A cube of material of side 1 cm has a resistance of 0.002 ohm between...

A cube of material of side 1 cm has a resistance of 0.002 ohm between its opposite faces. If the same volume of the material has a length of 8 cm and a uniform cross-section, the resistance of this length will be 
by

1 Answer

Answer :

A cube of material of side 1 cm has a resistance of 0.002 ohm between its opposite faces. If the same volume of the material has a length of 8 cm and a uniform cross-section, the resistance of this length will be 0.128 ohm.

by

Related questions

Consider a cube of material of sides 1 cm with a resistance of 0.003 Ω between its opposite faces. What is the

Description : Consider a cube of material of sides 1 cm with a resistance of 0.003 Ω between its opposite faces. What is the resistance if the same volume of the material is drawn into a length of 50 cm with a uniform cross – section? A) 0.003 Ω B) 0.15 Ω C) 7.5 Ω D) None of these

Last Answer : Consider a cube of material of sides 1 cm with a resistance of 0.003 Ω between its opposite faces. What is the resistance if the same volume of the material is drawn into a length of 50 cm with a uniform cross – section? A) 0.003 Ω B) 0.15 Ω C) 7.5 Ω D) None of these

A wire of 0.14 mm diameter and specific resistance 9.6 micro ohm-cm is 440 cm long. The resistance of the wire will be

Last Answer : A wire of 0.14 mm diameter and specific resistance 9.6 micro-ohm-cm is 440 cm long. The resistance of the wire will be 27.4 ohm.

Twelve 1 ohm resistances are used as edge to form a cube. The resistance between two diagonally opposite ...

Description : Twelve 1 ohm resistances are used as edge to form a cube. The resistance between two diagonally opposite corners of the cube is:  (1) 5/6 ohm (2) 1 ohm (3) 6/5 ohm (4) 3/2 ohm

Last Answer : Twelve 1 ohm resistances are used as edge to form a cube. The resistance between two diagonally opposite corners of the cube is: 5/6 ohm.

If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 × 105 N/mm2 ) when subjected to a twisting moment, produces maximum shear stress of 50 N/mm2 , the angle of twist in radians, is (A) 0.001 (B) 0.002 (C) 0.0025 (D) 0.003

Description : If a solid shaft (diameter 20 cm, length 400 cm, N = 0.8 × 105  N/mm2 ) when subjected to a twisting  moment, produces maximum shear stress of 50 N/mm2 , the angle of twist in radians, is  (A) 0.001  (B) 0.002  (C) 0.0025  (D) 0.003 

Last Answer : (C) 0.0025 

When a constant discharge 2.91 litres/sec. was obtained in a pumping test, the draw downs in the test wells at 3 m and 6.184 m were 2.6 m and 0.3 m respectively. If over-all depth of the pumping well was 16 m, the permeability of the soil, is (A) 0.0005 cm/sec (B) 0.001 cm/sec (C) 0.002 cm/sec (D) 0.01 cm/sec

Description : When a constant discharge 2.91 litres/sec. was obtained in a pumping test, the draw downs in the test wells at 3 m and 6.184 m were 2.6 m and 0.3 m respectively. If over-all depth of the pumping well was 16 m, the ... (A) 0.0005 cm/sec (B) 0.001 cm/sec (C) 0.002 cm/sec (D) 0.01 cm/sec

Last Answer : Answer: Option B

A potentiometer having the potential gradient of `2 mV//cm` is used to measure the difference of potential across a resistance of `10 ohm`. If a lengt

Description : A potentiometer having the potential gradient of `2 mV//cm` is used to measure the difference of potential across a resistance of `10 ohm`. If a lengt

Last Answer : A potentiometer having the potential gradient of `2 mV//cm` is used to measure the difference of potential across a ... `) A. 1 B. 2 C. 5 D. 10

A potentiometer having the potential gradient of `2 mV//cm` is used to measure the difference of potential across a resistance of `10 ohm`. If a lengt

Description : A potentiometer having the potential gradient of `2 mV//cm` is used to measure the difference of potential across a resistance of `10 ohm`. If a lengt

Last Answer : A potentiometer having the potential gradient of `2 mV//cm` is used to measure the difference of potential across a ... `) A. 1 B. 2 C. 5 D. 10

