Description : As per IS:1139, the characteristic yield strength for cold twisted deformed bars is [ A ] 250 N/mm2 [ B ] 415 N/mm2 [ C ] 500 N/mm2 [ D ] 550 N/mm2
Last Answer : [ C ] 500 N/mm2
Description : As per IS: 1139, permissible stress in compression steel reinforcement for High Yield strength deformed bars is [ A ] 140 N/mm2 [ B ] 190 N/mm2 [ C ] 230 N/mm2 [ D ] 415 N/mm2
Last Answer : [ B ] 190 N/mm2
Description : If high yield strength deformed bars are used, the are of distribution reinforcement in slabs, should not less than. (a) 0.12% of the gross area of concrete (b) 0.15% of the gross area of concrete (c) 0.18% of the gross area of concrete (d) 0.20% of the gross area of concrete
Last Answer : (a) 0.12% of the gross area of concrete
Description : Minimum reinforcement in slabs, when High yield strength deformed bars [ A ] 0.12% of gross cross sectional area [ B ] 0.15% of gross cross sectional area [ C ] 0.20% of gross cross sectional area [ D ] 0.25% of gross cross sectional area.
Last Answer : [ A ] 0.12% of gross cross sectional area
Description : A simply supported rolled steel joist 8 m long carries a uniformly distributed load over it span so that the maximum bending stress is 75 N/mm². If the slope at the ends is 0.005 radian and the value of E = 0.2 ... joist, is (A) 200 mm (B) 250 mm (C) 300 mm (D) 400 mm
Last Answer : (D) 400 mm
Description : The percentage of reinforcement in case of slabs, when high strength deformed bars are used is not less than (A) 0.15 (B) 0.12 (C) 0.30 (D) 1.00
Last Answer : Answer: Option B
Description : As per IS: 456, permissible bond stress for plain bars in tension, in working stress method, where M20, is the grade of concrete [ A ] 0.6 N/mm2 [ B ] 0.8 N/mm2 [ C ] 1.0 N/mm2 [ D ] 1.2 N/mm2
Last Answer : [ B ] 0.8 N/mm2
Description : Hot extrusion of aluminium is done in the temperature range of __________ °C. (A) 550-600 (B) 450-500 (C) 350-400 (D) 250-300
Last Answer : (C) 350-400
Description : A square object of 4 mm is subjected to a force of 3000 N. What is the maximum allowable shear stress acting on it? a. 250.14 mm2 b. 281.25 mm2 c. 400.32 mm2 d. 500 mm2
Last Answer : b. 281.25 mm2
Description : The most critical consideration in the design of a rolled steel column carrying axial loads is the (a) Percentage elongation at yield and the net cross-sectional area (b) Critical bending ... at ultimate load (d) Compressive strength based on slenderness ratio and gross cross-sectional area.
Last Answer : (d) Compressive strength based on slenderness ratio and gross cross-sectional area.
Description : If a concrete column 200 200 mm in cross-section is reinforced with four steel bars of 1200 mm2 total cross-sectional area. Calculate the safe load for the column if permissible stress in concrete is 5 N/mm2 ... 15 Ec (A) 264 MN (B) 274 MN (C) 284 MN (D) 294 MN
Last Answer : (C) 284 MN
Description : A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2 MN/mm2 and Eb = 0.1 ... 6 N/mm2 s = 12 N/mm2 (D) b = 5 N/mm2 s = 10 N/mm
Last Answer : (A) b = 10 N/mm2 s = 20 N/mm
Description : The ultimate average anchorage bond stress for plain bars in tension is _______ if the grade of concrete is M20 [ A ] 1.60 N/mm2 [ B ] 1.92 N/mm2 [ C ] 2.24 N/mm2 [ D ] 2.40 N/mm2
Last Answer : [ B ] 1.92 N/mm2
Description : A steel bar 5 m × 50 mm is loaded with 250,000 N. If the modulus of elasticity of the material is 0.2 MN/mm2 and Poisson's ratio is 0.25, the change in the volume of the bar is: (A) 1.125 cm3 (B) 2.125 cm3 (C) 3.125 cm3 (D) 4.125 cm
Last Answer : (C) 3.125 cm
