Percentage elongation during tensile test is indication of (a) Ductility (b) Malleability (c) Creep (d) Rigidity

Percentage elongation during tensile test is indication of
(a) Ductility
(b) Malleability
(c) Creep
(d) Rigidity
by

1 Answer

Answer :

(a) Ductility
by

Related questions

The percentage elongation and the percentage reduction in area depends upon (a) Tensile strength of the material (b) Ductility of the material (c) Toughness of the material (d) None of these

Description : The percentage elongation and the percentage reduction in area depends upon (a) Tensile strength of the material (b) Ductility of the material (c) Toughness of the material (d) None of these

Last Answer : B

The property of a material by which it can be drawn to a smaller section by applying a tensile load is called (a) Elasticity (b) Plasticity (c) Ductility (d) Malleability

Description : The property of a material by which it can be drawn to a smaller section by applying a tensile load is called (a) Elasticity (b) Plasticity (c) Ductility (d) Malleabilityy

Last Answer : (c) Ductility

Percentage elongation of a material is a measure of its (A) Ductility (B) Brittleness (C) Toughness (D) Malleability

Description : Percentage elongation of a material is a measure of its (A) Ductility (B) Brittleness (C) Toughness (D) Malleability

Last Answer : (A) Ductility

The property of the material which allows it to be drawn into smaller section (a) Plasticity (b) Ductility (c) Elasticity (d) Malleability

Description : The property of the material which allows it to be drawn into smaller section (a) Plasticity (b) Ductility (c) Elasticity (d) Malleability

Last Answer : (b) Ductility

The property of a material by which it can be beaten or rolled into thin sheets, is called (a) Elasticity (b) Plasticity (c) Ductility (d) Malleability

Description : The property of a material by which it can be beaten or rolled into thin sheets, is called (a) Elasticity (b) Plasticity (c) Ductility (d) Malleability

Last Answer : (d) Malleability

The shafts are designed on the basis of a. strength and rigidity. b. ductility. c. malleablility. d. resilience.

Description : The shafts are designed on the basis of a. strength and rigidity. b. ductility. c. malleablility. d. resilience.

Last Answer : a. strength and rigidity.

Young's modulus of a material is the measure of its (A) Stiffness (B) Malleability (C) Creep resistance (D) Tensile strength

Description : Young's modulus of a material is the measure of its (A) Stiffness (B) Malleability (C) Creep resistance (D) Tensile strength

Last Answer : Option A

Cast iron has (A) Very high tensile strength (B) High ductility (C) High malleability (D) Elastic limit close to ultimate breaking strength

Description : Cast iron has (A) Very high tensile strength (B) High ductility (C) High malleability (D) Elastic limit close to ultimate breaking strength

Last Answer : (D) Elastic limit close to ultimate breaking strength

Copper has very low (A) Malleability (B) Ductility (C) Tensile strength (D) Thermal & electrical conductivity

Description : Copper has very low (A) Malleability (B) Ductility (C) Tensile strength (D) Thermal & electrical conductivity

Last Answer : (C) Tensile strength

Cast iron has (A) High ductility (B) High malleability (C) Very high tensile strength (D) Its elastic limit very close to ultimate breaking strength

Description : Cast iron has (A) High ductility (B) High malleability (C) Very high tensile strength (D) Its elastic limit very close to ultimate breaking strength

Last Answer : (D) Its elastic limit very close to ultimate breaking strength

The property due to which a metal can be hammered into thin sheets without breaking is _______. a) malleability b)ductility c)tensile strength d)conductivity

Description : The property due to which a metal can be hammered into thin sheets without breaking is _______. a) malleability b)ductility c)tensile strength d)conductivity

Last Answer : a) malleability

Modulus of rigidity is (a)Tensile stress / Tensile strain (a)Shear stress / Shear strain (a)Tensile stress / Shear strain (a)Shear stress / Tensile strain

Description : Modulus of rigidity is (a)Tensile stress / Tensile strain (a)Shear stress / Shear strain (a)Tensile stress / Shear strain (a)Shear stress / Tensile strain

Last Answer : (a)Shear stress / Shear strain

In an all weld tensile test, the original specimen gauge length was 50mm, and after the test the increased gauge length was 65mm, what is the elongation percentage? a) % A is 40 b) % A is 60 c) % A is 30 d) % A is 36

Description : In an all weld tensile test, the original specimen gauge length was 50mm, and after the test the increased gauge length was 65mm, what is the elongation percentage? a) % A is 40 b) % A is 60 c) % A is 30 d) % A is 36