Pick up the correct statement from the following: (A) The maximum size of a coarse aggregate, is 75 mm and minimum 4.75 mm (B) The maximum size of the fine aggregate, is 4.75 mm and minimum 0.075 mm (C) The material having particles of size varying from 0.06 mm to 0.002 mm, is known as silt (D) All the ab

Description : Pick up the correct statement from the following: (A) The maximum size of a coarse aggregate, is 75 mm and minimum 4.75 mm (B) The maximum size of the fine aggregate, is 4.75 mm and minimum 0.075 mm ( ... having particles of size varying from 0.06 mm to 0.002 mm, is known as silt (D) All the ab

Last Answer : Answer: Option D

A transformer has a turns ratio of two to one. If a 100 ohm resistor is connected on the high side, its resistance as measured on the low side would be: w) 25 ohms x) 50 ohms y) 100 ohms z) 400 ohms

Description : A transformer has a turns ratio of two to one. If a 100 ohm resistor is connected on the high side, its resistance as measured on the low side would be: w) 25 ohms x) 50 ohms y) 100 ohms z) 400 ohms

Last Answer : ANSWER: W -- 25 OHMS

The effective skin resistance of a material with conductivity 120 and skin depth of 2μm is a) 4.16 kilo ohm b) 4.16 mega ohm c) 41.6 kilo ohm d) 41.6 mega ohm

Description : The effective skin resistance of a material with conductivity 120 and skin depth of 2μm is a) 4.16 kilo ohm b) 4.16 mega ohm c) 41.6 kilo ohm d) 41.6 mega ohm

Last Answer : a) 4.16 kilo ohm

The resistivity of a material with resistance 200 ohm, length 10m and area twice that of the length is a) 200 b) 300 c) 400 d) 500

Description : The resistivity of a material with resistance 200 ohm, length 10m and area twice that of the length is a) 200 b) 300 c) 400 d) 500

Last Answer : c) 400

A cube of wood supporting 200 gm mass just floats in water. When the mass is removed, the cube rises by 2 cm the side of the cube will be a.5 cm b.10 cm c.12.5 cm d.20 cm e.15 cm

Description : A cube of wood supporting 200 gm mass just floats in water. When the mass is removed, the cube rises by 2 cm the side of the cube will be a.5 cm b.10 cm c.12.5 cm d.20 cm e.15 cm

Last Answer : a. 5 cm

A cube of side 5 cm contain a sphere -Maths 9th

Description : A cube of side 5 cm contain a sphere -Maths 9th

Last Answer : Each side of the cube (a) = 5 cm Diameter of the sphere (2r) = 5 cm . ∴ Radius of the sphere (r) = 5/2 cm Volume of the cube = a3 = 53 cm3 = 125 cm3 Volume of the sphere = 4/3 πr3 = 4/3 x ... /2 x 5/2 = 65.476 cm3 Volume of gap between cube and sphere = 125.000 cm3 - 65.476 cm3 = 59.524 cm3

A solid cube of side 12 cm is cut into -Maths 9th

Description : A solid cube of side 12 cm is cut into -Maths 9th

Last Answer : Volume of given cube = a3 = 123 = 12 x 12 x 12 cm3 Let the edge of the new cube = x ∴ Volume of new cube = x3 Volume of 8 new cubes = 8x3 Now, 8x3 = 12 x 12 x 12 ⇒ x 3 = 12 x 12 x 12/8 = 6 3 ⇒ x ... area of new cubes = 6a2/6x2 = 6 x 122/6 x 62 = 6 x 12 x 12/6 x 6 x 6 = 4/1 = 4 : 1

The volume of cube is increasing at a rate of `9 cm^(3)//sec`. Find the rate of increase of its surface area when the side of the cube is 10 cm.

Description : The volume of cube is increasing at a rate of `9 cm^(3)//sec`. Find the rate of increase of its surface area when the side of the cube is 10 cm.

Last Answer : The volume of cube is increasing at a rate of `9 cm^(3)//sec`. Find the rate of increase of its surface area when the side of the cube is 10 cm.

What is the total surface area of cube of side 12 cm?

Description : What is the total surface area of cube of side 12 cm?

Last Answer : It is 12*12*6 = 864 square cm

What is the side length of a cube with a volume of 942 cm cube?

Description : What is the side length of a cube with a volume of 942 cm cube?

