The _____ is equal to the number of electrons emitted per second times the electron charge ∙ a. Intensity ∙ b. Optical power ∙ c. Photocurrent ∙ d. Responsitivity

The _____ is equal to the number of electrons emitted per second times the electron charge ∙ a. Intensity  
∙ b. Optical power  
∙ c. Photocurrent  
∙ d. Responsitivity
by

1 Answer

Answer :

c. Photocurrent
by

Related questions

The _____ of a detector is the fraction of incident photons that produce a photoelectron or electron-hole pair ∙ a. Responsitivity ∙ b. Photon efficiency ∙ c. Aperture ∙ d. Quantum efficiency

Description : The _____ of a detector is the fraction of incident photons that produce a photoelectron or electron-hole pair ∙ a. Responsitivity ∙ b. Photon efficiency ∙ c. Aperture ∙ d. Quantum efficiency

Last Answer : d. Quantum efficiency

Optical detectors are square-law devices because they respond to _____ rather than amplitude ∙ a. Intensity ∙ b. Light ∙ c. Density ∙ d. Photon

Description : Optical detectors are square-law devices because they respond to _____ rather than amplitude ∙ a. Intensity ∙ b. Light ∙ c. Density ∙ d. Photon

Last Answer : a. Intensity

In solid-state optical detectors, the excited charge is transported in the solid by ∙ a. Holes and protons ∙ b. Holes and electrons ∙ c. Anion and cation ∙ d. Protons and photons

Description : In solid-state optical detectors, the excited charge is transported in the solid by ∙ a. Holes and protons ∙ b. Holes and electrons ∙ c. Anion and cation ∙ d. Protons and photons

Last Answer : ∙ b. Holes and electrons

One of the following is not a characteristic of light detectors. ∙ a. Responsitivity ∙ b. Spectral response ∙ c. Transmit time ∙ d. Dispersion

Description : One of the following is not a characteristic of light detectors. ∙ a. Responsitivity ∙ b. Spectral response ∙ c. Transmit time ∙ d. Dispersion

Last Answer : ∙ d. Dispersion

What is the unit of responsitivity? ∙ a. Ampere/volt ∙ b. Ampere/watt ∙ c. Watt/ampere ∙ d. Volts/ampere

Description : What is the unit of responsitivity? ∙ a. Ampere/volt ∙ b. Ampere/watt ∙ c. Watt/ampere ∙ d. Volts/ampere

Last Answer : ∙ a. Ampere/volt

What parameter of light detector determines the range or system length that can be achieved for a given wavelength? ∙ a. Transit time ∙ b. Spectral response ∙ c. Dark current ∙ d. Responsitivity

Description : What parameter of light detector determines the range or system length that can be achieved for a given wavelength? ∙ a. Transit time ∙ b. Spectral response ∙ c. Dark current ∙ d. Responsitivity

Last Answer : ∙ b. Spectral response

Light rays that are emitted simultaneously from an LED and propagated down an optical fiber do not arrive at the far end of the fiber at the same time results to ∙ A. intramodal dispersion ∙ B. pulse length dispersion ∙ C. modal dispersion ∙ D. wavelength dispersion

Description : Light rays that are emitted simultaneously from an LED and propagated down an optical fiber do not arrive at the far end of the fiber at the same time results to ∙ A. intramodal dispersion ∙ B. pulse length dispersion ∙ C. modal dispersion ∙ D. wavelength dispersion

Last Answer : D. wavelength dispersion

The law that states “When visible light of high frequency electromagnetic radiation illuminates a metallic surface, electrons are emitted” is known as ____________. ∙ A. Einstein law of photon ∙ B. Marconi’s law ∙ C. Maxwell’s law ∙ D. Plank’s law

Description : The law that states “When visible light of high frequency electromagnetic radiation illuminates a metallic surface, electrons are emitted” is known as ____________. ∙ A. Einstein law of photon ∙ B. Marconi’s law ∙ C. Maxwell’s law ∙ D. Plank’s law

Last Answer : D. Plank’s law

Which modulation methods are the most widely used in optical systems? ∙ a. Phase and frequency modulations ∙ b. Polarization modulation and phase modulation ∙ c. Intensity modulation and phase modulation ∙ d. Intensity modulation and polarization modulation

