When using a pumping loop to mix two miscible fluids in a tank, when can the content are considered well mixed?

When using a pumping loop to mix two miscible fluids in a tank, when can the content are  considered well mixed?
by

1 Answer

Answer :

A rule of thumb is to turn the tank over three (3) times and then sample the tank for mixture  properties. By “turn the tank over”, we mean to force the entire volume of the tank through the pump  at least three times. More turnovers may be necessary, but three times is a good starting point.
by

Related questions

A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Description : A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Last Answer : (A) Employs such an impeller, through which the flow is a combination of radial & axial flow

Equal volumes of aniline and diesel oil when mixed at room temperature (during summer) was found to be completely miscible. It means that the aniline point of the diesel is __________ the room temperature. (A) More than (B) Less than (C) Same as (D) Either more or less; depends on the room temperature

Description : Equal volumes of aniline and diesel oil when mixed at room temperature (during summer) was found to be completely miscible. It means that the aniline point of the diesel is __________ the room temperature. (A) ... (B) Less than (C) Same as (D) Either more or less; depends on the room temperature

Last Answer : (C) Same as

To manage mixed weed flora in barley which of the herbicides is to be applied a).2,4-D b). Isoproturon c). a and b as tank mix d). None of these

Description : To manage mixed weed flora in barley which of the herbicides is to be applied a).2,4-D b). Isoproturon c). a and b as tank mix d). None of these

Last Answer : c). a and b as tank mix

LMTD for evaporators & condensers for a given terminal parameters & set of conditions for counter-flow is equal to that for parallel flow. In such heat exchangers, with one of the fluids condensing or evaporating, the surface area required is the least in the __________ flow. (A) Parallel (B) Mixed (C) Counter flow (D) Same in either 'a', b' or 'c'

Description : LMTD for evaporators & condensers for a given terminal parameters & set of conditions for counter-flow is equal to that for parallel flow. In such heat exchangers, with one of the fluids condensing or evaporating, the surface ... Parallel (B) Mixed (C) Counter flow (D) Same in either 'a', b' or 'c'

Last Answer : (D) Same in either 'a', b' or 'c'

How much would it cost to get septic tank pumping?

Description : How much would it cost to get septic tank pumping?

Last Answer : You cannot say for sure, it all depends on where you live, but generally, the cost to have your septic tank pumped is around $70 to $200 dollars to have your septic tank pumped by professionals.

When gravity and pumping systems of water distribution are adopted, the type of distribution reservoir, is (A) Elevated tank (B) Ground source reservoir (C) Intz tank (D) Stand pipe

Description : When gravity and pumping systems of water distribution are adopted, the type of distribution  reservoir, is  (A) Elevated tank  (B) Ground source reservoir  (C) Intz tank  (D) Stand pipe

Last Answer : (A) Elevated tank 

Corrosion of well pipes may not be reduced by (A) Reducing the draw down and the pumping rate (B) Reducing the flow velocity (C) Using thicker pipes (D) Using screens having larger area of openings

Description : Corrosion of well pipes may not be reduced by  (A) Reducing the draw down and the pumping rate  (B) Reducing the flow velocity  (C) Using thicker pipes  (D) Using screens having larger area of openings 

Last Answer : (D) Using screens having larger area of openings 

Which one of the following is NOT part of the streak-plate method? a. Making four sets of streaks on a plate. b. Diluting a mixed culture in molten agar. c. Using a mixed culture. d. Using a sterilized loop.

Description : Which one of the following is NOT part of the streak-plate method? a. Making four sets of streaks on a plate. b. Diluting a mixed culture in molten agar. c. Using a mixed culture. d. Using a sterilized loop.

Last Answer : b. Diluting a mixed culture in molten agar.

