What type of cooling is used to control ambient room temperature?

What type of cooling is used to control ambient room  temperature?
by

1 Answer

Answer :

Air conditioning.
by

Related questions

What type of bias is used where only moderate changes in ambient temperature are expected?

Description : What type of bias is used where only moderate changes in ambient temperature are expected?

Last Answer : Self-bias.

The minimum temperature to which the water can be cooled in a cooling tower is the __________ temperature of air. (A) Ambient (B) Dry bulb (C) Dew point (D) Wet bulb

Description : The minimum temperature to which the water can be cooled in a cooling tower is the __________ temperature of air. (A) Ambient (B) Dry bulb (C) Dew point (D) Wet bulb

Last Answer : C) Dew point

The cooling water reduces the water temperature close to _____. • Dry bulb temperature • Ambient wet bulb temperature • Dew point temperature • None of the above

Description : The cooling water reduces the water temperature close to _____. • Dry bulb temperature • Ambient wet bulb temperature • Dew point temperature • None of the above

Last Answer : Ambient wet bulb temperature

State why it is important for you to consider the ambient (surrounding) temperature of a conductor when selecting wire size.

Description : State why it is important for you to consider the ambient (surrounding) temperature of a conductor when selecting wire size.

Last Answer : The heat surrounding the conductor is an important part of total conductor heating.

Electric motors intended for use outside the engine room and boiler room are frequently rated to run at a designed ambient temperature of 40°C. What is the equivalent temperature in degrees Fahrenheit? A. 54.2°F B. 72.0°F C. 104.0°F D. 129.6°F

Description : Electric motors intended for use outside the engine room and boiler room are frequently rated to run at a designed ambient temperature of 40°C. What is the equivalent temperature in degrees Fahrenheit? A. 54.2°F B. 72.0°F C. 104.0°F D. 129.6°F

Last Answer : Answer: C

Ambient temperature is the _____________. A. amount of temperature rise with no load B. amount of temperature developed by an operating motor C. temperature of the compartment where the motor is located D. normal operating temperature, less the room temperature

Description : Ambient temperature is the _____________. A. amount of temperature rise with no load B. amount of temperature developed by an operating motor C. temperature of the compartment where the motor is located D. normal operating temperature, less the room temperature

Last Answer : Answer: C

Ambient temperature is the _____________. A. amount of temperature rise with no load B. temperature of the compartment where the motor is located C. normal operating temperature, less the room temperature D. amount of temperature developed by an operating motor

Description : Ambient temperature is the _____________. A. amount of temperature rise with no load B. temperature of the compartment where the motor is located C. normal operating temperature, less the room temperature D. amount of temperature developed by an operating motor

Last Answer : Answer: B

Two contributors of electronic console failures are heat and vibration. To combat some of their effects, preventive maintenance procedures should include ______________. A. systematic rotation of circuit cards with those from spares to allow component cooling B. periodic changing or cleaning of console ventilation and control room air conditioning filters C. weekly tightening of console foundation bolts and changing of the air in the control room D. all of the above

Description : Two contributors of electronic console failures are heat and vibration. To combat some of their effects, preventive maintenance procedures should include ______________. A. systematic rotation of circuit cards with those ... bolts and changing of the air in the control room D. all of the above

Last Answer : Answer: B

The process of gradual cooling of glass articles to room temperature is called

Description : The process of gradual cooling of glass articles to room temperature is called

Last Answer : annealing.

Air intake for an air compressor should be preferably taken from (A) A site, where cooling towers are located nearby (B) A site, where open coal yard in located nearby (C) An air conditioned room maintained at a temperature of 18°C (D) An outside atmosphere at 10°C

Description : Air intake for an air compressor should be preferably taken from (A) A site, where cooling towers are located nearby (B) A site, where open coal yard in located nearby (C) An air conditioned room maintained at a temperature of 18°C (D) An outside atmosphere at 10°C

Last Answer : (D) An outside atmosphere at 10°C

The heat released by cooling one mole of copper from 400 K to room temperature (300 K) is (assume : Cp of copper is 23 J K-1mole-1) (A) 2300 J (B) 4600 J (C) 230 J (D) 2.3 × 106 J

Description : The heat released by cooling one mole of copper from 400 K to room temperature (300 K) is (assume : Cp of copper is 23 J K-1mole-1) (A) 2300 J (B) 4600 J (C) 230 J (D) 2.3 × 106 J

