What is a good device to use for obtaining viscosity data for a non-Newtonian fluid?

What is a good device to use for obtaining viscosity data for a non-Newtonian fluid?
by

1 Answer

Answer :

Consider a rotational viscometer. It will measure the shear rate applied and the subsequent viscosity at  the same time. You can also vary the temperature and time the stresses are applied for the truly “fun”  non-Newtonian fluids. According to Cole-Parmer, “The rotational viscometer measures viscosity by  determining the viscous resistance of the fluid. This measurement is obtained by immersing a spindle  into the test fluid. The viscometer measures the additional torque required for the spindle to overcome  viscous resistance and regain constant speed. This value is then converted to centipoises and displayed  on the instrument’s LCD readout.” When testing a tomato sauce sample, the following results were  observed: “A sample of tomato sauce was analyzed to determine the product’s viscosity profile. The test  was conducted at a temperature of 25°C. An up/down speed ramp was performed from 10 to 100 RPM,  giving a viscosity range of from 3,800 to 632.5 cP, over shear rates from 3.4 to 34.0 reciprocal seconds.  The test data obtained for tomato sauce shows that this product exhibits a marked shear thinning  viscosity profile over the test conditions.
by

Related questions

A fluid whose apparent viscosity increases with shear rate is termed as the __________ fluid. (A) Newtonian (B) Viscous (C) Dilatant (D) Non-viscous

Description : A fluid whose apparent viscosity increases with shear rate is termed as the __________ fluid. (A) Newtonian (B) Viscous (C) Dilatant (D) Non-viscous

Last Answer : (C) Dilatan

Pick out the wrong statement. (A) Momentum transfer in laminar flow results from velocity gradient (B) A fluid in equilibrium is not free from shear stress (C) The viscosity of a non-Newtonian fluid is a function of temperature only (D) Both (B) and (C)

Description : Pick out the wrong statement. (A) Momentum transfer in laminar flow results from velocity gradient (B) A fluid in equilibrium is not free from shear stress (C) The viscosity of a non-Newtonian fluid is a function of temperature only (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

A fluid whose viscosity does not change with the rate of deformation or shear strain is known as (A) Real fluid (B) Ideal fluid (C) Newtonian fluid (D) Non-Newtonian fluid

Description : A fluid whose viscosity does not change with the rate of deformation or shear strain is known as (A) Real fluid (B) Ideal fluid (C) Newtonian fluid (D) Non-Newtonian fluid

Last Answer : Answer: Option C

A fluid having no viscosity is known as (A) Real fluid (B) Ideal fluid (C) Newtonian fluid (D) Non-Newtonian fluid

Description : A fluid having no viscosity is known as (A) Real fluid (B) Ideal fluid (C) Newtonian fluid (D) Non-Newtonian fluid

Last Answer : Answer: Option B

A fluid which obeys the Newton's law of viscosity is termed as(A) Real fluid (B) Ideal fluid (C) Newtonian fluid (D) Non-Newtonian fluid

Description : A fluid which obeys the Newton's law of viscosity is termed as (A) Real fluid (B) Ideal fluid (C) Newtonian fluid (D) Non-Newtonian fluid

Last Answer : Answer: Option C

Power required for mixing Newtonian fluids is a function of the (A) Speed of impeller, diameter of impeller & viscosity (B) Density & viscosity of fluid only (C) Density of fluid, viscosity of fluid & impeller dia only (D) None of these

Description : Power required for mixing Newtonian fluids is a function of the (A) Speed of impeller, diameter of impeller & viscosity (B) Density & viscosity of fluid only (C) Density of fluid, viscosity of fluid & impeller dia only (D) None of these

Last Answer : (D) None of these

For laminar flow of Newtonian fluids through a circular pipe, for a given pressure drop and length & diameter of pipe, the velocity of fluid is proportional to (where, μ = fluid viscosity ) (A) μ (B) 1/μ (C) √μ (D) 1/√μ

Description : For laminar flow of Newtonian fluids through a circular pipe, for a given pressure drop and length & diameter of pipe, the velocity of fluid is proportional to (where, μ = fluid viscosity ) (A) μ (B) 1/μ (C) √μ (D) 1/√μ

