Description : Though the effective depth of a T-beam is the distance between the top compression edge to the centre of the tensile reinforcement, for heavy loads, it is taken as (A) 1/8th of the span (B) 1/10th of the span (C) 1/12th of the span (D) 1/16th of the span
Last Answer : Answer: Option C
Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 16 m effective span is 10 kg/cm2 , the length of the beam having nominal reinforcement, is (A) 8 cm (B) 6 m (C) 8 m (D) 10 m
Description : In the design of a front counterfort in a counterfort retaining wall, the main reinforcement is provided on (i) Bottom face near counterfort (ii) Top face near counterfort (iii) Bottom face near centre of span (iv) Top ... ) (B) Only (ii) (C) Both (i) and (iv) (D) Both (ii) and (iii)
Description : In a counterfort retaining wall, the main reinforcement in the stem at mid span is provided on (A) Front face only (B) Inner face only (C) Both front face and inner face (D) None of the above
Last Answer : Answer: Option A
Description : The size of the mesh at each corner meant for torsion reinforcement in a rectangular slab of size (Lx ´ Ly) is Lx = shorter span Lx = Longer span [ A ] 0.1 Ly x 1 Ly [ B ] 0.2 Ly x 0.2 Ly [ C ] 0.1 Lx x 0.1 Lx [ D ] 0.2 Lx x 0.2 Lx
Last Answer : [ D ] 0.2 Lx x 0.2 Lx
Description : The reinforcement in a continuous slab is provided (a) At the top of the slab portion over the intermediate supports. (b) At the bottom of the slab portion over the intermediate supports. (c) All the middle of the slab portion over the intermediate supports (d) All the above
Last Answer : (a) At the top of the slab portion over the intermediate supports.
Description : Depth of reinforcement below the surface of a concrete pavement, is generally kept (A) 5 cm (B) 6 cm (C) 7 m (D) 9 m
Description : In a simply supported reinforced concrete beam, the reinforcement is placed. (a) Above the neutral axis (b) Below the neutral axis (c) At the neutral axis (d) None of these
Last Answer : (b) Below the neutral axis
Description : The slab is designed as one way if the ratio of long span to short span is (A) Less than 1 (B) Between 1 and 1.5 (C) Between 1.5 and 2 (D) Greater than 2
Last Answer : Answer: Option D
Description : When the slab is supported on all the four edges and the ratio of long span to short span is small, bending takes place along both the spans, such a slab is known as (a) Slab spanning in one direction (b) One way slab. (c) Slab spanning in two direction. (d) Two-way slab.
Last Answer : (d) Two-way slab.
Description : The moments developed in the slab are influenced by the following factors i.Short span ii.Long span iii.Type of supporting edge. iv.Magnitude and type of load on slab [ A ] i, iii and iv [ B ] ii ,iii and iv [ C ] i and iii [ D ] i, ii , iii and iv
Last Answer : [ D ] i, ii , iii and iv
Description : In a two way slab flexural bending develops [ A ] Along short span [ B ] Along long span [ C ] In Mutually perpendicular directions [ D ] At the center of short span
Last Answer : [ C ] In Mutually perpendicular directions
Description : A trolley wire weighs 1.2 kg per meter length. The ends of the wire are attached to two poles 20 meters apart. If the horizontal tension is 1500 kg find the dip in the middle of the span (A) 2.5 cm (B) 3.0 cm (C) 4.0 cm (D) 5.0 cm
Last Answer : (C) 4.0 cm
Description : According to I.S. : 456, slabs which span in two directions with corners held down, are assumed to be divided in each direction into middle strips and edge strips such that the width of the middle strip, is ... (C) Three-fourth of the width of the slab (D) Four-fifth of the width of the slab
Description : square cross section b/h/h'=400/400/40mm with a reinforcement ratio of p=0.015 is loaded for action forces of axial load plus uniaxial bending.the column is to be made of C25/30 concrete & S-460 steel.check whether the column AB is short or long?