Description : Which modulation methods are the most widely used in optical systems? ∙ a. Phase and frequency modulations ∙ b. Polarization modulation and phase modulation ∙ c. Intensity modulation and phase modulation ∙ d. Intensity modulation and polarization modulation

Last Answer : Intensity modulation and polarization modulation

An increase in light intensity produces fast optic switching due to ∙ a. Increase in index of glass ∙ b. Amplification of optical signal ∙ c. High gain ∙ d. Photoconductivity

Description : An increase in light intensity produces fast optic switching due to ∙ a. Increase in index of glass ∙ b. Amplification of optical signal ∙ c. High gain ∙ d. Photoconductivity

Last Answer : b. Amplification of optical signal

Which is the proper measurement of average power emitted by a pulsed laser? ∙ a. Energy x time ∙ b. Pulse energy x repetition rate ∙ c. Pulse energy / repetition rate ∙ d. Peak power x pulse length

Description : Which is the proper measurement of average power emitted by a pulsed laser? ∙ a. Energy x time ∙ b. Pulse energy x repetition rate ∙ c. Pulse energy / repetition rate ∙ d. Peak power x pulse length

Last Answer : ∙ b. Pulse energy x repetition rate

Optical fibers for telecommunications are typically about _____ mils thick and consists of a glass core, a glass cladding of lower index of refraction, and a protective coating ∙ a. 5 ∙ b. 6 ∙ c. 7 ∙ d. 8

Description : Optical fibers for telecommunications are typically about _____ mils thick and consists of a glass core, a glass cladding of lower index of refraction, and a protective coating ∙ a. 5 ∙ b. 6 ∙ c. 7 ∙ d. 8

Last Answer : ∙ a. 5

The graded-index multimode optical fiber has a core diameter of _____ nm. ∙ a. 0.5 ∙ b. 0.05 ∙ c. 0.0005 ∙ d. 5

Description : The graded-index multimode optical fiber has a core diameter of _____ nm. ∙ a. 0.5 ∙ b. 0.05 ∙ c. 0.0005 ∙ d. 5

Last Answer : ∙ a. 0.5

A step-index multimode optical fiber has a core diameter of _____ nm. ∙ a. 0.02 ∙ b. 0.2 ∙ c. 2 ∙ d. 0.002

Description : A step-index multimode optical fiber has a core diameter of _____ nm. ∙ a. 0.02 ∙ b. 0.2 ∙ c. 2 ∙ d. 0.002

Last Answer : b. 0.2

A single mode optical fiber has a core diameter of _____ nm. ∙ a. 0.1 ∙ b. 0.01 ∙ c. 0.2 ∙ d. 0.05

Description : A single mode optical fiber has a core diameter of _____ nm. ∙ a. 0.1 ∙ b. 0.01 ∙ c. 0.2 ∙ d. 0.05

Last Answer : a. 0.1

Cable attenuation is usually expressed in terms of ∙ A. loss per foot ∙ B. dB/km ∙ C. intensity per mile ∙ D. voltage drop per inch

Description : Cable attenuation is usually expressed in terms of ∙ A. loss per foot ∙ B. dB/km ∙ C. intensity per mile ∙ D. voltage drop per inch

Last Answer : . dB/km

Light intensity is generally described in terms of __________ and measured in _________. ∙ A. Luminous flux density; Lumens per unit area ∙ B. Luminous flux intensity; Lumens per unit area ∙ C. Luminous flux density; Lumens per unit volume ∙ D. Luminous flux intensity; Lumens per unit volume

Description : Light intensity is generally described in terms of __________ and measured in _________. ∙ A. Luminous flux density; Lumens per unit area ∙ B. Luminous flux intensity; Lumens per unit area ∙ C. Luminous flux density; Lumens per unit volume ∙ D. Luminous flux intensity; Lumens per unit volume

Last Answer : Luminous flux density; Lumens per unit area

Cable attenuation is usually expressed in terms of ∙ a. Loss per foot ∙ b. dB/km ∙ c. intensity per mile ∙ d. voltage drop per inch

Description : Cable attenuation is usually expressed in terms of ∙ a. Loss per foot ∙ b. dB/km ∙ c. intensity per mile ∙ d. voltage drop per inch

Last Answer : ∙ b. dB/km

Is the different angle of entry of light into an optical fiber when the diameter of the core is many times the wavelength of the light transmitted. ∙ a. Acceptance angle ∙ b. Modes ∙ c. Sensors ∙ d. Aperture

