Which of the following parameters are not required for evaluating volumetric efficiency of the compressor? a) Power b) Cylinder bore diameter c) Stroke length d) FAD

Which of the following parameters are not required for evaluating volumetric efficiency of the compressor? a) Power b) Cylinder bore diameter c) Stroke length d) FAD
by

1 Answer

Answer :

a) Power
by

Related questions

The ratio of isothermal power to actual measured input power of a compressor is known as: a) Isothermal efficiency b) Volumetric Efficiency c) Barometric efficiency d) None

Description : The ratio of isothermal power to actual measured input power of a compressor is known as: a) Isothermal efficiency b) Volumetric Efficiency c) Barometric efficiency d) None 

Last Answer : a) Isothermal efficiency

The volumetric efficiency of the compressor ______ with the increase in altitude of place a) increases b) decreases c) does not change d) None

Description : The volumetric efficiency of the compressor ______ with the increase in altitude of place a) increases b) decreases c) does not change d) None

Last Answer : b) decreases

The basic function of air dryer in a compressor is: a. prevent dust from entering compressor b. storage and smoothening pulsating air output c. reduce the temperature of the air before it enters the next state to increase efficiency d. to remove remaining traces of moisture after after-cooler

Description : The basic function of air dryer in a compressor is: a. prevent dust from entering compressor b. storage and smoothening pulsating air output c. reduce the temperature of the air before it enters the next state to increase efficiency d. to remove remaining traces of moisture after after-cooler 

Last Answer : d. to remove remaining traces of moisture after after-cooler 

If the performance of diesel engine of different sizes, cylinder dimensions and power rating are to be compared, which of the following parameters can be used for such comparison? (a) Swept volume (b) Air fuel ratio (c) Specific brake fuel consumption (d) Volumetric efficiency

Description : If the performance of diesel engine of different sizes, cylinder dimensions and power rating are to be compared, which of the following parameters can be used for such comparison? (a) Swept volume (b) Air fuel ratio (c) Specific brake fuel consumption (d) Volumetric efficiency

Last Answer : Ans :c

Reduction in the delivery pressure of a Compressor working at 7 bar, by 1 bar would reduce the power consumption by a) 6 to 10 % b) 2 to 3 % c) 12 to 14 % d) None of the above

Description : Reduction in the delivery pressure of a Compressor working at 7 bar, by 1 bar would reduce the power consumption by a) 6 to 10 % b) 2 to 3 % c) 12 to 14 % d) None of the above

Last Answer : a) 6 to 10 %

The percentage increase in power consumption of a compressor with suction side air filter and with the pressure drop across the filter of 200 mmWc is ____ a) 1.0% b) 3% c) 2.4% d) 1.6%

Description : The percentage increase in power consumption of a compressor with suction side air filter and with the pressure drop across the filter of 200 mmWc is ____ a) 1.0% b) 3% c) 2.4% d) 1.6% 

Last Answer : d) 1.6%

For every 4°C raise in air inlet temperature of an air compressor, the power consumption will increases by_____ a) 2% b) 1% c) 3% d) 4%

Description : For every 4°C raise in air inlet temperature of an air compressor, the power consumption will increases by_____ a) 2% b) 1% c) 3% d) 4%

Last Answer : b) 1%

The specific power consumption of non lubricated compressor compared to lubricated type is ____ a) Lesser b) Same c) Higher d) None

Description : The specific power consumption of non lubricated compressor compared to lubricated type is ____ a) Lesser b) Same c) Higher d) None 

Last Answer : c) Higher

Explain about the air compressor modulation by optimal pressure settings.

Description : Explain about the air compressor modulation by optimal pressure settings. 

Last Answer : Very often in an industry, different types, capacities and makes of compressors are connected to a common distribution network. In such situations, proper selection of a right combination of compressors and ... different pressures and energy efficient ones must be made to meet most of the demand. 

Can you explain how temperature of inlet air affects the energy consumption of an air compressor?

Description : Can you explain how temperature of inlet air affects the energy consumption of an air compressor?