Last Answer : 10001/999900
Description : An 80-year-old woman has a three month history of progressive numbness and unsteadiness of her gait. On examination, there is a mild spastic paraparesis, with brisk knee reflexes, ankle ... dorsal meningioma C. multiple sclerosis D. subacute combined degeneration of the cord E. tabes dorsalis
Last Answer : Ans: B
Description : Why should you always try to use short, clear sentences on your web pages? A. Readers do not trust longer sentences B. Readers cannot read long sentences C. Readers have a short attention span D. Longer sentences can be confusing to readers
Last Answer : C. Readers have a short attention span
Description : In the design of a simply supported skew bridge, which direction of reinforcement should be provided?
Last Answer : In the conventional design of steel reinforcement for a simply supported skew bridge, a set of reinforcement is usually placed parallel to free edge while the other set is designed parallel ... ). In this way, considerable savings would be obtained from the orthogonal arrangement of reinforcement.
Description : What are the three major types of reinforcement used in prestressing?
Last Answer : i) Spalling reinforcement Spalling stresses are established behind the loaded area of anchor blocks and this causes breaking away of surface concrete. These stresses are induced by strain incompatibility with ... of action of the load. Reinforcement is needed to resist these lateral tensile forces.
Description : The shear reinforcement in R.C.C. is provided to resist (A) Vertical shear (B) Horizontal shear (C) Diagonal compression (D) Diagonal tension
Description : The amount of reinforcement for main bars in a slab, is based upon (A) Minimum bending moment (B) Maximum bending moment (C) Maximum shear force (D) Minimum shear force
Last Answer : Answer: Option B
Description : In a singly reinforced beam, the effective depth is measured from its compression edge to (A) Tensile edge (B) Tensile reinforcement (C) Neutral axis of the beam (D) Longitudinal central axis
Description : Distribution reinforcement in a simply supported slab, is provided to distribute (A) Load (B) Temperature stress (C) Shrinkage stress (D) All the above
Description : If diameter of a reinforcement bar is d, the anchorage value of the hook is (A) 4d (B) 8d (C) 12d (D) 16d
Description : The maximum area of tension reinforcement in beams shall not exceed (A) 0.15 % (B) 1.5 % (C) 4 % (D) 1 %
Description : An R.C.C. beam not provided with shear reinforcement may develop cracks in its bottom inclined roughly to the horizontal at (A) 25° (B) 35° (C) 45° (D) 55°
Description : The percentage of minimum reinforcement of the gross sectional area in slabs, is (A) 0.10 % (B) 0.12 % (C) 0.15 % (D) 0.18 %
Description : In a beam the local bond stress Sb, is equal to (A) Shear force/(Leaver arm Total perimeter of reinforcement) (B) Total perimeter of reinforcement/(Leaver arm Shear force) (C) ... force Total perimeter of reinforcement) (D) Leaver arm/(Bending moment Total perimeter of reinforcement)
Description : The length of lap in tension reinforcement should not be less than the bar diameter × (actual tension / four times the permissible average bond stress) if it is more than (A) 18 bar diameters (B) 24 bar diameters (C) 30 bar diameters (D) 36 bar diameters
Description : Minimum spacing between horizontal parallel reinforcement of different sizes, should not be less than (A) One diameter of thinner bar (B) One diameter of thicker bar (C) Twice the diameter of thinner bar (D) None of these
Description : If the diameter of the main reinforcement in a slab is 16 mm, the concrete cover to main bars is (A) 10 mm (B) 12 mm (C) 14 mm (D) 16 mm
Description : If the shear stress in a R.C.C. beam is (A) Equal or less than 5 kg/cm2 , no shear reinforcement is provided (B) Greater than 4 kg/cm2 , but less than 20 kg/cm2 , shear reinforcement is provided (C) Greater than 20 kg/cm2 , the size of the section is changed (D) All the above
Description : The diameter of transverse reinforcement of columns should be equal to one-fourth of the diameter of the main steel rods but not less than (A) 4 mm (B) 5 mm (C) 6 mm (D) 7 mm
