What terms are not an integral part of the electric pallet jack equipment but is used to hold a load or loads?

What terms are not an integral part of the electric pallet jack equipment but is used to hold a load or loads?
by

1 Answer

Answer :

What is the answer ?
by

Related questions

On average, how much of a load can a pallet jack carry?

Description : On average, how much of a load can a pallet jack carry?

Last Answer : Pallet jacks can carry up to 8000 lbs of weight. On average however they carry around 2500-5000 lbs of weight.

How to Use a Pallet Jack on Ramps?

Description : How to Use a Pallet Jack on Ramps?

Last Answer : As you may already be aware, a pallet jack is a relatively cheap device that allows you to lift up and move objects that are on a pallet, and it may otherwise be known as a pallet truck. It is ... materials in a factory, a warehouse, a lab or a store, you should wear steel toe boots and protecti

How to Buy a Pallet Jack?

Description : How to Buy a Pallet Jack?

Last Answer : A pallet jack is a rolling device that is used to lift up apallet. The pallet jack can then be used to transport supplies andequipment within a warehousing facility. Pallet jacks carry andlift ... best help them complete theirdaily tasks. Take in to consideration also the size and weight ofthe b

How much are one of those Hand Pallet Jack?

Description : How much are one of those Hand Pallet Jack?

Last Answer : Pallet jacks range anywhere in price from a couple hundred dollars to a couple thousand dollars depending on what size you need. I have found them at global for $169 though. Here is the link: www.globalindustrial. ... . They range from $150.00 and up for a manual one to $6000.00 for a electric one.

Can I rent a pallet jack from Home Depot?

Description : Can I rent a pallet jack from Home Depot?

Last Answer : Pallet jacks are typically not available for rent through Home Depot. Chances are that if you check Craigslist you'll be able to find exactly what you are looking for.

What is the weight limit on the average pallet jack?

Description : What is the weight limit on the average pallet jack?

Last Answer : The weight limit is often around 800 pounds. You could buy some that can do more.

What is a multiton pallet jack?

Description : What is a multiton pallet jack?

Last Answer : Multiton is the name of a company that sold equipment such as pallet jacks. They are no longer doing business under that name. You can now find this equipment under the name Multiton name Jungheinrich.

What is the average weight rating on a small pallet jack?

Description : What is the average weight rating on a small pallet jack?

Last Answer : You probably won't have an issue moving your supplies. Even the smallest of pallet jacks are rated to handle WELL over 2000 pounds.

In the CNC machine which device used to hold the workpiece? a.Automatic pallet changer b.Automatic work part positioner c.A & B both d.None of the above

Description : In the CNC machine which device used to hold the workpiece? a.Automatic pallet changer b.Automatic work part positioner c.A & B both d.None of the above

Last Answer : c.A & B both

Which is an integral part of any microcomputer system and its primary purpose is to hold program and data: a. Memory unit b. Register unit c. A and B d. None of these

Description : Which is an integral part of any microcomputer system and its primary purpose is to hold program and data: a. Memory unit b. Register unit c. A and B d. None of these

Last Answer : a. Memory unit

How much can a pallet rack hold?

Description : How much can a pallet rack hold?

Last Answer : The weight a pallet rack can hold is dependent on the size of the beams and uprights. A standard 3.5"x96" beam holds about 4100 pounds per pair. A 6"x144" beam holds about 6000lbs per pair. You need to find the exact size and the manufacturer and contact them or a local dealer.

From the following which is the types of Automated Guided Vehicle (AGV). a.Driver less train b.Pallet trucks c.Unit load carriers d.All of the above

Description : From the following which is the types of Automated Guided Vehicle (AGV). a.Driver less train b.Pallet trucks c.Unit load carriers d.All of the above

Last Answer : d.All of the above

In wht order should pallet loading multi stop load?

Description : In wht order should pallet loading multi stop load?

Last Answer : Need answer

How many kraft paper bags on a pallet and how many kraft paper bags can we load on a container 40 foot?

Description : How many kraft paper bags on a pallet and how many kraft paper bags can we load on a container 40 foot?

Last Answer : What is the answer ?