Last Answer : c) % A is 30

Brittleness is opposite to (a) Toughness (b) Plasticity (c) Malleability (d) None of these

Description : Brittleness is opposite to (a) Toughness (b) Plasticity (c) Malleability (d) None of these

Last Answer : b) Plasticity

The ability of the material to deform without breaking is called (a) Elasticity (b) Plasticity (c) Creep (d) None of these

Description : The ability of the material to deform without breaking is called (a) Elasticity (b) Plasticity (c) Creep (d) None of these

Last Answer : (b) Plasticity

A helical spring is fabricated by wrapping wire 19.05 mm in diameter around a forming cylinder 203.2 mm in diameter. Compute the number of turns required to permit an elongation of 101.6 mm. without exceeding a shearing stress of 124 N/mm2. G = 82737 N/mm2. a. 10 turns b. 20 turns c. 25 turns d. 30 turns

Description : A helical spring is fabricated by wrapping wire 19.05 mm in diameter around a forming cylinder 203.2 mm in diameter. Compute the number of turns required to permit an elongation of 101.6 mm. without exceeding a shearing ... G = 82737 N/mm2. a. 10 turns b. 20 turns c. 25 turns d. 30 turns

Last Answer : a. 10 turns

Determine the maximum shearing stress and elongation in a helical steel spring composed of 20 turns of 20-mm-diameter wire on a mean radius of 90 mm when the spring is supporting a load of 1.5 kN. and G = 83 GPa. a. 200 mm b. 105.4 mm c. 150 mm d. 250 mm

Description : Determine the maximum shearing stress and elongation in a helical steel spring composed of 20 turns of 20-mm-diameter wire on a mean radius of 90 mm when the spring is supporting a load of 1.5 kN. and G = 83 GPa. a. 200 mm b. 105.4 mm c. 150 mm d. 250 mm

Last Answer : b. 105.4 mm

Shear stress causes (a) Deformation (b)Elongation (c) Contraction (d) None

Description : Shear stress causes (a) Deformation (b)Elongation (c) Contraction (d) None

Last Answer : (d) None

The length of a wire is increased by 1 mm on the application of a certain load. In a wire of the same material but of twice the length and half the radius, the same force will produce an elongation of (a) 0.5 mm (b) 2 mm (c) 4 mm (d) 8 mm

Description : The length of a wire is increased by 1 mm on the application of a certain load. In a wire of the same material but of twice the length and half the radius, the same force will produce an elongation of (a) 0.5 mm (b) 2 mm (c) 4 mm (d) 8 mm

Last Answer : (d) 8 mm

Elongation of a bar of uniform cross section of length ‘L’, due to its own weight ‘W’ is given by a. 2WL/E b. WL/E c. WL/2E d. WL/3E Where, E=Young’s modulus of elasticity of material

Description : Elongation of a bar of uniform cross section of length ‘L’, due to its own weight ‘W’ is given by a. 2WL/E b. WL/E c. WL/2E d. WL/3E Where, E=Young’s modulus of elasticity of material

Last Answer : c. WL/2E

The value of Poison’s ratio depends upon (a) Nature of load, tensile or compressive (b) Magnitude of load (c) Material of the test specimen (d) Dimensions of the test specimen

Description : The value of Poison’s ratio depends upon (a) Nature of load, tensile or compressive (b) Magnitude of load (c) Material of the test specimen (d) Dimensions of the test specimen

Last Answer : (c) Material of the test specimen

With increase in the carbon percentage in the steel, its (A) Hardness increases (B) Ductility reduces (C) Tensile strength increases (D) All (A), (B) and (C)

Description : With increase in the carbon percentage in the steel, its (A) Hardness increases (B) Ductility reduces (C) Tensile strength increases (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In case of brasses, with decreasing zinc percentage and increasing copper percentage, its __________ increases. (A) Percentage elongation (B) Brinell hardness (C) Tensile strength (D) All 'a', 'b' & 'c'

Description : In case of brasses, with decreasing zinc percentage and increasing copper percentage, its __________ increases. (A) Percentage elongation (B) Brinell hardness (C) Tensile strength (D) All 'a', 'b' & 'c'

Last Answer : (A) Percentage elongation

The property by virtue of which metals can be beaten into thin sheets is known as: A. Density B. Malleability C. Conductivity D. Ductility

Description : The property by virtue of which metals can be beaten into thin sheets is known as: A. Density B. Malleability C. Conductivity D. Ductility

Last Answer : ANSWER: B

Which of the following properties is generally found, in non-metals?' (1) Brittleness (2) Conductivity (3) Ductility (4) Malleability

Description : Which of the following properties is generally found, in non-metals?' (1) Brittleness (2) Conductivity (3) Ductility (4) Malleability

Last Answer : (1) Brittleness Explanation: An important physical property of non metals is that they are brittle and hence cannot be beaten into sheets or drawn into wires. In other words, non-metals are non-malleable and non-ductile. Where stress is applied on nonmetals, they shatter into pieces.