Last Answer : A) 2300 J

Heating the Hypo-eutectoid steels to 30°C above the upper critical temperature line, soaking at that temperature and then cooling slowly to the room temperature to form a pearlite & ferrite structure is called (A) Tempering (B) Hardening (C) Annealing (D) Normalising

Description : Heating the Hypo-eutectoid steels to 30°C above the upper critical temperature line, soaking at that temperature and then cooling slowly to the room temperature to form a pearlite & ferrite structure is called (A) Tempering (B) Hardening (C) Annealing (D) Normalising

Last Answer : Option C

What is the ambient temperature in hammer-space?

Description : What is the ambient temperature in hammer-space?

Last Answer : The temperature of hammerspace is around 294 degrees Kelvin. This temperature is maintained by the transdimensional fold or warp energy produced when objects are brought into or taken out of hammerspace. To ... to the second law of thermodynamics, is manifested as heat. Doesn't everyone know that?

How do humans (mammals) maintain body temperature when the ambient temperature is higher than body normal?

Description : How do humans (mammals) maintain body temperature when the ambient temperature is higher than body normal?

Last Answer : Sweat.

Standard air is the: a. Mass of 1 cubic meter of dry air at 20°C and atmospheric pressure b. Mass of a cubic meter of air at atmospheric conditions c. Volume of air at ambient temperature and atmospheric pressure d. Volume of 1 kg of dry air at 21°C and atmospheric pressure at sea level or 101.325 kPa e. Volume of 1 kg of air at 15°C and 100 kPa

Description : Standard air is the: a. Mass of 1 cubic meter of dry air at 20°C and atmospheric pressure b. Mass of a cubic meter of air at atmospheric conditions c. Volume of air at ambient temperature and atmospheric pressure ... pressure at sea level or 101.325 kPa e. Volume of 1 kg of air at 15°C and 100 kPa

Last Answer : Answer: D

The _____________ sensor, checks the temperature of the ambient air entering the engine for fine tuning the mixture strength. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Description : The _____________ sensor, checks the temperature of the ambient air entering the engine for fine tuning the mixture strength. a) engine temperature b) exhaust gas c) air flow d) air inlet temperature

Last Answer : Answer: d Explanation: The air inlet temperature sensor, checks the temperature of the ambient air entering the engine for fine tuning the mixture strength whereas the engine temperature sensor senses the ... gas senor senses the amount of oxygen in the engine exhaust and calculates air-fuel ratio.

Which one of the following statement is not correct for the volumetric efficiency of a reciprocating air compressor? A. It decreases with increase in ambient temperature B. It increases with decrease in pressure ratio C. It increases with decrease in clearance ratio D. It decreases with increases in delivery pressure

Description : Which one of the following statement is not correct for the volumetric efficiency of a reciprocating air compressor? A. It decreases with increase in ambient temperature B. It increases with ... It increases with decrease in clearance ratio D. It decreases with increases in delivery pressure

Last Answer : ANSWER : A

The ink of a pen leaks out in an airplane because (a) Atmospheric pressure increases (b) Pressure of ink inside is more than the ambient pressure (c) High speed of the aeroplane (d) Temperature difference

Description : The ink of a pen leaks out in an airplane because (a) Atmospheric pressure increases (b) Pressure of ink inside is more than the ambient pressure (c) High speed of the aeroplane (d) Temperature difference

Last Answer : Ans:(b)

Unless it can be shown that a 45°C ambient temperature will not be exceeded, motors within a machinery space must be designed for an ambient temperature of _____________. A. 45°C B. 50°C C. 55°C D. 60°C

Description : Unless it can be shown that a 45°C ambient temperature will not be exceeded, motors within a machinery space must be designed for an ambient temperature of _____________. A. 45°C B. 50°C C. 55°C D. 60°C

Last Answer : Answer: B

Which of the following statements describes the effects of ambient temperature on local action within lead-acid storage batteries? A. Increasing ambient temperature increases local action. B. Increasing ambient temperature decreases local action. C. Ambient temperature has no effect on local action. D. At 90°F all local action virtually ceases.

Description : Which of the following statements describes the effects of ambient temperature on local action within lead-acid storage batteries? A. Increasing ambient temperature increases local action. B. Increasing ambient ... has no effect on local action. D. At 90°F all local action virtually ceases.