Last Answer : (B) 1/μ

. A fluid which has a linear relationship between the magnitude of applied shear-stress and the resulting rate of deformation is called a/an __________ fluid. (A) Newtonian (B) Non-Newtonian (C) Ideal (D) Incompressible

Description : . A fluid which has a linear relationship between the magnitude of applied shear-stress and the resulting rate of deformation is called a/an __________ fluid. (A) Newtonian (B) Non-Newtonian (C) Ideal (D) Incompressible

Last Answer : (A) Newtonian

Sewage sludge is __________ type of non-Newtonian fluid. (A) Dilatant (B) Bingham plastic (C) Pseudo plastic (D) None of these

Description : Sewage sludge is __________ type of non-Newtonian fluid. (A) Dilatant (B) Bingham plastic (C) Pseudo plastic (D) None of these

Last Answer : (B) Bingham plastic

Non-colloidal solution is an example of the __________ fluid. (A) Non-Newtonian (B) Newtonian (C) Dilatent (D) Pseudo-plastic

Description : Non-colloidal solution is an example of the __________ fluid. (A) Non-Newtonian (B) Newtonian (C) Dilatent (D) Pseudo-plastic

Last Answer : (B) Newtonian

Pick out the correct statement. (A) Human blood is a Newtonian fluid (B) A Newtonian fluid obeys Newton's law of cooling (C) For a non-Newtonian fluid, a straight line passes through the origin in a plot between shear stress and shear gradien

Description : Pick out the correct statement. (A) Human blood is a Newtonian fluid (B) A Newtonian fluid obeys Newton's law of cooling (C) For a non-Newtonian fluid, a straight line passes through the origin in a plot between shear stress and shear gradien

Last Answer : (B) A Newtonian fluid obeys Newton's law of cooling

The fluid velocity varies as the square of the cylindrical pipe diameter, in case of steady state laminar flow at constant pressure drop, for __________ fluid. (A) Newtonian (B) Dilatant (C) Pseudo-plastic (D) Non-Newtonian

Description : The fluid velocity varies as the square of the cylindrical pipe diameter, in case of steady state laminar flow at constant pressure drop, for __________ fluid. (A) Newtonian (B) Dilatant (C) Pseudo-plastic (D) Non-Newtonian

Last Answer : (A) Newtonian

Which of the following is a Newtonian fluid? (A) Rubber latex (B) Sewage sludge (C) Quicksand (D) Non-colloidal solution

Description : Which of the following is a Newtonian fluid? (A) Rubber latex (B) Sewage sludge (C) Quicksand (D) Non-colloidal solution

Last Answer : (D) Non-colloidal solution

For a given fluid, as the pipe diameter increases, the pumping cost (A) Decreases (B) Increases (C) Remains the same (D) May increase or decrease, depending upon whether the fluid is Newtonian or non-Newtonian

Description : For a given fluid, as the pipe diameter increases, the pumping cost (A) Decreases (B) Increases (C) Remains the same (D) May increase or decrease, depending upon whether the fluid is Newtonian or non-Newtonian

Last Answer : (A) Decreases

16. The shear stress-strain graph for a Non-Newtonian fluid is a curve. A) Correct B) Incorrect

Description : 16. The shear stress-strain graph for a Non-Newtonian fluid is a curve. A) Correct B) Incorrect

Last Answer : A

Water is a __________ fluid. (A) Real (B) Ideal (C) Newtonian (D) Non-Newtonian

Description : Water is a __________ fluid. (A) Real (B) Ideal (C) Newtonian (D) Non-Newtonian

Last Answer : Answer: Option C

Rubber latex is an example of a __________ fluid. (A) Pseudo plastic (B) Bingham plastic (C) Dilatent (D) Newtonian

Description : Rubber latex is an example of a __________ fluid. (A) Pseudo plastic (B) Bingham plastic (C) Dilatent (D) Newtonian

Last Answer : (A) Pseudo plastic

The ratio of average fluid velocity to the maximum velocity in case of laminar flow of a Newtonian fluid in a circular pipe is (A) 0.5 (B) 1 (C) 2 (D) 0.66

Description : The ratio of average fluid velocity to the maximum velocity in case of laminar flow of a Newtonian fluid in a circular pipe is (A) 0.5 (B) 1 (C) 2 (D) 0.66