Last Answer : As a thumb rule “for every 4 °C rise in inlet air temperature results in a higher energy consumption by 1% to achieve equivalent output”. Hence cool air intake leads to a more efficient compression.

What are the different types of pressure regulators available for air compressor system?

Description : What are the different types of pressure regulators available for air compressor system? 

Last Answer : Pilot operated type Direct acting type Self – relieving type 

What are the limitations of a centrifugal compressor operation?

Description : What are the limitations of a centrifugal compressor operation? 

Last Answer : The major limitation of a centrifugal compressor is that is operates at peak efficiency at design point only and any deviation from the operating point is detrimental to its performance. When selecting ... at high pressure, with the consequent reduction in flow, the surge point is not reached.

Briefly describe about ‘rotary compressor’?

Description : Briefly describe about ‘rotary compressor’?  

Last Answer : Rotary compressors have rotors in place of pistons and give a continuous, pulsation free discharge. They operate at high speed and generally provide higher throughput than reciprocating compressors. They are directly ... , vibrate less, and have a lower number of parts which are subject to wear. 

If the compressor of 200 cfm loads in 10 seconds and unloads in 20 seconds, the air leakage would be_____ a) 67 cfm b) 100 cfm c) 10 cfm d) 133 cfm

Description : If the compressor of 200 cfm loads in 10 seconds and unloads in 20 seconds, the air leakage would be_____ a) 67 cfm b) 100 cfm c) 10 cfm d) 133 cfm 

Last Answer : a) 67 cfm

From base load operation and from achieving best specific energy consumption point of view, which of the following compressors are suitable? a) Single stage reciprocating compressors b) Centrifugal compressors c) Two stage reciprocating compressor d) Multi stage reciprocating compressor

Description : From base load operation and from achieving best specific energy consumption point of view, which of the following compressors are suitable? a) Single stage reciprocating compressors b) Centrifugal compressors c) Two stage reciprocating compressor d) Multi stage reciprocating compressor

Last Answer : b) Centrifugal compressors

From the point of lower specific energy consumption, which of the following compressors are suitable for part load operation? a) Two stage reciprocating compressors b) Centrifugal compressors c) Two stage screw compressor d) Single stage screw compressor

Description : From the point of lower specific energy consumption, which of the following compressors are suitable for part load operation? a) Two stage reciprocating compressors b) Centrifugal compressors c) Two stage screw compressor d) Single stage screw compressor

Last Answer : a) Two stage reciprocating compressors

Which of the statement is “True” for centrifugal compressors? a) The compressor should not be operated at full load b) The compressor should be operated at shut off pressure c) The compressor should not be operated with inlet-guide vane control d) The compressor should not be operated close to the surge point

Description : Which of the statement is True for centrifugal compressors? a) The compressor should not be operated at full load b) The compressor should be operated at shut off pressure c) The ... operated with inlet-guide vane control d) The compressor should not be operated close to the surge point 

Last Answer : d) The compressor should not be operated close to the surge point

The discharge temperature of two stage compressor compared to single stage one is ____ a) Lesser b) Same c) Higher d) None

Description : The discharge temperature of two stage compressor compared to single stage one is ____ a) Lesser b) Same c) Higher d) None  

Last Answer : a) Lesser

The compressor capacity of a reciprocating compressor is directly proportional to __ a) Speed b) Pressure c) Volume d) All

Description : The compressor capacity of a reciprocating compressor is directly proportional to __ a) Speed b) Pressure c) Volume d) All 

Last Answer : a) Speed

Which of the following type does Screw compressor belongs to? a) Positive displacementcompressor b) Dynamic compressors c) Both a & b d) None of the above

Description : Which of the following type does Screw compressor belongs to? a) Positive displacementcompressor b) Dynamic compressors c) Both a & b d) None of the above 

Last Answer : a) Positive displacementcompressor

The ratio of indicated power to shaft power of the engine required to drive the compressor is called A. Compressor efficiency B. Volumetric efficiency C. Isothermal efficiency D. Mechanical efficiency

Description : The ratio of indicated power to shaft power of the engine required to drive the compressor is called A. Compressor efficiency B. Volumetric efficiency C. Isothermal efficiency D. Mechanical efficiency

Last Answer : ANSWER : D

Why inter-coolers are required for multi-stage reciprocating compressors?