Last Answer : It will be the cube root of 942 which is about 9.802803585 cm

Three cubes of side 3 cm. 4 cm, 5 cm respectively are melted to form a new cube. The side of the new cube will be a) 6cm b) 6.5 cm c) 70cm d) 5 cm e) 4.5 cm

Description : Three cubes of side 3 cm. 4 cm, 5 cm respectively are melted to form a new cube. The side of the new cube will be a) 6cm b) 6.5 cm c) 70cm d) 5 cm e) 4.5 cm

Last Answer : a) 6cm

A cuboid shaped wooden block has 6 cm length, 4 cm breadth and 1 cm height. 2. Two faces measuring 4 cm x 1 cm are coloured in black. 3. Two faces measuring 6 cm x 1 cm are coloured in red. 4. Two faces measuring 6 cm x 4 cm are coloured in green. 5. The block is divided into 6 equal cubes of side 1 cm (from 6 cm side), 4 equal cubes of side 1 cm(from 4 cm side). How many cubes having red, green and black colours on at least one side of the cube will be formed?

Description : A cuboid shaped wooden block has 6 cm length, 4 cm breadth and 1 cm height. 2. Two faces measuring 4 cm x 1 cm are coloured in black. 3. Two faces measuring 6 cm x 1 cm are coloured in red. 4. Two faces ... and black colours on at least one side of the cube will be formed? (a)16 (b)12 (c)10 (d)4

Last Answer : Answer key : (d)

How many small cubes each of 96 cm^2 surface area can be formed from the material obtained by melting a larger cube of 384 cm^2 surface area ? -Maths 9th

Description : How many small cubes each of 96 cm^2 surface area can be formed from the material obtained by melting a larger cube of 384 cm^2 surface area ? -Maths 9th

Last Answer : answer:

what is equivalent resistance when four 4 Ohm resistors are connected in i) series ii) parallel

Description : what is equivalent resistance when four 4 Ohm resistors are connected in i) series ii) parallel

Last Answer : equivalent resistance

A 35 V dc supply is connected across a resistance of 600 ohm in series with an unknown resistance R. A

Description : A 35 V dc supply is connected across a resistance of 600 ohm in series with an unknown resistance R. A voltmeter having a resistance of 1.2 kOhm is connected across 600 ohm resistances and reads 5 V. The value of resistance R shall be:

Last Answer : A 35 V dc supply is connected across a resistance of 600 ohm in series with an unknown resistance R. A voltmeter having a resistance of 1.2 kOhm is connected across 600 ohm resistances and reads 5 V. The value of resistance R shall be: 2.4 kOhm

We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance

Description : We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance R.A. voltmeter having a resistance of 1.2 kOhm is connected across 600 Ohm resistance and read 5v. The value of resistance R will be

Last Answer : We connected a 35V dc supply to a resistance of 600 Ohm in series with an unknown resistance R.A. voltmeter having a resistance of 1.2 kOhm is connected across 600 Ohm resistance and read 5v. The value of resistance R will be 2.4 kOhm

A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V,

Description : A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V, variable frequency supply. The current drawn by the circuit is found to be minimum when the supply frequency is 1 kHz. The ... (A) 40, 400 Hz (B) 10, 100 Hz (C) 20, 50 Hz (D) 50, 20 Hz

Last Answer : A coil of inductance 240 mH and resistance 75 Ohm is connected in parallel with a capacitor across a 30 V, variable frequency supply. The current drawn by the circuit is found to be minimum ... supply frequency is 1 kHz. The approximate values of Q-factor and bandwidth are, respectively 20, 50 Hz

A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is ...

Description : A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is (A) 300 W (B) 150 W (C) 45 W (D) 20 W

Last Answer : A d.c. source has an open circuit voltage of 30 V and an internal resistance of 1.5 Ohm. A resistive load is connected to the source. Maximum power dissipated in the load is 150 W

A moving coil instrument of resistance 5 Ohm requires a potential difference of 75 mV to give a full scale...

Description : A moving coil instrument of resistance 5 Ohm requires a potential difference of 75 mV to give a full scale deflection. The value of shunt resistance needed to give a full scale deflection at 30 A is

Last Answer : A moving coil instrument of resistance 5 Ohm requires a potential difference of 75 mV to give a full scale deflection. The value of shunt resistance needed to give a full scale deflection at 30 A is 2.5 milliOhm

A 220 V dc machine has an armature resistance o f 1-ohm. If the full load current is 20A, the difference...