Which of the following is used for pumping crude oil from oil well? (A) Single stage centrifugal pump (B) Gear pump (C) Screw pump (D) Duplex/triplex reciprocating pump

Description : Which of the following is used for pumping crude oil from oil well? (A) Single stage centrifugal pump (B) Gear pump (C) Screw pump (D) Duplex/triplex reciprocating pump

Last Answer : (D) Duplex/triplex reciprocating pump

A gravity decanter is meant for the separation of two __________ density. (A) Immiscible liquids of different (B) Miscible liquids of different (C) Immiscible liquids of same (D) Miscible liquids of same

Description : A gravity decanter is meant for the separation of two __________ density. (A) Immiscible liquids of different (B) Miscible liquids of different (C) Immiscible liquids of same (D) Miscible liquids of same

Last Answer : (A) Immiscible liquids of different

A plait point is the point on the solubility curve, where the tie line reduces to a point. What is the number of plait point for a ternary system containing two pairs of partially miscible liquids? (A) 0 (B) 1 (C) 2 (D) 3

Description : A plait point is the point on the solubility curve, where the tie line reduces to a point. What is the number of plait point for a ternary system containing two pairs of partially miscible liquids? (A) 0 (B) 1 (C) 2 (D) 3

Last Answer : (A) 0

Critical solution temperature (or the con-solute temperature) for partially miscible liquids (e.g., phenol-water) is the minimum temperature at which (A) A homogeneous solution (say of phenol water) is formed (B) Mutual solubility of the two liquids shows a decreasing trend (C) Two liquids are completely separated into two layers (D) None of these

Description : Critical solution temperature (or the con-solute temperature) for partially miscible liquids (e.g., phenol-water) is the minimum temperature at which (A) A homogeneous solution (say of phenol water) is ... a decreasing trend (C) Two liquids are completely separated into two layers (D) None of these

Last Answer : (A) A homogeneous solution (say of phenol water) is formed

What is the number of degree of freedom for a system of two miscible non-reacting species in vapor-liquid equilibrium forming an azeotrope? (A) 0 (B) 2 (C) 1 (D) 3

Description : What is the number of degree of freedom for a system of two miscible non-reacting species in vapor-liquid equilibrium forming an azeotrope? (A) 0 (B) 2 (C) 1 (D) 3

Last Answer : (C) 1

What is the degree of freedom for two miscible (non-reacting) substances in vapor-liquid equilibrium forming an azeotrope? (A) 0 (B) 1 (C) 2 (D) 3

Description : What is the degree of freedom for two miscible (non-reacting) substances in vapor-liquid equilibrium forming an azeotrope? (A) 0 (B) 1 (C) 2 (D) 3

Last Answer : (C) 2

Fugacity is a measure of the (A) Escaping tendencies of the same substance in different phases of a system (B) Relative volatility of a mixture of two miscible liquids (C) Behaviour of ideal gases (D) None of these

Description : Fugacity is a measure of the (A) Escaping tendencies of the same substance in different phases of a system (B) Relative volatility of a mixture of two miscible liquids (C) Behaviour of ideal gases (D) None of these

Last Answer : (A) Escaping tendencies of the same substance in different phases of a system

A solute distributes itself between two non-miscible solvents in contact with each other in such a way that, at a constant temperature, the ratio of its concentrations in two layers is constant, irrespective of its total amount". This is (A) The distribution law (B) Followed from Margules equation (C) A corollary of Henry's law (D) None of these

Description : A solute distributes itself between two non-miscible solvents in contact with each other in such a way that, at a constant temperature, the ratio of its concentrations in two layers is constant, irrespective of ... B) Followed from Margules equation (C) A corollary of Henry's law (D) None of these

Last Answer : (A) The distribution law

Aniline point is the temperature at which (A) Equal weight of diesel & the aniline are completely miscible (B) Equal weight of aniline & the test sample are completely miscible (C) Equal volume of aniline & the test sample are completely miscible (D) Aniline vaporises

Description : Aniline point is the temperature at which (A) Equal weight of diesel & the aniline are completely miscible (B) Equal weight of aniline & the test sample are completely miscible (C) Equal volume of aniline & the test sample are completely miscible (D) Aniline vaporises