Description : Why inter-coolers are required for multi-stage reciprocating compressors?  

Last Answer : The intercoolers reduce the temperature of air/gas discharged between stages. Ideally, the intake temperature at each stage should be the same as that at the first stage (referred to a perfect cooling), so that the volume of air to be compressed does not increase and hence reduced power consumption.

The likely estimate on equivalent power wastage for a leakage from 7 bar compressed air system through 1.6 mm orifice size is ____ a) 0.2 kW b) 3.0 kW c) 0.8 kW d) 12 kW

Description : The likely estimate on equivalent power wastage for a leakage from 7 bar compressed air system through 1.6 mm orifice size is ____ a) 0.2 kW b) 3.0 kW c) 0.8 kW d) 12 kW

Last Answer : c) 0.8 kW

A gas engine has a volume of 300 cc and clearance volume of 25 cc. Its volumetric efficiency is 0.8 and mech efficiency is 0.9. What is the volume of the mixture taken in per stroke? (a) 248 cc (b) 252 cc (c) 264 cc (d) 286 cc

Description : A gas engine has a volume of 300 cc and clearance volume of 25 cc. Its volumetric efficiency is 0.8 and mech efficiency is 0.9. What is the volume of the mixture taken in per stroke? (a) 248 cc (b) 252 cc (c) 264 cc (d) 286 cc

Last Answer : Ans : c

Volumetric efficiency is affected by (A) Turbulence velocity and temperature of intake manifold (B) Efficiency of exhaust stroke (C) Valve timing overlap (D) All the above

Description : Volumetric efficiency is affected by (A) Turbulence velocity and temperature of intake manifold (B) Efficiency of exhaust stroke (C) Valve timing overlap (D) All the above

Last Answer : (D) All the above

In four stroke engine which of the following is also known as power stroke a. Suction stroke b. Compression stroke c. Expansion stroke d. Exhaust stroke (Ans:c) Measurements of fuel and air consumption, brake power and incylinder pressure. Tutorials on engine performance parameters. Heat balance sheet. Engine performance curves. 1. The increase in intake air temperature into IC engine,___________its efficiency A. increase B. decrease C. does not alter D. unpredictable on

Description : In four stroke engine which of the following is also known as power stroke a. Suction stroke b. Compression stroke c. Expansion stroke d. Exhaust stroke (Ans:c) Measurements of fuel and air ... into IC engine,___________its efficiency A. increase B. decrease C. does not alter D. unpredictable on

Last Answer : ANSWER : B

A reciprocating compressor is not suitable for use as a supercharger because: A. it runs at lower rpm B. the pressure ratio is high C. volumetric efficiency is high D. it is bulky and can handle small quantity of air

Description : A reciprocating compressor is not suitable for use as a supercharger because: A. it runs at lower rpm B. the pressure ratio is high C. volumetric efficiency is high D. it is bulky and can handle small quantity of air

Last Answer : ANSWER : D

The clearance volume of the air compressor is kept minimum because A. It allows maximum compression to be achieved B. It greatly affects volumetric efficiency C. It results in minimum work D. It permits isothermal compression

Description : The clearance volume of the air compressor is kept minimum because A. It allows maximum compression to be achieved B. It greatly affects volumetric efficiency C. It results in minimum work D. It permits isothermal compression

Last Answer : ANSWER : B

Volumetric efficiency of air compressor is of the order of A. 20% to 30 % B. 40% to 50% C. 60% to 70% D. 70% to 90%

Description : Volumetric efficiency of air compressor is of the order of A. 20% to 30 % B. 40% to 50% C. 60% to 70% D. 70% to 90%

Last Answer : ANSWER : D

Volumetric efficiency of a compressor without clearance volume A. Increases with increase in compression ratio B. Decreases wit increase in compression ratio C. Not dependent upon compression ratio D. Unpredictable