Presence of 0.3 to 0.5% arsenic in copper increases its (A) Ductility (B) Malleability (C) Tenacity & hardness (D) Electrical conductivity

Description : Presence of 0.3 to 0.5% arsenic in copper increases its (A) Ductility (B) Malleability (C) Tenacity & hardness (D) Electrical conductivity

Last Answer : (C) Tenacity & hardness

A material is able to retain the deformation permanently by virtue of its (A) Elasticity (B) Plasticity (C) Ductility (D) Malleability

Description : A material is able to retain the deformation permanently by virtue of its (A) Elasticity (B) Plasticity (C) Ductility (D) Malleability

Last Answer : (B) Plasticity

Cast iron compared to steel is better in (A) Ductility (B) Fluidity & castability (C) Strength (D) Malleability

Description : Cast iron compared to steel is better in (A) Ductility (B) Fluidity & castability (C) Strength (D) Malleability

Last Answer : (B) Fluidity & castability

The most distinguished property of malleable cast iron is its high (A) Ductility (B) Hardness (C) Malleability (D) None of these

Description : The most distinguished property of malleable cast iron is its high (A) Ductility (B) Hardness (C) Malleability (D) None of these

Last Answer : (A) Ductility

The property by virtue of which metals can be beaten into thin sheets is known as? A. Ductility B. Malleability (Answer)

Description : The property by virtue of which metals can be beaten into thin sheets is known as? A. Ductility B. Malleability (Answer)

Last Answer : B. Malleability (Answer)

The ability of a material to be formed by hammering or rolling is known as _________ a) Malleability b) Ductility c) Harness d) Brittleness

Description : The ability of a material to be formed by hammering or rolling is known as _________ a) Malleability b) Ductility c) Harness d) Brittleness

Last Answer : a) Malleability

The property of metals being beaten into thin sheets is called A) Ductility B) Malleability C)Brittle D)None of these

Description : The property of metals being beaten into thin sheets is called A) Ductility B) Malleability C)Brittle D)None of these

Last Answer : B) Malleability

__________ is the property of a soil to undergo large deformations when stressed, without cracking or crumbling due to the lubricating effect of the water films between adjacent particles. a. Bending b. Malleability c. Ductility d. Plasticity

Description : __________ is the property of a soil to undergo large deformations when stressed, without cracking or crumbling due to the lubricating effect of the water films between adjacent particles. a. Bending b. Malleability c. Ductility d. Plasticity

Last Answer : d. Plasticity

The property by which a body returns to its original shape after removal of the force, is called (A) Plasticity (B) Elasticity (C) Ductility (D) Malleability

Description : The property by which a body returns to its original shape after removal of the force, is called  (A) Plasticity  (B) Elasticity  (C) Ductility  (D) Malleability 

Last Answer : (B) Elasticity 

The property of a material by which it can be beaten or rolled into thin plates, is called (A) Malleability (B) Ductility (C) Plasticity (D) Elasticity

Description : The property of a material by which it can be beaten or rolled into thin plates, is called  (A) Malleability  (B) Ductility  (C) Plasticity  (D) Elasticity

Last Answer : (A) Malleability 

The property of a material by which it can be drawn to a smaller section, due to tension, is called (A) Plasticity (B) Ductility (C) Elasticity (D) Malleability

Description : The property of a material by which it can be drawn to a smaller section, due to tension, is called (A) Plasticity (B) Ductility (C) Elasticity (D) Malleability

Last Answer : (B) Ductility

Silver is used for high precision electrical contacts in computer due to its property of ______. a) malleability b)conductivity c)ductility d)none

Description : Silver is used for high precision electrical contacts in computer due to its property of ______. a) malleability b)conductivity c)ductility d)none

Last Answer : b)conductivity

Property of material which allows it to be drawn out into wires is (A) Ductility. (B) Solder ability. (C) Super conductivity. (D) Malleability.

Description : Property of material which allows it to be drawn out into wires is (A) Ductility. (B) Solder ability. (C) Super conductivity. (D) Malleability.

Last Answer : (A) Ductility.