What is the max weight load for a wooden pallet?

Description : What is the max weight load for a wooden pallet?

Last Answer : most pallets are rated for 4000-6000 lbs (2 to 3 tons) most can handle more than that but it's not recommended to overload the pallet.

Which equation will hold good for a magnetic material? a) Line integral of H is zero b) Surface integral of H is zero c) Line integral of B is zero d) Surface integral of B is zero

Description : Which equation will hold good for a magnetic material? a) Line integral of H is zero b) Surface integral of H is zero c) Line integral of B is zero d) Surface integral of B is zero

Last Answer : d) Surface integral of B is zero

Pick out the correct statement. (A) For identical gas flow rates, less pressure drop occurs through a plate tower than through a packed tower (B) Plate column can handle greater liquid loads without flooding than packed column, but the liquid hold up is more in the case of plate column (C) For the same duty, plate columns weigh less than packed columns (D) All (A), (B) and (C)

Description : Pick out the correct statement. (A) For identical gas flow rates, less pressure drop occurs through a plate tower than through a packed tower (B) Plate column can handle greater liquid loads without flooding than packed ... duty, plate columns weigh less than packed columns (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

If a soil undergoes a change in shape and volume by application of external loads over it, but recovers its shape and volume immediately after removal of the load, the property of the soil is said to be (A) Resilience of soils (B) Elasticity of soils (C) Compressibility of soils (D) None of these

Description : If a soil undergoes a change in shape and volume by application of external loads over it, but recovers its shape and volume immediately after removal of the load, the property of the soil is said to ... Resilience of soils (B) Elasticity of soils (C) Compressibility of soils (D) None of these

Last Answer : Answer: Option B

Assertion A : The load factor for live load is greater than that for dead load. Reason R : The live loads are more uncertain than dead loads. Select your answer based on the coding system given below: (A) Both A and R is true and R is the correct explanation of A (B) Both A and R is true but R is not the correct explanation of A (C) A is true but R is false (D) A is false but R is true

Description : Assertion A : The load factor for live load is greater than that for dead load. Reason R : The live loads are more uncertain than dead loads. Select your answer based on the coding system given below: (A) Both A ... explanation of A (C) A is true but R is false (D) A is false but R is true

Last Answer : Answer: Option A

A beam is a structural member which is subjected to (a) Axial tension or compression (b) Transverse loads and couples (c) Twisting moment (d) No load, but its axis should be horizontal and x-section rectangular or circular

Description : A beam is a structural member which is subjected to (a) Axial tension or compression (b) Transverse loads and couples (c) Twisting moment (d) No load, but its axis should be horizontal and x-section rectangular or circular

Last Answer : b) Transverse loads and couples

Which of the following is/are correct? 2. Broad guage railway engines - Varanasi 3. Electric locomotives - Bhopal 4. Integral Coach Factory - Kolkata (a) 1 (b) 2 (c) 3 (d) 1, 2 and 3

Description : Which of the following is/are correct? 2. Broad guage railway engines - Varanasi 3. Electric locomotives - Bhopal 4. Integral Coach Factory - Kolkata (a) 1 (b) 2 (c) 3 (d) 1, 2 and 3

Last Answer : Ans: (b)

Which of the following is/are correct? 1. Broad guage railway engines- Varanasi 2. Electric locomotives - Bhopal 3. Integral Coach Factory - Kolkata (a) 1 (b) 2 (c) 3 (d) 1, 2 and 3

Description : Which of the following is/are correct? 1. Broad guage railway engines- Varanasi 2. Electric locomotives - Bhopal 3. Integral Coach Factory - Kolkata (a) 1 (b) 2 (c) 3 (d) 1, 2 and 3

Last Answer : Ans: (d)

The line integral of the electric field intensity is a) Mmf b) Emf c) Electric potential d) Magnetic potential

Description : The line integral of the electric field intensity is a) Mmf b) Emf c) Electric potential d) Magnetic potential

Last Answer : b) Emf

Gauss law for electric field uses surface integral. State True/False a) True b) False

Description : Gauss law for electric field uses surface integral. State True/False a) True b) False

