Velocity error constant of a system is measured when the input to the ...

Velocity error constant of a system is measured when the input to the system is unit _______ function.
by
edited

1 Answer

Answer :

Velocity error constant of a system is measured when the input to the system is unit ramp function.
by
edited

Related questions

What is the steady state error of type-0 system for ramp input?

Description : What is the steady state error of type-0 system for ramp input?  A) ∞ B) A/K C) A/(1+K) D) 0

Last Answer : What is the steady state error of type-0 system for ramp input?  A) ∞ B) A/K C) A/(1+K) D) 0

For a feedback control system of type 2, the steady error for a rap input is

Description : For a feedback control system of type 2, the steady error for a rap input is  A) Infinite B) Constant C) Zero D) Indeterminate

Last Answer : For a feedback control system of type 2, the steady error for a rap input is Zero 

If stability error for step input and speed of response be the criteria for design, what controller would you

Description : If stability error for step input and speed of response be the criteria for design, what controller would you recommend (1) P controller (2) PD controller (3) PI controller (4) PID controller

Last Answer : If stability error for step input and speed of response be the criteria for design, what controller would you recommend (1) P controller (2) PD controller (3) PI controller (4) PID controller

How can the steady-state error in a system be reduced?

Description : How can the steady-state error in a system be reduced?  (1) By decreasing the type of system (2) By increasing system gain (3) By decreasing the static error constant (4) By increasing the input

Last Answer : How can the steady-state error in a system be reduced?  (1) By decreasing the type of system (2) By increasing system gain (3) By decreasing the static error constant (4) By increasing the input

In order to regulate steady state error to zero, in a negative feedback control system, one employs

Description : In order to regulate steady state error to zero, in a negative feedback control system, one employs

Last Answer : In order to regulate steady state error to zero, in a negative feedback control system, one employs Integral control

The steady state error of the system can be minimized by

Description : The steady state error of the system can be minimized by

Last Answer : The steady state error of the system can be minimized by increasing gain k

In a control system integral error compensation _______ steady state error.

Description : In a control system integral error compensation _______ steady state error.

Last Answer : In a control system integral error compensation minimizes steady state error.

Consider a continuous-time system with input x(t) & output y(t) are related by y(t) = x (sin t). This system is

Description : Consider a continuous-time system with input x(t) & output y(t) are related by y(t) = x (sin t). This system is (A) causal & linear (B) non-causal & linear (C) causal & non-linear (D) non-causal & non-linear

Last Answer : Consider a continuous-time system with input x(t) & output y(t) are related by y(t) = x (sin t). This system is non-causal & linear

If a step function is applied to the input of a system and the output...

Description : If a step function is applied to the input of a system and the output remains below a certain level for all the time, the system is?

Last Answer : If a step function is applied to the input of a system and the output remains below a certain level for all the time, the system is not necessarily stable.

In lag compensator the damping ratio, gain and steady state error (ess) are

Description : In lag compensator the damping ratio, gain and steady state error (ess) are   (a) Decreases, Decreases and Increases (b) Decreases, Increases and Increases (c) Increases, Increases and Decreases (d) Increases, Decreases and Decreases

Last Answer : In lag compensator the damping ratio, gain and steady state error (ess) are Increases, Decreases and Decreases

The effect of error damping is to?

Description : The effect of error damping is to?

Last Answer : The effect of error damping is to reduce steady state error.

Static error co-efficients are used as a measure of the effectiveness of...

Description : Static error co-efficients are used as a measure of the effectiveness of closed loop systems for specified ________ input signal.

Last Answer : acceleration , velocity, position 

The rate of an enzyme catalyzed reaction was measured using several substrate concentrations that were much lower than Km, the dependence of reaction velocity on substrate concentration can best be described as (A) Independent of enzyme concentration (B) A constant fraction of Vmax (C) Equal to Km (D) Proportional to the substrate concentration

Description : The rate of an enzyme catalyzed reaction was measured using several substrate concentrations that were much lower than Km, the dependence of reaction velocity on substrate concentration can best be ... constant fraction of Vmax (C) Equal to Km (D) Proportional to the substrate concentration

Last Answer : Answer : C

The position and velocity errors of a type-2 system are?

Description : The position and velocity errors of a type-2 system are?

Last Answer : The position and velocity errors of a type-2 system are zero, constant.

Draw the block diagram of discrete input module & explain each block.

Description : Draw the block diagram of discrete input module & explain each block.

Last Answer : Power conversion: It consists of rectifier which converts the incoming AC signal to a pulsating dc level, which is passed through filter and other logic in order to deliver a clean and denounced dc ... Logic section: It passes the input signal to the module s input address LED and the CPU.

