Kinematic similarity between the model and prototype signifies similarities of a) Motion b) Force c) Length d) None of the above

Kinematic similarity between the model and prototype signifies similarities of  a) Motion  
b) Force  
c) Length  
d) None of the above
by

1 Answer

Answer :

a) Motion
by

Related questions

Dynamic similarity between the model and prototype signifies similarities of a) Motion b) Force c) Length d) None of the above

Description : Dynamic similarity between the model and prototype signifies similarities of a) Motion b) Force c) Length d) None of the above

Last Answer : b) Force

Geometric similarity between the model and prototype signifies similarities of a) Motion b) Force c) Length d) None of the above

Description : Geometric similarity between the model and prototype signifies similarities of a) Motion b) Force c) Length d) None of the above

Last Answer : c) Length

Kinematic index of the straw Walker is as ratio (a) Angular velocity of straw Walker to angular velocity of threshing drum (b) Angular velocity of straw Walker to angular velocity of threshing drum (c) Angular velocity of straw Walker to linear velocity of combine (d) All of the above

Description : Kinematic index of the straw Walker is as ratio (a) Angular velocity of straw Walker to angular velocity of threshing drum (b) Angular velocity of straw Walker to angular velocity of threshing drum (c) Angular velocity of straw Walker to linear velocity of combine (d) All of the above

Last Answer : (a) Angular velocity of straw Walker to angular velocity of threshing drum

The ratio of reel peripheral speed to forward speed of combine is called (a)velocity index (b)angular velocity index (c)reel speed index (d) kinematic index

Description : The ratio of reel peripheral speed to forward speed of combine is called (a)velocity index (b)angular velocity index (c)reel speed index (d) kinematic index

Last Answer : (c)reel speed index

For similarity, in addition to models being geometrically similar to prototype, the following in both cases should also be equal (A) Ratio of inertial force to force due to viscosity (B) Ratio of inertial force to force due to gravitation (C) Ratio of inertial force to force due to surface tension (D) All the four ratios of inertial force to force due to viscosity, gravitation, surface tension, and elasticity

Description : For similarity, in addition to models being geometrically similar to prototype, the following in both cases should also be equal (A) Ratio of inertial force to force due to viscosity (B) ... the four ratios of inertial force to force due to viscosity, gravitation, surface tension, and elasticity

Last Answer : Answer: Option D

Scale up of agitator design requires (A) Geometrical similarity only (B) Dynamic similarity only (C) Both geometrical and dynamic similarity (D) All geometrical, dynamic and kinematic similarity

Description : Scale up of agitator design requires (A) Geometrical similarity only (B) Dynamic similarity only (C) Both geometrical and dynamic similarity (D) All geometrical, dynamic and kinematic similarity

Last Answer : (D) All geometrical, dynamic and kinematic similarity

Frictional force encountered after commencement of motion is called (A) Post friction (B) Limiting friction (C) Kinematic friction (D) Dynamic friction

Description : Frictional force encountered after commencement of motion is called  (A) Post friction  (B) Limiting friction  (C) Kinematic friction  (D) Dynamic friction 

Last Answer : (D) Dynamic friction 

swirl plate in the cone nozzle is provided to. a. Impart rotational motion to the liquid passing through it. b. To increase the droplet size. c. To decrease the droplet size. d. To increase the spray angle.

Description : swirl plate in the cone nozzle is provided to. a. Impart rotational motion to the liquid passing through it. b. To increase the droplet size. c. To decrease the droplet size. d. To increase the spray angle.

Last Answer : a. Impart rotational motion to the liquid passing through it.