Description : A steel rod of sectional area 250 sq. mm connects two parallel walls 5 m apart. The nuts at the ends were tightened when the rod was heated to 100°C. If steel = 0.000012/C°, Esteel = 0.2 MN/mm2 , the ... N/mm2 (B) 100 N/mm2 (C) 120 N/mm2 (D) 150 N/mm2 Answer: Option
Last Answer : (C) 120 N/mm
Description : Which of the following has high tensile strength? (A) Plain hot rolled wires (B) Cold drawn wires (C) Heat treated rolled wires (D) All have same tensile strength
Description : According to IS: 456-2000 the ultimate moment of resistance of a slab for Fe - 415 HYSD bars is; [ A ] Mu = 0.138 fck bd2 [ B ] Mu = 0.145 fck bd2 [ C ] Mu = 0.152 fck bd2 [ D ] Mu = 0.165 fck bd2
Last Answer : [ A ] Mu = 0.138 fck bd2
Description : In working stress design, permissible bond stress in the case of deformed bars is more than that in plain bars by (A) 10 % (B) 20 % (C) 30 % (D) 40 %
Last Answer : (D) 40 %
Description : In the reinforced cement concrete structure, the steel reinforcement consists of . (a) Deformed bars (b) Cold twisted bars (c) Mildsteel and medium tensile steel bars (d) All of these
Last Answer : (d) All of these
Description : The bond stress for deformed bars is more than that in plain bars by [ A ] 25% [ B ] 40% [ C ] 60% [ D ] 50%
Last Answer : [ B ] 40%
Description : For lime concrete, (A) Slump is 50 to 75 mm (B) Flexural strength at 90 days is 0.2 N/mm2 (C) Compressive strength at 90 days is 1.5 N/mm2 (D) All the above
Last Answer : Answer: Option D
Description : The ultimate tensile strength of structural mild steel is about (A) 160 N/mm² (B) 260 N/mm² (C) 420 N/mm² (D) 520 N/mm
Last Answer : Answer: Option C
Description : The compressive strength an ordinary Portland cement (1:3) after 7 days test should not be less than. (a) 11N/mm2 (b) 17.5 N/mm2 (c) 22 N/mm2 (d) 27.5N/m2
Last Answer : (b) 17.5 N/mm2
Description : Minimum compressive strength of cement required at the age of 3 days for ordinary Portland cement of grade 33 is [ A ] 1.15 N/mm2 [ B ] 11.5 N/mm2 [ C ] 2.10 N/mm2 [ D ] 21 N/mm2
Last Answer : [ B ] 11.5 N/mm2
Description : A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2
Last Answer : (c) 125/p N/mm2
Description : Side face reinforcement is provided when the depth of beam exceeds [ A ] 250 mm [ B ] 450 mm [ C ] 550 mm [ D ] 750 mm
Last Answer : [ D ] 750 mm
Description : The Young's modulus of elasticity of steel, is (A) 150 KN/mm2 (B) 200 KN/mm2 (C) 250 KN/mm2 (D) 275 KN/mm
Description : The modules of elasticity of steel shall be taken as (a) 100kN/mm2 (b) 200 kN/mm2 (c) 250 kN/mm2 (d) 300 kN/mm2
Last Answer : (b) 200 kN/mm2
Description : The design yield stress of steel according to IS: 4561978 is: (A) 0.37 fy (B) 0.57 fy (C) 0.67 fy (D) 0.87 fy Where fy is the characteristic yield strength of steel
Description : Consider the following statements: Percentage of steel for balanced designed of a singly reinforced rectangular section by limit state method depends on (1) Characteristic strength of concrete (2) Yield strength of concrete (3) Modulus of elasticity ... (b) 1, 3 and 4 (c) 1, 2 and 4 (d) 1, 2 and 3
Last Answer : 1,2,4
Description : Stress may be expressed in Newtons (A) Per millimetre square (N/mm2 ) (B) Per centimetre square (N/cm2 ) (C) Per metre square (N/m2 ) (D) None of these
Last Answer : (A) Per millimetre square (N/mm2 )
Description : As per IS :456-1978, the permissible value of bond – stress for M15 grade of concrete is (a) 0.5 N/mm2 (b) 1 N/mm2 (c) 1.5 N/mm2 (d) 2 N/mm2
Last Answer : (b) 1 N/mm2
Description : As per IS:456, maximum shear stress for M20 glade concrete in working stress method is [ A ] 1.6 N/mm2 [ B ] 1.8 N/mm2 [ C ] 2.0 N/mm2 [ D ] 2.2 N/mm2
Last Answer : [ B ] 1.8 N/mm2