Last Answer : (C) Equal volume of aniline & the test sample are completely miscible

Ribbon blenders are exclusively meant for (A) Blending miscible liquids (B) Non-flowing powder and thin pastes (C) Bath mixing (D) Continuous mixing

Description : Ribbon blenders are exclusively meant for (A) Blending miscible liquids (B) Non-flowing powder and thin pastes (C) Bath mixing (D) Continuous mixing

Last Answer : (B) Non-flowing powder and thin pastes

Sides of equilateral-triangular co-ordinates (on which ternary liquid system is plotted) represent (A) A pure component (B) A binary mixture (C) A ternary mixture (D) Partially miscible ternary system

Description : Sides of equilateral-triangular co-ordinates (on which ternary liquid system is plotted) represent (A) A pure component (B) A binary mixture (C) A ternary mixture (D) Partially miscible ternary system

Last Answer : (B) A binary mixture

Steam distillation is not recommended to be used, if the (A) Azeotropic mixture is to be separated and the final product is miscible with water (B) Liquids decompose, if distilled directly at atmospheric pressure (C) Material cannot be distilled by indirect heating even under low pressure, because of the high boiling temperature (D) Material to be distilled is thermally unstable or has the tendency to react with other components associated with it, at the boiling temperature

Description : Steam distillation is not recommended to be used, if the (A) Azeotropic mixture is to be separated and the final product is miscible with water (B) Liquids decompose, if ... unstable or has the tendency to react with other components associated with it, at the boiling temperature

Last Answer : (A) Azeotropic mixture is to be separated and the final product is miscible with water

In the diving apparatus, helium is used along with oxygen, because it is (A) Easily available (B) Not soluble in blood at high pressure (C) Lighter than nitrogen (D) Completely miscible with oxygen

Description : In the diving apparatus, helium is used along with oxygen, because it is (A) Easily available (B) Not soluble in blood at high pressure (C) Lighter than nitrogen (D) Completely miscible with oxygen

Last Answer : (B) Not soluble in blood at high pressure

A back mix reactor is (A) Suitable for gas phase reactions (B) Ideal at very low conversion (C) Same as plug flow reactor (PFR) (D) Same as ideal stirred tank reactor

Description : A back mix reactor is (A) Suitable for gas phase reactions (B) Ideal at very low conversion (C) Same as plug flow reactor (PFR) (D) Same as ideal stirred tank reactor

Last Answer : (D) Same as ideal stirred tank reactor

The difference between static water level and pumping water level is known as: a drawdown b well yield c specific capacity d all are correct

Description : The difference between static water level and pumping water level is known as: a drawdown b well yield c specific capacity d all are correct

Last Answer : a drawdown

S1 and S2 are the draw downs in an observation well at times t1 and t2 after pumping. For discharge Q and coefficient of transmissibility T, the relationship, is (A) S2 - S1 = (2.3Q/ ) log10 (t2/t1) (B) S2 - S1 = (2.3Q/4 ) log10 (t2/t1) (C) S2 - S1 = (2.3Q/4 ) loge (t2/t1) (D) S2 - S1 = (2.3Q/4 ) loge (t1/t2

Description : S1 and S2 are the draw downs in an observation well at times t1 and t2 after pumping. For  discharge Q and coefficient of transmissibility T, the relationship, is  (A) S2 - S1 = (2.3Q/ ) log10 (t2/t1)  (B) S2 - S1 ... - S1 = (2.3Q/4 ) loge (t2/t1)  (D) S2 - S1 = (2.3Q/4 ) loge (t1/t2

Last Answer : (B) S2 - S1 = (2.3Q/4 ) log10 (t2/t1) 

The water level in an open well was depressed by pumping 2.5 m and recuperated 2.87 m in 3 hours and 50 minutes. The yield of the well per minute is (A) 0.0033 (B) 0.0044 (C) 0.0055 (D) 0.0066

Description : The water level in an open well was depressed by pumping 2.5 m and recuperated 2.87 m in 3  hours and 50 minutes. The yield of the well per minute is  (A) 0.0033  (B) 0.0044  (C) 0.0055  (D) 0.0066 

