Description : thresher causes more seed damage if: a speed is increased b clearance increased c speed is decreased d feed rate is reduced
Last Answer : a speed is increased
Description : The thresher caused More seed damage if A. Speed is increases B. Clearance is increase C. Feed rate is reduced. D. Speed is reduced
Last Answer : Speed is increases
Description : A thresh causes more seed damage if :- a. Seed is increase b. Clearance is increased c. Feed rate is reduced d. Seed is reduced
Last Answer : a. Seed is increase
Description : The threshing efficiency of thresher depends on a) Cylinder peripheral speed b) Cylinder concave clearance c) Feed rate, moisture content and type of crop d) All are correct
Last Answer : All are correct
Description : Thresher blows broken grains with chaff due to a) Higher cylinder speed. b) More feed Rate c) More cylinder concave clearance d) Moisture content of the crop is more
Last Answer : a) Higher cylinder speed.
Description : Cylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peCylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peripheral speed N. Concave clearance O. Blower speed P. All of the above
Last Answer : M. Cylinder peripheral speed
Description : Crop factors which affecting thresher preformation. a) Variety of crop, Moisture in crop material b) Feeding chute angle, cylinder types c) Cylinder speed, feed rate d) Cylinder type, feed rate
Last Answer : Variety of crop, Moisture in crop material
Description : Operational factors which affecting thresher preformation. a) Variety of crop, Moisture in crop material b) Feeding chute angle, cylinder type c) Cylinder speed, feed rate d) Cylinder type ,feed rate
Last Answer : Cylinder speed, feed rate
Description : Machine factors which affecting thresher preformation. a) Variety of crop, Moisture in crop material b) Feeding chute angle, cylinder type c) Cylinder speed, feed rate d) Cylinder type ,feed rate
Last Answer : Feeding chute angle, cylinder type
Description : In a thresher, by increasing the speed of threshing cylinder a) Threshing efficiency can be increased b) Broken grain loss can be minimized c) Un-threshed grains can be increased d) Straw breakup can be increased Ans. a
Last Answer : ans a
Description : Adjustment needed when thresher blows grains with chaff a.) Decreasing cylinder peripheral speed. b.) Increasing cylinder speed. c.) Decreasing feed rate. d.) Increasing cylinder
Last Answer : a.) Decreasing cylinder peripheral speed.
Description : A large clearance volume in a reciprocating compressor results in A. Reduced volume flow rate B. Increased volume flow rate C. Lower suction pressure D. Lower delivery pressure
Last Answer : ANSWER : A
Description : A large clearance volume in reciprocating compressor results in A. reduced volume flow rate B. Increased volume flow rate C. Lower suction pressure D. Lower delivery pressure
Description : The seed rate can be increased by a) Decreasing the exposure length b) Increasing the exposure length c) Increasing speed d) Decreasing speed Ans. b
Last Answer : ans b
Description : Increasing non grain feed rate increase (a) Cylinder losses (b) Seed damage (c) Both (a) and(b) (d) None of the above
Last Answer : (a) Cylinder losses
Description : Increasing non-grain feed rate increase a) Cylinder losses b) seed damage c)Both (a) and (b) d) none of the above
Last Answer : a) Cylinder losses
Description : In case of a hammer crusher, the final product size depends on the (A) Feed rate (B) Rotor speed (C) Clearance between hammer & grinding plates (D) All (A), (B) and (C
Last Answer : (D) All (A), (B) and (C
Description : Most important factor affecting threshing efficiency a)peripheral speed of the drum b)cylinder concave clearance c)moisture content of crop d)feed rate
Last Answer : a)peripheral speed of the drum
Description : Working width of disc plough can be increased by a) Disc angle b) Gang angle c) Vertical suction d) Horizontal clearance Ans. a
Description : It is a machine designed for harvesting ,threshing,separating, cleaning and collecting grains while moving through standing crops. a. Weeder b. thresher d. None of above
Last Answer : Ans- c. COMBINE
Description : This type thresher consists of a flywheel with corrugation on its periphery and sides. Rims of flywheel fitted with chopping blades. b. Axial flow c. Dummy d. None of above
Last Answer : Ans- a. Syndicator
Description : This type thresher consists of corrugated bars are mounted axially on pheripheri of the cylinder. a. Hammer mill c. Dummy d. None of above
Last Answer : Ans- b. Raspbar
Description : This type thresher consists of beater mounted on a shaft which rotates inside a closed casing and concave. a. Hammer mill b. Spike tooth d. None of above
Last Answer : Ans- c. Dummy
Description : Different parts of Thresher are A) Feeding device B) Threshing cylinder C) Concave D) All of the above.
Last Answer : All of the above.