Last Answer : a) True

The work-electric field relation is given by a) Volume integral b) Surface integral c) Line integral d) Relation impossible

Description : The work-electric field relation is given by a) Volume integral b) Surface integral c) Line integral d) Relation impossible

Last Answer : c) Line integral

The full torque electric brake on an electric cargo winch functions to _____________. A. act as a backup brake in the event the mechanical brake should fail B. automatically hold the load as soon as current to the machine is shut off C. automatically govern the lowering speed of the load D. automatically govern the hoisting speed of the load

Description : The full torque electric brake on an electric cargo winch functions to _____________. A. act as a backup brake in the event the mechanical brake should fail B. automatically hold the load ... automatically govern the lowering speed of the load D. automatically govern the hoisting speed of the load

Last Answer : Answer: B

Mr. and Mrs. Smith were walking home from the shopping mall with their purchases when Mr. Smith began to complain that his load was too heavy. Mrs. Smith turned to her husband and said, 'I don't know what you're complaining about because if you gave me one of your parcels, I would have twice as many as you and if I gave you just one of mine, we would have equal loads.' How many parcels was each carrying? -Riddles

Description : Mr. and Mrs. Smith were walking home from the shopping mall with their purchases when Mr. Smith began to complain that his load was too heavy. Mrs. Smith turned to her husband and said, 'I don't ... gave you just one of mine, we would have equal loads.' How many parcels was each carrying? -Riddles

Last Answer : Mrs. Smith was carrying seven parcels and Mr. Smith was carrying five.

If two electrical loads are connected in parallel with each other and each load draw 6 amps what is the current of the circuit?

Description : If two electrical loads are connected in parallel with each other and each load draw 6 amps what is the current of the circuit?

Last Answer : 12 Amperes is.

Two paralleled alternators are operating near rated load. If one trips out mechanically, which of the listed actions should be taken FIRST? A. Restart the tripped machine immediately. B. Strip the board of all non-vital circuits. C. Start the emergency generator. D. Transfer all vital loads to the emergency bus.

Description : Two paralleled alternators are operating near rated load. If one trips out mechanically, which of the listed actions should be taken FIRST? A. Restart the tripped machine immediately. B. Strip the board ... circuits. C. Start the emergency generator. D. Transfer all vital loads to the emergency bus.

Last Answer : Answer: B

The purpose of 'R6' in the winch circuit shown in the illustration is to _______________. EL-0102 A. maintain dry conditions within the winch brake box B. keep the series field current at a low value during 'fourth and fifth point lowering' C. act as the armature dynamic braking load to assist the winch in stopping D. limit the armature current during lowering operation with heavy loads

Description : The purpose of 'R6' in the winch circuit shown in the illustration is to _______________. EL-0102 A. maintain dry conditions within the winch brake box B. keep the series field current at ... to assist the winch in stopping D. limit the armature current during lowering operation with heavy loads

Last Answer : Answer: C

The operator of electrical motors should keep a constant check on the loads they carry because _____________. A. low loads necessitate frequent insulation cleaning B. exceeding nameplate values shortens useful life C. energy is wasted if full loading is not utilized D. power factor correction methods are load dependent

Description : The operator of electrical motors should keep a constant check on the loads they carry because _____________. A. low loads necessitate frequent insulation cleaning B. exceeding nameplate values shortens ... wasted if full loading is not utilized D. power factor correction methods are load dependent

Last Answer : Answer: B

The total power consumed in a parallel circuit is __________. A. the sum of the powers used in each load (resistor) divided by the number of loads B. always less than the power used in the smallest load C. the sum of the powers used in each individual load D. never more than the power used in the largest load

Description : The total power consumed in a parallel circuit is __________. A. the sum of the powers used in each load (resistor) divided by the number of loads B. always less than the power used in the smallest ... of the powers used in each individual load D. never more than the power used in the largest load

Last Answer : Answer: C

The total power used up in a series circuit is ___________. A. the sum of the powers used in each load (resistor) divided by the number of loads B. the sum of the powers used in each load C. always less than the power used in the smallest load D. never more than the power used in largest load