Last Answer : Answer: A

In preparing to take insulation resistance readings on a main generator, the windings should be grounded for about 15 minutes prior to the test to _____________. A. allow accurate zeroing of the meter B. help the windings to cool to ambient temperature C. release any residual capacitive charge from the windings D. help the windings to cool to the same temperature as the ground test connection

Description : In preparing to take insulation resistance readings on a main generator, the windings should be grounded for about 15 minutes prior to the test to _____________. A. allow accurate zeroing of the meter ... the windings D. help the windings to cool to the same temperature as the ground test connection

Last Answer : Answer: C

If a DC motor runs hot, the cause may be _____________. A. high mica condition B. low ambient temperature C. clogged ventilation ducts D. an open in the shunt field

Description : If a DC motor runs hot, the cause may be _____________. A. high mica condition B. low ambient temperature C. clogged ventilation ducts D. an open in the shunt field

Last Answer : Answer: C

A disadvantage of using the configuration in the illustrated circuit is _________. EL-0045 A. no current gain B. high input resistance C. high voltage gain D. becomes unstable with an increase of ambient temperature

Description : A disadvantage of using the configuration in the illustrated circuit is _________. EL-0045 A. no current gain B. high input resistance C. high voltage gain D. becomes unstable with an increase of ambient temperature

Last Answer : Answer: A

One item listed on the name plate of a cargo pump motor is 'degrees centigrade rise.' This number is based on _____________. A. normal temperature change from cold to hot B. an ambient temperature of 40°C C. minimum heat rise from no load to full load D. maximum degrees centigrade rise from absolute zero

Description : One item listed on the name plate of a cargo pump motor is 'degrees centigrade rise.' This number is based on _____________. A. normal temperature change from cold to hot B. an ambient temperature ... . minimum heat rise from no load to full load D. maximum degrees centigrade rise from absolute zero

Last Answer : Answer: B

Which of the listed conditions could indicate the need for cleaning electrical insulation? A. Low ambient temperature B. Low operating temperature C. High dielectric strength D. Low megger readings

Description : Which of the listed conditions could indicate the need for cleaning electrical insulation? A. Low ambient temperature B. Low operating temperature C. High dielectric strength D. Low megger readings

Last Answer : Answer: D

Motor name plate data includes '°°C rise'. This indicates the _____________. A. actual running temperature of the winding from no load to full load B. permissible temperature rise of the windings above the designed ambient temperature C. maximum allowable temperature rise above normal full load operating temperature D. maximum allowable temperature rise for continuous no load service

Description : Motor name plate data includes '°°C rise'. This indicates the _____________. A. actual running temperature of the winding from no load to full load B. permissible temperature rise ... above normal full load operating temperature D. maximum allowable temperature rise for continuous no load service

Last Answer : Answer: B

Magnetic controller contacts may become welded together during operating conditions as a result of _____________. A. high spring pressure B. high ambient temperature C. an open coil D. low voltage on operating coil

Description : Magnetic controller contacts may become welded together during operating conditions as a result of _____________. A. high spring pressure B. high ambient temperature C. an open coil D. low voltage on operating coil

Last Answer : Answer: D

Magnetic controller contacts may become welded together during operation because of _____________. A. excessive magnetic gap B. low contact pressure C. an open coil D. excessive ambient temperature

Description : Magnetic controller contacts may become welded together during operation because of _____________. A. excessive magnetic gap B. low contact pressure C. an open coil D. excessive ambient temperature

Last Answer : Answer: B

When troubleshooting a magnetic controller, it is found that the contacts are welded together. The most probable cause is _____________. A. excessive operation at low load B. high ambient temperature C. low voltage on the operating coil D. high voltage on the operating coil

Description : When troubleshooting a magnetic controller, it is found that the contacts are welded together. The most probable cause is _____________. A. excessive operation at low load B. high ambient temperature C. low voltage on the operating coil D. high voltage on the operating coil

Last Answer : Answer: C

Magnetic controller contacts may become welded together during operation due to _____________. A. an open coil B. low contact pressure C. excessive ambient temperature D. excessive magnetic gap

Description : Magnetic controller contacts may become welded together during operation due to _____________. A. an open coil B. low contact pressure C. excessive ambient temperature D. excessive magnetic gap