Description : The Japanese type rotary thresher is used for threshing a) Paddy b) Wheat c) Sunflower d) Safflower
Last Answer : Paddy
Description : The spacing between two adjacent discs in Olpad thresher is a) 5 cm b) 10 cm c) 15 cm d) 20 cm
Last Answer : 15 cm
Description : A multi type thresher is equipped with a) Spike tooth cylinder b) Rasp bar cylinder c) Hammer mill cylinder d) All of the above
Last Answer : All of the above
Description : The dummy type thresher is also termed as a) Rasp bar type thresher b) Hammer mill type thresher c) Spike tooth type thresher d) Syndicator tooth type thresher
Last Answer : Hammer mill type thresher
Description : machine designed for harvesting, threshing , cleaning and collecting grains while moving through standing crops. a) Combine b) Self operated VCR c) Power roller thresher d) Post harvesting technology
Last Answer : Combine
Description : This type seed metering mechanism consist of wheel with fine and coarse ribbed flanges. b. fluted feed c. Cup feed d. None of the above
Last Answer : Ans - a. Internal double run
Description : For sowing of wheat seed, a suitable metering mechanism is: A. Cup feed B. Cell feed C. Fluted roller D. Brush feed
Last Answer : Fluted roller
Description : is the type of seed metering mechanism. a) Fluted feed type b) Cup feed type c) Brush feed mechanism d) All of above
Last Answer : All of above
Description : In cup food metering device, the seed rate is controlled by: A. Shaft rotation B. Speed of machine C. Size of cups D. All are correct
Last Answer : Size of cups
Description : From which of the following is benefit of computer integrated manufacturing(CIM). a.Reduced lead time b.Increased production time c.Reduced productivity d.All of the above
Last Answer : a.Reduced lead time
Description : Form which of the following is the objective of cellular manufacturing. a.Reduced manufacturing lead time b.Increased in quality c.Reduced setup time d.All of the above
Last Answer : d.All of the above
Description : An ideal gas is maintained at constant temperature. If the pressure on the gas is doubled, the volume is a. increased fourfold b. doubled c. reduced by half d. decreased by a quarter
Last Answer : reduced by half
Description : Optimum speed for grains like gram,pea,etc.,thresher using power is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm
Last Answer : a) 300-400rpm
Description : Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm
Last Answer : d) 1100-1200rpm
Description : Increasing the cylinder speed result in (a) Increase threshing efficiency (b) Reduce cylinder loss (c) Increase seed damage (d) All of the above
Last Answer : (a) Increase threshing efficiency
Description : Increasing the cylinder speed result in a) Increase threshing efficiency b) Reduce cylinder loss c) Increase seed damage d) All of the above
Last Answer : d) All of the above
Description : Unnecessary and frequent applications of varnish to the generator windings to repair defective insulation will result in ____________. A. heavy coatings of varnish interfering with heat dissipation B. ... of the rectifier assembly D. a built-up of varnish without changing generator operation
Last Answer : Answer: A
Description : 60-year-old patient with creatinine clearance 50 ml/min has to be treated with gentamicin. His daily dose of gentamicin should be reduced to the following percentage of the usual adult dose: A. 70% B. 50% C. 40% D. 30%
Last Answer : B. 50%
Description : A 60-year-old patient with creatinine clearance 50 ml/min has to be treated with gentamicin. His daily dose of gentamicin should be reduced to the following percentage of the usual adult dose: A. 70% B. 50% C. 40% D. 30%
Description : In patients with renal insufficiency the clearance of the following drug is reduced parallel to the reduction in creatinine clearance: A. Propranolol B. Digoxin C. Lignocaine D. Verapamil
Last Answer : B. Digoxin
Description : An environment which is increasingly complex and turbulent displays: A. More orderly competition. B. A reduced risk of product obsolescence. C. More predictable demand. D. Increased speed of innovation.
Last Answer : Increased speed of innovation.
Last Answer : More orderly competition.
Description : Which of the following statements describes the significance of ambient temperature in relation to the service life of electronic components? A. Ambient temperature should be as high as possible to drive ... is kept low. D. A reduced ambient temperature causes a corresponding reduced service life.
Last Answer : Answer: B
Description : To give the best obstacle clearance on take-off, take-off should be made with: a. Flaps partially extended and at best rate of climb speed (Vy) b. Flaps partially extended and at best angle of climb ... at best rate of climb speed (Vy) d. Flaps retracted and at best angle of climb speed (Vx)
Last Answer : d. Flaps retracted and at best angle of climb speed (Vx)
Description : The function of the autotransformers used with the starters of large AC motors is to provide _____________. A. increased voltage for starting B. increased torque for starting C. reduced voltage for starting D. speed control
Last Answer : Answer: C