Last Answer : (A) 0.5

Sewage sludge is an example of the __________ fluid. (A) Bingham plastic (B) Newtonian (C) Pseudo plastic (D) Dilatent

Description : Sewage sludge is an example of the __________ fluid. (A) Bingham plastic (B) Newtonian (C) Pseudo plastic (D) Dilatent

Last Answer : (A) Bingham plastic

Pick out the wrong statement pertaining to fluid flow. (A) The ratio of average velocity to the maximum velocity for turbulent flow of Newtonian fluid in circular pipes is 0.5 (B) The Newtonian fluid velocity in a circular pipe flow is maximum at the centre of the pipe (C) Navier-Stokes equation is applicable to the analysis of viscous flows

Description : Pick out the wrong statement pertaining to fluid flow. (A) The ratio of average velocity to the maximum velocity for turbulent flow of Newtonian fluid in circular pipes is 0.5 (B) The Newtonian ... at the centre of the pipe (C) Navier-Stokes equation is applicable to the analysis of viscous flows

Last Answer : (A) The ratio of average velocity to the maximum velocity for turbulent flow of Newtonian fluid in circular pipes is 0.5

Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. (du/dy) n the value of 'n' for pseudoplastic and Dilatant fluid are < 1 and >1 respectively (C) Shear stress for Newtonian fluid is proportional to the rate of shear in the direction perpendicular to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Description : Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. ... to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Last Answer : (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

The fluid in which the shearing stress within it is proportional to the velocity gradient across the sheared section, is called a __________ fluid. (A) Bingham (B) Newtonian (C) Perfect (D) None of these

Description : The fluid in which the shearing stress within it is proportional to the velocity gradient across the sheared section, is called a __________ fluid. (A) Bingham (B) Newtonian (C) Perfect (D) None of these

Last Answer : (B) Newtonian

Laminar flow of a Newtonian fluid ceases to exist, when the Reynolds number exceeds (A) 4000 (B) 2100 (C) 1500 (D) 3000

Description : Laminar flow of a Newtonian fluid ceases to exist, when the Reynolds number exceeds (A) 4000 (B) 2100 (C) 1500 (D) 3000

Last Answer : (B) 2100

In power law, ζ = [A (du/dy) 2 + B] then the fluid is (A) Newtonian (B) Dilatant (C) Thixotropic (D) Rheopectic

Description : In power law, ζ = [A (du/dy) 2 + B] then the fluid is (A) Newtonian (B) Dilatant (C) Thixotropic (D) Rheopectic

Last Answer : (A) Newtonian

Rubber latex is an example of __________ fluid. (A) Dilatants (B) Newtonian (C) Pseudo plastic (D) Bingham plastic

Description : Rubber latex is an example of __________ fluid. (A) Dilatants (B) Newtonian (C) Pseudo plastic (D) Bingham plastic

Last Answer : (C) Pseudo plastic

A Newtonian fluid is that (A) Which follows Newton's law of motion (B) Which needs a minimum shear, before it starts deforming (C) For which shear & deformation are related as T = µ (∂u/∂y) (D) None of these

Description : A Newtonian fluid is that (A) Which follows Newton's law of motion (B) Which needs a minimum shear, before it starts deforming (C) For which shear & deformation are related as T = µ (∂u/∂y) (D) None of these

Last Answer : (C) For which shear & deformation are related as T = µ (∂u/∂y)

In case of turbulent flow of a Newtonian fluid in a straight pipe, the maximum velocity is equal to (where, Vavg = average fluid velocity) (A) Vavg (B) 1.2 Vavg (C) 1.5 Vavg (D) 1.8 Vavg

Description : In case of turbulent flow of a Newtonian fluid in a straight pipe, the maximum velocity is equal to (where, Vavg = average fluid velocity) (A) Vavg (B) 1.2 Vavg (C) 1.5 Vavg (D) 1.8 Vavg

Last Answer : (B) 1.2 Vavg

The fluid velocity varies as the cube of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop for __________ fluid. (A) Newtonian (B) Pseudo-plastic (C) Dilatent (D) Bingham plastic

Description : The fluid velocity varies as the cube of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop for __________ fluid. (A) Newtonian (B) Pseudo-plastic (C) Dilatent (D) Bingham plastic

Last Answer : (B) Pseudo-plastic

Quicksand is an example of a __________ fluid. (A) Bingham plastic (B) Dilatant (C) Newtonian (D) Pseudo plastic

