Description : Consider the fractional knapsack instance n = 4, (p1, p2, p3, p4) = (10, 10, 12, 18), (w1, w2, w3, w4) = (2, 4, 6, 9) and M = 15. The maximum profit is given by (Assume p and w denotes profit and weight of objects respectively) (A) 40 (B) 38 (C) 32 (D) 30
Last Answer : (B) 38
Description : A signal is measured at two different points. The power is P1 at the first point and P2 at the second point. The dB is 0. This means________. A) P2 is zero B) P2 equals P1 C) P2 is much larger than P1 D) P2 is much smaller than P1
Last Answer : P2 equals P1
Description : What horse power is required to isothermally compress 800 ft^3 of Air per minute from 14.7 psia to 120 psia? A. 28 hp B.108 hp C.256 hp D.13900 hp Formula: W= p1V1 ln (p1/p2) Power = dW / dt
Last Answer : 108 hp
Description : The total power in both series and parallel circuits is computed with the formula: PT = P1 + P2 + P3 +...Pn. Why can this formula be used for both series and parallel circuits?
Last Answer : In both cases all the power used in the circuit must come from the source.
Description : Two lines L1 and L2 having Parametric equations are P1=[3 4 7]+u[2 2 -6] and P2=[15 -2]+u[1 4 2]. Tangent vector for line L1 a.2i+2j-6k b.2i+2j+6k c.2i-2j-6k d.6-2j-2k
Last Answer : a.2i+2j-6k
Description : Two lines are parallel when a.P1 X P2=0 b.P1 . P2=0 c.P1 = P2 d.P1+ P2=0
Last Answer : a.P1 X P2=0
Description : If f1 and f2 are the distances from the optical centre of a convex lens of focal length to conjugate two points P1 and P2 respectively, the following relationship holds good (A) f = f1 + f2 (B) f = ½ (f1 + f2) (C) 1/f = 1/f1 + 1/f2 (D) None of these
Last Answer : (C) 1/f = 1/f1 + 1/f2
Description : A two stage compressor is used to compress an ideal gas. The gas is cooled to the initial temperature after each stage. The intermediate pressure for the minimum total work requirement should be equal to ... final pressures respectively) (A) Logarithmic (B) Arithmetic (C) Geometric (D) Harmonic
Last Answer : (C) Geometric
Description : Consider a system with twelve magnetic tape drives and three processes P1, P2 and P3. Process P1 requires maximum ten tape drives, process P2 may need as many as four tape drives and P3 may need upto nine ... , system is in: (A) safe state (B) unsafe state (C) deadlocked state (D) starvation state
Last Answer : Answer: B
Description : Find coordinates of points on line having end points P1(3,5,8) and P2 (6,4,3) at u=0.25 a.[3.75 4.25 6.25] b.[3.25 4.25 6.25] c.[3.75 4.75 6.75] d.[4.25 3.75 6.25]
Last Answer : c.[3.75 4.75 6.75]
Description : Find the tangent vector of line having end points P1(3,5,8) and P2 (6,4,3) a.3i+j-5k b.3i-j-5k c.3i-j+5k d.-3i-j-5k
Last Answer : b.3i-j-5k
Description : Write parametric equation of line having end points P1(3,5,8) and P2 (6,4,3). a.[3 5 8]+u[3 -1 -5] b.[3 5 8]+u[3 1 5] c.[3 8 5]+u[3 -1 -5] d.[3 5 8]+u[-3 1 5]
Last Answer : a.[3 5 8]+u[3 -1 -5]
Description : In a 2-D CAD package, clockwise circular arc of radius, 5, specified from P1 (15,10)to P2 (10,15)will have its center at a.(10, 10) b.(15, 10) c.(15, 15) d.(10, 15)
Last Answer : a.(10, 10)
Description : The molecular formula of phosphorus is (a) P1 (b) P2 (c) P3 (d) P4
Last Answer : Ans:(d)
Description : Q No: 251 In a sludge digestion tank if the moisture content of sludge V1 litres is reduced from p1 % to p2 % the volume V2 is A. [(100 + P1)/(100 – P2)] V1 B. [(100 – P1)/(100 + P2)] V1 C. [(100 – P1)/(100 – P2)] V1 D. [(100 + P2)/(100 – P1)] V1
Last Answer : ANS: C
Description : The unit vector to the points p1(0,1,0), p2(1,0,1), p3(0,0,1) is a) (-j – k)/1.414 b) (-i – k)/1.414 c) (-i – j)/1.414 d) (-i – j – k)/1.414
Last Answer : a) (-j – k)/1.414