Description : A 220 V dc machine has an armature resistance o f 1-ohm. If the full load current is 20A, the difference in the induced voltage when the machine is running as a motor, and as a generator is

Last Answer : A 220 V dc machine has an armature resistance o f 1-ohm. If the full load current is 20A, the difference in the induced voltage when the machine is running as a motor, and as a generator is 40 V.

Two coils connected in series have resistance of 600 ohm and 300 ohm ...

Description : Two coils connected in series have resistance of 600 ohm and 300 ohm and temperature coefficients of 0.1% and 0.4% respectively.The resistance of the combination at 50oC will be 

Last Answer : Two coils connected in series have resistance of 600 ohm and 300 ohm and temperature coefficients of 0.1% and 0.4% respectively.The resistance of the combination at 50oC will be 990 ohm

A nichrome wire used as heater coil has the resistance of 1 ohm/m. For ...

Description : A nichrome wire used as heater coil has the resistance of 1 ohm/m. For a heater of 1000 W at 200 V, the length of wire required will be 

Last Answer : A nichrome wire used as heater coil has the resistance of 1 ohm/m. For a heater of 1000 W at 200 V, the length of wire required will be 40 m.

A metal resistor has resistance of 10 ohm at 0°C and 11 ohms at 160°C, the temperature coefficient is

Last Answer : A metal resistor has resistance of 10 ohm at 0°C and 11 ohms at 160°C, the temperature coefficient is 0.000625 /°C.

Two 1 kilo ohm, 1/2 W resistors are connected in series. Their combined resistance value and wattage will be

Last Answer : Two 1 kilo-ohm 1/2 W resistors are connected in series. Their combined resistance value and wattage will be 2 kΩ, 1 W.

If resistance is 8 Ohm and current is 16 ampere then what will be the voltage and power?

Description : If resistance is 8 Ohm and current is 16 ampere then what will be the voltage and power?

Last Answer : 128 volts ,2048 watts

Which material is having highest resistivity in ohm-metre at 20oC X10-8?

Description : Which material is having highest resistivity in ohm-metre at 20oC X10-8? A. Mercury B. Iron C. Tungsten D. Silver

Last Answer : Mercury material is having highest resistivity in ohm-metre at 20oC X10-8

Find the dissipation factor when series resistance is 5 ohm and capacitive resistance is 10 unit. a) 2 b) 0.5 c) 1 d) 0

Description : Find the dissipation factor when series resistance is 5 ohm and capacitive resistance is 10 unit. a) 2 b) 0.5 c) 1 d) 0

Last Answer : b) 0.5

Find the time constant in a series R-L circuit when the resistance is 4 ohm and the inductance is 2 H. a) 0.25 b) 0.2 c) 2 d) 0.5

Description : Find the time constant in a series R-L circuit when the resistance is 4 ohm and the inductance is 2 H. a) 0.25 b) 0.2 c) 2 d) 0.5

Last Answer : d) 0.5

50 The equivalent resistance of the primary of the transformer having K = 5, R1 = 0.1 ohm when referred to secondary becomes .....ohm A. 0.5 B. 0.02 C. 0.004 D. 2.5

Description : 50 The equivalent resistance of the primary of the transformer having K = 5, R1 = 0.1 ohm when referred to secondary becomes .....ohm A. 0.5 B. 0.02 C. 0.004 D. 2.5

Last Answer : A. 0.5

An ammeter has a current change of 0—5A and its internal resistance is 0.2 ohm. In order to Change the range

Description : An ammeter has a current change of 0-5A and its internal resistance is 0.2 ohm. In order to Change the range to 0-25 A, wear need to add a resistance of  A) 0.8 ohm in series with the meter B) ... series with the meter C) 0.04 ohm in parallel with the meter D) 0.05 ohm in parallel with the meter

Last Answer : An ammeter has a current change of 0—5A and its internal resistance is 0.2 ohm. In order to Change the range to 0-25 A, wear need to add a resistance of 0.05 ohm in parallel with the meter

The armature resistance of a permanent magnet dc motor is 0.8 Ohm. At no load, the motor draws 1.5 A from

Description : The armature resistance of a permanent magnet dc motor is 0.8 Ohm. At no load, the motor draws 1.5 A from a supply voltage of 25 V and runs at 1500 rpm. The efficiency of the motor while it is operating on load at 1500 ... .5 A from the same source will be  (A) 48.0% (B) 57.1% (C) 59.2% (D) 88.8%

