics and features of the compressor. Here are a few common ways that air compressors are classified: ... range of sizes and capacities, from small, portable units to large, industrial-sized compressors.

The freon group of refrigerants are (a) halo-carbon refrigerants (b) azeotrope refrigerants (c) inorganic refrigerants (d) hydro-carbon refrigerants

Description : The freon group of refrigerants are (a) halo-carbon refrigerants (b) azeotrope refrigerants (c) inorganic refrigerants (d) hydro-carbon refrigerants

Last Answer : Ans: a

The formation of frost on cooling coils in a refrigerator (a) increases heat transfer (b) improves C.O.P. of the system (c) increases power consumption (d) reduces power consumption

Description : The formation of frost on cooling coils in a refrigerator (a) increases heat transfer (b) improves C.O.P. of the system (c) increases power consumption (d) reduces power consumption

Last Answer : Ans: c

For ammonia refrigerating systems, the tubes of a shell and tube condenser are made of (a) copper (b) aluminium (c) steel (d) brass

Description : For ammonia refrigerating systems, the tubes of a shell and tube condenser are made of (a) copper (b) aluminium (c) steel (d) brass

Last Answer : Ans: c

In milk chilling plant, the usual secondary refrigerant is (a)ammonia (b)sodium silicate (c) glycol (d) brine

Description : In milk chilling plant, the usual secondary refrigerant is (a)ammonia (b)sodium silicate (c) glycol (d) brine

Last Answer : Ans: d

In a refrigeration cycle, the super heating……..C.O.P (a)decreases (b)does not change (c) increases (d)none of the above

Description : In a refrigeration cycle, the super heating……..C.O.P (a)decreases (b)does not change (c) increases (d)none of the above

Last Answer : Ans: a

The condition of refrigerant before entering the expansion or throttle valve, in a vapour compression system (a) dry vapour (b) wet vapour (c)liquid-vapour mixture (d) high pressure saturated liquid

Description : The condition of refrigerant before entering the expansion or throttle valve, in a vapour compression system (a) dry vapour (b) wet vapour (c)liquid-vapour mixture (d) high pressure saturated liquid

Last Answer : Ans: d

Air refrigeration cycle is used in (a) domestic refrigerators (b) gas liquefaction (c)commercial refrigerators (d) Chillers

Description : Air refrigeration cycle is used in (a) domestic refrigerators (b) gas liquefaction (c)commercial refrigerators (d) Chillers

Last Answer : Ans: b

The characteristic equation of gases pv = mRT holds good for (a) mono atomic gases (b) diatomic gases (c)real gases (d) ideal gases

Description : The characteristic equation of gases pv = mRT holds good for (a) mono atomic gases (b) diatomic gases (c)real gases (d) ideal gases

Last Answer : Ans: c

The change in evaporator temperature in a refrigeration cycle, as compared to change in condenser temperature, influences the value of C.O.P. (a) more (b) less (c) equally. (d) unpredictable

Description : The change in evaporator temperature in a refrigeration cycle, as compared to change in condenser temperature, influences the value of C.O.P. (a) more (b) less (c) equally. (d) unpredictable

Last Answer : Ans: a