Description : The total power used up in a series circuit is ___________. A. the sum of the powers used in each load (resistor) divided by the number of loads B. the sum of the powers used in each load C. always less than the power used in the smallest load D. never more than the power used in largest load

Last Answer : Answer: B

Tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads and the ratio of these being greater than unity (d) both radial and axial loads and the ratio of these being less than unity

Description : Tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads and the ratio of these being greater than unity (d) both radial and axial loads and the ratio of these being less than unity

Last Answer : (c) both radial and axial loads and the ratio of these being greater than unity

Deep groove ball bearings are used for (a) heavy thrust load only (b) the small angular displacement of shafts (c) radial load at high speed (d) combined thrust and radial loads at high speed

Description : Deep groove ball bearings are used for (a) heavy thrust load only (b) the small angular displacement of shafts (c) radial load at high speed (d) combined thrust and radial loads at high speed

Last Answer : (d) combined thrust and radial loads at high speed

The tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads (d) none of the mentioned

Description : The tapered roller bearings can take (a) radial load only (b) axial load only (c) both radial and axial loads (d) none of the mentioned

Last Answer : (c) both radial and axial loads

Why CT operated over load relay is using for loads of high acceleration time upto 30 seconds? How it getting back?

Description : Why CT operated over load relay is using for loads of high acceleration time upto 30 seconds? How it getting back?

Last Answer : The saturable current transformers linearly transforms the current upto twice the set current, but above this value the transformer core gets saturated and the secondary current is proportionally less. Thus ... overload. When current reduces the core gets de-saturated, as material design is such. 

Ab and Ac are the cross sections of bronze and copper bars of equal lengt b c are their respective stresses due to load P. If Pb and Pc are the loads shared by them, (where Eb and Ec are their modulii). (A) b c = Eb /Ec (B) P = Pb + Pc (C) P = Ab b + Ac b (D) All the above

Description : Ab and Ac  are the cross sections of bronze and copper bars of equal lengt b c  are their  respective stresses due to load P. If Pb and Pc  are the loads shared by them, (where Eb and Ec  are  their modulii) ... /Ec (B) P = Pb + Pc (C) P = Ab b + Ac b (D) All the above 

Last Answer : (D) All the above 

When a series of wheel loads crosses a simply supported girder, the maximum bending moment under any given wheel load occurs when (A) The centre of gravity of the load system is midway between the centre of span and wheel load under consideration (B) The centre of span is midway between the centre of gravity of the load system and the wheel load under consideration (C) The wheel load under consideration is midway between the centre of span and the centre of gravity of the load system (D) None of the above

Description : When a series of wheel loads crosses a simply supported girder, the maximum bending moment under any given wheel load occurs when (A) The centre of gravity of the load system is midway between the centre of ... the centre of span and the centre of gravity of the load system (D) None of the above

Last Answer : (B) The centre of span is midway between the centre of gravity of the load system and the wheel load under consideration

The maximum bending moment due to a train of wheel loads on a simply supported girder (A) Always occurs at centre of span (B) Always occurs under a wheel load (C) Never occurs under a wheel load (D) None of the above

Description : The maximum bending moment due to a train of wheel loads on a simply supported girder (A) Always occurs at centre of span (B) Always occurs under a wheel load (C) Never occurs under a wheel load (D) None of the above

Last Answer : (B) Always occurs under a wheel load

Struts are load carrying members of a frame structure which are subjected to (A) Axial tension loads (B) Axial compressive loads (C) Torsional loads (D) Transverse loads

Description : Struts are load carrying members of a frame structure which are subjected to  (A) Axial tension loads  (B) Axial compressive loads  (C) Torsional loads  (D) Transverse loads 

Last Answer : (B) Axial compressive loads 

Ties are load carrying members of a frame, which are subjected to (A) Transverse loads (B) Axial tension loads (C) Axial compressive loads (D) Torsional loads

Description : Ties are load carrying members of a frame, which are subjected to  (A) Transverse loads  (B) Axial tension loads  (C) Axial compressive loads  (D) Torsional loads 