Horizontal component of pull perpendicular to the line of motion is called: A.Draft B.Side draft C.Transerve component D. Pull

Description : Horizontal component of pull perpendicular to the line of motion is called: A.Draft B.Side draft C.Transerve component D. Pull

Last Answer : B.Side draft

Needle bearing a roller bearing having a number of smaller diameter roller is well suited to a) Application involving oscillating motion b) Exceptionally high load capacity application at low peripheral speed c) Both (a) and (b) d) None of the above

Description : Needle bearing a roller bearing having a number of smaller diameter roller is well suited to a) Application involving oscillating motion b) Exceptionally high load capacity application at low peripheral speed c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

illage tool moving with uniform velocity is subjected to A)force of gravity. B)pull of power source C)soil reaction. D)all of the above

Description : illage tool moving with uniform velocity is subjected to A)force of gravity. B)pull of power source C)soil reaction. D)all of the above

Last Answer : D)all of the above

Total force exerted upon the implement by a power unit called a)pull. B) draft C)side draft. D)unit draft

Description : Total force exerted upon the implement by a power unit called a)pull. B) draft C)side draft. D)unit draft

Last Answer : a)pull

One of the main advantages of disc brakes over drum brakes is that the disc brake : U. Can stop a vehicle in a shorter distance V. Is more heat resistant W. Weighs less than drum brakes X. Requires less pedal force to stop the vehicle

Description : One of the main advantages of disc brakes over drum brakes is that the disc brake : U. Can stop a vehicle in a shorter distance V. Is more heat resistant W. Weighs less than drum brakes X. Requires less pedal force to stop the vehicle

Last Answer : . Requires less pedal force to stop the vehicle

The force that holds two particles of the different kind together is called as a) Adhesion c) Shear force b) Cohesion d) Compressive

Description : The force that holds two particles of the different kind together is called as a) Adhesion c) Shear force b) Cohesion d) Compressive

Last Answer : a) Adhesion

The force that holds two particles of the same kind together is called as a) Adhesion c) shear force b) cohesion d) compressive

Description : The force that holds two particles of the same kind together is called as a) Adhesion c) shear force b) cohesion d) compressive

Last Answer : b) cohesion

A slat mould board scours better than a solid mould board because of smaller contact area resulting in a) Reduction of adhesive force b) Increase in soil pressure c) Both (a) and (b) d) None of the above

Description : A slat mould board scours better than a solid mould board because of smaller contact area resulting in a) Reduction of adhesive force b) Increase in soil pressure c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

Under a given set of operating conditions, the designer and operator has some control of a)Useful soil resistance b) Parasitic Force c)Draft of implement d) Pull of implement

Description : Under a given set of operating conditions, the designer and operator has some control of a)Useful soil resistance b) Parasitic Force c)Draft of implement d) Pull of implement

Last Answer : b) Parasitic Force

Force ( including rolling resistance friction ) that acts upon the stabilising surfaces such landslide and sole of bottom are called a) Useful soil resistance b) Parasitic force d) Draft of implement. d) Pull of implement

Description : Force ( including rolling resistance friction ) that acts upon the stabilising surfaces such landslide and sole of bottom are called a) Useful soil resistance b) Parasitic force d) Draft of implement. d) Pull of implement

Last Answer : b) Parasitic force

Forces which a tool must overcome in cutting, breaking and moving the soil is called a) Useful soil resistance b) Parasitic force c) Draft of implement d) Pull of implement

Description : Forces which a tool must overcome in cutting, breaking and moving the soil is called a) Useful soil resistance b) Parasitic force c) Draft of implement d) Pull of implement

Last Answer : a) Useful soil resistance

A Tillage implement moving at a constant velocity is subjected to a) Force of gravity b) Soil force (resistance) c) Pull of mower d) All of the above

Description : A Tillage implement moving at a constant velocity is subjected to a) Force of gravity b) Soil force (resistance) c) Pull of mower d) All of the above

Last Answer : d) All of the above

Length of open belt is given by formula a. L=[2C+( 2) (DI+D2)] + [ /4C] b. L=[2C+( 2) (DI+D2)] + [ /4C] c. L=[2C+( 2) (DI+D2)] + [ ] d. L=[2C+( 2) (DI D2)] + [ ]

Description : Length of open belt is given by formula a. L=[2C+( 2) (DI+D2)] + [ /4C] b. L=[2C+( 2) (DI+D2)] + [ /4C] c. L=[2C+( 2) (DI+D2)] + [ ] d. L=[2C+( 2) (DI D2)] + [ ]

Last Answer : a. L=[2C+( 2) (DI+D2)] + [ /4C]