Last Answer : The armature resistance of a permanent magnet dc motor is 0.8 Ohm. At no load, the motor draws 1.5 A from a supply voltage of 25 V and runs at 1500 rpm. The efficiency of the motor while it is operating on load at 1500 rpm drawing a current of 3.5 A from the same source will be 48.0%

The rotor impedance of a slip ring induction motor is (0.1 + j0.6)Ohm/ ph . The resistance/ph to be inserted

Description : The rotor impedance of a slip ring induction motor is (0.1 + j0.6)Ohm/ ph . The resistance/ph to be inserted into rotor to get maximum torque at starting should be

Last Answer : The rotor impedance of a slip ring induction motor is (0.1 + j0.6)Ohm/ ph . The resistance/ph to be inserted into rotor to get maximum torque at starting should be 0.5 Ohm

The bridge most suited for measurement of a four-terminal resistance in the range of 0.001 Ohm to 0.1 Ohm

Description : The bridge most suited for measurement of a four-terminal resistance in the range of 0.001 Ohm to 0.1 Ohm (A) Wien’s bridge (B) Kelvin double bridge (C) Maxwell’s bridge (D) Shering Bridge

Last Answer : The bridge most suited for measurement of a four-terminal resistance in the range of 0.001 Ohm to 0.1 Ohm (A) Wien’s bridge (B) Kelvin double bridge (C) Maxwell’s bridge (D) Shering Bridge

If a wire conductor of 0.2 ohm resistance is doubled in length, its resistance becomes?

Description : If a wire conductor of 0.2 ohm resistance is doubled in length, its resistance becomes?

Last Answer : If a wire conductor of 0.2 ohm resistance is doubled in length, its resistance becomes 0.4 ohm.

The e.m.f. induced in the armature of a shunt generator is 600 V. The armature resistance is 0.1 ohm...

Description : The e.m.f. induced in the armature of a shunt generator is 600 V. The armature resistance is 0.1 ohm. If the armature current is 200 A, the terminal voltage will be?

Last Answer : The e.m.f. induced in the armature of a shunt generator is 600 V. The armature resistance is 0.1 ohm. If the armature current is 200 A, the terminal voltage will be 580 V.

The resistance between the opposite faces of 1m. cube is found to be 1Ω...

Description : The resistance between the opposite faces of 1m. cube is found to be 1Ω . If its length is increased to 2 m, with its volume remaining the same, then its resistance between the opposite faces along its length is : (A) 2 Ω (B) 4 Ω (C) 1 Ω (D) 8 Ω

Last Answer : 4 ohms

Pick up the incorrect statement from the following. For performing compressive strength test of cement (A) Cement and standard sand mortar are used in the ratio of 1 : 3 (B) Water is added at the rate of (P/4) + 3.0 percentage of water where P is the percentage of water for standard consistency (C) A cube mould of 10 cm × 10 cm × 10 cm is used (D) The prepared moulds are kept in a atmosphere of 50% relative humidity

Description : Pick up the incorrect statement from the following. For performing compressive strength test of cement (A) Cement and standard sand mortar are used in the ratio of 1 : 3 (B) Water is added at the ... cm 10 cm is used (D) The prepared moulds are kept in a atmosphere of 50% relative humidity

Last Answer : Answer: Option A

A 100 mL sample of water was treated to convert any iron present to `Fe^(2+)`. Addition of 25 mL of 0.002 M `K_(2)Cr_(2)O_(7)` resulted in the reactio

Description : A 100 mL sample of water was treated to convert any iron present to `Fe^(2+)`. Addition of 25 mL of 0.002 M `K_(2)Cr_(2)O_(7)` resulted in the reactio

Last Answer : A 100 mL sample of water was treated to convert any iron present to `Fe^(2+)`. Addition of 25 ... parts per million (ppm) of iron in the water sample.

What is the Percent notation for 0.002?

Description : What is the Percent notation for 0.002?

Last Answer : Multiply it by 100 to change it into a percentage and so it is0.2%

What is 0.002 in fraction and percent?

Description : What is 0.002 in fraction and percent?

Last Answer : 0.002 is a fraction. It is a fraction in decimal form rather than in the form of a ratio. However, that does not stop it being a fraction. Its rational equivalent is 2/1000 which can be simplified, if required. It is 0.2%.

0.002 is 1/10 of?

Description : 0.002 is 1/10 of?

Last Answer : 0.02

0.002?

Description : 0.002?

Last Answer : Suckkkkkk myyyy headddd