Description : Is the different angle of entry of light into an optical fiber when the diameter of the core is many times the wavelength of the light transmitted. ∙ a. Acceptance angle ∙ b. Modes ∙ c. Sensors ∙ d. Aperture

Last Answer : b. Modes

What is the typical wavelength of light emitted from epitaxially grown LEDs? ∙ a. 840 nm ∙ b. 490 nm ∙ c. 480 nm ∙ d. 940 nm

Description : What is the typical wavelength of light emitted from epitaxially grown LEDs? ∙ a. 840 nm ∙ b. 490 nm ∙ c. 480 nm ∙ d. 940 nm

Last Answer : ∙ d. 940 nm

The first laser emitted ∙ a. Pulses of 694 nm red light ∙ b. A continuous red beam ∙ c. Pulses of white light from a helical flash lamp ∙ d. Spontaneous emission

Description : The first laser emitted ∙ a. Pulses of 694 nm red light ∙ b. A continuous red beam ∙ c. Pulses of white light from a helical flash lamp ∙ d. Spontaneous emission

Last Answer : ∙ a. Pulses of 694 nm red light

Is the width of the range of wavelengths emitted by the light source ∙ a. Bandwidth ∙ b. Chromatic Dispersion ∙ c. Spectral width ∙ d. Beamwidth

Description : Is the width of the range of wavelengths emitted by the light source ∙ a. Bandwidth ∙ b. Chromatic Dispersion ∙ c. Spectral width ∙ d. Beamwidth

Last Answer : c. Spectral width

The minimum optical power a light detector can receive and still produce a usable electrical output signal. ∙ A. light responsivity ∙ B. light sensitivity ∙ C. light collectivity ∙ D. illumination

Description : The minimum optical power a light detector can receive and still produce a usable electrical output signal. ∙ A. light responsivity ∙ B. light sensitivity ∙ C. light collectivity ∙ D. illumination

Last Answer : B. light sensitivity

The term responsivity as it applies to a light detector is best described as ∙ A. the time required for the signal to go from 10 to 90 percent of maximum amplitude ∙ B. the ratio of the diode output current to the input optical power ∙ C. the ratio of the input power to output power ∙ D. the ratio of output current to input current

Description : The term responsivity as it applies to a light detector is best described as ∙ A. the time required for the signal to go from 10 to 90 percent of maximum amplitude ∙ B. the ratio of the diode ... . the ratio of the input power to output power ∙ D. the ratio of output current to input current

Last Answer : the ratio of the diode output current to the input optical power

For a single mode optical cable with 0.25 dB/km loss, determine the optical power 100 km from a 0.1-mW light source. ∙ A. -45 dBm ∙ B. -15 dBm ∙ C. -35 dBm

Description : For a single mode optical cable with 0.25 dB/km loss, determine the optical power 100 km from a 0.1-mW light source. ∙ A. -45 dBm ∙ B. -15 dBm ∙ C. -35 dBm

Last Answer : ∙ C. -35 dBm

Optical power is sometimes called __________. ∙ A. Radiant emission ∙ B. Radiant power ∙ C. Radiant flux ∙ D. Radiant optics

Description : Optical power is sometimes called __________. ∙ A. Radiant emission ∙ B. Radiant power ∙ C. Radiant flux ∙ D. Radiant optics

Last Answer : C. Radiant flux

It is described as the flow of light energy past a given point in a specified time ∙ A. Optical radiation ∙ B. Optical impedance ∙ C. Optical illusion ∙ D. Optical power

Description : It is described as the flow of light energy past a given point in a specified time ∙ A. Optical radiation ∙ B. Optical impedance ∙ C. Optical illusion ∙ D. Optical power

Last Answer : D. Optical power

In radiometric terms, it measures the rate at which electromagnetic waves transfer light energy ∙ A. Optical radiation ∙ B. Optical impedance ∙ C. Optical illusion ∙ D. Optical power

Description : In radiometric terms, it measures the rate at which electromagnetic waves transfer light energy ∙ A. Optical radiation ∙ B. Optical impedance ∙ C. Optical illusion ∙ D. Optical power

Last Answer : D. Optical power

Used to test a fiber optics splice ∙ a. Spectrum analyzer ∙ b. Oscilloscope ∙ c. Optical power meter ∙ d. Field strength meter