Description : Quicksand is an example of a __________ fluid. (A) Bingham plastic (B) Dilatant (C) Newtonian (D) Pseudo plastic

Last Answer : (B) Dilatant

Paper pulp is an example of __________ fluid.(A) Dilatant (B) Bingham plastic (C) Newtonian (D) Pseudo-plastic

Description : Paper pulp is an example of __________ fluid. (A) Dilatant (B) Bingham plastic (C) Newtonian (D) Pseudo-plastic

Last Answer : (B) Bingham plastic

An ideal plastic substance indicates no deformation, when stressed upto yield stress, but behaves like a Newtonian fluid beyond yield stress. Which of the following is an ideal plastic? (A) Sewage sludge (B) Rubber latex (C) Blood (D) Sugar solution

Description : An ideal plastic substance indicates no deformation, when stressed upto yield stress, but behaves like a Newtonian fluid beyond yield stress. Which of the following is an ideal plastic? (A) Sewage sludge (B) Rubber latex (C) Blood (D) Sugar solution

Last Answer : (A) Sewage sludge

For turbulent flow of Newtonian fluid in a circular cross-section pipe, the ratio of maximum to average fluid velocity is (A) 0.5 (B) 1 (C) 0.66 (D) < 0.5

Description : For turbulent flow of Newtonian fluid in a circular cross-section pipe, the ratio of maximum to average fluid velocity is (A) 0.5 (B) 1 (C) 0.66 (D) < 0.5

Last Answer : (B) 1

For laminar flow of Newtonian fluid in a circular pipe, the velocitydistribution is a function of the distance 'd' measured from the centre line ofthe pipe, and it follows a __________ relationship.(A) Logarithmic(B) Parabolic(C) Hyperbolic(D) Linear

Description : For laminar flow of Newtonian fluid in a circular pipe, the velocitydistribution is a function of the distance 'd' measured from the centre line of the pipe, and it follows a __________ relationship. (A) Logarithmic (B) Parabolic (C) Hyperbolic (D) Linear

Last Answer : (B) Parabolic

The fluid velocity varies as the square root of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop of __________ fluid. (A) Dilatent (B) Pseudo-plastic (C) Bingham plastic (D) Newtonian

Description : The fluid velocity varies as the square root of the cylindrical pipe diameter in case of steady state laminar flow at constant pressure drop of __________ fluid. (A) Dilatent (B) Pseudo-plastic (C) Bingham plastic (D) Newtonian

Last Answer : (A) Dilatent

A fluid is termed as the Newtonian fluid, when the shear stress is __________ the velocity gradient. (A) Independent of (B) Inversely proportional to (C) Directly proportional to (D) None of these

Description : A fluid is termed as the Newtonian fluid, when the shear stress is __________ the velocity gradient. (A) Independent of (B) Inversely proportional to (C) Directly proportional to (D) None of these

Last Answer : (C) Directly proportional to

The stress-strain relation of the Newtonian fluid is (A) Linear (B) Parabolic (C) Hyperbolic (D) Inverse type

Description : The stress-strain relation of the Newtonian fluid is (A) Linear (B) Parabolic (C) Hyperbolic (D) Inverse type

Last Answer : Answer: Option A

The shear stress-strain graph for a Newtonian fluid is a (A) Straight line (B) Parabolic curve (C) Hyperbolic curve (D) Elliptical

Description : The shear stress-strain graph for a Newtonian fluid is a (A) Straight line (B) Parabolic curve (C) Hyperbolic curve (D) Elliptical

Last Answer : Answer: Option A

What Is A Newtonian Fluid?

Description : What Is A Newtonian Fluid?

Last Answer : A Newtonian fluid possesses a linear stress strain relationship curve and it passes through the origin. The fluid properties of a Newtonian fluid do not change when any force acts upon it.