Last Answer : (C) 0.0055 

While determining the yield of open wells by the pumping test (A) Velocity of recharging water, increases with depression head (B) Depression head resulting at critical velocity, is called critical depression head (C) Working head is generally limited to (D) Maximum safe yield of an open well, is expected at critical depression head

Description : While determining the yield of open wells by the pumping test  (A) Velocity of recharging water, increases with depression head  (B) Depression head resulting at critical velocity, is called critical ... (D) Maximum safe yield of an open well, is expected at critical depression head 

Last Answer : (D) Maximum safe yield of an open well, is expected at critical depression head 

Pick up the correct statement from the following: (A) The water level in a still well, represents the ground water table level (B) The difference between water table level and the water level in a well after pumping, is called depression head (C) The surface of water table surrounding a well during pumping, forms a cone of depression (D) All the above

Description : Pick up the correct statement from the following:  (A) The water level in a still well, represents the ground water table level  (B) The difference between water table level and the water ... water table surrounding a well during pumping, forms a cone of depression  (D) All the above 

Last Answer : (D) All the above 

A well penetrates to 30 m below the static water table. After 24 hours of pumping at 31.40 litres/minute, the water level in a test well at a distance of 80 m is lowered by 0.5 m and in a well 20 m away water is lowered by 1.0 m. The transmissibility of the aquifer, is (A) 1.185 m2 /minute(B) 1.285 m2/minute (C) 1.385 m2/minute (D) 1.485 m2/minute

Description : A well penetrates to 30 m below the static water table. After 24 hours of pumping at 31.40 litres/minute, the water level in a test well at a distance of 80 m is lowered by 0.5 m and in a well 20 m away water is ... 1.185 m2 /minute (B) 1.285 m2 /minute (C) 1.385 m2 /minute (D) 1.485 m2 /minute

Last Answer : Answer: Option C

When a constant discharge 2.91 litres/sec. was obtained in a pumping test, the draw downs in the test wells at 3 m and 6.184 m were 2.6 m and 0.3 m respectively. If over-all depth of the pumping well was 16 m, the permeability of the soil, is (A) 0.0005 cm/sec (B) 0.001 cm/sec (C) 0.002 cm/sec (D) 0.01 cm/sec

Description : When a constant discharge 2.91 litres/sec. was obtained in a pumping test, the draw downs in the test wells at 3 m and 6.184 m were 2.6 m and 0.3 m respectively. If over-all depth of the pumping well was 16 m, the ... (A) 0.0005 cm/sec (B) 0.001 cm/sec (C) 0.002 cm/sec (D) 0.01 cm/sec

Last Answer : Answer: Option B

Pick out the wrong statement. (A) For a first order consecutive reaction, a tubular flow reactor as compared to a stirred tank reactor provides higher overall selectivity(B) For an ideal mixed reactor at steady state, the exit stream has the samecomposition as fluid within the reactor and the space time is equivalent toholding time for constant density system(C) Plug flow reactor (PFR) is always smaller than mixed reactor for allpositive reaction orders for a particular duty(D) Reaction rate does not decrease appreciably as the reaction proceeds incase of an autocatalytic reaction

Description : Pick out the wrong statement. (A) For a first order consecutive reaction, a tubular flow reactor as compared to a stirred tank reactor provides higher overall selectivity(B) For an ideal ... D) Reaction rate does not decrease appreciably as the reaction proceeds in case of an autocatalytic reaction

Last Answer : (A) For a first order consecutive reaction, a tubular flow reactor as compared to a stirred tank reactor provides higher overall selectivity

Fluid flow in a real packed bed can be approximated as __________ model. (A) Plug flow (B) Dispersion (C) Mixed flow (D) Tank in series

Description : Fluid flow in a real packed bed can be approximated as __________ model. (A) Plug flow (B) Dispersion (C) Mixed flow (D) Tank in series

Last Answer : (B) Dispersion

From dietary protein as well as from the urea present in fluids secreted into the gastrointestinal tract intestinal bacteria produce (A) Carbondioxide (B) Ammonia (C) Ammonium sulphate (D) Creatine

Description : From dietary protein as well as from the urea present in fluids secreted into the gastrointestinal tract intestinal bacteria produce (A) Carbondioxide (B) Ammonia (C) Ammonium sulphate (D) Creatine

Last Answer : Answer : B

Asserion (A): Ethanol is miscible in all proportions with water Reason (R): Hydrogen bond is formed between water and alcohol molecules.

