Description : Increasing the cylinder speed result in (a) Increase threshing efficiency (b) Reduce cylinder loss (c) Increase seed damage (d) All of the above
Last Answer : (a) Increase threshing efficiency
Description : Most important factor affecting threshing efficiency a)peripheral speed of the drum b)cylinder concave clearance c)moisture content of crop d)feed rate
Last Answer : a)peripheral speed of the drum
Description : Increasing non grain feed rate increase (a) Cylinder losses (b) Seed damage (c) Both (a) and(b) (d) None of the above
Last Answer : (a) Cylinder losses
Description : Increasing non-grain feed rate increase a) Cylinder losses b) seed damage c)Both (a) and (b) d) none of the above
Last Answer : a) Cylinder losses
Description : In a thresher, by increasing the speed of threshing cylinder a) Threshing efficiency can be increased b) Broken grain loss can be minimized c) Un-threshed grains can be increased d) Straw breakup can be increased Ans. a
Last Answer : ans a
Description : Optimum operating cylinder speed for wheat threshing using power operated thresher is a) 300-400rpm b) 400-600rpm c) 600-800rpm d) 1100-1200rpm
Last Answer : d) 1100-1200rpm
Description : A threshing cylinder of 15cm radius is rotating at 700rpm if peripheral velocity (m/sec) will be a. 11 b.105 c. 210 d. 660
Last Answer : a. 11
Description : Cylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peCylinder loss in a stationary power thresher can be reduced by increasing the : M. Cylinder peripheral speed N. Concave clearance O. Blower speed P. All of the above
Last Answer : M. Cylinder peripheral speed
Description : Differential lock offers advantage of E. Threshing efficiency of thresher (power operated) F. Capacity of chaff cutters G. Cleaning capacity of straw walkers H. None of the above
Last Answer : F. Capacity of chaff cutters
Description : Free (threshed) seed carried over the straw discharged from the rear shoe is called as (a) Cylinder loss (b)walker loss (rack Loss) (b) Shoe loss (d) gathering loss
Last Answer : (b) Shoe loss
Description : Free (threshed) seed carried over the walker or rack in straw and discharge from the rear of machine is called as (a) Cylinder loss (b) walker loss(rack loss) (c) Shoe loss (d) gathering loss
Last Answer : (b) walker loss(rack loss)
Description : Unthreshed seed discharged from the rear of the machine either in straw or in the material from the cleaning shoe is called (a)cylinder loss (b)walker loss (rack loss) (c)shoe loss (d) gathering loss
Last Answer : (a)cylinder loss
Description : Adjustment needed when thresher blows grains with chaff a.) Decreasing cylinder peripheral speed. b.) Increasing cylinder speed. c.) Decreasing feed rate. d.) Increasing cylinder
Last Answer : a.) Decreasing cylinder peripheral speed.
Description : iesel engine has less reserve torque then spark ignition because ∙ Torque-speed curve is governed by volumetric efficiency of fuel pump and engine cylinder ∙ Torque is a function of thermal efficiency ∙ Diesel engine has generally low speed engine ∙ None of the above
Last Answer : ∙ Torque is a function of thermal efficiency
Description : A thresh causes more seed damage if :- a. Seed is increase b. Clearance is increased c. Feed rate is reduced d. Seed is reduced
Last Answer : a. Seed is increase
Description : The threshing efficiency of thresher depends on a) Cylinder peripheral speed b) Cylinder concave clearance c) Feed rate, moisture content and type of crop d) All are correct
Last Answer : All are correct
Description : Reaper is used for a.) Plowing b.) Harvesting and threshing. c.) Cutting crops. d.) Cutting and windrow.
Last Answer : d.) Cutting and windrow.
Description : A reaper used for : a. Cutting crop b. Cutting and windrewing c. Cutting and threshing d. None of these
Last Answer : b. Cutting and windrewing
Description : Kinematic index of the straw Walker is as ratio (a) Angular velocity of straw Walker to angular velocity of threshing drum (b) Angular velocity of straw Walker to angular velocity of threshing drum (c) Angular velocity of straw Walker to linear velocity of combine (d) All of the above
Last Answer : (a) Angular velocity of straw Walker to angular velocity of threshing drum
Description : Seed damage due to cut-off not a problem in (a) Horizontal plate metering mechanism (b) Vertical plate metering mechanism (c) Both (a) and (b) (d) Inclined plate metering mechanism
Last Answer : (d) Inclined plate metering mechanism
Description : pecific energy requirement of rotary tillers can be reduce by a) Increasing the bite length b) Decreasing depth to diameter ratio c) Both (a) and (b) d) Excessive reduction in total power requirement
Last Answer : c) Both (a) and (b)
Description : 349- Pods, heads or ears & freeseeds, lost during the cutting & conveying operation are called as..... (a) Cylinder loss (b) Walker losses ( rack loss) (c) Shoe losses (d) Gathering loss
Last Answer : (d) Gathering loss
Description : In a combine harvester the peripheral speed of the cylinder ranges between ________ m/min.
Last Answer : 1200 to 1500
Description : Optimum operating cylinder speed for the power operated maize sheller is a) 200-400rpm b) 400-600rpm c) 600-800rpm d) 1000-1200rpm
Last Answer : c) 600-800rpm
Description : Thresher blows broken grains with chaff due to a) Higher cylinder speed. b) More feed Rate c) More cylinder concave clearance d) Moisture content of the crop is more
Last Answer : a) Higher cylinder speed.