Last Answer : Answer: B

Electric strip heaters are used in motor controllers to _____________. A. prevent freezing of movable contacts B. keep the components at their design ambient temperature C. prevent condensation of moisture D. minimize resistance in internal circuits

Description : Electric strip heaters are used in motor controllers to _____________. A. prevent freezing of movable contacts B. keep the components at their design ambient temperature C. prevent condensation of moisture D. minimize resistance in internal circuits

Last Answer : Answer: C

Which of the following statements describes the significance of ambient temperature in relation to the service life of electronic components? A. Ambient temperature should be as high as possible to drive off moisture. B. Increased ambient temperature decreases the service life of electronic components. C. Ambient temperature is not significant as long as the relative humidity is kept low. D. A reduced ambient temperature causes a corresponding reduced service life.

Description : Which of the following statements describes the significance of ambient temperature in relation to the service life of electronic components? A. Ambient temperature should be as high as possible to drive ... is kept low. D. A reduced ambient temperature causes a corresponding reduced service life.

Last Answer : Answer: B

The rated temperature rise of an electric motor is the _____________. A. average temperature at any given latitude B. normal temperature rise above the standard ambient temperature at rated load C. average temperature rise due to resistance at 10% overload D. permissible difference in the ambient temperature of the motor due to existing weather conditions

Description : The rated temperature rise of an electric motor is the _____________. A. average temperature at any given latitude B. normal temperature rise above the standard ambient temperature at rated load ... D. permissible difference in the ambient temperature of the motor due to existing weather conditions

Last Answer : Answer: B

When choosing a battery for a particular application, major consideration should be given to the battery's ____________. A. amp-hour capacity B. terminal polarity C. stability under charge D. ambient temperature rise

Description : When choosing a battery for a particular application, major consideration should be given to the battery's ____________. A. amp-hour capacity B. terminal polarity C. stability under charge D. ambient temperature rise

Last Answer : Answer: A

An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Description : An amplifier operating over the frequency range of 455 to 460 kHz has a 200 kΩ input resistor. What is the RMS noise voltage at the input to this amplifier if the ambient temperature is 17˚C ? A. 40 µV B. 4.0 µV C. 400 µV

Last Answer : B. 4.0 µV

Two resistors, 20kΩ, and 50kΩ are at ambient temperature. Calculate for a bandwidth equal to 100kHz, the thermal noise voltage for the two resistors connected in parallel. A. 0.4782µV B. 4278 µV C. 4.78 µV D. 47.8 µV

Description : Two resistors, 20kΩ, and 50kΩ are at ambient temperature. Calculate for a bandwidth equal to 100kHz, the thermal noise voltage for the two resistors connected in parallel. A. 0.4782µV B. 4278 µV C. 4.78 µV D. 47.8 µV

Last Answer : C. 4.78 µV

Breathing loss" on storage of gasoline occurs due to the (A) Presence of unsaturated air (B) Fluctuation of ambient temperature during day and night (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Breathing loss" on storage of gasoline occurs due to the (A) Presence of unsaturated air (B) Fluctuation of ambient temperature during day and night (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (B) Fluctuation of ambient temperature during day and night

Boiling point diagram is not affected by the ambient (A) Pressure (B) Humidity (C) Temperature (D) Both (B) and (C)

Description : Boiling point diagram is not affected by the ambient (A) Pressure (B) Humidity (C) Temperature (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

For the air water system under ambient conditions, the adiabatic saturation temperature and the wet bulb temperature are nearly equal, because (A) Water has a high latent heat of evaporation (B) Lewis number is close to unity (C) They are always equal under all circumstances

Description : For the air water system under ambient conditions, the adiabatic saturation temperature and the wet bulb temperature are nearly equal, because (A) Water has a high latent heat of evaporation (B) Lewis number is close to unity (C) They are always equal under all circumstances

Last Answer : (A) Water has a high latent heat of evaporation

Decoction refers to the use of solvent (A) At ambient temperature (B) At its boiling point (C) In its vapor form (D) None of these

Description : Decoction refers to the use of solvent (A) At ambient temperature (B) At its boiling point (C) In its vapor form (D) None of these

Last Answer : (B) At its boiling point

For a given ambient air temperature with increase in the thickness of insulation of a hot cylindrical pipe, the rate of heat loss from the surface would (A) Decrease(B) Increase(C) First decrease and then increase(D) First increase and then decrease