Description : Used to test a fiber optics splice ∙ a. Spectrum analyzer ∙ b. Oscilloscope ∙ c. Optical power meter ∙ d. Field strength meter

Last Answer : c. Optical power meter

Optical cable testers are used for ∙ a. Checking refractive index ∙ b. Light power out of a fiber ∙ c. Non-calibrated light into a fiber

Description : Optical cable testers are used for ∙ a. Checking refractive index ∙ b. Light power out of a fiber ∙ c. Non-calibrated light into a fiber

Last Answer : b. Light power out of a fiber

Optical cable testers are used for ∙ a. Checking refractive index ∙ b. Light power out of a fiber ∙ c. Non-calibrated light into a fiber

Description : Optical cable testers are used for ∙ a. Checking refractive index ∙ b. Light power out of a fiber ∙ c. Non-calibrated light into a fiber

Last Answer : ∙ b. Light power out of a fiber

What is a specific path the light takes in an optical fiber corresponding to a certain angle and number of reflection ∙ a. Mode ∙ b. Grade ∙ c. Numerical Aperture ∙ d. Dispersion

Description : What is a specific path the light takes in an optical fiber corresponding to a certain angle and number of reflection ∙ a. Mode ∙ b. Grade ∙ c. Numerical Aperture ∙ d. Dispersion

Last Answer : a. Mode

Which of the following is not a part of the optical spectrum? ∙ A. infrared ∙ B. ultraviolet ∙ C. visible color ∙ D. x-rays

Description : Which of the following is not a part of the optical spectrum? ∙ A. infrared ∙ B. ultraviolet ∙ C. visible color ∙ D. x-rays

Last Answer : ∙ D. x-rays

For a 300-m optical fiber cable with a bandwidth distance product of 600 MHz-km, determine the bandwidth. ∙ A. 5 GHz ∙ B. 1 GHz ∙ C. 2 GHz

Description : For a 300-m optical fiber cable with a bandwidth distance product of 600 MHz-km, determine the bandwidth. ∙ A. 5 GHz ∙ B. 1 GHz ∙ C. 2 GHz

Last Answer : C. 2 GHz

A type of index of an optical fiber that has no cladding and whose central core has a non-uniform refractive index. ∙ A. graded index ∙ B. multimode ∙ C. single mode ∙ D. step-index

Description : A type of index of an optical fiber that has no cladding and whose central core has a non-uniform refractive index. ∙ A. graded index ∙ B. multimode ∙ C. single mode ∙ D. step-index

Last Answer : ∙ A. graded index

A type of index profile of an optical fiber that has a central core and outside cladding with a uniform refractive index ∙ A. multimode ∙ B. graded index ∙ C. step-index ∙ D. single mode

Description : A type of index profile of an optical fiber that has a central core and outside cladding with a uniform refractive index ∙ A. multimode ∙ B. graded index ∙ C. step-index ∙ D. single mode

Last Answer : ∙ C. step-index

The three major groups of the optical system are ∙ A. the components, the data rate and the response time ∙ B. the source, the link and the receiver ∙ C. the transmitter, the cable and the receiver ∙ D. the source, the link and the detector

Description : The three major groups of the optical system are ∙ A. the components, the data rate and the response time ∙ B. the source, the link and the receiver ∙ C. the transmitter, the cable and the receiver ∙ D. the source, the link and the detector

Last Answer : B. the source, the link and the receiver

Developed an optical fiber with losses less that 2 dB/km ∙ A. Kao and Bockham ∙ B. Maiman, Kao and Bockham ∙ C. Maiman and Schawlow ∙ D. Kapron, Keck and Maurer

Description : Developed an optical fiber with losses less that 2 dB/km ∙ A. Kao and Bockham ∙ B. Maiman, Kao and Bockham ∙ C. Maiman and Schawlow ∙ D. Kapron, Keck and Maurer

Last Answer : ∙ A. Kao and Bockham

The scientist who built the first optical maser ∙ A. Charles Townes ∙ B. GA Bockham ∙ C. Theodore Maiman ∙ D. ACS Van Heel

Description : The scientist who built the first optical maser ∙ A. Charles Townes ∙ B. GA Bockham ∙ C. Theodore Maiman ∙ D. ACS Van Heel