Description : As per IS: 456, permissible direct compressive stress M20 grade concrete in working stress method of designer [ A ] 5.0 N/mm2 [ B ] 7.0 N/mm2 [ C ] 10.0 N/mm2 [ D ] 20.0 N/mm2
Last Answer : [ A ] 5.0 N/mm2
Description : As per IS;456, in working stress method of design, permissible tensile stress for M20 grade concrete is given by [ A ] 1. 2 N/mm2 [ B ] 1.5 N/mm2 [ C ] 2.0 N/mm2 [ D ] 2.8 N/mm2
Last Answer : [ D ] 2.8 N/mm2
Description : As per IS: 456-2000, recommended value for standard deviation for concrete mix from M30 to M50 is [ A ] 1 N/mm2 [ B ] 2 N/mm2 [ C ] 4 N/mm2 [ D ] 5 N/mm2
Last Answer : [ D ] 5 N/mm2
Description : As per IS: 456-2000, modulus of elasticity of concrete (in N/mm2) is given by [ A ] 5700 vfCK [ B ] 5000 vfCK [ C ] 3700 vfCK [ D ] 3000 vfCK
Last Answer : [ B ] 5000 vfCK
Description : The monthly incomes of A and B are in the ratio 4:5, their expenses are in the ratio 5 : 6. If 'A' saves Rs.25 per month and 'B' saves Rs.50 per month, what are their respective incomes? A) Rs.400 and Rs.500 B) Rs.240 and Rs.300 C) Rs.320 and Rs.400 D) Rs.440 and Rs.550 E) NONE
Last Answer : Answer: A Let AA's income be = 4x AA's expenses, therefore = 4x–25 Let BB's income be = 5x BB's expenses, therefore = 5x–50 We know that the ratio of their expenses = 5:6 ⇒24x−150=25x−250 ⇒ Therefore, x=100 A's income =4x=400 and B's income =5x=500
Description : The value of 'C' of Indian type W.C. shown in the given figure is: (A) 400 mm (B) 450 mm (C) 500 mm (D) 550 mm
Last Answer : (C) 500 mm
Description : Number of bricks required for one cubic metre of brick masonry is (A) 400 (B) 450 (C) 500 (D) 550
Description : Sum of tread and rise must lie between (A) 300 to 350 mm (B) 400 to 450 mm (C) 500 to 550 mm (D) 600 to 650 mm
Description : If yielding strength=400N/mm2, the find the permissible shear stress according to ASME standards. a) 72 N/mm2 b) 76 N/mm2 c) 268 N/mm2 d) 422 N/mm2
Last Answer : a) 72 N/mm2
Description : What is the electric field intensity at a distance of 20cm from a charge 2 X 10 -6 C in vacuum? a) 250,000 b) 350,000 c) 450,000 d) 550,000
Last Answer : c) 450,000
Description : An R.C.C. column of 30 cm diameter is reinforced with 6 bars 12 mm placed symmetrically along the circumference. If it carries a load of 40, 000 kg axially, the stress is (A) 49.9 kg/cm2 (B) 100 kg/cm2 (C) 250 kg/cm2 (D) 175 kg/cm
Last Answer : Answer: Option A
Description : The Maximum spacing of the longitudinal bars measured long the periphery of the column should be [ A ] 250 mm [ B ] 300 mm [ C ] 400 mm [ D ] 450 mm
Last Answer : [ B ] 300 mm
Description : A dice is rolled 250 times, and the outcoms 1, 2, 3, 4, 5 and 6 occurred as given in the following table: Find the probalility of getting an odd numbe
Last Answer : A dice is rolled 250 times, and the outcoms 1, 2, 3, 4, 5 and 6 occurred as given ... table: Find the probalility of getting an odd number.
Description : When shear stress exceeds the permissible limit in a slab, then it is reduced by (A) Increasing the depth (B) Providing shear reinforcement (C) Using high strength steel (D) Using thinner bars but more in number
Description : A cantilever of length 2 cm and depth 10 cm tapers in plan from a width 24 cm to zero at its free end. If the modulus of elasticity of the material is 0.2 × 106 N/mm2 , the deflection of the free end, is (A) 2 mm (B) 3 mm (C) 4 mm (D) 5 mm
Last Answer : (D) 5 mm
Description : A steel bar 20 mm in diameter simply-supported at its ends over a total span of 40 cm carries a load at its centre. If the maximum stress induced in the bar is limited to N/mm2, the bending strain energy stored in the ... (A) 411 N mm (B) 511 N mm (C) 611 N mm (D) 711 N mm
Last Answer : (C) 611 N mm