List any four input and four output devices used with PLC.

Description : List any four input and four output devices used with PLC.

Last Answer : Input device: 1. Push button. 2. Temperature switches. 3. Limit switches. 4. Pressure switches. 5. Level Switches. 6. Proximity Switches. Output devices: 1. Motor. 2. Display. 3. Heater coil. 4. Relay. 5. Lamp. 6. Buzzer.

_________is the reference input minus the primary feedback.

Description : _________is the reference input minus the primary feedback.

Last Answer : Actuating signal is the reference input minus the primary feedback.

A signal other than the reference input that tends to affect the value of controlled variable is known as ?

Description : A signal other than the reference input that tends to affect the value of controlled variable is known as ?

Last Answer : A signal other than the reference input that tends to affect the value of controlled variable is known as disturbance.

The initial response when the output is not equal to input is called?

Description : The initial response when the output is not equal to input is called?

Last Answer : The initial response when the output is not equal to input is called Transient response.

In force-voltage analogy, velocity is analogous to?

Description : In force-voltage analogy, velocity is analogous to?

Last Answer : In force-voltage analogy, velocity is analogous to current.

A transfer function has a second order denominator and constant gain in the numerator

Description : A transfer function has a second order denominator and constant gain in the numerator

Last Answer : A transfer function has a second order denominator and constant gain in the numerator the system has two zeros at infinity

The time constant of the servo-mechanism can be decreased by

Description : The time constant of the servo-mechanism can be decreased by

Last Answer : The time constant of the servo-mechanism can be decreased by decreasing the inertia of the system

Spring constant in force-voltage analogy is analogous to?

Description : Spring constant in force-voltage analogy is analogous to?

Last Answer : Spring constant in force-voltage analogy is analogous to reciprocal of capacitance.

Which one of the following is not a definition of error ? (A) It refers to the discrepancy between a computed, observed or measured value and the true, specified or theoretically correct value. (B) It refers to the actual output of a software and the correct output. (C) It refers to a condition that causes a system to fail. (D) It refers to human action that results in software containing a defect or fault.

Description : Which one of the following is not a definition of error ? (A) It refers to the discrepancy between a computed, observed or measured value and the true, specified or theoretically correct value. (B) It ... to fail. (D) It refers to human action that results in software containing a defect or fault. 

Last Answer : The input, or clock pulse.

Which terminology deals with the excitation or stimulus applied to the system from an external source for the generation of an output? a. Input signal b. Output signal c. Error signal d. Feedback signal

Description : Which terminology deals with the excitation or stimulus applied to the system from an external source for the generation of an output? a. Input signal b. Output signal c. Error signal d. Feedback signal

Last Answer : Ans: A

The transfer function of a system is 10/(1+s) when operating as a unity feedback system, the steady state error to a step input will be a) 0 b) 1/11 c) 10 d) Infinity

Description : The transfer function of a system is 10/(1+s) when operating as a unity feedback system, the steady state error to a step input will be a) 0 b) 1/11 c) 10 d) Infinity

Last Answer : Ans: 1/11

Which technique can be used to achieve input and output coverage? It can be applied to human input, input via interfaces to a system, or interface parameters in integration testing. A. Error Guessing B. Boundary Value Analysis C. Decision Table testing D. Equivalence partitioning

Description : Which technique can be used to achieve input and output coverage? It can be applied to human input, input via interfaces to a system, or interface parameters in integration testing. A. Error Guessing B. Boundary Value Analysis C. Decision Table testing D. Equivalence partitioning

Last Answer : D. Equivalence partitioning

Which technique can be used to achieve input and output coverage? It can be applied to human input, input via interfaces to a system, or interface parameters in integration testing. a) Error Guessing b) Boundary Value Analysis c) Decision Table testing d) Equivalence partitioning

Description : Which technique can be used to achieve input and output coverage? It can be applied to human input, input via interfaces to a system, or interface parameters in integration testing. a) Error Guessing b) Boundary Value Analysis c) Decision Table testing d) Equivalence partitioning

Last Answer : d) Equivalence partitioning

A uniform slope was measured by the method of stepping. If the difference in level between two points is 1.8 m and the slope distance between them is 15 m, the error is approximately equal to (A) Cumulative, + 0.11 m (B) Compensating, ± 0.11 m (C) Cumulative, - 0.11 m (D) None of these