Last Answer : ∙ C. Theodore Maiman

Approximately what is the frequency limit of the optical fiber? ∙ A. 20 MHz ∙ B. 1 MHz ∙ C. 100 MHz ∙ D. 40 GHz

Description : Approximately what is the frequency limit of the optical fiber? ∙ A. 20 MHz ∙ B. 1 MHz ∙ C. 100 MHz ∙ D. 40 GHz

Last Answer : ∙ D. 40 GHz

What is the frequency limit of an optical fiber? ∙ a. 20 GHz ∙ b. 30 GHz ∙ c. 40 GHz ∙ d. 50 GHz

Description : What is the frequency limit of an optical fiber? ∙ a. 20 GHz ∙ b. 30 GHz ∙ c. 40 GHz ∙ d. 50 GHz

Last Answer : ∙ c. 40 GHz

Which optical detector is used when high sensitivity and bandwidth are required? ∙ a. PMT ∙ b. APD ∙ c. PIN ∙ d. Phototransistor

Description : Which optical detector is used when high sensitivity and bandwidth are required? ∙ a. PMT ∙ b. APD ∙ c. PIN ∙ d. Phototransistor

Last Answer : a. PMT

One of the following is not a solid-state optical detector ∙ a. APD ∙ b. PIN ∙ c. PMT ∙ d. Phototransistors

Description : One of the following is not a solid-state optical detector ∙ a. APD ∙ b. PIN ∙ c. PMT ∙ d. Phototransistors

Last Answer : . PMT

Light traveling in optical fiber follows which of the following principles. ∙ a. Huygen’s principle ∙ b. Reflection theory ∙ c. Light theory ∙ d. Snell’s law

Description : Light traveling in optical fiber follows which of the following principles. ∙ a. Huygen’s principle ∙ b. Reflection theory ∙ c. Light theory ∙ d. Snell’s law

Last Answer : d. Snell’s law

An IC that represents a short distance one-way optical communications ∙ a. Optoisolator ∙ b. Insulator ∙ c. Multivibrator ∙ d. Optical IC

Description : An IC that represents a short distance one-way optical communications ∙ a. Optoisolator ∙ b. Insulator ∙ c. Multivibrator ∙ d. Optical IC

Last Answer : a. Optoisolator

Which is not a possible cause of optical fiber loss? ∙ a. Impurities ∙ b. Glass attenuation ∙ c. Stepped index operation ∙ d. Microbending

Description : Which is not a possible cause of optical fiber loss? ∙ a. Impurities ∙ b. Glass attenuation ∙ c. Stepped index operation ∙ d. Microbending

Last Answer : ∙ c. Stepped index operation

OTDR stands for ∙ a. Optical Time Domain Reflectometer ∙ b. Optical Transmit Direction Return ∙ c. Optical Time Domain Time Regeneration ∙ d. Overtime Direct Reference

Description : OTDR stands for ∙ a. Optical Time Domain Reflectometer ∙ b. Optical Transmit Direction Return ∙ c. Optical Time Domain Time Regeneration ∙ d. Overtime Direct Reference

Last Answer : c. Optical Time Domain Time Regeneration

SONET stands for ∙ a. System Optical Network ∙ b. Synchronous Optical Network ∙ c. Silica Optic Network ∙ d. System Optical Fiber Net

Description : SONET stands for ∙ a. System Optical Network ∙ b. Synchronous Optical Network ∙ c. Silica Optic Network ∙ d. System Optical Fiber Net

Last Answer : ∙ b. Synchronous Optical Network

The ultrapure glass used to manufacture optical fibers is approximately ___pure ∙ a. 99.9 % ∙ b. 99.99 % ∙ c. 99.999 % ∙ d. 99.9999 %

Description : The ultrapure glass used to manufacture optical fibers is approximately ___pure ∙ a. 99.9 % ∙ b. 99.99 % ∙ c. 99.999 % ∙ d. 99.9999 %

Last Answer : d. 99.9999 %

Which of the following is not part of the optical spectrum? ∙ a. Infrafed ∙ b. Ultraviolet ∙ c. Visible color ∙ d. X-rays

Description : Which of the following is not part of the optical spectrum? ∙ a. Infrafed ∙ b. Ultraviolet ∙ c. Visible color ∙ d. X-rays

Last Answer : ∙ d. X-rays