Description : Asserion (A): Ethanol is miscible in all proportions with water Reason (R): Hydrogen bond is formed between water and alcohol molecules.

Last Answer : Asserion (A): Ethanol is miscible in all proportions with water Reason (R): Hydrogen bond is formed between ... is false D. A is false but R is true

Ethanol and Methanol are miscible in water due to

Description : Ethanol and Methanol are miscible in water due to

Last Answer : Ethanol and Methanol are miscible in water due to A. Dissociation of water B. Their acidic character C. Allyl groups D. Hydrogen bonding

What liquids are miscible to oil?

Description : What liquids are miscible to oil?

Last Answer : Need answer

Are water and ethanol miscible?

Description : Are water and ethanol miscible?

Last Answer : Yes, in all proportions. Wine, beer and other alcoholic drinksare all such mixtures.

Distillation can be used to separate solutions of miscible liquids because ?

Description : Distillation can be used to separate solutions of miscible liquids because ?

Last Answer : Distillation works because liquids boil at different temperatures. Roughly speaking, in order to separate two liquids, you should heat the mixture to a temperature where one of the liquids (but not the ... boil off, leaving the second liquid behind; you can collect the first liquid in a condenser.

Inert gases are - (1) Miscible with water (2) Not stable (3) Chemically uncreative (4) Chemically very active

Description : Inert gases are - (1) Miscible with water (2) Not stable (3) Chemically uncreative (4) Chemically very active

Last Answer : (3) Chemically uncreative Explanation: An inert gas is a gas which does not undergo chemical reactions since their valence shells are filled, meaning they don't normally form chemical bonds with other ... inert gases, also called noble gases, are argon, helium, neon, krypton, xenon and radon.

Copper is completely miscible with (A) nickel. (B) gold. (C) hydrogen. (D) lead.

Description : Copper is completely miscible with (A) nickel. (B) gold. (C) hydrogen. (D) lead.

Last Answer : (B) gold.

Inert gases are (1) Miscible with water (2) Not stable (3) Chemically unreactive (4) Chemically very active

Description : Inert gases are (1) Miscible with water (2) Not stable (3) Chemically unreactive (4) Chemically very active

Last Answer : Chemically unreactive

Helium is added to the oxygen supply of deep sea divers because it is (1) less poisonous than nitrogen (2) Lighter than nitrogen (3) Readily miscible with oxygen (4) less soluble in blood than nitrogen at high pressure

Description : Helium is added to the oxygen supply of deep sea divers because it is (1) less poisonous than nitrogen (2) Lighter than nitrogen (3) Readily miscible with oxygen (4) less soluble in blood than nitrogen at high pressure

Last Answer : less soluble in blood than nitrogen at high pressure

Water is not effective in extinguishing a fire caused by petrol because (1) the flame is too hot for water to cool it down (2) water and petrol react chemically (3) water and petrol are miscible with each other (4) water and petrol are immiscible with each other and petrol which forms the upper layer continues to burn

Description : Water is not effective in extinguishing a fire caused by petrol because (1) the flame is too hot for water to cool it down (2) water and petrol react chemically (3) water and petrol are ... 4) water and petrol are immiscible with each other and petrol which forms the upper layer continues to burn

Last Answer : water and petrol are immiscible with each other and petrol which forms the upper layer continues to burn

What are the major problems in using pumping for concreting works?

Description : What are the major problems in using pumping for concreting works?