Description : A part of the slab may be considered as the flange of the T-beam if (A) Flange has adequate reinforcement transverse to beam (B) It is built integrally with the beam (C) It is effectively bonded together with the beam (D) All the above
Description : Pick up the assumption for the design of a pre-stressed concrete member from the following: (A) A transverse plane section remains a plane after bending (B) During deformation limits, Hook's ... of stress in reinforcement due to changes in external loading is negligible (D) All the above
Description : As per IS : 456, the reinforcement in a column should not be less than (A) 0.5% and not more than 5% of cross-sectional area (B) 0.6% and not more than 6% of cross-sectional area (C) 0.7% and not more than 7% of cross-sectional area (D) 0.8% and not more than 8% of cross-sectional area
Description : In a slab, the pitch of the main reinforcement should not exceed its effective depth (A) Three times (B) Four times (C) Five times (D) Two times
Description : Side face reinforcement shall be provided in the beam when depth of the web in a beam exceeds (A) 50 cm (B) 75 cm (C) 100 cm (D) 120 cm
Description : The transverse reinforcements provided at right angles to the main reinforcement (A) Distribute the load (B) Resist the temperature stresses (C) Resist the shrinkage stress (D) All the above
Description : In the zone of R.C.C. beam where shear stress is less than 5 kg/cm2 , nominal reinforcement is provided at a pitch of (A) One-half lever arm of the section (B) One-third lever arm of the section (C) Lever arm of the section (D) One and half lever arm of the section
Description : Pick up the incorrect statement from the following: (A) In the stem of a retaining wall, reinforcement is provided near the earth side (B) In the toe slab of a retaining wall, reinforcement is ... slab of a retaining wall, reinforcement is provided at the top of the slab (D) None of these
Description : The spacing of transverse reinforcement of column is decided by the following consideration. (A) The least lateral dimension of the column (B) Sixteen times the diameter of the smallest longitudinal ... column (C) Forty-eight times the diameter of transverse reinforcement (D) All the above
Description : Pick up the incorrect statement from the following: Tensile reinforcement bars of a rectangular beam (A) Are curtailed if not required to resist the bending moment (B) Are bent up at suitable ... to serve as shear reinforcement (D) Are maintained at bottom to provide at least local bond stress
Description : Minimum spacing between horizontal parallel reinforcement of the same size should not be less than (A) One diameter (B) 2.5 diameters (C) 3 diameters (D) 3.5 diameters
Description : Lapped splices in tensile reinforcement are generally not used for bars of size larger than (A) 18 mm diameter (B) 24 mm diameter (C) 30 mm diameter (D) 36 mm diameter
Description : Pick up the correct statement from the following: (A) Lateral reinforcement in R.C.C. columns is provided to prevent the longitudinal reinforcement from buckling (B) Lateral reinforcement prevents ... Lateral reinforcement stops breaking away of concrete cover, due to buckling (D) All the above
Description : Reinforcement in cement concrete slab of road pavements, is placed (A) Longitudinally (B) Transversely (C) Longitudinally and transversely (D) In the form of welded wire mesh
Description : The unit of measurement is per quintal for the following: (A) Collapsible gates with rails (B) Rolling shutters (C) Expanded metal wire netting (D) M.S. reinforcement of R.C.C. works
Last Answer : (D) M.S. reinforcement of R.C.C. works
Description : Pick up the incorrect statement from the following: (A) No deduction is made for the volume occupied by reinforcement (B) No deduction is made for the openings upto 0.1 sq.m (C) No deduction is made for volumes occupied by pipes, not exceeding 100 sq.cm in crosssection (D) None of these
Last Answer : (D) None of these
Description : Maximum percentage reinforcement in case of slabs is limited to (A) 2 (B) 4 (C) 6 (D) 8
Last Answer : (B) 4