Description : For a given ambient air temperature with increase in the thickness of insulation of a hot cylindrical pipe, the rate of heat loss from the surface would (A) Decrease (B) Increase (C) First decrease and then increase (D) First increase and then decrease

Last Answer : (D) First increase and then decrease

Heat transfer by radiation between two bodies at T1 & T2 and in an ambient temperature of Ta °C depends on (A) T1 - T2 (B) T1 - Ta (C) T2 - Ta (D) None of these

Description : Heat transfer by radiation between two bodies at T1 & T2 and in an ambient temperature of Ta °C depends on (A) T1 - T2 (B) T1 - Ta (C) T2 - Ta (D) None of these

Last Answer : (D) None of these

. The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C and the heat transfer co-efficient between the outer surface of wall and air is 20 W.m-2 .°C-1 . The rate of heat loss from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Description : . The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C ... from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Last Answer : (A) 165.4

Shrinkage volume in cement setting does not depend upon the (A) Sand to cement ratio (B) Water to cement ratio (C) Ambient temperature fluctuation (D) Drying period

Description : Shrinkage volume in cement setting does not depend upon the (A) Sand to cement ratio (B) Water to cement ratio (C) Ambient temperature fluctuation (D) Drying period

Last Answer : (A) Sand to cement ratio

Exposure to __________ accelerates the degradation of plastics. (A) Ultraviolet radiation (B) High atmospheric temperature (C) High ambient temperature (D) Damp atmosphere

Description : Exposure to __________ accelerates the degradation of plastics. (A) Ultraviolet radiation (B) High atmospheric temperature (C) High ambient temperature (D) Damp atmosphere

Last Answer : A) Ultraviolet radiation

A thin, flat & square plate measuring 2 m × 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will remain constant at 30°C, if the convective heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Description : A thin, flat & square plate measuring 2 m 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will ... heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Last Answer : (B) 100

High relative humidity decreases the evaporative process and as the temperature is increased, the relative humidity decreases. The comfort range for human body is the ambient temperature of 22 to 27°C with relative humidity ranging from __________ percent. (A) 5 to 10 (B) 15 to 25 (C) 45 to 50 (D) 75 to 80

Description : High relative humidity decreases the evaporative process and as the temperature is increased, the relative humidity decreases. The comfort range for human body is the ambient temperature of 22 to 27°C with relative humidity ranging from __________ ... to 10 (B) 15 to 25 (C) 45 to 50 (D) 75 to 80

Last Answer : (C) 45 to 50

At 100% relative humidity, the dew point temperature of moist air is (A) Less than the wet bulb temperature (B) More than the wet bulb temperature (C) Equal to the wet bulb temperature (D) Equal to the ambient temperature

Description : At 100% relative humidity, the dew point temperature of moist air is (A) Less than the wet bulb temperature (B) More than the wet bulb temperature (C) Equal to the wet bulb temperature (D) Equal to the ambient temperature

Last Answer : (B) More than the wet bulb temperature

A supercharger is used in the engines of earthmoving machines at higher altitudes because (a) The ambient atmospheric pressure is less at higher altitudes (b) Four-cycle engines depend on the suction of the engines for the supply of air (c) Two-cycle engines are not rugged enough for higher altitude (d) The ambient temperature is less as the altitude is higher

Description : A supercharger is used in the engines of earthmoving machines at higher altitudes because (a) The ambient atmospheric pressure is less at higher altitudes (b) Four-cycle engines depend on the suction ... rugged enough for higher altitude (d) The ambient temperature is less as the altitude is higher

Last Answer : (a) The ambient atmospheric pressure is less at higher altitudes

Which of the following statements regarding evacuated tube collectors (ETC) are true? i) ETC is used for high temperatures upto 150oC ii) because of use of vacuum between two concentric glass tube, higher amount of heat is retained in ETC iii) heat loss due to conduction back to atmosphere from ETC is high iv) performance of evacuated tube is highly dependent upon the ambient temperature i & iii b) ii & iii c) i & iv d) i & ii

Description : Which of the following statements regarding evacuated tube collectors (ETC) are true? i) ETC is used for high temperatures upto 150oC ii) because of use of vacuum between two concentric glass tube, higher amount of heat is ... upon the ambient temperature i & iii b) ii & iii c) i & iv d) i & ii

Last Answer : d) i & ii