Description : Find a vector normal to a plane consisting of points p1(0,1,0), p2(1,0,1) and p3(0,0,1) a) –j – k b) –i – j c) –i – k d) –i – j – k
Last Answer : a) –j – k
Description : Find out the price elasticity in the following example : Price Demand 5(P1) 10(Q1) 4(P2) 15(Q2) (a) – 2.5 (b) + 3.5 (c) + 4.0 (d) + 2.5
Last Answer : (a) – 2.5
Description : A short column (30 cm 20 cm) carries a load P1 at 4 cm on one side and another load P2at 8 cm on the other side along a principal section parallel to longer dimension. If the extreme intensity on either side is same, the ... to P2 will be (A) 2/3 (B) 3/2 (C) 8/5 (D) 5/8
Last Answer : (C) 8/5
Description : The expression for entropy change given by, ΔS = - nR ln (P2/P1), holds good for (A) Expansion of a real gas (B) Reversible isothermal volume change (C) Heating of an ideal gas (D) Cooling of a real gas
Last Answer : (B) Reversible isothermal volume change
Description : The expression, ∆G = nRT. ln(P2/P1), gives the free energy change (A) With pressure changes at constant temperature (B) Under reversible isothermal volume change (C) During heating of an ideal gas (D) During cooling of an ideal gas
Last Answer : (A) With pressure changes at constant temperature
Description : The expression, nRT ln(P1/P2), is for the __________of an ideal gas. (A) Compressibility (B) Work done under adiabatic condition (C) Work done under isothermal condition (D) Co-efficient of thermal expansion
Last Answer : C) Work done under isothermal condition
Description : To obtain integrated form of Clausius-Clapeyron equation, ln (P2/P1) = (∆HV/R) (1/T1- 1/T2) from the exact Clapeyron equation, it is assumed that the (A) Volume of the liquid phase is negligible compared to ... gas (C) Heat of vaporisation is independent of temperature (D) All (A), (B) & (C)
Last Answer : (D) All (A), (B) & (C)
Description : According to the American Society of Anesthesiology Physical Status Classification System, a patient with severe systemic disease that is not incapacitating is noted to have physical status ... normal healthy patient d) P2 Classification P2 reflects a patient with mild systemic disease
Last Answer : a) P3 Classification P3 patients are those who have compensated heart failure, cirrhosis, or poorly controlled diabetes, for example.
Description : There are 1.36 kg of gas, for which R = 377 J/kg.k and k = 1.25, that undergo a nonflow constant volume process from p1 = 551.6 kPa and t1 = 60°C to p2 = 1655 kPa. During the process the gas is internally stirred and ... (Formula: T2= T1p2/ p1) a. 999 K b. 888 K c. 456 K d. One of the above
Last Answer : 999 K
Description : What is the resulting pressure when one pound of air at 15 psia and 200 ˚F is heated at constant volume to 800 ˚F? A.15 psia B. 28.6 psia C. 36.4 psia. D. 52.1 psia Formula : T1/p1 = T2/p2 p2= p1T2 / T1
Last Answer : 28.6 psia
Description : Which of the following is the mathematical representation of the Charles’s law? A. V1/V2= P2/P1 B. V1/T1=V2/T2 C. V1/T2=V2/T1 D. V1/V2=√P2/√P1
Last Answer : V1/T1=V2/T2
Description : Which of the following is the Ideal gas law (equation)? A. V/T = K B. V= k*(1/P) C. P1/T1 = P2/T2 D. PV = nRT
Last Answer : PV = nRT
Description : A set of processors P1, P2, ......, Pk can execute in parallel if Bernstein's conditions are satisfied on a pair wise basis; that is P1 || P2 || P3 || ..... || Pk if and only if: (A) Pi || Pj for all i ≠ j (B) Pi || Pj for all i = j+1 (C) Pi || Pj for all i ≤ j (D) Pi || Pj for all i ≥ j
Last Answer : (A) Pi || Pj for all i ≠ j Explanation: Bernstein's Condition: 1. If process Pi writes to a memory cell Mi, then no process Pj can read the cell Mi. 2. If process Pi read from a memory ... Mi. 3. If process Pi writes to a memory cell Mi, then no process Pj can write to the cell Mi.