Write on ductility and malleability of material.

Description : Write on ductility and malleability of material. 

Last Answer : Ductility Ductility is the ability of a material to deform plastically without fracture under tensile load. Because of this property , materials can be drawn out into fine wire without fracture ... Gold and silver are highly malleable. Malleable metals usually bend and twist in various shapes.

Which of the following properties is generally found in nonmetals? (1) Brittleness (2) Conductivity (3) Ductility (4) Malleability

Description : Which of the following properties is generally found in nonmetals? (1) Brittleness (2) Conductivity (3) Ductility (4) Malleability

Last Answer : Brittleness

Spiral spring is quite rigid. (a) Yes (b) No it is flexible (c) It is of moderate rigidity (d) Rigidity can’t be determined

Description : Spiral spring is quite rigid. (a) Yes (b) No it is flexible (c) It is of moderate rigidity (d) Rigidity can’t be determined

Last Answer : (b) No it is flexible

The load required to produce a unit deflection in the spring is called (a) Modulus of Rigidity (b) Spring stiffness (c) Flexural rigidity (d) Tensional rigidity

Description : The load required to produce a unit deflection in the spring is called (a) Modulus of Rigidity (b) Spring stiffness (c) Flexural rigidity (d) Tensional rigidity

Last Answer : b) Spring stiffness

Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4

Description : Find total number coils in a spring having square and ground ends. Deflection in the spring is 6mm when load of 1100N is applied. Modulus of rigidity is 81370N/mm². Wire diameter and pitch circle diameter are 10mm and 50mm respectively. a) 7 b) 6 c) 5 d) 4

Last Answer : a) 7

Determine number of coils in a helical compression spring, if modulus of rigidity is 80 Gpa and spring stiffness is 50 N/ mm. Assume wire diameter and spring index as 8 mm and 5 respectively a. 11.8 turns b. 12.8 turns c. 13.3 turns d. None of the above

Description : Determine number of coils in a helical compression spring, if modulus of rigidity is 80 Gpa and spring stiffness is 50 N/ mm. Assume wire diameter and spring index as 8 mm and 5 respectively a. 11.8 turns b. 12.8 turns c. 13.3 turns d. None of the above

Last Answer : b. 12.8 turns

The load required to produce a unit deflection in the spring is called (a) Modulus of Rigidity (b) Spring stiffness (c) Flexural rigidity (d) Tensional rigidity

Description : The load required to produce a unit deflection in the spring is called (a) Modulus of Rigidity (b) Spring stiffness (c) Flexural rigidity (d) Tensional rigidity

Last Answer : (b) Spring stiffness

In the theorem of three moments in the most general form a.two flexural rigidity are considered b. only one flexural rigidity is considered c.no flexural rigidity is considered d.flexural rigidity is doubled

Description : In the theorem of three moments in the most general form a.two flexural rigidity are considered b. only one flexural rigidity is considered c.no flexural rigidity is considered d.flexural rigidity is doubled

Last Answer : a.two flexural rigidity are considered

A simply supported beam carries uniformly distributed load of 20 kN/m over the length of 5 m. If flexural rigidity is 30000 kN.m2, what is the maximum deflection in the beam? a. 5.4 mm b. 1.08 mm c. 6.2 mm d. 8.6 mm

Description : A simply supported beam carries uniformly distributed load of 20 kN/m over the length of 5 m. If flexural rigidity is 30000 kN.m2, what is the maximum deflection in the beam? a. 5.4 mm b. 1.08 mm c. 6.2 mm d. 8.6 mm

Last Answer : a. 5.4 mm

The shafts will have same strength on the basis of torsional rigidity, if (a) diameter and length of both shafts is same (b) material of both shafts is same (c) angle of twist for both shafts is same (d) all of above conditions are satisfied

Description : The shafts will have same strength on the basis of torsional rigidity, if (a) diameter and length of both shafts is same (b) material of both shafts is same (c) angle of twist for both shafts is same (d) all of above conditions are satisfied

Last Answer : (d) all of above conditions are satisfied

Flexible shafts have ______ rigidity in bending moment. a) High b) Low c) Very high d) Extremely low

Description : Flexible shafts have ______ rigidity in bending moment. a) High b) Low c) Very high d) Extremely low

Last Answer : b) Low

Flexible shafts have ___ rigidity in torsion making them flexible. a) Low b) High c) Very high d) Infinitely small

Description : Flexible shafts have ___ rigidity in torsion making them flexible. a) Low b) High c) Very high d) Infinitely small

Last Answer : b) High