Description : A uniform slope was measured by the method of stepping. If the difference in level between two points is 1.8 m and the slope distance between them is 15 m, the error is approximately equal to (A) Cumulative, + 0.11 m (B) Compensating, ± 0.11 m (C) Cumulative, - 0.11 m (D) None of these

Last Answer : (A) Cumulative, + 0.11 m

Offsets are measured with an accuracy of 1 in 40. If the point on the paper from both sources of error (due to angular and measurement errors) is not to exceed 0.05 cm on a scale of 1 cm = 20 m, the maximum length of offset should be limited to (A) 14.14 m (B) 28.28 m (C) 200 m (D) None of these

Description : Offsets are measured with an accuracy of 1 in 40. If the point on the paper from both sources of error (due to angular and measurement errors) is not to exceed 0.05 cm on a scale of 1 cm = 20 m, the maximum length of ... should be limited to (A) 14.14 m (B) 28.28 m (C) 200 m (D) None of these

Last Answer : (B) 28.28 m

True value has been 50 whereas measured value is 40 then the percentage error in the reading

Description : True value has been 50 whereas measured value is 40 then the percentage error in the reading will be ______.  (A) 20% (B) 40% (C) 50% (D) 30%

Last Answer : True value has been 50 whereas measured value is 40 then the percentage error in the reading will be 20%. 

What is the purpose of either 'setpoint module' (6000F090/030) shown in the illustration? EL-0094 A. Program the 'signal conditioner' as to how to vary its input. B. Supply 0 - 10 volts to the 'signal conditioner'. C. Initiate logging of measured information at set intervals; for example, each hour. D. Obtain an input from the 'signal conditioner' and, if outside set limits, signals the 'annunciator'.

Description : What is the purpose of either 'setpoint module' (6000F090/030) shown in the illustration? EL-0094 A. Program the 'signal conditioner' as to how to vary its input. B. Supply 0 - 10 volts to ... . Obtain an input from the 'signal conditioner' and, if outside set limits, signals the 'annunciator'.

Last Answer : Answer: D

When troubleshooting most electronic circuits, 'loading effect' can be minimized by using a voltmeter with a/an ___________________. A. input impedance much greater than the impedance across which the voltage is being measured B. input impedance much less than the impedance across which the voltage is being measured C. sensitivity of less than 1000 ohms/volt D. sensitivity of more than 1000 volts/ohm

Description : When troubleshooting most electronic circuits, 'loading effect' can be minimized by using a voltmeter with a/an ___________________. A. input impedance much greater than the impedance across which the voltage ... sensitivity of less than 1000 ohms/volt D. sensitivity of more than 1000 volts/ohm

Last Answer : Answer: A

Characteristics impedance of a transmission line is the impedance measured at the ___________ when its length is infinite. A. input B. shorted end of the line C. output D. midsection

Description : Characteristics impedance of a transmission line is the impedance measured at the ___________ when its length is infinite. A. input B. shorted end of the line C. output D. midsection

Last Answer : A. input

Most AC voltmeters have an rms scale which is valid only if the input signal being measured is a __ signal.

Description : Most AC voltmeters have an rms scale which is valid only if the input signal being measured is a __ signal.

Last Answer : sinusoidal

EMD is best described by which statement? ∙ A. 70 percent of the core diameter and 70% of the fiber NA should be filled with light. ∙ B. 70 percent of the fiber diameter and 70% of the cone of acceptance should be filled with light. ∙ C. 70 percent of input light should be measured at the output. ∙ D. 70 percent of the unwanted wavelengths should be attenuated by the fiber.

Description : EMD is best described by which statement? ∙ A. 70 percent of the core diameter and 70% of the fiber NA should be filled with light. ∙ B. 70 percent of the fiber diameter and 70% of the ... be measured at the output. ∙ D. 70 percent of the unwanted wavelengths should be attenuated by the fiber.

Last Answer : 70 percent of the core diameter and 70% of the fiber NA should be filled with light.

EMDis best describe bywhich statement? a. 70percentofthe corediameter and70%ofthefiberNAshouldbe filled with light b.70 percent of the fiber diameter and 70% of the cone of acceptance should be filled with light c.70 percent of input light should be measured at the output d.70 percent of the unwanted wavelengths should be attenuated by the fiber

Description : EMDis best describe bywhich statement? a. 70percentofthe corediameter and70%ofthefiberNAshouldbe filled with light b.70 percent of the fiber diameter and 70% of the cone of acceptance should be filled with ... the output d.70 percent of the unwanted wavelengths should be attenuated by the fiber

Last Answer : a. 70percentofthe corediameter and70%ofthefiberNAshouldbe filled with light