Description : What steps shall be required to rotate an object about the point P1 (as shown in fig.1) and its placement such that what was at P1 is now reduced and is at P2 (as shown in fig.2). I. Translate P1 to origin II. ... (A) I,II and III (B) II,III and IV (C) I,III and IV (D) All of the above
Last Answer : Answer: Marks given to all
Description : Suppose there are four processes in execution with 12 instances of a Resource R in a system. The maximum need of each process and current allocation are given below: With reference to current allocation, is system safe? If so, ... B) Yes, P1 P2 P3 P4 (C) Yes, P4 P3 P1 P2 (D) Yes, P2 P1 P3 P4
Last Answer : (C) Yes, P4 P3 P1 P2
Description : Consider three CPU intensive processes P1, P2, P3 which require 20, 10 and 30 units of time, arrive at times 1, 3 and 7 respectively. Suppose operating system is implementing Shortest Remaining Time first (preemptive scheduling) ... end of Ready queue are not counted). (A) 3 (B) 2 (C) 4 (D) 5
Last Answer : (A) 3
Description : Consider a system having ‘m’ resources of the same type. These resources are shared by three processes P1, P2 and P3 which have peak demands of 2, 5 and 7 resources respectively. For what value of ‘m’ deadlock will not occur? (A) 70 (B) 14 (C) 13 (D) 7
Last Answer : (B) 14
Description : There are three processes P1, P2 and P3 sharing a semaphore for synchronising a variable. Initial value of semaphore is one. Assume that negative value of semaphore tells us how many processes are waiting in queue. Processes access ... The final value of semaphore will be: (1) 0 (2) 1 (3) -1 (4) -2
Last Answer : Answer: 1
Description : Part of a microwave link can be approximated by free space conditions. The antenna gain are each 40 dB, the frequency is 10 GHz, and the path length is 80 km. Calculate the receive power for a transmitted power of 10 W? A. 0.871 μW B. 871 μW C. 0.871 mW D. 871 nW
Last Answer : A. 0.871 μW
Description : A power station supplies the peak load of 60 Mw, 40 MW and 70 MW to three localities. The annual load factor is 0.50 p.u. and the diversity factor of the load at the station is 1.55. The maximum demand on the station and average load respectively will be
Last Answer : A power station supplies the peak load of 60 Mw, 40 MW and 70 MW to three localities. The annual load factor is 0.50 p.u. and the diversity factor of the load at the station is 1.55. The maximum demand on the station and average load respectively will be 103.2 MW, 51.61 .