Description : Volumetric efficiency of a compressor without clearance volume A. Increases with increase in compression ratio B. Decreases wit increase in compression ratio C. Not dependent upon compression ratio D. Unpredictable

Last Answer : ANSWER : C

Which one of the following statement is not correct for the volumetric efficiency of a reciprocating air compressor? A. It decreases with increase in ambient temperature B. It increases with decrease in pressure ratio C. It increases with decrease in clearance ratio D. It decreases with increases in delivery pressure

Description : Which one of the following statement is not correct for the volumetric efficiency of a reciprocating air compressor? A. It decreases with increase in ambient temperature B. It increases with ... It increases with decrease in clearance ratio D. It decreases with increases in delivery pressure

Last Answer : ANSWER : A

Which one of the following statements are correct for reciprocating air compressor? A. Its volumetric efficiency increases with increasing clearance ratio B. Its volumetric efficiency increases with pressure ratio C. Its volumetric efficiency does not vary with change in clearance ratio and pressure ratio D. Its volumetric efficiency decreases with increasing clearance ratio and pressure ratio

Description : Which one of the following statements are correct for reciprocating air compressor? A. Its volumetric efficiency increases with increasing clearance ratio B. Its volumetric efficiency increases ... ratio D. Its volumetric efficiency decreases with increasing clearance ratio and pressure ratio

Last Answer : ANSWER : D

How the net work to drive a compressor and its volumetric efficiency behave with increase in clearance volume ?

Description : How the net work to drive a compressor and its volumetric efficiency behave with increase in clearance volume ?

Last Answer : Work remains unaltered and volumetric efficiency decreases.

With increase in compression ratio, the volumetric efficiency of air compressor (A) Increases (B) Decreases (C) Remain same (D) May increase or decrease (depends on the suction pressure)

Description : With increase in compression ratio, the volumetric efficiency of air compressor (A) Increases (B) Decreases (C) Remain same (D) May increase or decrease (depends on the suction pressure)

Last Answer : Option A

State the various factors affecting volumetric efficiency of air compressor

Description : State the various factors affecting volumetric efficiency of air compressor 

Last Answer : Factors affecting volumetric efficiency of reciprocating air compressor: 1) Clearance Volume 2) Restricted passage and leakage at inlet valves 3) Speed of rotation 4) Piston ring leakages ... wall, it get expanded, which decreases the charge taken in therefore volumetric efficiency decreases. 

Define (i) I.P (ii) B.P (iii)Volumetric efficiency (iv)Isothermal efficiency of air compressor

Description : Define (i) I.P (ii) B.P (iii)Volumetric efficiency (iv)Isothermal efficiency of air compressor

Last Answer : i) I.P. - It is the ratio of polytrophic work into speed of compressor in revolution per second.   ii) B.P. - It is the power required to drive the compressor or power delivered to ... the ratio of isothermal power to the shaft power or brake power of motor required to drive the compressor  

Explain the factors affecting volumetric efficiency of reciprocating air compressor.

Description : Explain the factors affecting volumetric efficiency of reciprocating air compressor.

Last Answer : Factors affecting volumetric efficiency of reciprocating air compressor: 1) Clearance Volume 2) Restricted passage and leakage at inlet valves 3) Speed of rotation 4) Piston ring leakages ... wall, it get expanded, which decreases the charge taken in therefore volumetric efficiency decreases.