Two fluids are flowing through two similar pipes of the same diameter. The Reynold's number is same. For the same flow rate if the viscosity of a fluid is reduced to half the value of the first fluid, the pressure drop will (A) Increase (B) Decrease (C) Remain unchanged (D) Data insufficient to predict relative pressure drop

Description : Two fluids are flowing through two similar pipes of the same diameter. The Reynold's number is same. For the same flow rate if the viscosity of a fluid is reduced to half the value of the ... (A) Increase (B) Decrease (C) Remain unchanged (D) Data insufficient to predict relative pressure drop

Last Answer : (B) Decrease

The diffusivity, DAB (for component A diffusing in B) is equal to the diffusivity DBA (for component B diffusing in A) for a binary mixture of (A) Newtonian liquids (B) Non-Newtonian liquids (C) Ideal gases (D) Real gases

Description : The diffusivity, DAB (for component A diffusing in B) is equal to the diffusivity DBA (for component B diffusing in A) for a binary mixture of (A) Newtonian liquids (B) Non-Newtonian liquids (C) Ideal gases (D) Real gases

Last Answer : (C) Ideal gases

Diaphragm valves are used for handling __________ fluids. (A) Corrosive (B) Viscous (C) Non-Newtonian (D) Solid suspended

Description : Diaphragm valves are used for handling __________ fluids. (A) Corrosive (B) Viscous (C) Non-Newtonian (D) Solid suspended

Last Answer : (A) Corrosive

Shell side pressure drop in a shell and tube heat exchanger does not depend upon the (A) Baffle spacing & shell diameter (B) Tube diameter & pitch (C) Viscosity, density & mass velocity of shell side fluid (D) None of these

Description : Shell side pressure drop in a shell and tube heat exchanger does not depend upon the (A) Baffle spacing & shell diameter (B) Tube diameter & pitch (C) Viscosity, density & mass velocity of shell side fluid (D) None of these

Last Answer : (D) None of these

Which characteristic of a fluid is not important in deciding its route in a shell and tube heat exchanger? (A) Corrosiveness (B) Fouling characteristic (C) Viscosity (D) None of these

Description : Which characteristic of a fluid is not important in deciding its route in a shell and tube heat exchanger? (A) Corrosiveness (B) Fouling characteristic (C) Viscosity (D) None of these

Last Answer : (D) None of these

Which of the following parameters of the fluid is not very important, while deciding its route in a shell and tube heat exchanger? (A) Corrosiveness & fouling characteristics (B) Pressure (C) Viscosity (D) Density

Description : Which of the following parameters of the fluid is not very important, while deciding its route in a shell and tube heat exchanger? (A) Corrosiveness & fouling characteristics (B) Pressure (C) Viscosity (D) Density

Last Answer : (D) Density

Pressure gradient in the pipe flow is influenced by the (A) Diameter of pipe (B) Velocity of the fluid (C) Density & viscosity of the fluid (D) All (A), (B) and (C)

Description : Pressure gradient in the pipe flow is influenced by the (A) Diameter of pipe (B) Velocity of the fluid (C) Density & viscosity of the fluid (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In case of a pipe of constant cross-sectional area, the maximum fluid velocity obtainable is (A) The velocity of sound (B) Dependent on its cross-sectional area (C) Dependent on fluid viscosity (D) Dependent on fluid density

Description : In case of a pipe of constant cross-sectional area, the maximum fluid velocity obtainable is (A) The velocity of sound (B) Dependent on its cross-sectional area (C) Dependent on fluid viscosity (D) Dependent on fluid density

Last Answer : (A) The velocity of sound

Minimum fluidisation velocity for a specific system depends upon the (A) Particle size (B) Fluid viscosity (C) Density of both the particle & the fluid (D) All (A), (B) and (C)

Description : Minimum fluidisation velocity for a specific system depends upon the (A) Particle size (B) Fluid viscosity (C) Density of both the particle & the fluid (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

While starting a centrifugal pump, its delivery valve should be kept (A) Opened (B) Closed (C) Either opened or closed; it does not make any difference (D) Either opened or closed; depending on the fluid viscosity

Description : While starting a centrifugal pump, its delivery valve should be kept (A) Opened (B) Closed (C) Either opened or closed; it does not make any difference (D) Either opened or closed; depending on the fluid viscosity

Last Answer : (B) Closed

The continuity equation (A) Is independent of the compressibility of the fluid (B) Is dependent upon the viscosity of the fluid (C) Represents the conservation of mass (D) None of these

Description : The continuity equation (A) Is independent of the compressibility of the fluid (B) Is dependent upon the viscosity of the fluid (C) Represents the conservation of mass (D) None of these

Last Answer : (C) Represents the conservation of mass