Description : For a single mode optical cable with 0.25 dB/km loss, determine the optical power 100 km from a 0.1-mW light source. ∙ A. -45 dBm ∙ B. -15 dBm ∙ C. -35 dBm
Last Answer : ∙ C. -35 dBm
Description : There are 2 plants manufacturing the same product under one corporate management which has decided to merge them. Calculate Break -even point of the merged plant. Particulars Plant I Plant II Capacity operation 100% ... 000 2,40,000 Variable cost 4,40,000 1,80,000 Fixed cost 80,000 50,000simpl
Last Answer : c) Rs 5,00,000
Description : The voltage at the two ends of a transmission line are 132 KV and its reactance is 40 ohm. The Capacity of the line is (A) 435.6 MW (B) 217.8 MW (C) 251.5 MW (D) 500 MW
Last Answer : (A) 435.6 MW
Description : For a 210 MW, turbo-alternator in a thermal power plant, the possible specifications of rotor diameter, stator core length, and number of poles, respectively, are (A) 4.4 m, 1.2 m, 12 (B) 1.2 m, 4.4 m, 2 (C) 4.4 m, 1.2 m, 24 (D) 1.2 m, 4.4 m, 8
Last Answer : For a 210 MW, turbo-alternator in a thermal power plant, the possible specifications of rotor diameter, stator core length, and number of poles, respectively, are 1.2 m, 4.4 m, 2
Description : The output power of a filter is 100 mW, when the signal frequency is 6 kHz. When the frequency is increased to 25 kHz, the output power falls to 50 mW. What is the dB change in power ? (a) -3 dB (b) -5 dB (c) -7 dB (d) -2 dB
Last Answer : The output power of a filter is 100 mW, when the signal frequency is 6 kHz. When the frequency is increased to 25 kHz, the output power falls to 50 mW. What is the dB change in power ? -3 dB
Description : A three phase transmission line delivers a load of 5 MW at 0.8 power factor lagging. Resistance of each conductor is 0.5 ohm / km. Receiving end voltage is 33 kV. If the line loss is not to exceed 10%, determine the length of the line. (A) 7 km (B) 27.9 km (C) 56.8 km (D) 13.9 km
Last Answer : B
Description : A loss less transmission line having Surge Impedance Loading (SIL) of 2280 MW is provided with a uniformly distributed series capacitive compensation of 30%. Then, SIL of the compensated transmission line will be (A) 1835 MW (B) 2280 MW (C) 2725 MW (D) 3257 MW
Last Answer : A loss less transmission line having Surge Impedance Loading (SIL) of 2280 MW is provided with a uniformly distributed series capacitive compensation of 30%. Then, SIL of the compensated transmission line will be 2280 MW
Description : With conventional hydrogen cooling it is possible to increase the rating of a single unit to (a) 50 MW (b) 100 MW (c) 200 MW (d) none ofthe above
Last Answer : (c) 200 MW
Description : A generating station has a maximum demand of 500 MW. The annual load factor is 50 percent. The energy generated per annum will be: A) 2.19 x 106 MWhr B) 600 MWhr C) 250 MWhr D) 7.50 x 106 MWhr
Last Answer : A generating station has a maximum demand of 500 MW. The annual load factor is 50 percent. The energy generated per annum will be: 2.19 x 106 MWhr
Description : A generating station has a maximum demand of 50 Mw, a load factor of 60%, a plant capacity factor of 45% and if the plant while running as per schedule, were fully loaded. The daily energy produced will be
Last Answer : A generating station has a maximum demand of 50 Mw, a load factor of 60%, a plant capacity factor of 45% and if the plant while running as per schedule, were fully loaded. The daily energy produced will be 720 MW.
Description : A generating station has a maximum demand of 30 MW, a load factor of 60% and a plant capacity factor of 50%. The reserve capacity of the plant is (a) 5 MW (b) 4 MW (c) 6 MW (d) 10 MW
Last Answer : A generating station has a maximum demand of 30 MW, a load factor of 60% and a plant capacity factor of 50%. The reserve capacity of the plant is 6 MW
Description : The transfer function of a phase lead compensator is found to be the form (s+z1 ) / (s + p1 ) and that of a lag compensator to be of the form (s+z2 ) / (s + p2 ). Then which of the following conditions must be satisfied? ... (B) z1 > p1 and z2 < p2 (C) z1 < p1 and z2 < p2 (D) z1 < p1 and z2 > p2
Last Answer : A
Description : Tarapur (INDIA) atomic power station (A) Has two boiling water reactors of American design (B) Has an installed capacity of 400 MW (C) Is the first power reactor in India, which became critical in 1969 (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : Two synchronous generators operating in parallel supply a common load of 2.5 MW. The frequency-power characteristics have a common slope of 1 MW/Hz and the no-load frequencies of the generators are 51.5 Hz and 51.0 Hz, ... system frequency is (A) 50 Hz (B) 51 Hz (C) 51.25 Hz (D) 51.5 Hz
Last Answer : Two synchronous generators operating in parallel supply a common load of 2.5 MW. The frequency-power characteristics have a common slope of 1 MW/Hz and the no-load frequencies of the generators are 51.5 Hz and 51.0 Hz, respectively. Then the system frequency is 50 Hz