An engine working on air standard Otto cycle has a cylinder diameter of 10 cm and stroke length of 15 cm. The ratio of specific heats for air is 1.4. If the clearance volume is 196.3 cc and the heat supplied per kg of air per cycle is 1800 kJ/kg, then work output per cycle per kg of air is a. 879.1 kJ/ b. 890.2 kJ c. 895.3 kJ d. 973.5 kJ

Description : An engine working on air standard Otto cycle has a cylinder diameter of 10 cm and stroke length of 15 cm. The ratio of specific heats for air is 1.4. If the clearance volume is 196.3 cc and the heat supplied per kg of air per ... kg of air is a. 879.1 kJ/ b. 890.2 kJ c. 895.3 kJ d. 973.5 kJ

Last Answer : ANSWER d. 973.5 kJ

The variable required to be known in correlations used for estimating the horse power of a centrifugal gas compressor and hence its cost is P. Inlet pressure Q. Compressor rpm R. Delivery pressure S. Volumetric flow rate at inlet. (A) P, Q and R (B) P and R (C) R and S (D) P, Rand S

Description : The variable required to be known in correlations used for estimating the horse power of a centrifugal gas compressor and hence its cost is P. Inlet pressure Q. Compressor rpm R. Delivery pressure S. Volumetric flow rate at inlet. (A) P, Q and R (B) P and R (C) R and S (D) P, Rand S

Last Answer : (A) P, Q and R

Air Conditioning/ Electrical

Description : The coil of a transformer that is energized from a source of alternating voltage is known as the: A. low voltage winding B. high voltage winding C. primary winding D. secondary winding

Last Answer : C

Electricity or Air Conditioning

Description : There is a single-phase motor connected in parallel with an electric heater unit. If the heater is switched off, then the overall power factor angle of the circuit will: A. increase B. decrease C. stay the same D. none of the above

Last Answer : A

Explain the simple steps that can be followed in shop – floor for quantification of compressed air leakages.

Description : Explain the simple steps that can be followed in shop – floor for quantification of compressed air leakages.  

Last Answer : The following steps can be followed for quantification of compressed air leakages. Shut off compressed air operated equipments (or conduct test when no equipment is using compressed air). Run the compressor to ... per minute (cmm) T = Time on load in minutes T = Time unload in minutes 

What are the methods of capacity control in centrifugal air compressors?

Description : What are the methods of capacity control in centrifugal air compressors?  

Last Answer : Centrifugal compressors operate best at the design point. They are prone to surging at flow rates less than 50% of the rated capacity. The following types of controls are employed in ... variable speed drives to match compressor output to meet varying load requirements is by speed control 

What is the effect of increase in altitude on the performance of single stage reciprocating compressors?

Description : What is the effect of increase in altitude on the performance of single stage reciprocating compressors? 

Last Answer : With the increase in altitude, there will be reduction in air pressure, which results in increase in compression ratio, leading to higher discharge temperature and reduced efficiency. 

What are the most common types of compressed air dryers used?

Description : What are the most common types of compressed air dryers used? 

Last Answer : a. Heat – less dryer (absorption) b. Adsorption dryer c. Chiller dryer (refrigerated dryers)

List the advantages of keeping the discharge pressure for reciprocating compressors at minimum.

Description : List the advantages of keeping the discharge pressure for reciprocating compressors at minimum. 

Last Answer : Lower power consumption Less load on the piston rods and hence reduced maintenance costs Lower leakage losses

List the means of capacity control for reciprocating compressors.

Description : List the means of capacity control for reciprocating compressors. 

Last Answer : On/off control Load and unload control Multi-step control

What are the likely effects of using very cold water in intercoolers for reciprocating compressors?

Description : What are the likely effects of using very cold water in intercoolers for reciprocating compressors? 

Last Answer : Use of very cold water can result in condensation which may result in water entering the cylinder, thereby reducing valve life, accelerating wear and scoring of piston, piston rings and ... and cause rust which will result in abrasion during compressor operation and significantly reduce efficiency. 

List the components of a compressed air system.

Description : List the components of a compressed air system. 

Last Answer : The various components of a compressed air system are: • Intake air filters • Inter-stage coolers • After coolers • Air-dryers • Moisture traps • Receivers 

Explain about the importance of optimal Pressure settings of a compressed air network

Description : Explain about the importance of optimal Pressure settings of a compressed air network 

Last Answer : The power consumed by a compressor depends on its operating pressure and rated capacity. They should not be operated above their optimum operating pressure as this not only wastes energy, but also leads ... switches must be adjusted such that the compressor cut-in and cuts-off at optimum levels.