.Increase length of a land slide of a one bottom right hand mould board plough will a) Increase the amount of offset on tractor b) Decrease the amount of offset c) No affect d) Affect Completely

Description : .Increase length of a land slide of a one bottom right hand mould board plough will a) Increase the amount of offset on tractor b) Decrease the amount of offset c) No affect d) Affect Completely

Last Answer : c) No affect

The purpose of registration in a mower is (A) to get uniform length of cut of grass (B)to run the mower at minimum power (C)to run the mower at uniform torque (D)to reduce the occurrence of overload

Description : The purpose of registration in a mower is (A) to get uniform length of cut of grass (B)to run the mower at minimum power (C)to run the mower at uniform torque (D)to reduce the occurrence of overload

Last Answer : (B)to run the mower at minimum power

The size of a seed rill is expressed by: A. Amount of seed sown per unit time. B. Length x width of the machine. C. Area covered per unit time. D. The number of furrow openers x distance between two furrow

Description : The size of a seed rill is expressed by: A. Amount of seed sown per unit time. B. Length x width of the machine. C. Area covered per unit time. D. The number of furrow openers x distance between two furrow

Last Answer : D. The number of furrow openers x distance between two furrow

pecific energy requirement of rotary tillers can be reduce by a) Increasing the bite length b) Decreasing depth to diameter ratio c) Both (a) and (b) d) Excessive reduction in total power requirement

Description : pecific energy requirement of rotary tillers can be reduce by a) Increasing the bite length b) Decreasing depth to diameter ratio c) Both (a) and (b) d) Excessive reduction in total power requirement

Last Answer : c) Both (a) and (b)

Length of cut for silage ranges from E. 2-4 cm F. 5-10 cm G. 15-20 cm H. 20-25 cm

Description : Length of cut for silage ranges from E. 2-4 cm F. 5-10 cm G. 15-20 cm H. 20-25 cm

Last Answer : E. 2-4 cm

345- Excessive stalk deflection particularly when cutting close to ground results in ...... (a) Stubbles of uneven length (b) Increased tedency of stalk to cut by cutting unit..... (c) Less unevenness in cutting (d) Less missing or uncut stalk

Description : 345- Excessive stalk deflection particularly when cutting close to ground results in ...... (a) Stubbles of uneven length (b) Increased tedency of stalk to cut by cutting unit..... (c) Less unevenness in cutting (d) Less missing or uncut stalk

Last Answer : (a) Stubbles of uneven length

A ship whose hull length is 100 m is to travel at 10 m/sec. For dynamic similarity, at what velocity should a 1:25 model be towed through water? (A) 10 m/sec (B) 25 m/sec (C) 2 m/sec (D) 50 m/sec

Description : A ship whose hull length is 100 m is to travel at 10 m/sec. For dynamic similarity, at what velocity should a 1:25 model be towed through water? (A) 10 m/sec (B) 25 m/sec (C) 2 m/sec (D) 50 m/sec

Last Answer : Answer: Option C

A computer model of a part design on a CAD system is called which of the following? a.Computer Prototype b.Geometric Prototype c.Solid Prototype d.Virtual Prototype

Description : A computer model of a part design on a CAD system is called which of the following? a.Computer Prototype b.Geometric Prototype c.Solid Prototype d.Virtual Prototype

Last Answer : d.Virtual Prototype

Choose the correct sequence to generate prototype a.3D CAD data - CAD solid model - STL file - RP prototype b.CAD solid model - 3D CAD data - RP prototype - STL file c.STL file - 3D CAD data - CAD solid model - RP prototype d.3D CAD data - STL file - CAD solid model - RP prototype

Description : Choose the correct sequence to generate prototype a.3D CAD data - CAD solid model - STL file - RP prototype b.CAD solid model - 3D CAD data - RP prototype - STL file c.STL file - 3D CAD data - CAD solid model - RP prototype d.3D CAD data - STL file - CAD solid model - RP prototype

Last Answer : a.3D CAD data - CAD solid model - STL file - RP prototype

What is a model of a proposed product, service, or system? a. Prototyping b. Prototype c Selling prototype d. None of the above

Description : What is a model of a proposed product, service, or system? a. Prototyping b. Prototype c Selling prototype d. None of the above

Last Answer : d. None of the above

What is the advantage of using prototype software development model instead of waterfall model? Also explain the effect of defining a prototype on the overall cost of the software project?