Material price, mix, usage and revised quantity variances are measured on _______ basis, whereas material yield variance is measured on _______ basis. A. Output, Input B. Output, Output C. Input, Output D. None of the above

Description : Material price, mix, usage and revised quantity variances are measured on _______ basis, whereas material yield variance is measured on _______ basis. A. Output, Input B. Output, Output C. Input, Output D. None of the above

Last Answer : C. Input, Output

The ratio of isothermal power to actual measured input power of a compressor is known as: a) Isothermal efficiency b) Volumetric Efficiency c) Barometric efficiency d) None

Description : The ratio of isothermal power to actual measured input power of a compressor is known as: a) Isothermal efficiency b) Volumetric Efficiency c) Barometric efficiency d) None 

Last Answer : a) Isothermal efficiency

The voltage of a circuit is measured by a voltmeter having input...

Description : The voltage of a circuit is measured by a voltmeter having input impedance comparable with the output impedance of the circuit thereby causing error in voltage measurement. This error may be called as_________.

Last Answer : error caused by misuse of instrument

GHCi Error : parse error on input `=' in Haskell -Web-Development

Description : GHCi Error : parse error on input `=' in Haskell -Web-Development

Last Answer : answer:

The front panel display provides lights as green LED represent sand red LED represent _ for device programmer who writes input/output basic: a. Busy and Error b. Error and Busy c. Busy and Busy d. Error and Error

Description : The front panel display provides lights as green LED represent sand red LED represent _ for device programmer who writes input/output basic: a. Busy and Error b. Error and Busy c. Busy and Busy d. Error and Error

Last Answer : a. Busy and Error

In successive-approximation A/D converter, offset voltage equal to 1/2 LSB is added to the D/A converter’s output. This is done to (A) Improve the speed of operation. (B) Reduce the maximum quantization error. (C) Increase the number of bits at the output. (D) Increase the range of input voltage that can be converted

Description : In successive-approximation A/D converter, offset voltage equal to 1/2 LSB is added to the D/A converter's output. This is done to (A) Improve the speed of operation. (B) Reduce the maximum ... Increase the number of bits at the output. (D) Increase the range of input voltage that can be converted

Last Answer : (B) Reduce the maximum quantization error.

Feed is measured in units of a.length/revolution b.degree/revolution c.length d.velocity

Description : Feed is measured in units of a.length/revolution b.degree/revolution c.length d.velocity

Last Answer : a.length/revolution

The velocity of wind is measured by

Description : The velocity of wind is measured by

Last Answer : Anaemometer

Who measured the velocity of light first? (1) Galileo (2) Newton (3) Romer (4) Einstein

Description : Who measured the velocity of light first? (1) Galileo (2) Newton (3) Romer (4) Einstein

Last Answer : (3) Romer Explanation: Galileo is often credited with being the first scientist to try to determine the speed of light. Galileo's experiment was carried out by the Accademia del Cimento of Florence ... 11 microseconds. The first quantitative estimate of the speed alight was made in 1676 by Romer.

Velocity of liquid hydrocarbon fuels in a pipeline cannot be measured by magnetic flow-meters, because their __________ is very low/small. (A) Thermal conductivity (B) Electrical conductivity (C) Specific gravity

Description : Velocity of liquid hydrocarbon fuels in a pipeline cannot be measured by magnetic flow-meters, because their __________ is very low/small. (A) Thermal conductivity (B) Electrical conductivity (C) Specific gravity

Last Answer : (C) Specific gravity

Venturimeters, orificemeters and nozzles are used to measure the fluid discharge from a pipeline. The average fluid velocity in a pipeline can be measured by a/an (A) Weir (B) Hot wire anemometer (C) Cup and vane anemometer (D) None of these

Description : Venturimeters, orificemeters and nozzles are used to measure the fluid discharge from a pipeline. The average fluid velocity in a pipeline can be measured by a/an (A) Weir (B) Hot wire anemometer (C) Cup and vane anemometer (D) None of these

Last Answer : (B) Hot wire anemometer

For turbulent flow in smooth circular pipe, the velocity distribution is a function of the distance 'd' measured from the wall of the pipe and the friction velocity 'v', and it follows a __________ relationship. (A) Logarithmic (B) Linear (C) Hyperbolic (D) Parabolic

Description : For turbulent flow in smooth circular pipe, the velocity distribution is a function of the distance 'd' measured from the wall of the pipe and the friction velocity 'v', and it follows a __________ relationship. (A) Logarithmic (B) Linear (C) Hyperbolic (D) Parabolic

Last Answer : (A) Logarithmic