Last Answer : In pumping operation, the force exerted by pumps must overcome the friction between concrete and the pumping pipes, the weight of concrete and the pressure head when placing concrete above the ... other hand, a proper selection of aggregate grading helps to improve the pumpability of concrete.

The nurse teaches the patient about glargine (Lantus), a “peakless” basal insulin including which of the following statements? a) Do not mix the drug with other insulins Because glargine is in a suspension with a pH of 4, it cannot be mixed with other insulins because this would cause precipitation. When administering glargine (Lantus) insulin it is very important to read the label carefully and to avoid mistaking Lantus insulin for Lente insulin and vice versa.

Description : The nurse teaches the patient about glargine (Lantus), a peakless basal insulin including which of the following statements? a) Do not mix the drug with other insulins Because glargine is in a ... action Glargine is a peakless basal insulin that is absorbed very slowly over a 24-hour period.

Last Answer : a) Do not mix the drug with other insulins Because glargine is in a suspension with a pH of 4, it cannot be mixed with other insulins because this would cause precipitation. When administering ... to read the label carefully and to avoid mistaking Lantus insulin for Lente insulin and vice versa.

According to Water-Cement Ratio Law, the strength of workable plastic concrete (A) Depends upon the amount of water used in the mix (B) Does not depend upon the quality of cement mixed with aggregates (C) Does not depend upon the quantity of cement mixed with aggregates (D) All the above

Description : According to Water-Cement Ratio Law, the strength of workable plastic concrete (A) Depends upon the amount of water used in the mix (B) Does not depend upon the quality of cement mixed with aggregates (C) Does not depend upon the quantity of cement mixed with aggregates (D) All the above

Last Answer : Answer: Option D

If 50 kg of fine aggregates and 100 kg of coarse aggregates are mixed in a concrete whose water cement ratio is 0.6, the weight of water required for harsh mix, is (A) 8 kg (B) 10 kg (C) 12 kg (D) 14 kg

Description : If 50 kg of fine aggregates and 100 kg of coarse aggregates are mixed in a concrete whose water cement ratio is 0.6, the weight of water required for harsh mix, is (A) 8 kg (B) 10 kg (C) 12 kg (D) 14 kg

Last Answer : Answer: Option C

Pick up the incorrect statement from the following. While performing preliminary test on concrete (A) Proportions of the material and water should be the same as to be used at the work site (B) Cement should be mixed by hand in order to maintain uniformity (C) Concrete mix should be stored in air-tight containers (D) Concrete ingredients should be kept at a temperature of 37° ± 2°C

Description : Pick up the incorrect statement from the following. While performing preliminary test on concrete (A) Proportions of the material and water should be the same as to be used at the work site (B) ... in air-tight containers (D) Concrete ingredients should be kept at a temperature of 37° 2°C

Last Answer : Answer: Option D

According to the rule of water cement ratio, the strength of concrete wholly depends upon. (a) The quality of cement. (b) The quality of cement mixed with aggregate. (c) The amount of water used in preparation of concrete mix. (d) All of the above

Description : According to the rule of water cement ratio, the strength of concrete wholly depends upon. (a) The quality of cement. (b) The quality of cement mixed with aggregate. (c) The amount of water used in preparation of concrete mix. (d) All of the above

Last Answer : (c) The amount of water used in preparation of concrete mix.

I have a question about hot dip galvanizing. Is there any effect on galvanized coating if flux (zinc ammonium chloride salt) mixed inside hydrochloric acid tank instead of the normal separate hydrochloric acid tank and flux tank?

Description : I have a question about hot dip galvanizing. Is there any effect on galvanized coating if flux (zinc ammonium chloride salt) mixed inside hydrochloric acid tank instead of the normal separate hydrochloric acid tank and flux tank?

Last Answer : They should be applied separately, the acid and flux are weakening each other mixed together like that. Although they perform two separate functions in the process, both functions are necessary and are being weakened by mixing the two chemicals. You may have problems with the plating flaking off.