Last Answer : (B) Axial tension loads 

If l1 and l2 are the lengths of long and short spans of a two way slab simply supported on four edges and carrying a load w per unit area, the ratio of the loads split into w1 and w2acting on strips parallel to l2 and l1 is (A) w1/w2 = l2/l1 (B) w1/w2 = (l2/l1)² (C) w1/w2 = (l2/l1)3 (D) w1/w2 = (l2/l1)

Description : If l1 and l2 are the lengths of long and short spans of a two way slab simply supported on four edges and carrying a load w per unit area, the ratio of the loads split into w1 and w2acting on strips parallel to l2 and l1 is (A) ... l1 (B) w1/w2 = (l2/l1)² (C) w1/w2 = (l2/l1)3 (D) w1/w2 = (l2/l1)

Last Answer : Answer: Option D

If the length of a combined footing for two columns l metres apart is L and the projection on the left side of the exterior column is x, then the projection y on the right side of the exterior column, in order to have a uniformly distributed load, is (where is the distance of centre of gravity of column loads). (A) y = L - (l - ) (B) y = L/2 + (l - ) (C) y = L/2 - (l + ) (D) y = L/2 - (l - )

Description : If the length of a combined footing for two columns l metres apart is L and the projection on the left side of the exterior column is x, then the projection y on the right side of the exterior column, in order to have a uniformly distributed ... l - ) (C) y = L/2 - (l + ) (D) y = L/2 - (l - )

Last Answer : Answer: Option D

The rated loads of lifting cranes, as percentage of tipping load at specified radius, for crawlermounted and pneumatic tyre-mounted machines would be respectively (A) 80 and 90 (B) 90 and 80 (C) 85 and 75 (D) 75 and 83

Description : The rated loads of lifting cranes, as percentage of tipping load at specified radius, for crawlermounted and pneumatic tyre-mounted machines would be respectively (A) 80 and 90 (B) 90 and 80 (C) 85 and 75 (D) 75 and 83

Last Answer : (D) 75 and 83

Pick up the correct statement from the following: (A) The roof slabs of multi-storeyed buildings are constructed monolithically to carry the various floor loads (B) The beams of multi-storeyed buildings rest on girders and are the main load transferring members to the columns (C) The slab is spanned across the secondary beams provided between the main beams (D) All of these

Description : Pick up the correct statement from the following: (A) The roof slabs of multi-storeyed buildings are constructed monolithically to carry the various floor loads (B) The beams of multi-storeyed ... slab is spanned across the secondary beams provided between the main beams (D) All of these

Last Answer : Answer: Option D

For an I beam, the shape factor is 1.12. If the allowable stress (with factor of safety in bending as 1.5) is increased by 20% for wind and earthquake loads, the modified load factor is (a) 1.10 (b) 1.25 (c) 1.35 (d) 1.40

Description : For an I beam, the shape factor is 1.12. If the allowable stress (with factor of safety in bending as 1.5) is increased by 20% for wind and earthquake loads, the modified load factor is (a) 1.10 (b) 1.25 (c) 1.35 (d) 1.40

Last Answer : (d) 1.40

The most critical consideration in the design of a rolled steel column carrying axial loads is the (a) Percentage elongation at yield and the net cross-sectional area (b) Critical bending strength and axial yield strength of material (c) Buckling strength based on the net area of the section and percentage elongation at ultimate load (d) Compressive strength based on slenderness ratio and gross cross-sectional area.

Description : The most critical consideration in the design of a rolled steel column carrying axial loads is the (a) Percentage elongation at yield and the net cross-sectional area (b) Critical bending ... at ultimate load (d) Compressive strength based on slenderness ratio and gross cross-sectional area.

Last Answer : (d) Compressive strength based on slenderness ratio and gross cross-sectional area.

It is essential that the all possible yield line patterns have to be investigated to find the ------- ----- [ A ] Highest value of the ultimate load [ B ] Lowest value of the ultimate load [ C ] Average value of all the loads. [ D ] None of the above.

Description : It is essential that the all possible yield line patterns have to be investigated to find the ------------ [ A ] Highest value of the ultimate load [ B ] Lowest value of the ultimate load [ C ] Average value of all the loads. [ D ] None of the above.

Last Answer : [ B ] Lowest value of the ultimate load