Description : What is the advantage of using prototype software development model instead of waterfall model? Also explain the effect of defining a prototype on the overall cost of the software project?

Last Answer : Ans:The waterfall model: This is the classic SDLC model, with a linear and sequential method that has goals for each development phase. The waterfall model simplifies task scheduling, because ... acceptable prototype is finally achieved from which the complete system or product can now be developed.

What is a model of a proposed product, service, or system? a. Prototyping b. Prototype c. Proof‐of‐concept prototype d. Selling prototype

Description : What is a model of a proposed product, service, or system? a. Prototyping b. Prototype c. Proof‐of‐concept prototype d. Selling prototype

Last Answer : b. Prototype

The quick design of a software that is visible to end users leads to ............ (A) iterative model (B) prototype model (C) spiral model (D) waterfall model

Description : The quick design of a software that is visible to end users leads to ............ (A) iterative model (B) prototype model (C) spiral model (D) waterfall model 

Last Answer : (B) prototype model

The maximum frictional force which comes into play when a body just begins to slide over another surface is called (A) Limiting friction (B) Sliding friction (C) Rolling friction (D) Kinematic friction

Description : The maximum frictional force which comes into play when a body just begins to slide over another surface is called (A) Limiting friction (B) Sliding friction (C) Rolling friction (D) Kinematic friction

Last Answer : (A) Limiting friction

verticalsuctioninmouldboardploughis______whereashorizontalsuctionis______

Description : verticalsuctioninmouldboardploughis______whereashorizontalsuctionis______

Last Answer : .0.3to0.5cm,0.5cm

Byincreasingdiskangle,depthpenetration_____beoverwithofcut_______

Description : Byincreasingdiskangle,depthpenetration_____beoverwithofcut_______

Last Answer : .decreases,increases

A paddy transplanter uses either root wash type seedlings or __________ seedlings.

Description : A paddy transplanter uses either root wash type seedlings or __________ seedlings.

Last Answer : soil bearing

An indigenous plough cuts a _________furrow cross sect

Description : An indigenous plough cuts a _________furrow cross sect

Last Answer : Trapizoidal

The unit of filter medium resistance is________

Description : The unit of filter medium resistance is________

Last Answer : L^-1

The average working speed of a hand operated chaff fitted with two knives is _________ rev/min.

Description : The average working speed of a hand operated chaff fitted with two knives is _________ rev/min.

Last Answer : 35

In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.

Description : In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.

Last Answer : 1200 to 1500

In sprayers , operating pressures below ___________Kpa are undesirable for hydraulic nozzles other than flooding type

Description : In sprayers , operating pressures below ___________Kpa are undesirable for hydraulic nozzles other than flooding type

Last Answer : 140

Optimum speed for grains like gram,pea,etc.,thresher using power is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Description : Optimum speed for grains like gram,pea,etc.,thresher using power is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Last Answer : a) 300-400rpm

Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Description : Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm

Last Answer : d) 1100-1200rpm

Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm

Description : Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm

Last Answer : c) 600-800rpm

Air output of a duster is given by formula a) Q= 60×A×V b)Q= 60×A×(2GH/Y) c) Q= 240×A×h d) all of the above

Description : Air output of a duster is given by formula a) Q= 60×A×V b)Q= 60×A×(2GH/Y) c) Q= 240×A×h d) all of the above

Last Answer : d) all of the above

Lewis formula is used in the design of a) gears b) clutch c) chain drive d) belt drives

Description : Lewis formula is used in the design of a) gears b) clutch c) chain drive d) belt drives

Last Answer : a) gears

Transplanter using soil bearing seedlings are more popular than washed root seedling transplanter because of a) less labour requirement b) lesser plant missing percentage c) higher work rates d) all of the above

Description : Transplanter using soil bearing seedlings are more popular than washed root seedling transplanter because of a) less labour requirement b) lesser plant missing percentage c) higher work rates d) all of the above

Last Answer : d) all of the above