Description : .total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above
Last Answer : .total grain loss in a combine increase with a. increase in forward speed b. decrease in stubble Hight c. increase in concave clearance d. all of the above
Description : Increasing the grain/non-grain ratio on shoe tends to _________ the shoe losses a) Decrease b) Increase c)Decrease or increase d) Equal
Last Answer : c)Decreas
Description : Rated speed of an engine is the speed at which an engine devlopes (A) Maximum crankshaft torque (B) Maximum brake horse power output (C) Maximum thermal efficiency (D) Maximum drawback pull
Last Answer : (B) Maximum brake horse power output
Description : Formula for established plants to the speed sown based on the dug seed is given by A. CI= [(E×10000) /(D×W) ]×1000 B. CI=[E/(N+E) ]×100 C.Both (A) and (B) D. None of (A) and (B)
Last Answer : B. CI=[E/(N+E) ]×100
Description : An animal drawn seed drill has k number of furrow openers 180mm apart. If the speed of operation is 2.0kmph, the area covered (ha), in 8-11day is given by: A. 1.85/1000k B. 28.8 x 10-2k C. k/6.56 D. 1.762k
Last Answer : B. 28.8 x 10-2k
Description : An animal drawn seed drill has k number of furrow openers 180mm apart. If the speed of the operation is 2.0kmph then the area covered (ha), in 8 hr day is given by: a) 1.85/1000k b) 28.8 * 10-2k c) k/6.456 d) 1.762k
Last Answer : b) 28.8 * 10-2k
Description : Cell fill is affected by (a) Seed size (b) Cell speed (c) Cell size (d) All of the above
Last Answer : d) All of the above
Description : The average spacing of seeds or hills in field is obtained or determined by a) The ratio of linear or peripheral speed of seed pick up units (cells fingers, etc) to the forward speed of the planter b) The distance ... up units (cells) on the metering unit c) Both (a) and (b) d) None of the above
Description : 310- Larger tension ratio result in... (a) Unnecessary high tension in belt (b) Reduction in belt life (c) Excessive belt slippage (d) Increase belt life
Last Answer : (c) Excessive belt slippage
Description : To separate grains from the harvested crop and provide clean grain without much loss and damage which called as A) Potato digger elevator B) Groundnut digger shaker C) Reaper binder D) Threshing
Last Answer : Threshing
Description : .When the valves are carried in engine bioel at one side of each cylinder is called A. Valves in head arrangements B. L-head C. I-head D. None of the above
Last Answer : B. L-head
Description : An engine is called I or valve in head engine when a) Valve are immediately above the cylinder b) Both valves are on one side c) Both valves are on opposite direction d) None of the above
Last Answer : d) None of the above
Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type c) Spike tooth d) Hammer mill
Last Answer : a) Raspbar type cylinder
Description : The two types of cylinder used on power wheat threshers are: a) Serrated disc and rasp bar b) Spike tooth and wire loop type c) Spike tooth and hammer mill d) Hammer mill and flails
Last Answer : c) Spike tooth and hammer mill
Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type cylinder c) Spike tooth d) Hammer mill
Description : Axial flow thresher utilises (a) Rasp bar cylinder (b) Spike tooth cylinder (c) Hammer mill cylinder (d) Peg tooth cylinder
Last Answer : (b) Spike tooth cylinder
Description : Compression pressure in petrol engine cylinder is a) 6-10 kg/cm2 b) 10-20 kg/cm2 c) 20-35 kg/cm2 d) 35-40 kg/cm2
Last Answer : a) 6-10 kg/cm2
Description : Compression pressure in diesel engine cylinder is a) 6-10 kg/cm2 b) 10-20 kg/cm2 c) 20-35 kg/cm2 d) None of the above
Last Answer : c) 20-35 kg/cm2
Description : Firing order of a six cylinder engine in which no two adjacent cylinder have power stroke is (a) 1 5 3 6 2 4 (b) 1 2 3 4 5 6 (c) 1 5 4 6 3 2 (d) 1 4 2 5 6 3
Last Answer : (a) 1 5 3 6 2 4
Description : hen displacement volume is divided by piston displacement, what will we obtained (a) number of cylinders (b) number of power stroke per minute for all cylinders (c) number of revolution of the crankshaft (engine) (d) number of revolution of crankshaft × number of cylinder
Last Answer : (b) number of power stroke per minute for all cylinders
Description : Durability of the fertilizer increases with a) Increase in the kinetic angle of repose b) Decrease in the kinetic angle of repose c) Decrease in the speed of the forward travel d) None of the above
Last Answer : b) Decrease in the kinetic angle of repose
Description : raft increases with increase in forward speed for most of the implement, mainly due to a) More rapid acceleration of any soil particles that is moved appreciably b) More working width c) Increased working depth d) Draft decreases with increase in speed of implement
Last Answer : a) More rapid acceleration of any soil particles that is moved appreciably
Description : knives of the cutter bar are scrratedin order to a)Increase the co-efficient of friction between crop stalk machine b)Reducing the deflection of stalk side ways c)To increase the cutting speed d)To improve cutting height
Last Answer : a)Increase the co-efficient of friction between crop stalk machine
Description : Width of cut of disc plow is increased by a)Increasing disc angle b)Increasing tilt angle c)addition of more weight d)Decreasing disc angle
Last Answer : a)Increasing disc angle
Description : Volumetric efficiency is affected by (A) Turbulence velocity and temperature of intake manifold (B) Efficiency of exhaust stroke (C) Valve timing overlap (D) All the above
Last Answer : (D) All the above